MBM29LV400BC-90PCV

FUJITSU SEMICONDUCTOR DATA SHEET DS05-20862-8E FLASH MEMORY CMOS 4M (512K × 8/256K × 16) BIT MBM29LV400TC/BC-55/70/90 s FEATURES • Single 3.0 V read, program, and erase Minimizes system level power requirements • Compatible with JEDEC-standard commands Uses same software commands as E2PROMs • Compatible with JEDEC-standard world-wide pinouts 48-pin TSOP(1) (Package suffix: PFTN – Normal Bend Type, PFTR – Reversed Bend Type) 44-pin SOP (Package suffix: PF) 48-pin CSOP (Package suffix: PCV) 48-ball FBGA (Package suffix: PBT) 48-ball SCSP (Package suffix: PW) • Minimum 100,000 program/erase cycles • High performance 55 ns maximum access time • Sector erase architecture One 8K word, two 4K words, one 16K word, and seven 32K words sectors in word mode One 16K byte, two 8K bytes, one 32K byte, and seven 64K bytes sectors in byte mode Any combination of sectors can be concurrently erased. Also supports full chip erase • Boot Code Sector Architecture T = Top sector B = Bottom sector (Continued) s PRODUCT LINE UP Part No. Power Supply Voltage (V) Max Address Access Time (ns) Max CE Access Time (ns) Max OE Access Time (ns) MBM29LV400 TC/BC -55 V VCC = 3.3 V +0.3 V –0.3 -70 VCC = 3.0 V 70 70 30 +0.6 V –0.3 V -90 55 55 30 90 90 35 MBM29LV400TC-55/70/90/MBM29LV400BC-55/70/90 (Continued) • Embedded EraseTM* Algorithms Automatically preprograms and erases the chip or any sector • Embedded ProgramTM* Algorithms Automatically writes and verifies data at specified address • Data Polling and Toggle Bit feature for detection of program or erase cycle completion • Ready/Busy output (RY/BY) Hardware method for detection of program or erase cycle completion • Automatic sleep mode When addresses remain stable, automatically switch themselves to low power mode • Low VCC write inhibit ≤ 2.5 V • Erase Suspend/Resume Suspends the erase operation to allow a read in another sector within the same device • Sector protection Hardware method disables any combination of sectors from program or erase operations • Sector Protection set function by Extended sector Protect command • Fast Programming Function by Extended Command • Temporary sector unprotection Temporary sector unprotection via the RESET pin *: Embedded EraseTM and Embedded ProgramTM are trademarks of Advanced Micro Devices, Inc. s PACKAGES 48-pin plastic TSOP (1) Marking Side 48-pin plastic TSOP (1) 44-pin plastic SOP Marking Side Marking Side (FPT-48P-M19) 48-pin plastic CSOP (FPT-48P-M20) 48-pin plastic FBGA (FPT-44P-M16) 48-pin plastic SCSP (LCC-48P-M03) (BGA-48P-M11) (WLP-48P-M02) 2 MBM29LV400TC-55/70/90/MBM29LV400BC-55/70/90 s GENERAL DESCRIPTION The MBM29LV400TC/BC are a 4M-bit, 3.0 V-only Flash memory organized as 512K bytes of 8 bits each or 256K words of 16 bits each. The MBM29LV400TC/BC are offered in a 48-pin TSOP(1), 44-pin SOP 48-pin CSOP , , and 48-ball FBGA packages. These devices are designed to be programmed in-system with the standard system 3.0 V VCC supply. 12.0 V VPP and 5.0 V VCC are not required for write or erase operations. The devices can also be reprogrammed in standard EPROM programmers. The standard MBM29LV400TC/BC offer access times 70 ns and 120 ns, allowing operation of high-speed microprocessors without wait states. To eliminate bus contention the devices have separate chip enable (CE), write enable (WE), and output enable (OE) controls. The MBM29LV400TC/BC are pin and command set compatible with JEDEC standard E2PROMs. Commands are written to the command register using standard microprocessor write timings. Register contents serve as input to an internal state-machine which controls the erase and programming circuitry. Write cycles also internally latch addresses and data needed for the programming and erase operations. Reading data out of the devices is similar to reading from 5.0 V and 12.0 V Flash or EPROM devices. The MBM29LV400TC/BC are programmed by executing the program command sequence. This will invoke the Embedded Program Algorithm which is an internal algorithm that automatically times the program pulse widths and verifies proper cell margin. Typically, each sector can be programmed and verified in about 0.5 seconds. Erase is accomplished by executing the erase command sequence. This will invoke the Embedded Erase Algorithm which is an internal algorithm that automatically preprograms the array if it is not already programmed before executing the erase operation. During erase, the devices automatically time the erase pulse widths and verify proper cell margin. A sector is typically erased and verified in 1.0 second. (If already completely preprogrammed.) The devices also feature a sector erase architecture. The sector mode allows each sector to be erased and reprogrammed without affecting other sectors. The MBM29LV400TC/BC are erased when shipped from the factory. The devices feature single 3.0 V power supply operation for both read and write functions. Internally generated and regulated voltages are provided for the program and erase operations. A low VCC detector automatically inhibits write operations on the loss of power. The end of program or erase is detected by Data Polling of DQ7, by the Toggle Bit feature on DQ6, or the RY/BY output pin. Once the end of a program or erase cycle has been completed, the devices internally reset to the read mode. Fujitsu’s Flash technology combines years of EPROM and E2PROM experience to produce the highest levels of quality, reliability, and cost effectiveness. The MBM29LV400TC/BC memories electrically erase the entire chip or all bits within a sector simultaneously via Fowler-Nordhiem tunneling. The bytes/words are programmed one byte/word at a time using the EPROM programming mechanism of hot electron injection. 