FTM-5001C-SL80G

May 12, 2006 155Mbps SFP Transceiver with Spring Latch (For 15km～80km transmission) Members of FlexonTM Family Compatible with FCC 47 CFR Part 15, Class B Compatible with FDA 21 CFR 1040.10 and 1040.11, Class I Compliant with RoHS Description Fiberxon 155Mbps spring-latch SFP transceiver is Features Up to 155Mbps data-rate 1310nm FP laser and PIN photodetector for 15km and 40km transmission 1550nm uncooled DFB laser and PIN photodetector for 80km transmission Standard serial ID information Compatible with SFP MSA SFP MSA package with duplex LC connector With spring latch for easily removing Very low EMI and excellent ESD protection +3.3V single power supply Operating case temperature: Standard : 0 to +70℃ Industrial : -40 to +85℃ high performance, cost effective modules that supports data-rate of 155Mbps and transmission distance from 15km to 80km. The transceiver consists of two sections: The transmitter section incorporates a FP or uncooled DFB laser. And the receiver section consists of a PIN photodiode integrated with a trans-impedance preamplifier (TIA). All modules satisfy class I laser safety requirements. The optical output can be disabled by a TTL logic high-level input of Tx Disable. Tx Fault is provided to indicate degradation of the laser. Loss of signal (LOS) output is provided to indicate the loss of an input optical signal of receiver. The standard serial ID information Compatible with Applications SDH STM-1, S-1.1, L-1.1, L-1.2 SONET OC-3 IR1, LR1, LR2 Other optical links SFP MSA describes the transceiver’s capabilities, standard interfaces, manufacturer and other information. The host equipment can access this information via the two-wire serial CMOS EEPROM protocol. For further information, please refer to SFP Multi-Source Agreement (MSA). Standard Compatible with SFP MSA Compatible with ITU-T G.957 and G.958 Compatible with Telcordia GR-253-CORE Fiberxon Proprietary and Confidential, Do Not Copy or Distribute Controlled Electronic Version. 24hrs Obsolete when printed out without authorization. Page 1 of 11 Last printed 2006-05-15 10:28 155Mbps Spring Latch SFP Transceiver 15～80 km transmission May 12, 2006 Regulatory Compliance The transceivers have been tested according to American and European product safety and electromagnetic compatibility regulations (See Table 1). For further information regarding regulatory certification, please refer to Fiberxon regulatory specification and safety guidelines, or contact with Fiberxon, Inc. America sales office listed at the end of the documentation. Table 1 - Regulatory Compliance Feature Electrostatic Discharge (ESD) to the Electrical Pins Electrostatic Discharge (ESD) to the Duplex LC Receptacle Electromagnetic Interference (EMI) Immunity Laser Eye Safety Component Recognition Standard MIL-STD-883E Method 3015.7 IEC 61000-4-2 GR-1089-CORE FCC Part 15 Class B EN55022 Class B (CISPR 22B) VCCI Class B IEC 61000-4-3 FDA 21CFR 1040.10 and 1040.11 EN60950, EN (IEC) 60825-1,2 UL and CSA Compatible with standards Compatible with Class 1 laser product. TUV Certificate No. 50030043 UL file E223705 Compatible with standards Performance Class 1(>500 V) Compatible with standards Absolute Maximum Ratings Stress in excess of the maximum absolute ratings can cause