C-157-622-TDFB3-SSC4

622 Mbps CWDM Single Mode Transceiver C-1xx-622-TDFB(3)-SSC4 Features • SC Duplex Single Mode Transceiver • Industry Standard 1x9 Footprint • Complies with IEEE 802.3 Gigabit Ethernet • Single +3.3V/5V Power Supply • Operating temperature Range 0 to 70ºC • PECL Differential Inputs and Outputs • PECL Signal Detection Output • Wave solderable and Aqueous Washable • Uncooled laser diode with MQW stucture • Complies with Telcordia (Bellcore) GR-468-CORE • 622 Mbps application • CWDM application • RoHS compliance available Absolute Maximum Rating Parameter Power Supply Voltage Power Supply Voltage Output Current Soldering Temperature Operating temerature Storage Temperature Symbol Vcc Vcc Iout - Min. 0 0 0 0 -40 Max. 6 3.6 30 260 70 85 Unit V V mA ºC ºC ºC Note C-1xx-622-TDFB-SSC4 C-1xx-622-TDFB3-SSC4 10 seconds on leads only Topr Tstg Recommended Operating Condition Parameter Power Supply Voltage Power Supply Voltage Operating Temperature (Case) Data Rate Symbol Vcc Vcc Topr Min. 4.75 3.1 0 Typ. 5 3.3 622 Max. 5.25 3.5 70 Unit V V ºC Mbps Transmitter Specifications Parameter Optical Optical Transmit Power Output center Wavelength Output Spectrum Width Side Mode Suppression Ratio Extinction Ratio Output Eye Optical Rise Time Optical Fall Time Relative Intensity Noise Total Jitter tr tf Symbol Min Typical Max Unit Notes Po λ ∆λ Sr ER -3 λ − 5.5 30 9 - λ 35 - +2 λ + 7.5 1 0.26 0.26 -120 0.27 dBm nm nm dB dB ns ns dB/Hz ns Output Power is coupled into a 9/125 µm single λ = 1xxx nm -20 dB width CW, Po= 5mW Compliant with IEEE 802.3 20% to 80% Values 20% to 80% Values RIN TJ Measured with 27-1 PRBS LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 1 LUMNDS1892-May1308 Rev A.0 622 Mbps CWDM Single Mode Transceiver C-1xx-622-TDFB(3)-SSC4 Transmitter Specifications Parameter Electrical Power Supply Current Data Input Current-Low Data Input Current-High Differential Input Voltage Data Input Voltage-Low Data Input Voltage-High ICC IIL IIH VIH-VIL VIL-VCC VIH-VCC -350 300 -2.0 -1.1 260 350 -1.58 -0.74 mA µA µA mV V V These inputs are compatible with 10K, 10KH and 100K ECL and PECL inputs Maximum current is specified at Vcc= Maximum @ maximum temperature Symbol Min Typical Max Unit Notes Receiver Specifications Parameter Optical Sensitivity Maximum Input Power Signal Detect-Asserted Signal Detect-Deasserted Signal Detect-Hysteresis Wavelength of Operation Pin Pa Pd Pa-Pd -3 -38 1 1100 -28 -28 1620 dBm dBm dBm dBm dB nm Measured on transition: low to high Measured on transition: high to low Measured with 27-1 PRBS,BER= 10-12 Symbol Min Typical Max Unit Notes Receiver Specifications Parameter Electrical Power Supply Current Data Output Voltage-Low Data Output Voltage-High Signal Detect Output Voltage-Low Signal Detect Output Voltage-High ICC VOL -Vcc VOH- Vcc VSDL-Vcc VSDH- Vcc -2.0 -1.1 -2.0 -1.1 100 -1.58 -0.74 -1.58 -0.74 mA V V V V The current excludes the output load current These outputs are compatible with 10K, 10KH and 100KECL and PECL outputs Symbol Min Typical Max Unit Note LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 2 LUMNDS1892-May1308 Rev A.0 622 Mbps CWDM Single Mode Transceiver C-1xx-622-TDFB(3)-SSC4 Connection Diagram 1. (Rx GND) 2. (Rx +) 3. (Rx-) 4. (SD) 5. (Rx Vcc) 6. (Tx Vcc) 7. (TX-) 8. (TX+) 9. (Tx GND) NC Top View NC Receiver Signal Ground Receiver Data Out Receiver Data Out Bar Signal Detect Receiver Power Supply Transmitter Power Supply Transmitter Data In Bar Transmitter Data in Transmitter Signal Ground PIN 1 2 3 4 5 6 7 8 Warnings 9 Symbol RxGND RD+ RDSD RxVcc TxVcc TDTD+ TxGND Notes Directly connect this pin to the receiver ground plane See recommended circuit schematic See recommended circuit schematic Active high on this indicates a received optical signal DC power for the receiver section DC power for the transmitter section See recommended circuit schematic See recommended circuit schematic Directly connect this pin to the transmitter ground plane LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 3 LUMNDS1892-May1308 Rev A.0 622 Mbps CWDM Single Mode Transceiver C-1xx-622-TDFB(3)-SSC4 Recommended Circuit Schematic C-1xx-622-TDFB(3)-SSC4 Tx Vcc C5 Rx Vcc 9 R1 R3 8 7 65 43 2 1 R9 R5 R7 C6 TD + TD - RD + RD - Tx Vcc Rx Vcc R2 R4 SD R10 R6 No