B-13-15-1250C-FDFB-SSC2

1.25 Gbps bi-directional SC Receptacle single Fiber Transceiver B-1X/1X-1250C-F(DFB)-SSCx Features • Single Mode Single Fiber 2x5 SFF SC Receptacle connector • Gigabit Ethernet Compliant • Single +3.3V Power Supply • Tx 1310nm/Rx 1550 nm [B-13/15-1250C-F(DFB)-SSCx] • Tx 1550nm/Rx 1310 nm [B-15/13-1250C-F(DFB)-SSCx] • LVPECL Differential Inputs and Outputs • LVTTL Signal Detection Output • Class 1 Laser Int. Safety Standard IEC-825 Compliant • EMI Shielding Finger Optional • RoHS compliance available Absolute Maximum Rating Parameter Power Supply Voltage Input Voltage Output Current Soldering Temperature Storage Temperature Symbol Vcc - Min. 0 0 -40 Max. 3.6 Vcc 30 260 85 Unit V V mA ºC ºC Note Iout - 10 seconds on leads only Tstg Recommended Operating Condition Parameter Power Supply Voltage Operating Temperature (-SSCx(S)) Operating Temperature (-SSCxA(S)) Data Rate Symbol Vcc Topr Topr - Min. 3.1 -5 -40 - Typ. 3.3 1250 Max. 3.5 70 85 - Unit V ºC ºC Mbps LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 1 LUMNDS796-Jan2407 Rev. A.3 1.25 Gbps bi-directional SC Receptacle single Fiber Transceiver B-1X/1X-1250C-F(DFB)-SSCx Transmitter Specifications Parameter Optical Optical Transmit Power Optical Transmit Power Optical Transmit Power Optical Transmit Power Output center Wavelength Output center Wavelength Output Spectrum Width Output Spectrum Width Side Mode Supression Ratio Extinction Ratio Output Eye Optical Rise Time Optical Fall Time Optical Isolation Relative Intensity Noise Total Jitter Symbol Po Po Po Po λ λ ∆λrms ∆λ SMSR ER tr tf RIN TJ Min -9 -5 -3 0 1260 1480 30 9 30 - Typical 1310 1550 - Max -3 0 +2 +5 1360 1580 4 1 260 260 -116 270 Unit dBm dBm dBm dBm nm nm nm nm dB dB ps ps dB dB/Hz ns Notes B-1X/1X-1250C-F(DFB)-SSC B-1X/1X-1250C-FDFB-SSC2 B-1X/1X-1250C-FDFB-SSC3 B-1X/1X-1250C-FDFB-SSC4 B-13/15-1250C-F(DFB)-SSCX B-15/13-1250C-F(DFB)-SSCX RMS(σ), B-1X/1X-1250C-F-SSC -20dB width, B-1X/1X-1250C-FDFB-SSCX B-1X/1X-1250C-FDFB-SSCX Compliant with IEEE 802.3z 20% to 80% Values 20% to 80% Values Measured with 27-1 PRBS Transmitter Specifications Parameter Electrical Supply Current Transmit Enable Voltage Transmit Disable Voltage Data Input Current-Low Data Input Current-High Differential Input Voltage Data Input Voltage-Low Data Input Voltage-High Symbol ICC VEN VDIS IIL IIH VIH-VIL VIL-VCC VIH-VCC Min 0 2 -350 300 -2.0 -1.1 Typical - Max 150 0.8 VCC 350 -1.58 -0.74 Unit mA V V µA µA mV V V Notes Maximum current is specified at Vcc= Maximum @ maximum temperature These inputs are compatible with 10K, 10KH and 100K ECL and PECL inputs LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 2 LUMNDS796-Jan2407 Rev. A.3 1.25 Gbps bi-directional SC Receptacle single Fiber Transceiver B-1X/1X-1250C-F(DFB)-SSCx Receiver Specifications Parameter Optical Sensitivity Maximum Input Power Signal Detect-Asserted Signal Detect-Deasserted Signal Detect-Hysteresis Cross Talk Wavelength of Operation Wavelength of Operation Symbol Pin Pa Pd - Min -3 -38 1 1480 1260 Typical - Max -22 -22 4 -33 1600 1360 Unit dBm dBm dBm dBm dB dB nm nm Notes Measured with 27-1 PRBS,BER= 10-12 Measured on transition: low to high (Note 1) Measured on transition: high to low (Note 1) B-13/15-1250C-F(DFB)-SSCX B-15/13-1250C-F(DFB)-SSCX Note 1: The SD level should be deasserted when fiber disconnected Receiver Specifications Parameter Electrical Supply Current Data Output Voltage-Low Data Output Voltage-High Signal Detect Output Voltage-Low Signal Detect Output