3 MBM29LV400TC-55/70/90/MBM29LV400BC-55/70/90 s PIN ASSIGNMENTS TSOP(1) A15 A14 A13 A12 A11 A10 A9 A8 N.C. N.C. WE RESET N.C. N.C. RY/BY N.C. A17 A7 A6 A5 A4 A3 A2 A1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 (Marking Side) 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 A16 BYTE VSS DQ 15/A-1 DQ7 DQ14 DQ6 DQ13 DQ5 DQ12 DQ4 VCC DQ11 DQ3 DQ10 DQ2 DQ9 DQ1 DQ8 DQ0 OE VSS CE A0 N.C. RY/BY A17 A7 A6 A5 A4 A3 A2 A1 A0 CE VSS OE 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 A0 CE VSS OE DQ0 DQ8 DQ1 DQ9 DQ2 DQ10 DQ3 DQ11 VCC DQ4 DQ12 DQ5 DQ13 DQ6 DQ14 DQ7 DQ15/A-1 VSS BYTE A16 DQ0 DQ8 DQ1 DQ9 DQ2 DQ10 DQ3 DQ11 1 2 3 4 5 6 7 8 9 SOP (Top View) 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 RESET WE A8 A9 A10 A11 A12 A13 A14 A15 A16 BYTE V SS DQ 15/A-1 DQ 7 DQ 14 DQ 6 DQ 13 DQ5 DQ 12 DQ4 VCC MBM29LV400TC/MBM29LV400BC Normal Bend 10 11 12 13 14 15 16 17 18 19 20 21 22 FPT-48P-M19 A1 A2 A3 A4 A5 A6 A7 A17 N.C. RY/BY N.C. N.C. RESET WE N.C. N.C. A8 A9 A10 A11 A12 A13 A14 A15 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 (Marking Side) MBM29LV400TC/MBM29LV400BC Reverse Bend FPT-44P-M16 FPT-48P-M20 (Continued) 4 MBM29LV400TC-55/70/90/MBM29LV400BC-55/70/90 (TOP VIEW) A1 A2 A3 A4 A5 A6 A7 A17 N.C. RY/BY N.C. N.C. RESET WE N.C. N.C. A8 A9 A10 A11 A12 A13 A14 A15 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 A0 CE VSS OE DQ0 DQ8 DQ1 DQ9 DQ2 DQ10 DQ3 DQ11 VCC DQ4 DQ12 DQ5 DQ13 DQ6 DQ14 DQ7 DQ15/A-1 VSS BYTE A16 CSOP-48 LCC-48P-M03 FBGA (Top View) Marking side A6 A13 A5 A9 A4 B6 A12 B5 A8 B4 C6 A14 C5 A10 C4 D6 A15 D5 A11 D4 N.C D3 N.C D2 A5 D1 A1 E6 A16 E5 F6 G6 H6 BYTE DQ15/A-1 VSS F5 G5 H5 DQ7 DQ14 DQ13 DQ6 E4 DQ5 E4 F4 DQ12 F3 G4 VCC G3 H4 DQ4 H3 WE RESET N.C A3 B3 C3 N.C C2 A6 C1 A2 RY/BY N.C A2 A7 A1 A3 B2 A17 B1 A4 DQ2 DQ10 E2 DQ0 E1 A0 F2 DQ8 F1 CE DQ11 DQ3 G2 DQ9 G1 OE H2 DQ1 H1 VSS BGA-48P-M11 (Continued) 5 MBM29LV400TC-55/70/90/MBM29LV400BC-55/70/90 (Continued) SCSP (Top View) Marking side A6 A3 A5 A7 A4 B6 A4 B5 A17 B4 C6 A2 C5 A6 C4 N.C C3 D6 A1 D5 A5 D4 N.C D3 N.C D2 A11 D1 A15 E6 A0 E5 DQ0 E4 DQ2 E3 F6 CE F5 DQ8 F4 G6 OE G5 H6 VSS H5 DQ9 DQ1 G4 H4 RY/BY N.C A3 B3 DQ10 DQ11 DQ3 F3 G3 H3 DQ4 H2 WE RESET N.C A2 A9 A1 A13 B2 A8 B1 A12 C2 A10 C1 A14 DQ5 DQ12 VCC E2 F2 G2 DQ7 DQ14 DQ13 DQ6 E1 A16 F1 G1 H1 BYTE DQ15/A-1 VSS WLP-48P-M02 6 MBM29LV400TC-55/70/90/MBM29LV400BC-55/70/90 s PIN DESCRIPTIONS Pin A17 to A0, A-1 DQ15 to DQ0 CE OE WE RY/BY RESET BYTE N.C. VSS VCC Address Inputs Data Inputs/Outputs Chip Enable Output Enable Write Enable Ready/Busy Output Hardware Reset Pin/Temporary Sector Unprotection Selects 8-bit or 16-bit mode No Internal Connection Device Ground Device Power Supply Function s LOGIC SYMBOL A-1 18 A17 to A0 DQ 15 to DQ 0 CE OE WE RESET BYTE RY/BY 16 or 8 7 MBM29LV400TC-55/70/90/MBM29LV400BC-55/70/90 s BLOCK DIAGRAM RY/BY Buffer VCC VSS DQ15 to DQ0 RY/BY Erase Voltage Generator Input/Output Buffers WE BYTE RESET State Control Command Register Program Voltage Generator CE OE Chip Enable Output Enable Logic STB Data Latch STB Y-Decoder Y-Gating Low VCC Detector Timer for Program/Erase Address Latch X-Decoder Cell Matrix A17 to A0 A-1 8 MBM29LV400TC-55/70/90/MBM29LV400BC-55/70/90 s DEVICE BUS OPERATIONS MBM29LV400TC/400BC User Bus Operations Table (BYTE = VIH) A0 A1 A6 A9 DQ0 to DQ15 Operation CE OE WE Auto-Select Manufacturer Code * Auto-Select Device Code * Read * 3 1 1 RESET H H H H H H H H VID L L L L H L L L L L X H H VID L X X H H H X H L L H A0 X X A0 L L L A1 X X A1 H H X X L L A6 X X A6 L L X X VID VID A9 X X A9 VID VID X X Code Code DOUT High-Z High-Z DIN X Code X High-Z Standby Output Disable Write (Program/Erase) Enable Sector Protection * * Verify Sector Protection * * Reset (Hardware)/Standby Legend: L = VIL, H = VIH, X = VIL or VIH, 2, 4 2, 4 L L X X H X X L X X Temporary Sector Unprotection*5 = Pulse input. See “sDC CHARACTERISTICS” for voltage levels. *1: Manufacturer and device codes are accessed via a command register write sequence. See “MBM29LV400TC/ 400BC Standard Command Definitions Table” in sDEVICE BUS OPERATIONS. *2: Refer to “7. Sector Protection” in sFUNCTIONAL DESCRIPTION. *3: WE can be VIL if OE is VIL, OE at VIH initiates the write operations. *4: VCC = 3.3 V ± 10% *5: Also used for the extended sector protection. MBM29LV400TC/400BC User Bus Operations (BYTE = VIL) 15 OE WE DQ-1 / A0 A1 A6 A9 CE A L L L H L L L L 5 Operation DQ0 to DQ7 RESET Code Code DOUT High-Z High-Z DIN X Code X High-Z H H H H H H H H VID L Auto-Select Manufacturer Code *1 Auto-Select Device Code *1 Read *3 Standby Output Disable Write (Program/Erase) Enable Sector Protection *2, *4 Verify Sector Protection *2, *4 Temporary Sector Unprotection * Reset (Hardware)/Standby Legend: L = VIL, H = VIH, X = VIL or VIH, L L L X H H VID L X X H H H X H L L L A-1 X X A-1 L L H A0 X X A0 L L X X L L A1 X X A1 H H X X L L A6 X X A6 L L X X VID VID A9 X X A9 VID VID X X H X X L X X X X = Pulse input. See “sDC CHARACTERISTICS” for voltage levels. *1: Manufacturer and device codes are accessed via a command register write sequence. See “MBM29LV400TC/ 400BC Standard Command Definitions Table” in sDEVICE BUS OPERATIONS. *2: Refer to “7. Sector Protection” in sFUNCTIONAL DESCRIPTION. *3: WE can be VIL if OE is VIL, OE at VIH initiates the write operations. *4: VCC = 3.3 V ± 10% *5: Also used for the extended sector protection. 9 MBM29LV400TC-55/70/90/MBM29LV400BC-55/70/90 MBM29LV400TC/400BC Standard Command Definitions First Bus Second Bus Third Bus Fourth Bus Fifth Bus Sixth Bus Write Cycle Write Cycle Write Cycle Read/Write Write Cycle Write Cycle Cycle Addr. Data Addr. Data Addr. Data Addr. Data Addr. Data Addr. Data XXXh 555h AAAh 555h AAAh 555h AAAh 555h AAAh 555h AAAh F0h AAh AAh AAh AAh AAh — 2AAh 555h 2AAh 555h 2AAh 555h 2AAh 555h 2AAh 555h — 55h 55h 55h 55h 55h — 555h AAAh 555h AAAh 555h AAAh 555h AAAh 555h AAAh — F0h 90h A0h 80h 80h — RA — PA 555h AAAh 555h AAAh — RD — PD AAh AAh — — — — 2AAh 555h 2AAh 555h — — — — 55h 55h — — — — 555h AAAh SA — — — — 10h 30h Command Sequence Word Read/Reset Bus Write Cycles Req’d Byte Word Read/Reset 1 3 3 4 6 6 Byte Word Autoselect Byte Word Program Byte Word Chip Erase Byte Word Sector Erase Byte Sector Erase Suspend Sector Erase Resume Erase can be suspended during sector erase with Addr. (“H” or “L”). Data (B0h) Erase can be resumed after suspend with Addr. (“H” or “L”). Data (30h) Notes: • Address bits A11 to A17 = X = “H” or “L” for all address commands except or Program Address (PA) and Sector Address (SA) • Bus operations are defined in “MBM29LV400TC/400BC User Bus Operations Tables (BYTE = VIH and BYTE = VIH)” in sDEVICE BUS OPERATIONS. • RA = Address of the memory location to be read PA = Address of the memory location to be programmed Addresses are latched on the falling edge of the WE pulse. SA = Address of the sector to be erased. The combination of A17, A16, A15, A14, A13, and A12 will uniquely select any sector. • RD = Data read from location RA during read operation. PD = Data to be programmed at location PA. Data is latched on the rising edge of WE. • The system should generate the following address patterns: Word Mode: 555h or 2AAh to addresses A0 to A10 Byte Mode: AAAh or 555h to addresses A–1 and A0 to A10 • Both Read/Reset commands are functionally equivalent, resetting the device to the read mode. • The command combinations not described in “MBM29LV400TC/400BC Standard Command Definitions Table” and “MBM29LV400TC/BC Extended Command Definitions Table” in sDEVICE BUS OPERATIONS are illegal. 