permanent damage to the module. Table 2 - Absolute Maximum Ratings Parameter Storage Temperature Supply Voltage Operating Relative Humidity Symbol TS VCC Min. -40 -0.5 5 Max. +85 3.6 95 Unit °C V % Recommended Operating Conditions Table 3- Recommended Operating Conditions Parameter Operating Case Temperature Standard Industrial VCC ICC 155 Page 2 of 11 Last printed 2006-05-15 10:28 Symbol TC Min. 0 -40 3.13 Typical Max. +70 +85 Unit °C V mA Mbps Power Supply Voltage Power Supply Current Data Rate 3.3 3.47 300 Fiberxon Proprietary and Confidential, Do Not Copy or Distribute Controlled Electronic Version. 24hrs Obsolete when printed out without authorization. 155Mbps Spring Latch SFP Transceiver 15～80 km transmission May 12, 2006 FTM-3001C-SL15G, FTM-3001C-SL15iG (1310nm FP and PIN, 15km) Table 4 - Optical and Electrical Characteristics Parameter Centre Wavelength Average Output Power Spectral Width (RMS) Extinction Ratio Jitter Generation (RMS) Jitter Generation (pk-pk) Output Optical Eye Data Input Swing Differential Input Differential Impedance TX Disable TX Fault Disable Enable Fault Normal λC G.957 VIN ZIN 300 90 2.0 0 2.0 0 Receiver Centre Wavelength Receiver Sensitivity Receiver Overload Optical Path Penalty LOS De-Assert LOS Assert LOS Hysteresis Data Output Swing Differential LOS Notes: 1. 2. 3. 4. 5. 6. The optical power is launched into SMF. Measured with a PRBS 223-1 test pattern @155Mbps. PECL input, internally AC coupled and terminated. Measured with a PRBS 223-1 test pattern @155Mbps, BER ≤1×10-10. Measured with a PRBS 223-1 test pattern @155Mbps, over 15km G.652 SMF, BER ≤1×10-10. Internally AC coupled. High Low VOUT LOSD LOSA -45 1 370 2.0 0 4 1800 Vcc+0.3 0.8 -8 1 -37 1260 1580 -34 nm dBm dBm dB dBm dBm dB mV V V 6 4 4 5 100 1860 110 Vcc 0.8 Vcc+0.3 0.8 mV Ω V V V V Symbol λC P0ut σ EX 8.2 0.01 0.1 Min. Transmitter 1261 -15 1360 -8 4 nm dBm nm dB UI UI 2 3 1 Typical Max. Unit Notes Compatible with Telcordia GR-253-CORE and ITU-T Fiberxon Proprietary and Confidential, Do Not Copy or Distribute Controlled Electronic Version. 24hrs Obsolete when printed out without authorization. Page 3 of 11 Last printed 2006-05-15 10:28 155Mbps Spring Latch SFP Transceiver 15～80 km transmission May 12, 2006 FTM-3001C-SL40G, FTM-3001C-SL40iG (1310nm FP and PIN, 40km) Table 5 - Optical and Electrical Characteristics Parameter Centre Wavelength Average Output Power Spectral Width (RMS) Extinction Ratio Jitter Generation (RMS) Jitter Generation (pk-pk) Output Optical Eye Data Input Swing Differential Input Differential Impedance TX Disable TX Fault Disable Enable Fault Normal λC G.957 VIN ZIN 300 90 2.0 0 2.0 0 Receiver Centre Wavelength Receiver Sensitivity Receiver Overload Optical Path Penalty LOS De-Assert LOS Assert LOS Hysteresis Data Output Swing Differential LOS Notes: 1. The optical power is launched into SMF. 2. Measured with a PRBS 223-1 test pattern @155Mbps. 3. PECL input, internally AC coupled and terminated. 4. Measured with a PRBS 223-1 test pattern @155Mbps, extinction ratio ER=10dB, BER ≤1×10-10. 5. Measured with a PRBS 223-1 test pattern @155Mbps, over 40km G.652 SMF, BER ≤1×10-10. 