B-13-14-1250C-T-SSC-G5

1.25 Gbps Bi-directional Receptacle Single Fiber Transceiver B-13/14-1250(C)-T3-SSC Features • Diplexer Single Mode Single Fiber 1x9 SC Receptacle Connector • Wavelength Tx 1310 nm/Rx 1490 nm • IEEE 802.3 Compliant • Single +3.3V power Supply • PECL/LVPECL Differential Inputs and Output [B-13/14-1250-T3-SSC] • TTL/LVTTL Signal Detection Output Optional [B-13/14-1250C-T3-SSC] • Wave Solderable and Aqueous Washable • LED Multisourced 1x9 Transceiver Interchangeable • Class 1 Laser Int. Safety Standard IEC 825 Compliant • Uncooled Laser diode with MQW structure • Complies with Telcordia (Bellcore) GR-468-CORE • RoHS compliance available Absolute Maximum Rating Parameter Power Supply Voltage Input Voltage Output Current Soldering Temperature Storage Temperature Symbol Vcc - Min. 0 0 -40 Max. 3.6 Vcc 30 260 85 Unit V V mA ºC ºC Note Iout - 10 seconds on leads only Tstg Recommended Operating Condition Parameter Power Supply Voltage Operating Temperature (Case) Operating Temperature (Case) Data Rate Symbol Vcc Topr Topr - Min. 3.1 0 -40 - Typ. 3.3 1250 Max. 3.5 70 85 - Unit V ºC ºC Mbps Transmitter Specifications (Optical) Parameter Optical Transmit Power Output center Wavelength Output Spectrum Width Extinction Ratio Output Eye Optical Rise Time Optical Fall Time Optical Isolation Relative Intensity Noise Total Jitter Symbol Po λ ∆λ ER Tr Tf - Min -10 1260 9 30 - Typical 1310 - Max -3 1360 3 0.26 0.26 -116 0.27 Unit dBm nm nm dB ns ns dB dB/Hz ns 20% to 80% Values 20% to 80% Values RMS (σ) Notes Output power is coupled into a 9/125 µm single mode fiber Compliant with IEEE 802.3 Tx:1310 nm/ Rx:1490 nm Measured with 27-1 PRBS RIN TJ LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 1 LUMNDS1828-May1308 Rev A.0 1.25 Gbps Bi-directional Receptacle Single Fiber Transceiver B-13/14-1250(C)-T3-SSC Transmitter Specifications (Electrical) Parameter Power Supply Current Data Input Current-Low Data Input Current-High Differential Input Voltage Data Input Voltage-Low Data Input Voltage-High Symbol ICC IIL IIH VIH-VIL VIL-VCC VIH-VCC Min -350 300 -2.0 -1.1 Typical - Max 160 350 -1.58 -0.74 Unit mA µA µA mV V V Notes Maximum current is specified at Vcc= Maximum @ maximum temperature These inputs are compatible with 10K, 10KH and 100K ECL and PECL inputs Receiver Specifications (Optical) Parameter Sensitivity Maximum Input Power Signal Detect-Asserted Signal Detect-Deasserted Signal Detect-Hysteresis Cross Talk Wavelength of Operation Symbol Pin Pa Pd - Min 0 -38 1.0 1470 Typical - Max -22 -22 -33 1600 Unit dBm dBm dBm dBm dB dB nm Notes Measured with 27-1 PRBS, BER = 10-12 Measured on transition: low to high(Note1) Measured on transition: high to low(Note1) Note 1: The SD level should be deasserted when fiber disconnected Receiver Specifications (Electrical) Parameter Power Supply Current Data output Voltage-Low Data output Voltage-High Signal Detect output Voltge-Low Signal Detect Output Voltge-High Signal Detect output Voltge-Low Signal Detect Output Voltge-High Symbol ICC VOL -Vcc VOH- Vcc VSDL-Vcc VSDH- Vcc V SDL V SDH Min -2.0 -1.1 -2.0 -1.1 -20 Typical - Max 100 -1.58 -0.74 -1.58 -0.74 0.5 - Unit mA V V V V V V Note The current excludes the output load current These outputs are compatible with 10K, 10KH and 100KECL and PECL outputs B-13/14-1250-T3-SSC B-13/14-1250C-T3-SSC LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 2 LUMNDS1828-May1308 Rev A.0 1.25 Gbps Bi-directional Receptacle Single Fiber Transceiver B-13/14-1250(C)-T3-SSC Connection Diagram 1. (Rx GND) 2. (Rx +) 3. (Rx-) 4. (SD) 5. (Rx Vcc) 6. (Tx Vcc) 7. (TX-) 8. (TX+) 9. (Tx GND) NC Top View NC Receiver Signal Ground Receiver Data Out Receiver Data Out Bar Signal Detect Receiver Power Supply Transmitter Power Supply Transmitter Data In Bar Transmitter Data in Transmitter Signal Ground PIN 1 2 3 4 5 6 7 8 Warnings 9 Symbol RxGND RD+ RDSD RxVcc TxVcc TDTD+ TxGND Notes Directly connect this pin to the receiver ground plane See recommended circuit schematic See recommended circuit schematic Active high on this indicates a received optical signal DC power for the receiver section DC power for the transmitter section See recommended circuit schematic See recommended circuit schematic Directly connect this pin to the transmitter ground plane LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 3 LUMNDS1828-May1308 Rev A.0 1.25 Gbps Bi-directional Receptacle Single Fiber Transceiver B-13/14-1250(C)-T3-SSC Recommended Circuit Schematic (PECL SD) B-13/14-1250-T3-SSC Tx Vcc C5 Rx Vcc 9 R1 R3 8 7 65 43 2 1 R9 R5 R7 C6 TD + TD - RD + RD - Tx Vcc Rx Vcc R2 R4 SD R10 No internal connection Transceiver Top view No internal connection R6 R8 L1 Notes +3.3V: R1=R3=R5=R7=R9=130 R2=R4=R6=R8=R10=82 C1=C2=C3=C5=C6=0.1F C4=10F L1=L2=1H Vcc C3 L2 C4 C1 Rx Vcc C2 Tx Vcc Recommended Circuit Schematic (TTL SD) B-13/14-1250C-T3-SSC Tx Vcc C5 Rx Vcc 98 R1 R3 7 65 432 1 R5 R7 C6 TD + TD - RD + RD - Tx Vcc Rx Vcc R2 R4 SD R6 R8 No internal connection Transceiver Top view No internal connection L1 Notes +3.3V: R1=R3=R5=R7=130 R2=R4=R6=R8=82 C1=C2=C3=C5=C6=0.1F C4=10F L1=L2=1H Vcc C3 L2 C4 C1 Rx Vcc C2 Tx Vcc The split-loaded terminations for ECL signals need to be located at the input of devices receiving those ECL signals. The power supply filtering is required for good EMI performance. Use short tracks from the inductor L1/L2 to the module Rx Vcc. A GND plane under the module is required for good EMI and sensitivity performance. LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 4 LUMNDS1828-May1308 Rev A.0 1.25 Gbps Bi-directional Receptacle Single Fiber Transceiver B-13/14-1250(C)-T3-SSC Package Diagram B-13/14-1250(C)-T3-SSC Units in mm LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 5 LUMNDS1828-May1308 Rev A.0 1.25 Gbps Bi-directional Receptacle Single Fiber Transceiver B-13/14-1250(C)-T3-SSC Ordering Information Available Options: B-13/14-1250-T3-SSC-G5 B-13/14-1250C-T3-SSC-G5 B-13/14-1250-T3-SSCA-G5 B-13/14-1250C-T3-SSCA-G5 Part numbering Definition: B - 13/14 - 1250(C) - T - S SC Tx Power Temperature • Wavelength Tx Wavelength=1310nm Rx Wavelength=1490nm • Communication protocol (1250 Gbps) 1250= PECL SD Output 1250C= TTL SD Output • T = +5 V Transceiver T3 = +3.3V Transceiver • Single mode fiber • Connector options • Tx Power Blank = -10 to -3 dBm -RoHS • Temperature range Blank = industrial temperature(0 to 70 ºC) A = industrial temperature(-40 to 85 ºC) • RoHS Compliance options G5 = RoHS 5/6-compliant product (lead exemption) LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 6 LUMNDS1828-May1308 Rev A.0 1.25 Gbps Bi-directional Receptacle Single Fiber Transceiver B-13/14-1250(C)-T3-SSC Warnings Handling Precautions: This device is susceptible to damage as a result of electrostatic discharge (ESD). A static free environment is highly recommended. Follow guidelines according to proper ESD procedures. Laser Safety: Radiation emitted by laser devices can be dangerous to human eyes. Avoid eye exposure to direct or indirect radiation. Legal Notice IMPORTANT NOTICE! All information contained in this document is subject to change without notice, at LuminentOIC’s sole and absolute discretion. LuminentOIC warrants performance of its products to current specifications only in accordance with the company’s standard one-year warranty; however, specifications designated as “preliminary” are given to describe components only, and LuminentOIC expressly disclaims any and all warranties for said products, including express, implied, and statutory warranties, warranties of merchantability, fitness for a particular purpose, and non-infringement of proprietary rights. Please refer to the company’s Terms and Conditions of Sale for further warranty information. LuminentOIC assumes no liability for applications assistance, customer product design, software performance, or infringement of patents, services, or intellectual property described herein. No license, either express or implied, is granted under any patent right, copyright, or intellectual property right, and LuminentOIC makes no representations or warranties that the product(s) described herein are free from patent, copyright, or intellectual property rights. Products described in this document are NOT intended for use in implantation or other life support applications where malfunction may result in injury or death to persons. LuminentOIC customers using or selling products for use in such applications do so at their own risk and agree to fully defend and indemnify LuminentOIC for any damages resulting from such use or sale. THE INFORMATION CONTAINED IN THIS DOCUMENT IS PROVIDED ON AN “AS IS” BASIS. Customer agrees that LuminentOIC is not liable for any actual, consequential, exemplary, or other damages arising directly or indirectly from any use of the information contained in this document. Customer must contact LuminentOIC to obtain the latest version of this publication to verify, before placing any order, that the information contained herein is current. © LuminentOIC, Inc. 2003 All rights reserved LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 7 LUMNDS1828-May1308 Rev A.0