C-15-2500-TDFB3-SSC4

2.5 Gbps Single Mode Transceiver C-1X-2500(C)-TDFB(3)-SSCX Features • SC Duplex Single Mode Transceiver • Industry Standard 1x9 Footprint • Complies with SONET OC-48 STM-16 • Single +3.3V / +5V Power Supply • Operating Temperature Range 0℃ ~ +70℃ • CML Differential Data Inputs and Outputs • PECL/LVPECL Signal Detection Output [C-1X-2500-TDFB(3)-SSCX] • TTL/LVTTL Signal Detection Output [C-1X-2500C-TDFB(3)-SSCX] • Wave Solderable and Aqueous Washable • Uncooled laser diode with MQW structure • Complies with Telcordia (Bellcore) GR-468-CORE Applications • STM 16/ OC-48, 2.5 Gigabit Absolute Maximum Rating Parameter Power Supply Voltage Power Supply Voltage Output Current Soldering Temperature Operating Temperature Storage Temperature Symbol Vcc Vcc Iout - Min. 0 0 0 0 -40 Max. 3.6 6 30 260 70 85 Unit V V mA ºC ºC ºC Note C-1X-2500(C)-TDFB3-SSCX C-1X-2500(C)-TDFB-SSCX 10 seconds on leads only Topr Tstg Recommended Operating Condition Parameter Power Supply Voltage 1 Power Supply Voltage Data Rate Note1: Please refer to ordering information 1 Symbol Vcc Vcc Topr - Min. 3.1 4.75 0 - Typ. 3.3 5 2488.32 Max. 3.5 5.25 70 - Unit V V ºC Mbit/s Operating Temperature (Case) LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 1 LUMNDS797-Dec0904 rev. A.0 2.5 Gbps Single Mode Transceiver C-1X-2500(C)-TDFB(3)-SSCX Transmitter Specifications (Optical) Parameter Optical Transmit Power Optical Transmit Power Output center Wavelength Output center Wavelength Output Spectrum Width Side Mode Suppression Ratio Extinction Ratio Output Eye Relative Intensity Noise Total Jitter RIN TJ Symbol Po Po λ λ ∆λ SMSR ER Min -5 0 1280 1500 30 8.2 Typical 1310 1550 35 Max 0 +5 1355 1580 1 -120 0.18 Unit dBm dBm nm nm nm dB dB dB/Hz ns Measured with 223-1 PRBS with 72 ones and 72 zeros Notes C-1X-2500(C)-TDFB(3)-SSC2 C-1X-2500(C)-TDFB(3)-SSC4 C-13-2500(C)-TDFB(3)-SSCX C-15-2500(C)-TDFB(3)-SSCX -20 dB width CW, Po=5mW Compliant with ITU recommendation G.957 Transmitter Specifications (Electrical) Parameter Power Supply Current Data Input Current-Low Data Input Current-High Data Input Voltage Symbol ICC IIL IIH VIH-VIL Min -350 300 Typical Max 260 350 Unit mA µA µA mV Peak-peak, single ended, AC coupled Notes Maximum current is specified at Vcc= Maximum @ maximum temperature Receiver Specifications (Optical) Parameter Sensitivity2 Maximum Input Power Signal Detect-Asserted Signal Detect-Deasserted Signal Detect-Hysteresis Wavelength of Operation Reflectance Note 2: Measured with 223-1 PRBS, BER= 10-10 Receiver Specifications (Electrical) Parameter Power Supply Current Data output Voltage Signal Detect Output Voltage-Low Signal Detect Output Voltage-High Signal Detect Output Voltage-Low Signal Detect Output Voltage-High Symbol ICC VOH -VOL VSDL VSDH VSDL-Vcc VSDH- Vcc Min 300 2.0 -2.0 -1.1 Typical Max 100 900 0.5 -1.58 -0.74 Unit mA mV V V V V Note The current excludes the output load current Peak-peak, single-ended, AC-coupled C-1X-2500C-TDFB(3)-SSCX C-1X-2500-TDFB(3)-SSCX Symbol Pin Pa Pd Min 0 -38 1 1100 Typical Max -20 -20 1600 -27 Unit dBm dBm dBm dBm dB nm dB Measured on transition: low to high Measured on transition: high to low Notes LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 2 LUMNDS797-Dec0904 rev. A.0 2.5 Gbps Single Mode Transceiver C-1X-2500(C)-TDFB(3)-SSCX Connection Diagram 1. (Rx GND) 2. (Rx +) 3. (Rx-) 4. (SD) 5. (Rx Vcc) 6. (Tx Vcc) 7. (TX-) 8. (TX+) 9. (Tx GND) NC Top View NC Receiver Signal Ground Receiver Data Out Receiver Data Out Bar Signal Detect Receiver Power Supply Transmitter Power Supply Transmitter Data In Bar Transmitter Data in Transmitter Signal Ground PIN 1 2 3 4 5 6 7 8 Warnings 9 Symbol RxGND RD+ RDSD RxVcc TxVcc TDTD+ TxGND Notes Directly connect this pin to the receiver ground plane See recommended circuit schematic See recommended circuit schematic Active high on this indicates a received optical signal DC power for the receiver section DC power for the transmitter section See recommended circuit schematic See recommended circuit schematic Directly connect this pin to the transmitter ground plane LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 3 LUMNDS797-Dec0904 rev. A.0 2.5 Gbps Single Mode Transceiver C-1X-2500(C)-TDFB(3)-SSCX Recommended Circuit Schematic C-1X-2500-TDFB(3)-SSCX Rx Vcc 9 8 7 6 5 43 2 1 R1 C5 TD + TD - Z=50! Z=50! Z=50! Z=50! RD + RD SD Tx Vcc Rx Vcc No internal