6. Internally AC coupled. High Low VOUT LOSD LOSA -45 1 370 2.0 0 4 1800 Vcc+0.3 0.8 -8 1 -37 1260 1580 -34 nm dBm dBm dB dBm dBm dB mV V V 6 4 4 5 100 1860 110 Vcc 0.8 Vcc+0.3 0.8 mV Ω V V V V Symbol λC P0ut σ EX 10 0.01 0.1 Min. Transmitter 1263 -5 1360 0 3 nm dBm nm dB UI UI 2 3 1 Typical Max. Unit Notes Compatible with Telcordia GR-253-CORE and ITU-T Fiberxon Proprietary and Confidential, Do Not Copy or Distribute Controlled Electronic Version. 24hrs Obsolete when printed out without authorization. Page 4 of 11 Last printed 2006-05-15 10:28 155Mbps Spring Latch SFP Transceiver 15～80 km transmission May 12, 2006 FTM-5001C-SL80G (1550nm DFB and PIN, 80km) Table 6 - Optical and Electrical Characteristics Parameter Centre Wavelength Average Output Power Spectral Width (-20dB) Side Mode Suppression Ratio Extinction Ratio Jitter Generation (RMS) Jitter Generation (pk-pk) Output Optical Eye Data Input Swing Differential Input Differential Impedance TX Disable TX Fault Disable Enable Fault Normal λC G.957 VIN ZIN 300 90 2.0 0 2.0 0 Receiver Centre Wavelength Receiver Sensitivity Receiver Overload Optical Path Penalty LOS De-Assert LOS Assert LOS Hysteresis Data Output Swing Differential LOS Notes: 1. The optical power is launched into SMF. 2. Measured with a PRBS 223-1 test pattern @155Mbps. 3. PECL input, internally AC coupled and terminated. 4. Measured with a PRBS 223-1 test pattern @155Mbps, extinction ratio ER=10dB, BER ≤1×10-10. 5. Measured with a PRBS 223-1 test pattern @155Mbps, over 80km G.652 SMF, BER ≤1×10-10. 6. Internally AC coupled. High Low VOUT LOSD LOSA -45 1 370 2.0 0 4 1800 Vcc+0.3 0.8 -8 1 -37 1260 1580 -34 nm dBm dBm dB dBm dBm dB mV V V 6 4 4 5 100 1860 110 Vcc 0.8 Vcc+0.3 0.8 mV Ω V V V V Symbol λC P0ut ∆λ SMSR EX 30 10 0.01 0.1 Min. Transmitter 1480 -5 1580 0 1 nm dBm nm dB dB UI UI 2 3 1 Typical Max. Unit Notes Compatible with Telcordia GR-253-CORE and ITU-T Fiberxon Proprietary and Confidential, Do Not Copy or Distribute Controlled Electronic Version. 24hrs Obsolete when printed out without authorization. Page 5 of 11 Last printed 2006-05-15 10:28 155Mbps Spring Latch SFP Transceiver 15～80 km transmission May 12, 2006 EEPROM Information The SFP MSA defines a 256-byte memory map in EEPROM describing the transceiver’s capabilities, standard interfaces, manufacturer, and other information, which is accessible over a two-wire serial interface at the 8-bit address 1010000X (A0h). For memory contents please refer to Table 7. Table 7 - EEPROM Serial ID Memory Contents (A0h) Addr. 0 1 2 3—10 11 12 13 14 15 16 17 18 19 20—35 36 37—39 40—55 56—59 60—62 63 64—65 66 67 68—83 84—91 92—94 95 96—255 Field Size (Bytes) 1 1 1 8 1 1 1 1 1 1 1 1 1 16 1 3 16 4 3 1 2 1 1 16 8 3 1 160 Name of Field Identifier Ext. Identifier Connector Transceiver Encoding BR, nominal Reserved 03 04 07 00 00 xx 00 00 00 00 00 03 01 00 15km/40km/80km(0F/28/50) 15km/40km/80km(96/FF/FF) Hex Description SFP MOD4 LC OC 3, Single mode inter. or long reach NRZ 155Mbps Length (9um)-km xx Length (9um) xx Length (50um) 00 Length (62.5um) 00 Length (copper) 00 Reserved Vendor name Reserved Vendor OUI Vendor PN Vendor rev Reserved CC BASE Options BR, max BR, min Vendor SN 00 46 49 42 45 52 58 4F 4E 20 49 4E 43 2E 20 20 20 00 00 00 00 46 54 4D 2D xx 30 30 31 43 2D 53 4C xx xx xx 47 xx xx 00 00 00 00 00 xx 00 1A 00 00 xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx 00 00 00 xx “FIBERXON