10 MBM29LV400TC-55/70/90/MBM29LV400BC-55/70/90 MBM29LV400TC/BC Extended Command Definitions Bus First Bus Second Bus Third Bus Write Write Cycle Write Cycle Write Cycle Cycles Addr Data Addr Data Addr Data Req'd Word Byte Word Byte Word 2 Byte Word XXXh 3 2 555h AAAh XXXh XXXh XXXh 90h XXXh AAh A0h 2AAh 555h PA XXXh F0h *3 — — — — 55h PD 555h AAAh — 20h — Command Sequence Set to Fast Mode Fast Program *1 Reset from Fast Mode *1 Extended Sector Protect *2 Fourth Bus Read Cycle Addr — — Data — — 4 XXXh 60h SPA 60h SPA 40h SPA SD Byte SPA : Sector address to be protected. Set sector address (SA) and (A6, A1, A0) = (0, 1, 0). SD : Sector protection verify data. Output 01h at protected sector addresses and output 00h at unprotected sector addresses. *1: This command is valid while Fast Mode. *2: This command is valid while RESET= VID. *3: This data “00h” is also acceptable. MBM29LV400TC/400BC Sector Protection Verify Autoselect Codes A6 A1 A0 Type A12 to A17 A-1*1 Manufacture’s Code MBM29LV400TC Device Code MBM29LV400BC Sector Protection Byte Word Byte Word X X X Sector Addresses VIL VIL VIL VIL VIL VIL VIL VIH VIL VIH VIH VIL VIL VIL X VIL X VIL Code (HEX) 04h B9h 22B9h BAh 22BAh 01h*2 *1: A-1 is for Byte mode. In byte mode, DQ8 to DQ14 become “High-Z” and DQ15 becomes the lower address A-1. *2: Outputs 01h at protected sector addresses and outputs 00h at unprotected sector addresses. Extended Autoselect Code Table Type Manufacturer’s Code Code DQ15 DQ14 DQ13 DQ12 DQ11 DQ10 DQ9 DQ8 DQ7 DQ6 DQ5 DQ4 DQ3 DQ2 DQ1 DQ0 04h A-1/0 0 0 0 0 0 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 0 0 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 0 0 1 1 1 1 0 0 1 1 1 1 0 1 0 0 0 0 0 0 0 0 1 1 0 0 1 1 0 0 1 MBM29 (B)* B9h A-1 LV400TC (W) 22B9h 0 Device Code MBM29 (B)* BAh A-1 LV400BC (W) 22BAh 0 HI-Z HI-Z HI-Z HI-Z HI-Z HI-Z HI-Z HI-Z HI-Z HI-Z HI-Z HI-Z HI-Z HI-Z Sector Protection (B): Byte mode (W): Word mode HI-Z : High-Z 01h A-1/0 * : At Byte mode, DQ8 to DQ14 are High-Z and DQ15 is A-1, the lowest address. 11 MBM29LV400TC-55/70/90/MBM29LV400BC-55/70/90 s FLEXIBLE SECTOR-ERASE ARCHITECTURE • One 16K byte, two 8K bytes, one 32K byte, and seven 64K bytes. • Individual-sector, multiple-sector, or bulk-erase capability. • Individual or multiple-sector protection is user definable. (×8) 7FFFFh 16K byte 7BFFFh 8K byte 79FFFh 8K byte 77FFFh 32K byte 6FFFFh 64K byte 5FFFFh 64K byte 4FFFFh 64K byte 3FFFFh 64K byte 2FFFFh 64K byte 1FFFFh 64K byte 0FFFFh 64K byte 00000h (×16) 3FFFFh 64K byte 3DFFFh 64K byte 3CFFFh 64K byte 3BFFFh 64K byte 37FFFh 64K byte 2FFFFh 64K byte 27FFFh 64K byte 1FFFFh 32K byte 17FFFh 8K byte 0FFFFh 8K byte 07FFFh 16K byte 00000h (×8) 7FFFFh 6FFFFh 5FFFFh 4FFFFh 3FFFFh 2FFFFh 1FFFFh 0FFFFh 07FFFh 05FFFh 03FFFh 00000h (×16) 3FFFFh 37FFFh 2FFFFh 27FFFh 1FFFFh 17FFFh 0FFFFh 07FFFh 03FFFh 02FFFh 01FFFh 00000h MBM29LV400TC Sector Architecture MBM29LV400BC Sector Architecture 12 MBM29LV400TC-55/70/90/MBM29LV400BC-55/70/90 Sector Address Tables (MBM29LV400TC) Sector Address SA0 SA1 SA2 SA3 SA4 SA5 SA6 SA7 SA8 SA9 SA10 A17 0 0 0 0 1 1 1 1 1 1 1 A16 0 0 1 1 0 0 1 1 1 1 1 A15 0 1 0 1 0 1 0 1 1 1 1 A14 X X X X X X X 0 1 1 1 A13 X X X X X X X X 0 0 1 A12 X X X X X X X X 0 1 X Address Range (×8) 00000h to 0FFFFh 10000h to 1FFFFh 20000h to 2FFFFh 30000h to 3FFFFh 40000h to 4FFFFh 50000h to 5FFFFh 60000h to 6FFFFh 70000h to 77FFFh 78000h to 79FFFh 7A000h to 7BFFFh 7C000h to 7FFFFh Address Range (×16) 00000h to 07FFFh 08000h to 0FFFFh 10000h to 17FFFh 18000h to 1FFFFh 20000h to 27FFFh 28000h to 2FFFFh 30000h to 37FFFh 38000h to 3BFFFh 3C000h to 3CFFFh 3D000h to 3DFFFh 3E000h to 3FFFFh Sector Address Tables (MBM29LV400BC) Sector Address SA0 SA1 SA2 SA3 SA4 SA5 SA6 SA7 SA8 SA9 SA10 A17 0 0 0 0 0 0 0 1 1 1 1 A16 0 0 0 0 0 1 1 0 0 1 1 A15 0 0 0 0 1 0 1 0 1 0 1 A14 0 0 0 1 X X X X X X X A13 0 1 1 X X X X X X X X A12 X 0 1 X X X X X X X X Address Range (×8) 00000h to 03FFFh 04000h to 05FFFh 06000h to 07FFFh 08000h to 0FFFFh 10000h to 1FFFFh 20000h to 2FFFFh 30000h to 3FFFFh 40000h to 4FFFFh 50000h to 5FFFFh 60000h to 6FFFFh 70000h to 7FFFFh Address Range (×16) 00000h to 01FFFh 02000h to 02FFFh 03000h to 03FFFh 04000h to 07FFFh 08000h to 0FFFFh 10000h to 17FFFh 18000h to 1FFFFh 20000h to 27FFFh 28000h to 2FFFFh 30000h to 37FFFh 38000h to 3FFFFh 13 MBM29LV400TC-55/70/90/MBM29LV400BC-55/70/90 s FUNCTIONAL DESCRIPTION 1. Read Mode The MBM29LV400TC/BC have two control functions which must be satisfied in order to obtain data at the outputs. CE is the power control and should be used for a device selection. OE is the output control and should be used to gate data to the output pins if a device is selected. Address access time (tACC) is equal to the delay from stable addresses to valid output data. The chip enable access time (tCE) is the delay from stable addresses and stable CE to valid data at the output pins. The output enable access time is the delay from the falling edge of OE to valid data at the output pins. (Assuming the addresses have been stable for at least tACC-tOE time.) When reading out a data without changing addresses after power-up, it is necessary to input hardware reset or change CE pin from “H” or “L” 2. Standby Mode There are two ways to implement the standby mode on the MBM29LV400TC/BC devices, one using both the CE and RESET pins; the other via the RESET pin only. When using both pins, a CMOS standby mode is achieved with CE and RESET inputs both held at VCC ± 0.3 V. Under this condition the current consumed is less than 5 µA. The device can be read with standard access time (tCE) from either of these standby modes. During Embedded Algorithm operation, VCC active current (ICC2) is required even CE = “H”. When using the RESET pin only, a CMOS standby mode is achieved with RESET input held at VSS ± 0.3 V (CE = “H” or “L”). Under this condition the current is consumed is less than 5 µA. Once the RESET pin is taken high, the device requires tRH of wake up time before outputs are valid for read access. In the standby mode the outputs are in the high impedance state, independent of the OE input. 