B-13-15-622-TPM-SST4A-60 数据手册
622 Mbps Bi-directional Single Fiber Transceiver
B-13/15-622-TPM(3)-SXX4(A)-60
Features • Coaxial single mode single fiber package with optional SC/FC/ST/MU connector • Wavelength Tx 1310 nm/Rx 1550 nm • SONET OC-12 SDH STM-4 Compliant • Single +5V/+3.3V Power Supply • PECL/LVPECL Differential Inputs and Outputs • Wave Solderable and Aqueous Washable • Class 1 Laser Int. Safety Standard IEC 825 Compliant • Uncooled Laser diode with MQW structure • Complies with Telcordia (Bellcore) GR-468-CORE • Optical Isolation > 30 dB • Cross talk < -33 dB • Optical Return Loss >14 dB
Absolute Maximum Rating Parameter Power Supply Voltage (5V) Power Supply Voltage (3.3V) Output Current Soldering Temperature Storage Temperature Symbol Vcc Vcc Iout Tstg Min. 0 0 0 -40 Max. 6 3.6 30 260 85 Unit V V mA ºC ºC 10 seconds on leads only Note B-13/15-622-TPM-SXX4(A)-60 B-13/15-622-TPM3-SXX4(A)-60
Recommended Operating Condition Parameter Power Supply Voltage (5V) Power Supply Voltage (3.3V) Operating Temperature1 Operating Temperature1 Data Rate Note 1 : Please refer to ordering information Symbol Vcc Vcc Topr Topr Min. 4.75 3.1 0 -40 Typ. 5 3.3 622 Max. 5.25 3.5 70 85 Unit V V ºC ºC Mbps
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
1
LUMNDS830-Jul2105 rev. A.1
622 Mbps Bi-directional Single Fiber Transceiver
B-13/15-622-TPM(3)-SXX4(A)-60
Transmitter Specifications Parameter Optical Optical Transmit Power Output Center Wavelength Output Spectrum Width Extinction Ratio Output Eye Optical Rise Time Optical Fall Time Optical Isolation Optical Return Loss Relative Intensity Noise Total Jitter RIN TJ tr tf Po λ ∆λ ER -3 1260 8.2 1310 +2 1360 2.5 dBm nm nm dB RMS(σ) Output power is coupled into a 9/125 µm single mode fiber Symbol Min Typical Max Unit Notes
Compliant with Bellcore GR-253-CORE and ITU recommendation G957 30 14 1.2 1.2 -120 0.55 ns ns dB dB dB/Hz ns Measured with 223-1 PRBS with 72 ones and 72 zeros. 10% to 90% Values 10% to 90% Values Tx: 1310 nm/ Rx: 1550 nm
Transmitter Specifications Parameter Electrical Power Supply Current Data Input Current-Low Data Input Current-High Differential Input Voltage Data Input Voltage-Low Data Input Voltage-High ICC IIL IIH VIH-VIL VIL-VCC VIH-VCC -350 300 -2.0 -1.1 180 350 -1.58 -0.74 mA µA µA mV V V These inputs are compatible with 10K, 10KH and 100K ECL and PECL inputs Maximum current is specified at Vcc= Maximum @ maximum temperature Symbol Min Typical Max Unit Notes
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
2
LUMNDS830-Jul2105 rev. A.1
622 Mbps Bi-directional Single Fiber Transceiver
B-13/15-622-TPM(3)-SXX4(A)-60
Receiver Specifications Parameter Optical Sensitivity Maximum Input Power Signal Detect-Asserted Signal Detect-Deasserted Signal Detect-Hysteresis Cross Talk Wavelength of Operation Pin Pa Pd -3 -40 1480 3.0 -28 -28 -33 1600 dBm dBm dBm dBm dB dB nm Measured on transition: low to high Measured on transition: high to low Measured with 223-1 PRBS with 72 ones and 72 zeros. (ITU-T recommendation G.958) Symbol Min Typical Max Unit Notes
Receiver Specifications Parameter Electrical Power Supply Current Data Output Voltage-Low Data Output Voltage-High Signal Detect Output Voltage-Low ICC VOL -Vcc VOH- Vcc VSDL-Vcc -1.9 -1.1 -1.9 -1.1 100 -1.6 -0.8 -1.6 -0.8 mA V V V V These outputs are compatible with 10K, 10KH and 100KECL and PECL outputs. The current excludes the output load current Symbol Min Typical Max Unit Notes
Signal Detect Output Voltage-High VSDH- Vcc
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
3
LUMNDS830-Jul2105 rev. A.1
622 Mbps Bi-directional Single Fiber Transceiver
B-13/15-622-TPM(3)-SXX4(A)-60
Connection Diagram
1. (Rx GND) 2. (Rx +) 3. (Rx-) 4. (SD) 5. (Rx Vcc) 6. (Tx Vcc) 7. (TD-) 8. (TD+) 9. (Tx GND)
NC
Top View
NC
Receiver Signal Ground Receiver Data Out Receiver Data Out Bar Signal Detect Receiver Power Supply Transmitter Power Supply Transmitter Data In Bar Transmitter Data in Transmitter Signal Ground
PIN 1 2 3 4 5 6 7 8 Warnings 9
Symbol RxGND RD+ RDSD RxVcc TxVcc TDTD+ TxGND
Notes Directly connect this pin to the receiver ground plane See recommended circuit schematic See recommended circuit schematic Active high on this indicates a received optical signal DC power for the receiver section DC power for the transmitter section See recommended circuit schematic See recommended circuit schematic Directly connect this pin to the transmitter ground plane
