B-13-622-TDPM-SST4-60

622 Mbps Bi-directional Single Fiber Transceiver B-15/13-622-TDPM(3)-Sxx4-60 Features • Coaxial single mode single fiber package with optional SC/FC/ST connector • Wavelength Tx 1530 nm/ Rx 1310nm • SONET OC-12 SDH STM-4 • Single +5V/+3.3V Power Supply • PECL/LVPECL Differential Inputs and Outputs • Wave Solderable and Aqueous washable • Class 1 Laser Int. Safety Standad IEC 825 Compliant • Uncooled laser diode with MQW structure DFB Laser • Complies with Telcordia (Bellcore) GR-468-CORE • Temperature Range: 0 to 70ºC • Optical Isolation >30 dB • Cross Talk < -33 dB • Optical Return Loss > 14dB • RoHS compliance available Absolute Maximum Rating Parameter Power Supply Voltage (5V) Power Supply Voltage (3.3V) Output Current Soldering Temperature Operating Temperature Storage Temperature Symbol Vcc Vcc Iout - Min. 0 0 0 -40 Max. 6 3.6 30 260 70 85 Unit V V mA ºC ºC ºC Note B-15/13-622-TDPM-Sxx4-60 B-15/13-622-TDPM3-Sxx4-60 10 seconds on leads only Topr Tstg Recommended Operating Condition Parameter Power Supply Voltage (5V) Power Supply Voltage (3.3V) Operating Temperature (Case) Data Rate Transmitter Specifications Parameter Optical Optical Transmit Power Output center Wavelength Output Spectrum Width Side Mode Suppression Ratio Extinction Ratio Output Eye Optical Rise Time Optical Fall Time Optical Isolation Optical Return Loss Relative Intensity Noise Total Jitter tr tf - Symbol Vcc Vcc Topr - Min. 4.75 3.1 0 - Typ. 5 3.3 622 Max. 5.25 3.5 70 - Unit V V ºC Mbps Symbol Min Typical Max Unit Notes Output power is coupled into a 9/125 µm single mode fiber -20 dB, width CW, Po =5mW (0 to 70ºC) Po λ ∆λ Sr ER -3 1480 30 8.2 30 14 - 35 - +2 1580 1 1.2 1.2 -120 0.55 dBm nm nm dB dB ns ns dB dB dB/Hz ns Compliant with Bellcore TR-NWT-000253 and ITU recommendation G.957 10% to 90% Values 10% to 90% Values Tx:1530 nm/ Rx:1310 nm RIN TJ Measured with 223-1 PRBS with 72 ones and 72 zeros. LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 1 LUMNDS832-Jun1207 Rev A.1 622 Mbps Bi-directional Single Fiber Transceiver B-15/13-622-TDPM(3)-Sxx4-60 Transmitter Specifications Parameter Electrical Power Supply Current Data Input Current-Low Data Input Current-High Differential Input Voltage Data Input Voltage-Low Data Input Voltage-High ICC IIL IIH VIH-VIL VIL-VCC VIH-VCC -350 300 -2.0 -1.1 180 350 -1.58 -0.74 mA µA µA mV V V These inputs are compatible with 10K, 10KH and 100K ECL and PECL inputs Maximum current is specified at Vcc= Maximum @ maximum temperature Symbol Min Typical Max Unit Notes Receiver Specifications Parameter Optical Sensitivity Maximum Input Power Signal Detect-Asserted Signal Detect-Deasserted Signal Detect-Hysteresis Cross Talk Wavelength of Operation Pin Pa Pd -3 -40 1260 3.0 -28 -28 -33 1360 dBm dBm dBm dBm dB dB nm Measured on transition: low to high Measured on transition: high to low Measured with 223-1 PRBS, BER = 10-10 Symbol Min Typical Max Unit Notes Receiver Specifications Parameter Electrical Power Supply Current Data Output Voltage-Low Data Output Voltage-High Signal Detect Output Voltage-Low Signal Detect Output Voltage-High ICC VOL -Vcc VOH- Vcc VSDL-Vcc VSDH- Vcc -1.9 -1.1 -1.9 -1.1 100 -1.6 -0.8 -1.6 -0.8 mA V V V V These outputs are compatible with 10K, 10KH and 100KECL and PECL outputs The current excludes the output load current Symbol Min Typical Max Unit Note LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 2 LUMNDS832-Jun1207 Rev A.1 622 Mbps Bi-directional Single Fiber Transceiver B-15/13-622-TDPM(3)-Sxx4-60 Connection Diagram 1. (Rx GND) 2. (Rx +) 3. (Rx-) 4. (SD) 5. (Rx Vcc) 6. (Tx Vcc) 7. (TX-) 8. (TX+) 9. (Tx GND) NC Top View NC Receiver Signal Ground Receiver Data Out Receiver Data Out Bar Signal Detect Receiver Power Supply Transmitter Power Supply Transmitter Data In Bar Transmitter Data in Transmitter Signal Ground PIN 1 2 3 4 5 6 7 8 Warnings 9 Symbol RxGND RD+ RDSD RxVcc TxVcc TDTD+ TxGND Notes Directly connect this pin to the receiver ground plane See recommended circuit schematic See recommended circuit schematic Active high on this indicates a received optical signal DC power for the receiver section DC power for the transmitter section See recommended circuit schematic See recommended circuit schematic Directly connect this pin to the transmitter ground plane LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 3 LUMNDS832-Jun1207 Rev A.1 622 Mbps Bi-directional Single Fiber