SLD333V

SLD333V 1W High Power Laser Diode Description The SLD333V is a 1W high power laser diode designed to have a uniform emission area that is suitable for the applications of measurement and printing, etc. It adopts a φ9 package that is easy to handle. Features • High power Recommended optical power output: Po = 1W • High-optical power density: 1W/100µm (Emitting line width) Structure AlGaAs Quantum Well structure laser diode Absolute Maximum Ratings (Tc = 25°C) • Optical power output Pomax 1.1 • Reverse voltage VR LD 3 PD 15 • Operating temperature (Tc) Topr –10 to +30 • Storage temperature Tstg –50 to +85 Operating Lifetime MTTF 10,000H (effective value) at Po = 1W, Tc = 25°C Warranty This warranty period shall be 90 days after receipt of the product or 1,000 hours operation time whichever is shorter. Sony Quality Assurance Department shall analyze any product that fails during said warranty period, and if the analysis results show that the product failed due to material or manufacturing defects on the part of Sony, the product shall be replaced free of charge. Laser diodes naturally have differing lifetimes which follow a Weibull distribution. Pin Configuration M-248 W V V °C °C 2 1 3 1. LD cathode 2. PD anode 3. COMMON Bottom View Sony reserves the right to change products and specifications without prior notice. This information does not convey any license by any implication or otherwise under any patents or other right. Application circuits shown, if any, are typical examples illustrating the operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits. –1– E03723-PS SLD333V Electrical and Optical Characteristics (Tc = 25°C) Item Threshold current Operating current Operating voltage Wavelength Radiation angle Positional accuracy Parallel Perpendicular Angle Position Differential efficiency Monitor current Ith Iop Vop λp θ// θ⊥ ∆φ// ∆φ⊥ ∆X, ∆Y ηD Imon Po = 1.0W Po = 1.0W Po = 1.0W Po = 1.0W Po = 1.0W Po = 1.0W Po = 1.0W Symbol Conditions Min. — — — 790 4 27 — — — 0.5 0.3 Typ. 0.2 1.2 2.0 — 9 32 — — — 0.9 1.5 Tc: Case temperature Max. 0.5 1.5 3.0 840 15 40 ±5 ±3 ±50 — 6 Unit A A V nm degree degree degree degree µm W/A mA –2– SLD333V Notes on Operation Care should be taken for the following points when using this product. (1) This product corresponds to a Class 4 product under IEC60825-1 and JIS standard C6802 "Laser Product Emission Safety Standards". LASER DIODE LASER DIODE This product complies with 21 CFR Part 1040.10 and 1040.11 LASER RADIATION AVOID EYE OR SKIN EXPOSURE TO DIRECT OR SCATTERED RADIATION Sony Corporation AVOID EXPOSURE Laser radiation is emitted from this aperture. 6-7-35 Kitashinagawa, Shinagawa-ku,Tokyo 141-0001 Japan MAXIMUM OUTPUT WAVELENGTH OVER 1 W 600 - 950 nm CLASS IV LASER PRODUCT (2) Eye protection against laser beams Take care not to allow laser beams to enter your eyes under any circumstances. For observing laser beams, always use safety goggles that block laser beams. Usage of IR scopes, IR cameras and fluorescent plates is also recommended for monitoring laser beams safely. (3) Gallium Arsenide This product uses gallium arsenide (GaAs). This is not a problem for normal use, but GaAs vapors may be potentially hazardous to the human body. Therefore, never crush, heat to the maximum storage temperature or higher, or place the product in your mouth. In addition, the following disposal methods are recommended when disposing of this product. 1. Engaging the services of a contractor certified in the collection, transport and intermediate treatment of items containing arsenic. 2. Managing the product through to final disposal as specially managed industrial waste which is handled separately from general industrial waste and household waste. (4) Prevention of surge current and electrostatic discharge Laser diodes are most sensitive to electrostatic discharge among semiconductors. When a large current is passed through the laser diode for even an extremely short time, the strong light emitted from the laser diode promotes deterioration and then destruction of the laser diode. Therefore, note that surge current should not flow to the laser diode driving circuit from switches and others. Also, if the laser diode is handled carelessly, it may be destroyed instantly because electrostatic discharge is easily applied by a human body. Therefore, be extremely careful about overcurrent and electrostatic discharge. (5) Use for special applications This product is not designed or manufactured for use in equipment used under circumstances where failure may pose a risk to life and limb, or result in significant material damage, etc. Consult your Sony sales representative when investigating use for medical, vehicle, nuclear power control or other special applications. Also, use the power supply that was designed not to exceed the optical power output specified at the absolute maximum ratings. –3– SLD333V Package Outline Unit: mm M-248 (LO-11) Reference Slot 1.0 0.4 3 2 1 Photo Diode 0 φ9.0 – 0.015 φ7.7 MAX φ6.9 MAX φ3.5 0.6 MAX Window Glass Reference Plane LD Chip 3 – φ0.45 ∗Optical Distance = 2.55 ± 0.05 PCD φ2.54 SONY CODE EIAJ CODE JEDEC CODE M-248 PACKAGE MASS 7.0 MAX 1.5 3.4 MAX ∗2.45 1.2g –4– Sony Corporation