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
4
LUMNDS830-Jul2105 rev. A.1
622 Mbps Bi-directional Single Fiber Transceiver
B-13/15-622-TPM(3)-SXX4(A)-60
Recommended Circuit Schematic
Tx Vcc
C5
Rx Vcc
98
R1 R3
765
432
1
R9
R5
R7
C6
TD + TD -
RD + RD -
Tx Vcc Rx Vcc
R2 R4
SD
R10
No internal connection
Transceiver Top view
No internal connection
R6
R8
L1
Notes +3.3V: R1=R3=R5=R7=R9=130 R2=R4=R6=R8=R10=82 C1=C2=C3=C5=C6=0.1F C4=10F L1=L2=1H
Notes +5V: R1=R3=R5=R7=R9=82 R2=R4=R6=R8=R10=130 C1=C2=C3=C5=C6=0.1F C4=10F L1=L2=1H
Vcc
C3
L2
C4
C1
Rx Vcc
C2
Tx Vcc
The split-loaded terminations for ECL signals need to be located at the input of devices receiving those ECL signals. The power supply filtering is required for good EMI performance. Use short tracks from the inductor L1/L2 to the module Rx Vcc/ Tx Vcc A GND plane under the module is required for good EMI and sensitivity performance.
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
5
LUMNDS830-Jul2105 rev. A.1
622 Mbps Bi-directional Single Fiber Transceiver
B-13/15-622-TPM(3)-SXX4(A)-60
Package Diagram
Top View
max
Front View
Units: mm
Side View
Rear View
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
6
LUMNDS830-Jul2105 rev. A.1
622 Mbps Bi-directional Single Fiber Transceiver
B-13/15-622-TPM(3)-SXX4(A)-60
Ordering Information Available Options: B-13/15-622-TPM-SSC4(A)-60 B-13/15-622-TPM-SST4(A)-60 B-13/15-622-TPM-SFC4(A)-60 B-13/15-622-TPM-SMU4(A)-60 Part numbering Definition:
B-13/15-622-TPM3-SSC4(A)-60 B-13/15-622-TPM3-SST4(A)-60 B-13/15-622-TPM3-SFC4(A)-60 B-13/15-622-TPM3-SMU4(A)-60
B - 13/15 - 622 - TPM(3)
• Wavelength Tx Wavelength=1310nm Rx Wavelength=1550nm • Communication protocol (622 Mbps) • TPM = +5V Transceiver TPM3 = +3.3 V Transceiver • Single mode fiber • Connector options SC/FC/ST/MU • Tx Power range 4= -3 to +2 dBm • Temperature Blank = Commercial Temperature (0 to 70℃) A = Industrial Temperatuure (-40 to 85℃) • -60 : fiber length = 660mm ±20mm Warnings
- S XX
TxPower
Temperature -60
Handling Precautions: This device is susceptible to damage as a result of electrostatic discharge (ESD). A static free environment is highly recommended. Follow guidelines according to proper ESD procedures. Laser Safety: Radiation emitted by laser devices can be dangerous to human eyes. Avoid eye exposure to direct or indirect radiation.
Legal Notice
IMPORTANT NOTICE! All information contained in this document is subject to change without notice, at LuminentOIC’s sole and absolute discretion. LuminentOIC warrants performance of its products to current specifications only in accordance with the company’s standard one-year warranty; however, specifications designated as “preliminary” are given to describe components only, and LuminentOIC expressly disclaims any and all warranties for said products, including express, implied, and statutory warranties, warranties of merchantability, fitness for a particular purpose, and non-infringement of proprietary rights. Please refer to the company’s Terms and Conditions of Sale for further warranty information. LuminentOIC assumes no liability for applications assistance, customer product design, software performance, or infringement of patents, services, or intellectual property described herein. No license, either express or implied, is granted under any patent right, copyright, or intellectual property right, and LuminentOIC makes no representations or warranties that the product(s) described herein are free from patent, copyright, or intellectual property rights. Products described in this document are NOT intended for use in implantation or other life support applications where malfunction may result in injury or death to persons. LuminentOIC customers using or selling products for use in such applications do so at their own risk and agree to fully defend and indemnify LuminentOIC for any damages resulting from such use or sale. THE INFORMATION CONTAINED IN THIS DOCUMENT IS PROVIDED ON AN “AS IS” BASIS. Customer agrees that LuminentOIC is not liable for any actual, consequential, exemplary, or other damages arising directly or indirectly from any use of the information contained in this document. Customer must contact LuminentOIC to obtain the latest version of this publication to verify, before placing any order, that the information contained herein is current. © LuminentOIC, Inc. 2003 All rights reserved
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
7
LUMNDS830-Jul2105 rev. A.1