internal connection Transceiver Top view No internal connection R8 L1 Vcc Notes +3.3V: R1=R3=R5=R7=R9=130 R2=R4=R6=R8=R10=82 C1=C2=C3=C5=C6=0.1F C4=10F L1=L2=1H Notes +5V: R1=R3=R5=R7=R9=82 R2=R4=R6=R8=R10=130 C1=C2=C3=C5=C6=0.1F C4=10F L1=L2=1H C3 C1 Rx Vcc L2 C4 C2 Tx Vcc The split-loaded terminations for ECL signals need to be located at the input of devices receiving those ECL signals. The power supply filtering is required for good EMI performance. Use short tracks from the inductor L1/L2 to the module Rx Vcc. A GND plane under the module is required for good EMI and sensitivity performance. LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 4 LUMNDS1892-May1308 Rev A.0 622 Mbps CWDM Single Mode Transceiver C-1xx-622-TDFB(3)-SSC4 Package Diagram Top View Front View Units: mm Side View Rear View LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 5 LUMNDS1892-May1308 Rev A.0 622 Mbps CWDM Single Mode Transceiver C-1xx-622-TDFB(3)-SSC4 Ordering Information Available Options:  C-1xx-622-TDFB-SSC4 C-1xx-622-TDFB3-SSC4 C-1xx-622-TDFB-SSC4-G5 C-1xx-622-TDFB3-SSC4-G5 Part numbering Definition: C - 1xx - 622 - TDFB(3) - S SC TxPower Temperature and Package RoHS • Tx Wavelength = 1xx0 nm xx=47,49,51,53,55,57,59,61 • Communication protocol (622 Mbps) 622 = PECL Signal Detection Output • TDFB = +5V Transceiver, DFB TDFB3= +3.3V Transceier, DFB • Single mode fiber • Connector options • Tx Power range 4 = -3 to +2 dBm • Temperature range and package Blank = commercial temperature(0 to 70 ºC), 10.4 mm, Black case • Ordering Information Blank = RoHS non-compliant product G5 = RoHS 5/6-compliant product (lead exemption) LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 6 LUMNDS1892-May1308 Rev A.0 1.25 Gbps CWDM Single Mode Transceiver C-1xx-622-TDFB(3)-SSC4 Warnings Handling Precautions: This device is susceptible to damage as a result of electrostatic discharge (ESD). A static free environment is highly recommended. Follow guidelines according to proper ESD procedures. Laser Safety: Radiation emitted by laser devices can be dangerous to human eyes. Avoid eye exposure to direct or indirect radiation. Legal Notice IMPORTANT NOTICE! All information contained in this document is subject to change without notice, at LuminentOIC’s sole and absolute discretion. LuminentOIC warrants performance of its products to current specifications only in accordance with the company’s standard one-year warranty; however, specifications designated as “preliminary” are given to describe components only, and LuminentOIC expressly disclaims any and all warranties for said products, including express, implied, and statutory warranties, warranties of merchantability, fitness for a particular purpose, and non-infringement of proprietary rights. Please refer to the company’s Terms and Conditions of Sale for further warranty information. LuminentOIC assumes no liability for applications assistance, customer product design, software performance, or infringement of patents, services, or intellectual property described herein. No license, either express or implied, is granted under any patent right, copyright, or intellectual property right, and LuminentOIC makes no representations or warranties that the product(s) described herein are free from patent, copyright, or intellectual property rights. Products described in this document are NOT intended for use in implantation or other life support applications where malfunction may result in injury or death to persons. LuminentOIC customers using or selling products for use in such applications do so at their own risk and agree to fully defend and indemnify LuminentOIC for any damages resulting from such use or sale. THE INFORMATION CONTAINED IN THIS DOCUMENT IS PROVIDED ON AN “AS IS” BASIS. Customer agrees that LuminentOIC is not liable for any actual, consequential, exemplary, or other damages arising directly or indirectly from any use of the information contained in this document. Customer must contact LuminentOIC to obtain the latest version of this publication to verify, before placing any order, that the information contained herein is current. © LuminentOIC, Inc. 2003 All rights reserved LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 7 LUMNDS1892-May1308 Rev A.0