connection R2 Transceiver Top view No internal connection L1 Rx Vcc C1 Tx Vcc C2 Notes +3.3V: C1=C2=C5=0.1"F C3=C4=10"F L1=L2=1"H R1=130! R2=82! Notes +5V: C1=C2=C5=0.1"F C3=C4=10"F L1=L2=1"H R1=82! R2=130! Vcc C3 L2 C4 C-1X-2500C-TDFB(3)-SSCX 98 765 432 1 TD + TD - Z=50! Z=50! Z=50! Z=50! RD + RD SD Tx Vcc Rx Vcc No internal connection Transceiver Top view No internal connection Notes: C1=C2=0.1"F C3=C4=10"F L1=L2=1"H L1 Vcc Rx Vcc C1 Tx Vcc C2 C3 L2 C4 The split-loaded terminations for ECL signals need to be located at the input of devices receiving those ECL signals. The power supply filtering is required for good EMI performance. Use short tracks from the inductor L1/L2 to the module Rx Vcc. A GND plane under the module is required for good EMI and sensitivity performance. LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 4 LUMNDS797-Dec0904 rev. A.0 2.5 Gbps Single Mode Transceiver C-1X-2500(C)-TDFB(3)-SSCX Package Diagram Units in mm SC Transceiver Assembly 9.8mm Top View Front View Side View Rear View LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 5 LUMNDS797-Dec0904 rev. A.0 2.5 Gbps Single Mode Transceiver C-1X-2500(C)-TDFB(3)-SSCX Ordering Information Available Options:  C-13-2500-TDFB-SSC2 C-13-2500C-TDFB-SSC2 C-13-2500-TDFB3-SSC2 C-13-2500C-TDFB3-SSC2 C-15-2500-TDFB-SSC2 C-15-2500C-TDFB-SSC2 C-15-2500-TDFB3-SSC2 C-15-2500C-TDFB3-SSC2 Part numbering Definition: C-13-2500-TDFB-SSC4 C-13-2500C-TDFB-SSC4 C-13-2500-TDFB3-SSC4 C-13-2500C-TDFB3-SSC4 C-15-2500-TDFB-SSC4 C-15-2500C-TDFB-SSC4 C-15-2500-TDFB3-SSC4 C-15-2500C-TDFB3-SSC4 C - 1X - 2500(C) - TDFB(3) - S SC TxPower • 13 = Wavelength 1310nm 15 = Wavelength 1550nm • Communication protocol (2.5 Gbps) 2500 = PECL Signal Detection Output 2500C = TTL Signal Detection Output • TDFB = +5V Transceiver, DFB TDFB3= +3.3V Transceier, DFB • Single mode fiber • Connector options • Tx Power range 2 = -5 to 0 dBm 4 = 0 to +5 dBm Warnings: Handling Precautions: This device is susceptible to damage as a result of electrostatic discharge (ESD). A static free environment is highly recommended. Follow guidelines according to proper ESD procedures. Laser Safety: Radiation emitted by laser devices can be dangerous to human eyes. Avoid eye exposure to direct or indirect radiation. Legal Notes: IMPORTANT NOTICE! All information contained in this document is subject to change without notice, at LuminentOIC’s sole and absolute discretion. LuminentOIC warrants performance of its products to current specifications only in accordance with the company’s standard one-year warranty; however, specifications designated as “preliminary” are given to describe components only, and LuminentOIC expressly disclaims any and all warranties for said products, including express, implied, and statutory warranties, warranties of merchantability, fitness for a particular purpose, and non-infringement of proprietary rights. Please refer to the company’s Terms and Conditions of Sale for further warranty information. LuminentOIC assumes no liability for applications assistance, customer product design, software performance, or infringement of patents, services, or intellectual property described herein. No license, either express or implied, is granted under any patent right, copyright, or intellectual property right, and LuminentOIC makes no representations or warranties that the product(s) described herein are free from patent, copyright, or intellectual property rights. Products described in this document are NOT intended for use in implantation or other life support applications where malfunction may result in injury or death to persons. LuminentOIC customers using or selling products for use in such applications do so at their own risk and agree to fully defend and indemnify LuminentOIC for any damages resulting from such use or sale. THE INFORMATION CONTAINED IN THIS DOCUMENT IS PROVIDED ON AN “AS IS” BASIS. Customer agrees that LuminentOIC is not liable for any actual, consequential, exemplary, or other damages arising directly or indirectly from any use of the information contained in this document. Customer must contact LuminentOIC to obtain the latest version of this publication to verify, before placing any order, that the information contained herein is current. © LuminentOIC, Inc. 2003 All rights reserved LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 6 LUMNDS797-Dec0904 rev. A.0