3. Automatic Sleep Mode There is a function called automatic sleep mode to restrain power consumption during read-out of MBM29LV400TC/400BC data. This mode can be used effectively with an application requested low power consumption such as handy terminals. To activate this mode, MBM29LV400TC/400BC automatically switch themselves to low power mode when MBM29LV400TC/400BC addresses remain stably during access fine of 150 ns. It is not necessary to control CE, WE, and OE on the mode. Under the mode, the current consumed is typically 1 µA (CMOS Level). Since the data are latched during this mode, the data are read-out continuously. If the addresses are changed, the mode is canceled automatically and MBM29LV400TC/400BC read-out the data for changed addresses. 4. Output Disable With the OE input at a logic high level (VIH), output from the devices are disabled. This will cause the output pins to be in a high impedance state. 5. Autoselect The autoselect mode allows the reading out of a binary code from the devices and will identify its manufacturer and type. This mode is intended for use by programming equipment for the purpose of automatically matching the devices to be programmed with its corresponding programming algorithm. This mode is functional over the entire temperature range of the devices. To activate this mode, the programming equipment must force VID (11.5 V to 12.5 V) on address pin A9. Two identifier bytes may then be sequenced from the devices outputs by toggling address A0 from VIL to VIH. All addresses are DON’T CARES except A0, A1, A6, and A-1. (See “MBM29LV400TC/400BC Sector Protection Verify Autoselect Codes Table” in sDEVICE BUS OPERATIONS.) 14 MBM29LV400TC-55/70/90/MBM29LV400BC-55/70/90 The manufacturer and device codes may also be read via the command register, for instances when the MBM29LV400TC/BC are erased or programmed in a system without access to high voltage on the A9 pin. The command sequence is illustrated in “MBM29LV400TC/400BC Standard Command Definitions Table” (sDEVICE BUS OPERATIONS). (Refer to “2. Autoselect Command” in sCOMMAND DEFINITIONS.) Byte 0 (A0 = VIL) represents the manufacturer’s code (Fujitsu = 04h) and (A0 = VIH) represents the device identifier code (MBM29LV400TC = B9h and MBM29LV400BC = BAh for ×8 mode; MBM29LV400TC = 22B9h and MBM29LV400BC = 22BAh for ×16 mode). These two bytes/words are given in “MBM29LV400TC/400BC Sector Protection Verify Autoselect Codes Table” and “Extended Autoselect Code Table” (sDEVICE BUS OPERATIONS). All identifiers for manufactures and device will exhibit odd parity with DQ7 defined as the parity bit. In order to read the proper device codes when executing the autoselect, A1 must be VIL. (See “MBM29LV400TC/400BC Sector Protection Verify Autoselect Codes Table” and “Extended Autoselect Code Table” in sDEVICE BUS OPERATIONS.) 6. Write Device erasure and programming are accomplished via the command register. The contents of the register serve as inputs to the internal state machine. The state machine outputs dictate the function of the device. The command register itself does not occupy any addressable memory location. The register is a latch used to store the commands, along with the address and data information needed to execute the command. The command register is written by bringing WE to VIL, while CE is at VIL and OE is at VIH. Addresses are latched on the falling edge of WE or CE, whichever happens later; while data is latched on the rising edge of WE or CE, whichever happens first. Standard microprocessor write timings are used. Refer to AC Write Characteristics and the Erase/Programming Waveforms for specific timing parameters. 7. Sector Protection The MBM29LV400TC/BC feature hardware sector protection. This feature will disable both program and erase operations in any number of sectors (0 through 10). The sector protection feature is enabled using programming equipment at the user’s site. The devices are shipped with all sectors unprotected. Alternatively, Fujitsu may program and protect sectors in the factory prior to shiping the device. To activate this mode, the programming equipment must force VID on address pin A9 and control pin OE, (suggest VID = 11.5 V), CE = VIL, and A6 = VIL. The sector addresses ( A17, A16, A15, A14, A13, and A12) should be set to the sector to be protected. “Sector Address Tables (MBM29LV400TC/BC)” in sFLEXIBLE SECTOR-ERASE ARCHITECTURE define the sector address for each of the eleven (11) individual sectors. Programming of the protection circuitry begins on the falling edge of the WE pulse and is terminated with the rising edge of the same. Sector addresses must be held constant during the WE pulse. See “13. AC Waveforms for Sector Protection Timing Diagram” in sTIMING DIAGRAM and “5. Sector Protection Algorithm” in sFLOW CHART for sector protection waveforms and algorithm. To verify programming of the protection circuitry, the programming equipment must force VID on address pin A9 with CE and OE at VIL and WE at VIH. Scanning the sector addresses ( A17, A16, A15, A14, A13, and A12) while (A6, A1, A0) = (0, 1, 0) will produce a logical “1” code at device output DQ0 for a protected sector. Otherwise the devices will read 00h for unprotected sector. In this mode, the lower order addresses, except for A0, A1, and A6 are DON’T CARES. Address locations with A1 = VIL are reserved for Autoselect manufacturer and device codes. A-1 requires to apply to VIL on byte mode. It is also possible to determine if a sector is protected in the system by writing an Autoselect command. Performing a read operation at the address location XX02h, where the higher order addresses (A17, A16, A15, A14, A13, and A12) are the desired sector address will produce a logical “1” at DQ0 for a protected sector. See “MBM29LV400TC/ 400BC Sector Protection Verify Autoselect Codes Table” and “Extended Autoselect Code Table” in sDEVICE BUS OPERATIONS for Autoselect codes. 15 MBM29LV400TC-55/70/90/MBM29LV400BC-55/70/90 8. Temporary Sector Unprotection This feature allows temporary unprotection of previously protected sectors of the MBM29LV400TC/BC devices in order to change data. The Sector Unprotection mode is activated by setting the RESET pin to high voltage (12 V). During this mode, formerly protected sectors can be programmed or erased by selecting the sector addresses. Once the 12 V is taken away from the RESET pin, all the previously protected sectors will be protected again. See “14. Temporary Sector Unprotection Timing Diagram” in sTIMING DIAGRAM and “6. Temporary Sector Unprotection Algorithm” in sFLOW CHART. 