Voltage-High Symbol ICC VOL -Vcc VOH- Vcc VSDL VSDH Min -2.0 -1.1 0 2.0 Typical - Max 100 -1.58 -0.74 0.5 Vcc Unit mA V V V V Note The current excludes the output load current These outputs are compatible with 10K, 10KH and 100KECL and PECL outputs LVTTL SD Output LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 3 LUMNDS796-Jan2407 Rev. A.3 1.25 Gbps bi-directional SC Receptacle single Fiber Transceiver B-1X/1X-1250C-F(DFB)-SSCx Connection Diagram PIN 1 2 3 4 5 6 7 8 Warnings 9 10 Symbol RxGND RxVcc SD RDRD+ TxVcc TxGND TxDIS TD+ TD- Notes Directly connect this pin to the receiver ground plane +3.3V dc power for the receiver section Active high on this indicates a received optical signal(LVTTL) Receiver Data Out Bar(LVPECL) Receiver Data Out (LVPECL) +3.3V dc power for the transmitter section Directly connect this pin to the tranmitter ground plane Transmitter disable(LVTTL) Transmitter Data In (LVPECL) Transmitter Data In Bar (LVPECL) LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 4 LUMNDS796-Jan2407 Rev. A.3 1.25 Gbps bi-directional SC Receptacle single Fiber Transceiver B-1X/1X-1250C-F(DFB)-SSCx Recommended Circuit Schematic PHY DEVICE TERMINATE AT TRANSCEIVER INPUTS Vcc(+3.3V) Z=50� TD- 100� LVPECL Z=50� 130� TD+ 130� 10 TD- 9 TD+ 8 TxDIS 7 TxGND 6 1�H TxVcc Tx Disable LVTTL Vcc(+3.3V) C3 Tx Rx C2 10�F RxGND RxVcc RD+ RD- SD 1�H C1 Vcc(+3.3V) RD+ 1 2 3 4 5 Z=50� 100� RD- LVPECL Z=50� 130� 130� Z=50� Vcc(+3.3V) SD LVTTL NOTE:C1=C2=C3=100nF TERMINATE AT DEVICE INPUTS The split-loaded terminations for ECL signals need to be located at the input of devices receiving those ECL signals. The power supply filtering is required for good EMI performance. Use short tracks from the inductor L1/L2 to the module Rx Vcc. A GND plane under the module is required for good EMI and sensitivity performance. LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 5 LUMNDS796-Jan2407 Rev. A.3 1.25 Gbps bi-directional SC Receptacle single Fiber Transceiver B-1X/1X-1250C-F(DFB)-SSCx Recommended Circuit Board Layout DIMENSION IN MILLIMETER (INCHES) NOTES: 1.THIS FIGURE DESCRIBE THE RECOMMAND CIRCUIT BOARD LAYOUT FOR THE SFF TRANSCEIVER. 2.THE HATCHED AREAS ARE KEEP-OUT AREAS RESERVED FOR HOUSING STANDOFF. NO METAL TRACES OR GROUND CONNECTION IN KEEP-OUT AREAS. 3.THE MOUNTING STUDS SHOULD BE SOLDERED TO CHASSIS GROUND FOR MECHANICAL INTEGRITY. LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 6 LUMNDS796-Jan2407 Rev. A.3 1.25 Gbps bi-directional SC Receptacle single Fiber Transceiver B-1X/1X-1250C-F(DFB)-SSCx Package Diagram B-1X/1X-1250C-F(DFB)-SSCX(A) Units: mm Warnings Housing Lead PIN 1 PIN 5 Stand-off Legal Notice Housing Lead Stud Stand-off PIN 10 PIN 6 Stand-off LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 7 LUMNDS796-Jan2407 Rev. A.3 1.25 Gbps bi-directional SC Receptacle single Fiber Transceiver B-1X/1X-1250C-F(DFB)-SSCx Package Diagram B-1X/1X-1250C-F(DFB)-SSCX(A)S Units: mm Matel Finger Stand-off PIN 1 PIN 5 Stand-off Housing Lead Stud PIN 6 Housing Lead PIN 10 Stand-off LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 8 LUMNDS796-Jan2407 Rev. A.3 1.25 Gbps bi-directional SC Receptacle single Fiber Transceiver B-1X/1X-1250C-F(DFB)-SSCx Ordering Information Available Options:  B-13/15-1250C-F-SSC(A)(S)(-G5) B-13/15-1250C-FDFB-SSC(S)(-G5) B-13/15-1250C-FDFB-SSC2(S)(-G5) B-13/15-1250C-FDFB-SSC3(S)(-G5) B-13/15-1250C-FDFB-SSC4(S)(-G5) B-15/13-1250C-F-SSC(A)(S)(-G5) B-15/13-1250C-FDFB-SSC(S)(-G5) B-15/13-1250C-FDFB-SSC2(S)(-G5) B-15/13-1250C-FDFB-SSC3(S)(-G5) B-15/13-1250C-FDFB-SSC4(S)(-G5) Part