INC. “(ASCⅡ) “FTM-x001C-SLxx(i)G” (ASCⅡ) ASCⅡ( “31 30 00 00” means 1.0 revision) Check sum of bytes 0 - 62 LOS, TX_FAULT and TX_DISABLE ASCⅡ. Year (2 bytes, Month (2 bytes), Day (2 bytes) Check sum of bytes 64 - 94 Vendor date codexx xx xx xx xx xx 20 20 Reserved CC EXT Vendor specific Note: The “xx” byte should be filled in according to practical case. For more information, please refer to the related document of SFP Multi-Source Agreement (MSA). Fiberxon Proprietary and Confidential, Do Not Copy or Distribute Controlled Electronic Version. 24hrs Obsolete when printed out without authorization. Page 6 of 11 Last printed 2006-05-15 10:28 155Mbps Spring Latch SFP Transceiver 15～80 km transmission May 12, 2006 Recommended Host Board Power Supply Circuit Figure 1 shows the recommended host board power supply circuit. Figure 1, Recommended Host Board Power Supply Circuit Recommended Interface Circuit Figure 2 shows the recommended interface circuit. Host Board Vcc (+3.3V) 2×4.7K to 10K TX Disable TX Fault SerDat Out + SFP Module VccT 10K Z=50 TD + SerDat Out - Z=50 TD - Laser driver Protocol IC SERDES IC SerDat In + Z=50 RD + SerDat In - Z=50 Amplifier RD - LOS Vcc (+3.3V) 3×4.7K to 10K MOD-DEF2 MOD-DEF1 MOD-DEF0 EEPROM RGND Figure 2, Recommended Interface Circuit Pin Definitions Figure 3 below shows the pin numbering of SFP electrical interface. The pin functions are described in Table 8 with some accompanying notes. Fiberxon Proprietary and Confidential, Do Not Copy or Distribute Controlled Electronic Version. 24hrs Obsolete when printed out without authorization. Page 7 of 11 Last printed 2006-05-15 10:28 155Mbps Spring Latch SFP Transceiver 15～80 km transmission May 12, 2006 P in 2 0 T O P V IE W OF BOARD P in 1 1 P in 1 0 B O T T O M V IE W OF BOARD P in 1 Figure 3, Pin View Table 8– Pin Function Definitions Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Notes: 1. TX Fault is an open collector output, which should be pulled up with a 4.7k~10kΩ resistor on the host board to a voltage between 2.0V and Vcc+0.3V. Logic 0 indicates normal operation; logic 1 indicates a laser fault of some kind. In the low state, the output will be pulled to less than 0.8V. 2. TX Disable is an input that is used to shut down the transmitter optical output. It is pulled up within the module with a 4.7k~10kΩ resistor. Its states are: Low (0~0.8V): Transmitter on Page 8 of 11 Last printed 2006-05-15 10:28 Name VeeT TX Fault TX Disable MOD-DEF2 MOD-DEF1 MOD-DEF0 Rate Select LOS VeeR VeeR VeeR RDRD+ VeeR VccR VccT VeeT TD+ TDVeeT Function Transmitter Ground Transmitter Fault Indication Transmitter Disable Module Definition 2 Module Definition 1 Module Definition 0 Not Connected Loss of Signal Receiver Ground Receiver Ground Receiver Ground Inv. Received Data Out Received Data Out Receiver Ground Receiver Power Transmitter Power Transmitter Ground Transmit Data In Inv. Transmit Data In Transmitter Ground Plug Seq. 1 3 3 3 3 3 3 3 1 1 1 3 3 1 2 2 1 3 3 1 Note 6 Note 6 Note 5 Note 5 Note 4 Note 1 Note 2 Note 3 Note 3 Note 3 Notes Fiberxon Proprietary and Confidential, Do Not Copy or Distribute Controlled Electronic Version. 24hrs Obsolete when printed out without authorization. 155Mbps Spring Latch SFP Transceiver 15～80 km transmission May 12, 2006 (>0.8V,