9. RESET Hardware Reset The MBM29LV400TC/BC devices may be reset by driving the RESET pin to VIL. The RESET pin has a pulse requirement and has to be kept low (VIL) for at least 500 ns in order to properly reset the internal state machine. Any operation in the process of being executed will be terminated and the internal state machine will be reset to the read mode 20 µs after the RESET pin is driven low. Furthermore, once the RESET pin goes high, the devices require an additional tRH before it will allow read access. When the RESET pin is low, the devices will be in the standby mode for the duration of the pulse and all the data output pins will be tri-stated. If a hardware reset occurs during a program or erase operation, the data at that particular location will be corrupted. Please note that the RY/BY output signal should be ignored during the RESET pulse. See “9. RESET/RY/BY Timing Diagram” in sTIMING DIAGRAM for the timing diagram. Refer to “8. Temporary Sector Unprotection” for additional functionality. If hardware reset occurs during Embedded Erase Algorithm, there is a possibility that the erasing sector(s) cannot be used. 16 MBM29LV400TC-55/70/90/MBM29LV400BC-55/70/90 s COMMAND DEFINITIONS Device operations are selected by writing specific address and data sequences into the command register. Writing incorrect address and data values or writing them in the improper sequence will reset the devices to the read mode. “MBM29LV400TC/400BC Standard Command Definitions Table” in sDEVICE BUS OPERATIONS defines the valid register command sequences. Note that the Erase Suspend (B0h) and Erase Resume (30h) commands are valid only while the Sector Erase operation is in progress. Moreover both Read/Reset commands are functionally equivalent, resetting the device to the read mode. Please note that commands are always written at DQ0 to DQ7 and DQ8 to DQ15 bits are ignored. 1. Read/Reset Command In order to return from Autoselect mode or Exceeded Timing Limits (DQ5 = 1) to read/reset mode, the read/reset operation is initiated by writing the Read/Reset command sequence into the command register. Microprocessor read cycles retrieve array data from the memory. The devices remain enabled for reads until the command register contents are altered. The devices will automatically power-up in the read/reset state. In this case, a command sequence is not required to read data. Standard microprocessor read cycles will retrieve array data. This default value ensures that no spurious alteration of the memory content occurs during the power transition. Refer to the AC Read Characteristics and Waveforms for the specific timing parameters. 2. Autoselect Command Flash memories are intended for use in applications where the local CPU alters memory contents. As such, manufacture and device codes must be accessible while the devices reside in the target system. PROM programmers typically access the signature codes by raising A9 to a high voltage. However, multiplexing high voltage onto the address lines is not generally desired system design practice. The device contains an Autoselect command operation to supplement traditional PROM programming methodology. The operation is initiated by writing the Autoselect command sequence into the command register. Following the command write, a read cycle from address XX00h retrieves the manufacture code of 04h. A read cycle from address XX01h for ×16(XX02h for ×8) returns the device code (MBM29LV400TC = B9h and MBM29LV400BC = BAh for ×8 mode; MBM29LV400TC = 22B9h and MBM29LV400BC = 22BAh for ×16 mode). (See “MBM29LV400TC/400BC Sector Protection Verify Autoselect Codes Table” and “Extended Autoselect Code Table” in sDEVICE BUS OPERATIONS.) All manufacturer and device codes will exhibit odd parity with DQ7 defined as the parity bit. Sector state (protection or unprotection) will be informed by address XX02h for ×16 (XX04h for ×8). Scanning the sector addresses (A17, A16, A15, A14, A13, and A12) while (A6, A1, A0) = (0, 1, 0) will produce a logical “1” at device output DQ0 for a protected sector. The programming verification should be perform margin mode on the protected sector. (See “MBM29LV400TC/400BC User Bus Operations Tables (BYTE = VIH and BYTE = VIH)” in sDEVICE BUS OPERATIONS.) To terminate the operation, it is necessary to write the Read/Reset command sequence into the register, and also to write the Autoselect command during the operation, execute it after writing Read/Reset command sequence. 3. Byte/Word Programming The devices are programmed on a byte-by-byte (or word-by-word) basis. Programming is a four bus cycle operation. There are two “unlock” write cycles. These are followed by the program set-up command and data write cycles. Addresses are latched on the falling edge of CE or WE, whichever happens later and the data is latched on the rising edge of CE or WE, whichever happens first. The rising edge of CE or WE (whichever happens first) begins programming. Upon executing the Embedded Program Algorithm command sequence, the system is not required to provide further controls or timings. The device will automatically provide adequate internally generated program pulses and verify the programmed cell margin. 17 MBM29LV400TC-55/70/90/MBM29LV400BC-55/70/90 The automatic programming operation is completed when the data on DQ7 is equivalent to data written to this bit at which time the devices return to the read mode and addresses are no longer latched. (See “Hardware Sequence Flags Table” in sCOMMAND DEFINITIONS.) Therefore, the devices require that a valid address to the devices be supplied by the system at this particular instance of time. Hence, Data Polling must be performed at the memory location which is being programmed. Any commands written to the chip during this period will be ignored. If hardware reset occurs during the programming operation, it is impossible to guarantee the data are being written. Programming is allowed in any sequence and across sector boundaries. Beware that a data “0” cannot be programmed back to a “1”. Attempting to do so may either hang up the device or result in an apparent success according to the data polling algorithm but a read from read/reset mode will show that the data is still “0”. Only erase operations can convert “0”s to “1”s. “1. Embedded ProgramTM Algorithm” in sFLOW CHART illustrates the Embedded ProgramTM Algorithm using typical command strings and bus operations. 