Transceiver B-15/13-622-TDPM(3)-Sxx4-60 Recommended Circuit Schematic Tx Vcc C5 Rx Vcc 98 R1 R3 765 432 1 R9 R5 R7 C6 TD + TD - RD + RD - Tx Vcc Rx Vcc R2 R4 SD R10 No internal connection Transceiver Top view No internal connection R6 R8 L1 Notes +3.3V: R1=R3=R5=R7=R9=130 R2=R4=R6=R8=R10=82 C1=C2=C3=C5=C6=0.1F C4=10F L1=L2=1H Notes +5V: R1=R3=R5=R7=R9=82 R2=R4=R6=R8=R10=130 C1=C2=C3=C5=C6=0.1F C4=10F L1=L2=1H Vcc C3 L2 C4 C1 Rx Vcc C2 Tx Vcc The split-loaded terminations for ECL signals need to be located at the input of devices receiving those ECL signals. The power supply filtering is required for good EMI performance. Use short tracks from the inductor L1/L2 to the module Rx Vcc. A GND plane under the module is required for good EMI and sensitivity performance. LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 4 LUMNDS832-Jun1207 Rev A.1 622 Mbps Bi-directional Single Fiber Transceiver B-15/13-622-TDPM(3)-Sxx4-60 Package Diagram Top View max Front View Units: mm Side View Rear View LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 5 LUMNDS832-Jun1207 Rev A.1 622 Mbps Bi-directional Single Fiber Transceiver B-15/13-622-TDPM(3)-Sxx4-60 Ordering Information Available Options:  B-15/13-622-TDPM-SSC4-60 B-15/13-622-TDPM-SST4-60 B-15/13-622-TDPM-SFC4-60 Part numbering Definition: B-15/13-622-TDPM3-SSC4-60 B-15/13-622-TDPM3-SST4-60 B-15/13-622-TDPM3-SFC4-60 B-15/13-622-TDPM-SSC4-60-G5 B-15/13-622-TDPM-SST4-60-G5 B-15/13-622-TDPM-SFC4-60-G5 B-15/13-622-TDPM3-SSC4-60-G5 B-15/13-622-TDPM3-SST4-60-G5 B-15/13-622-TDPM3-SFC4-60-G5 B - 15/13 - 622 - TDPM(3) - S xx 4 -60 • Wavelength Tx Wavelength=1530nm Rx Wavelength=1310nm • Communication protocol (622 Mbps) • TDPM = +5V Transceiver TDPM3 = +3.3 V Transceiver • Single mode fiber • Connector options SC/FC/ST • Tx Power range 4= -3 to +2 dBm • -60 : fiber length = 660mm ±20mm • RoHS Blank = RoHS non-compliant product G5 = RoHS 5/6-compliant product (lead exemption) Warnings -RoHS Handling Precautions: This device is susceptible to damage as a result of electrostatic discharge (ESD). A static free environment is highly recommended. Follow guidelines according to proper ESD procedures. Laser Safety: Radiation emitted by laser devices can be dangerous to human eyes. Avoid eye exposure to direct or indirect radiation. Legal Notice IMPORTANT NOTICE! All information contained in this document is subject to change without notice, at LuminentOIC’s sole and absolute discretion. LuminentOIC warrants performance of its products to current specifications only in accordance with the company’s standard one-year warranty; however, specifications designated as “preliminary” are given to describe components only, and LuminentOIC expressly disclaims any and all warranties for said products, including express, implied, and statutory warranties, warranties of merchantability, fitness for a particular purpose, and non-infringement of proprietary rights. Please refer to the company’s Terms and Conditions of Sale for further warranty information. LuminentOIC assumes no liability for applications assistance, customer product design, software performance, or infringement of patents, services, or intellectual property described herein. No license, either express or implied, is granted under any patent right, copyright, or intellectual property right, and LuminentOIC makes no representations or warranties that the product(s) described herein are free from patent, copyright, or intellectual property rights. Products described in this document are NOT intended for use in implantation or other life support applications where malfunction may result in injury or death to persons. LuminentOIC customers using or selling products for use in such applications do so at their own risk and agree to fully defend and indemnify LuminentOIC for any damages resulting from such use or sale. THE INFORMATION CONTAINED IN THIS DOCUMENT IS PROVIDED ON AN “AS IS” BASIS. Customer agrees that LuminentOIC is not liable for any actual, consequential, exemplary, or other damages arising directly or indirectly from any use of the information contained in this document. Customer must contact LuminentOIC to obtain the latest version of this publication to verify, before placing any order, that the information contained herein is current. © LuminentOIC, Inc. 2003 All rights reserved LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 6 LUMNDS832-Jun1207 Rev A.1