numbering Definition: B - 1X/1X - 1250C - F(DFB) - S SC Tx Power Operating Temperature Shielding Finger RoHS compliance available • Wavelength 13/15: Tx Wavelength=1310nm Rx Wavelength=1550nm 15/13: Tx Wavelength=1550nm Rx Wavelength=1310nm • Communication protocol (1.25 Gbps) • +3.3 V SFF Transceiver F= FP Laser transceiver FDFB = DFB Laser transceiver • Single mode fiber • Connector options • Tx Output Power blank = -9 to -3 dBm 2 = -5 to 0 dBm 3 = -3 to +2 dBm 4 = 0 to +5 dBm • Operating Temperature blank = Commercial temperature (-5 to 70 ºC) A = Industrial temperature (-40 to 85 ºC) • Shielding Finger Option Blank = No shielding finger S = with Shielding finger • RoHS compliance available Blank = RoHS non-compliant product G5 = RoHS 5/6-compliant product (lead exemption) LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 9 LUMNDS796-Jan2407 Rev. A.3 1.25 Gbps bi-directional SC Receptacle Single Fiber Transceiver B-1X/1X-1250C-F(DFB)-SSCx Warnings: Handling Precautions: This device is susceptible to damage as a result of electrostatic discharge (ESD). A static free environment is highly recommended. Follow guidelines according to proper ESD procedures. Laser Safety: Radiation emitted by laser devices can be dangerous to human eyes. Avoid eye exposure to direct or indirect radiation. Legal Notes: IMPORTANT NOTICE! All information contained in this document is subject to change without notice, at LuminentOIC’s sole and absolute discretion. LuminentOIC warrants performance of its products to current specifications only in accordance with the company’s standard one-year warranty; however, specifications designated as “preliminary” are given to describe components only, and LuminentOIC expressly disclaims any and all warranties for said products, including express, implied, and statutory warranties, warranties of merchantability, fitness for a particular purpose, and non-infringement of proprietary rights. Please refer to the company’s Terms and Conditions of Sale for further warranty information. LuminentOIC assumes no liability for applications assistance, customer product design, software performance, or infringement of patents, services, or intellectual property described herein. No license, either express or implied, is granted under any patent right, copyright, or intellectual property right, and LuminentOIC makes no representations or warranties that the product(s) described herein are free from patent, copyright, or intellectual property rights. Products described in this document are NOT intended for use in implantation or other life support applications where malfunction may result in injury or death to persons. LuminentOIC customers using or selling products for use in such applications do so at their own risk and agree to fully defend and indemnify LuminentOIC for any damages resulting from such use or sale. THE INFORMATION CONTAINED IN THIS DOCUMENT IS PROVIDED ON AN “AS IS” BASIS. Customer agrees that LuminentOIC is not liable for any actual, consequential, exemplary, or other damages arising directly or indirectly from any use of the information contained in this document. Customer must contact LuminentOIC to obtain the latest version of this publication to verify, before placing any order, that the information contained herein is current. © LuminentOIC, Inc. 2003 All rights reserved LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 10 LUMNDS796-Jan2407 Rev. A.3