4. Chip Erase Chip erase is a six bus cycle operation. There are two “unlock” write cycles. These are followed by writing the “set-up” command. Two more “unlock” write cycles are then followed by the chip erase command. Chip erase does not require the user to program the device prior to erase. Upon executing the Embedded Erase Algorithm command sequence the devices will automatically program and verify the entire memory for an all zero data pattern prior to electrical erase (Preprogram function). The system is not required to provide any controls or timings during these operations. The automatic erase begins on the rising edge of the last WE pulse in the command sequence and terminates when the data on DQ7 is “1” (See “8. Write Operation Status”.) at which time the device returns to read the mode. Chip Erase Time; Sector Erase Time × All sectors + Chip Program Time (Preprogramming) “2. Embedded EraseTM Algorithm” in sFLOW CHART illustrates the Embedded EraseTM Algorithm using typical command strings and bus operations. 5. Sector Erase Sector erase is a six bus cycle operation. There are two “unlock” write cycles. These are followed by writing the “set-up” command. Two more “unlock” write cycles are then followed by the Sector Erase command. The sector address (any address location within the desired sector) is latched on the falling edge of WE, while the command (Data=30h) is latched on the rising edge of WE. After time-out of 50 µs from the rising edge of the last sector erase command, the sector erase operation will begin. Multiple sectors may be erased concurrently by writing the six bus cycle operations on “MBM29LV400TC/400BC Standard Command Definitions Table” (sDEVICE BUS OPERATIONS). This sequence is followed with writes of the Sector Erase command to addresses in other sectors desired to be concurrently erased. The time between writes must be less than 50 µs otherwise that command will not be accepted and erasure will start. It is recommended that processor interrupts be disabled during this time to guarantee this condition. The interrupts can be re-enabled after the last Sector Erase command is written. A time-out of 50 µs from the rising edge of the last WE will initiate the execution of the Sector Erase command(s). If another falling edge of the WE occurs within the 50 µs time-out window the timer is reset. (Monitor DQ3 to determine if the sector erase timer window is still open, see section DQ3, Sector Erase Timer.) Any command other than Sector Erase or Erase Suspend during this time-out period will reset the devices to the read mode, ignoring the previous command string. Resetting the devices once execution has begun will corrupt the data in the sector. In that case, restart the erase on those sectors and allow them to complete. (Refer to “8. Write Operation Status” for Sector Erase Timer operation.) Loading the sector erase buffer may be done in any sequence and with any number of sectors (0 to 10). 18 MBM29LV400TC-55/70/90/MBM29LV400BC-55/70/90 Sector erase does not require the user to program the devices prior to erase. The devices automatically program all memory locations in the sector(s) to be erased prior to electrical erase (Preprogram function). When erasing a sector or sectors the remaining unselected sectors are not affected. The system is not required to provide any controls or timings during these operations. The automatic sector erase begins after the 50 µs time out from the rising edge of the WE pulse for the last sector erase command pulse and terminates when the data on DQ7 is “1” (See “8. Write Operation Status”.) at which time the devices return to the read mode. Data polling must be performed at an address within any of the sectors being erased. Multiple Sector Erase Time; [Sector Erase Time + Sector Program Time (Preprogramming)] × Number of Sector Erase “2. Embedded EraseTM Algorithm” in sFLOW CHART illustrates the Embedded EraseTM Algorithm using typical command strings and bus operations. 6. Erase Suspend The Erase Suspend command allows the user to interrupt a Sector Erase operation and then perform data reads from or programs to a sector not being erased. This command is applicable ONLY during the Sector Erase operation which includes the time-out period for sector erase. The Erase Suspend command will be ignored if written during the Chip Erase operation or Embedded Program Algorithm. Writting the Erase Suspend command during the Sector Erase time-out results in immediate termination of the time-out period and suspension of the erase operation. Writing the Erase Resume command resumes the erase operation. The addresses are DON’T CARES when writing the Erase Suspend or Erase Resume command. When the Erase Suspend command is written during the Sector Erase operation, the device will take a maximum of 20 µs to suspend the erase operation. When the devices have entered the erase-suspended mode, the RY/ BY output pin and the DQ7 bit will be at logic “1”, and DQ6 will stop toggling. The user must use the address of the erasing sector for reading DQ6 and DQ7 to determine if the erase operation has been suspended. Further writes of the Erase Suspend command are ignored. When the erase operation has been suspended, the devices default to the erase-suspend-read mode. Reading data in this mode is the same as reading from the standard read mode except that the data must be read from sectors that have not been erase-suspended. Successively reading from the erase-suspended sector while the device is in the erase-suspend-read mode will cause DQ2 to toggle. (See the section on DQ2.) After entering the erase-suspend-read mode, the user can program the device by writing the appropriate command sequence for Program. This program mode is known as the erase-suspend-program mode. Again, programming in this mode is the same as programming in the regular Program mode except that the data must be programmed to sectors that are not erase-suspended. Successively reading from the erase-suspended sector while the devices are in the erase-suspend-program mode will cause DQ2 to toggle. The end of the erasesuspended Program operation is detected by the RY/BY output pin, Data polling of DQ7, or by the Toggle Bit I (DQ6) which is the same as the regular Program operation. Note that DQ7 must be read from the Program address while DQ6 can be read from any address. To resume the operation of Sector Erase, the Resume command (30h) should be written. Any further writes of the Resume command at this point will be ignored. Another Erase Suspend command can be written after the chip has resumed erasing. 7. Extended Command (1) Fast Mode MBM29LV400TC/BC has Fast Mode function. This mode dispenses with the initial two unclock cycles required in the standard program command sequence by writing Fast Mode command into the command 19 MBM29LV400TC-55/70/90/MBM29LV400BC-55/70/90 register. In this mode, the required bus cycle for programming is two cycles instead of four bus cycles in standard program command. (Do not write erase command in this mode.) The read operation is also executed after exiting this mode. To exit this mode, it is necessary to write Fast Mode Reset command into the command register. (Refer to “8. Embedded ProgramTM Algorithm for Fast Mode” in sFLOW CHART Extended algorithm.) The VCC active current is required even CE = VIH during Fast Mode. (2) Fast Programming During Fast Mode, the programming can be executed with two bus cycles operation. The Embedded Program Algorithm is executed by writing program set-up command (A0h) and data write cycles (PA/PD). (Refer to “8. Embedded ProgramTM Algorithm for Fast Mode” in sFLOW CHART Extended algorithm.) (3) Extended Sector Protection In addition to normal sector protection, the MBM29LV400TC/BC has Extended Sector Protection as extended function. This function enable to protect sector by forcing VID on RESET pin and write a commnad sequence. Unlike conventional procedure, it is not necessary to force VID and control timing for control pins. The only RESET pin requires VID for sector protection in this mode. The extended sector protect requires VID on RESET pin. With this condition, the operation is initiated by writing the set-up command (60h) into the command register. Then, the sector addresses pins (A17, A16, A15, A14, A13 and A12) and (A6, A1, A0) = (0, 1, 0) should be set to the sector to be protected (recommend to set VIL for the other addresses pins), and write extended sector protect command (60h). A sector is typically protected in 150 µs. To verify programming of the protection circuitry, the sector addresses pins (A17, A16, A15, A14, A13 and A12) and (A6, A1, A0) = (0, 1, 0) should be set and write a command (40h). Following the command write, a logical “1” at device output DQ0 will produce for protected sector in the read operation. If the output data is logical “0”, please repeat to write extended sector protect command (60h) again. To terminate the operation, it is necessary to set RESET pin to VIH. 8. Write Operation Status Status Embedded Program Algorithm Embedded Erase Algorithm In Progress Erase Suspend Read (Erase Suspended Sector) Erase Erase Suspend Read Suspende (Non-Erase Suspended Sector) d Mode Erase Suspend Program (Non-Erase Suspended Sector) Embedded Program Algorithm Exceeded Embedded Erase Algorithm Time Erase Limits Erase Suspend Program Suspende (Non-Erase Suspended Sector) d Mode Hardware Sequence Flags DQ7 DQ7 0 1 Data DQ7 DQ7 0 DQ7 DQ6 Toggle Toggle 1 Data Toggle Toggle Toggle Toggle DQ5 0 0 0 Data 0 1 1 1 DQ3 0 1 0 Data 0 0 1 0 DQ2 1 Toggle*1 Toggle Data 1 *2 1 N/A N/A *1:Successive reads from the erasing or erase-suspend sector cause DQ2 to toggle. *2: Reading from non-erase suspend sector address indicates logic “1” at the DQ2 bit. 20 MBM29LV400TC-55/70/90/MBM29LV400BC-55/70/90 9. DQ7 Data Polling The MBM29LV400TC/BC devices feature Data Polling as a method to indicate to the host that the Embedded Algorithms are in progress or completed. During the Embedded Program Algorithm an attempt to read the devices will produce the complement of the data last written to DQ7. Upon completion of the Embedded Program Algorithm, an attempt to read the device will produce the true data last written to DQ7. During the Embedded Erase Algorithm, an attempt to read the device will produce a “0” at the DQ7 output. Upon completion of the Embedded Erase Algorithm an attempt to read the device will produce a “1” at the DQ7 output. The flowchart for Data Polling (DQ7) is shown in “3. Data Polling Algorithm” (sFLOW CHART). For chip erase and sector erase, the Data Polling is valid after the rising edge of the sixth WE pulse in the six write pulse sequence. Data Polling must be performed at sector address within any of the sectors being erased and not a protected sector. Otherwise, the status may not be valid. Once the Embedded Algorithm operation is close to being completed, the MBM29LV400TC/BC data pins (DQ7) may change asynchronously while the output enable (OE) is asserted low. This means that the devices are driving status information on DQ7 at one instant of time and then that byte’s valid data at the next instant of time. Depending on when the system samples the DQ7 output, it may read the status or valid data. Even if the device has completed the Embedded Algorithm operation and DQ7 has a valid data, the data outputs on DQ0 to DQ6 may be still invalid. The valid data on DQ0 to DQ7 will be read on the successive read attempts. The Data Polling feature is only active during the Embedded Programming Algorithm, Embedded Erase Algorithm or sector erase time-out. (See “Hardware Sequence Flags Table” in sCOMMAND DEFINITIONS.) See “6. AC Waveforms for Data Polling during Embedded Algorithm Operations” in sTIMING DIAGRAM for the Data Polling timing specifications and diagrams. 10. DQ6 Toggle Bit I The MBM29LV400TC/BC also feature the “Toggle Bit I” as a method to indicate to the host system that the Embedded Algorithms are in progress or completed. During an Embedded Program or Erase Algorithm cycle, successive attempts to read (OE toggling) data from the devices will result in DQ6 toggling between one and zero. Once the Embedded Program or Erase Algorithm cycle is completed, DQ6 will stop toggling and valid data will be read on the next successive attempts. During programming, the Toggle Bit I is valid after the rising edge of the fourth WE pulse in the four write pulse sequence. For chip erase and sector erase, the Toggle Bit I is valid after the rising edge of the sixth WE pulse in the six write pulse sequence. The Toggle Bit I is active during the sector time out. In programming, if the sector being written to is protected, the toggle bit will toggle for about 2 µs and then stop toggling without the data having changed. In erase, the devices will erase all the selected sectors except for the ones that are protected. If all selected sectors are protected, the chip will toggle the toggle bit for about 100 µs and then drop back into read mode, having changed none of the data. Either CE or OE toggling will cause the DQ6 to toggle. In addition, an Erase Suspend/Resume command will cause the DQ6 to toggle. See “7. AC Waveforms for Toggle Bit I during Embedded Algorithm Operations” in sTIMING DIAGRAM for the Toggle Bit I timing specifications and diagrams. 21 MBM29LV400TC-55/70/90/MBM29LV400BC-55/70/90 11. DQ5 Exceeded Timing Limits DQ5 will indicate if the program or erase time has exceeded the specified limits (internal pulse count). Under these conditions DQ5 will produce a “1”. This is a failure condition which indicates that the program or erase cycle was not successfully completed. Data Polling is the only operating function of the devices under this condition. The CE circuit will partially power down the device under these conditions (to approximately 2 mA). The OE and WE pins will control the output disable functions as described in “MBM29LV400TC/400BC User Bus Operations Tables (BYTE = VIH and BYTE = VIH)” (sDEVICE BUS OPERATIONS). The DQ5 failure condition may also appear if a user tries to program a non blank location without erasing. In this case the devices lock out and never complete the Embedded Algorithm operation. Hence, the system never reads a valid data on DQ7 bit and DQ6 never stops toggling. Once the devices have exceeded timing limits, the DQ5 bit will indicate a “1.” Please note that this is not a device failure condition since the devices were incorrectly used. If this occurs, reset the device with command sequence. 12. DQ3 Sector Erase Timer After the completion of the initial sector erase command sequence the sector erase time-out will begin. DQ3 will remain low until the time-out is complete. Data Polling and Toggle Bit are valid after the initial sector erase command sequence. If Data Polling or the Toggle Bit I indicates the device has been written with a valid erase command, DQ3 may be used to determine if the sector erase timer window is still open. If DQ3 is high (“1”) the internally controlled erase cycle has begun; attempts to write subsequent commands to the device will be ignored until the erase operation is completed as indicated by Data Polling or Toggle Bit I. If DQ3 is low (“0”), the device will accept additional sector erase commands. To insure the command has been accepted, the system software should check the status of DQ3 prior to and following each subsequent Sector Erase command. If DQ3 were high on the second status check, the command may not have been accepted. See “Hardware Sequence Flags Table” in sCOMMAND DEFINITIONS. 13. DQ2 Toggle Bit II This toggle bit II, along with DQ6, can be used to determine whether the devices are in the Embedded Erase Algorithm or in Erase Suspend. Successive reads from the erasing sector will cause DQ2 to toggle during the Embedded Erase Algorithm. If the devices are in the erase-suspended-read mode, successive reads from the erase-suspended sector will cause DQ2 to toggle. When the devices are in the erase-suspended-program mode, successive reads from the byte address of the non-erase suspended sector will indicate a logic “1” at the DQ2 bit. DQ6 is different from DQ2 in that DQ6 toggles only when the standard program or Erase, or Erase Suspend Program operation is in progress. The behavior of these two status bits, along with that of DQ7, is summarized as follows: For example, DQ2 and DQ6 can be used together to determine if the erase-suspend-read mode is in progress. (DQ2 toggles while DQ6 does not.) See also “Hardware Sequence Flags Table” in sCOMMAND DEFINITIONS and “15. DQ2 vs. DQ6” in sTIMING DIAGRAM. 22 MBM29LV400TC-55/70/90/MBM29LV400BC-55/70/90 Furthermore, DQ2 can also be used to determine which sector is being erased. When the device is in the erase mode, DQ2 toggles if this bit is read from an erasing sector. 14. Reading Toggle Bits DQ6/DQ2 Whenever the system initially begins reading toggle bit status, it must read DQ7 to DQ0 at least twice in a row to determine whether a toggle bit is toggling. Typically, a system would note and store the value of the toggle bit after the first read. After the second read, the system would compare the new value of toggle bit with the first. If the toggle bit is not toggling, this indicates that the device has completed the program or erase operation. The system can read array data on DQ7 to DQ0 on the following read cycle. However, if after the initial two read cycles, the system determines that the toggle bit is still toggling, the system also should note whether the value of DQ5 is high (see “11. DQ5”) . If it is the system should then determine again whether the toggle bit is toggling, since the toggle bit may have stopped toggling just as DQ5 went high. If the toggle bit is no longer toggling, the device has successfully completed the program or erase operation. If it is still toggling, the device did not complete the operation successfully, and the system must write the reset command to return to reading array data. The remaining scenario is that the system initially determines that the toggle bit is toggling and DQ5 has not gone high. The system may continue to monitor the toggle bit and DQ5 though successive read cycles, determining the status as described in the previous paragraph. Alternatively, it may choose to perform other system tasks. In this case, the system must start at the beginning of the algorithm when it returns to determine the status of operation. (See “4. Toggle Bit Algorithm” in s FLOW CHART.) Toggle Bit Status Table Mode Program Erase Erase-Suspend Read (Erase-Suspend Sector) Erase-Suspend Program DQ7 DQ7 0 1 DQ7 DQ6 Toggle Toggle 1 Toggle DQ2 1 Toggle*1 Toggle 1*2 *1 : Successive reads from the erasing or erase-suspend sector cause DQ2 to toggle. *2 : Reading from non-erase suspend sector address indicates logic “1” at the DQ2 bit. 15. RY/BY Ready/Busy The MBM29LV400TC/BC provide a RY/BY open-drain output pin as a way to indicate to the host system that the Embedded Algorithms are either in progress or has been completed. If the output is low, the devices are busy with either a program or erase operation. If the output is high, the devices are ready to accept any read/ write or erase operation. When the RY/BY pin is low, the devices will not accept any additional program or erase commands. If the MBM29LV400TC/BC are placed in an Erase Suspend mode, the RY/BY output will be high. During programming, the RY/BY pin is driven low after the rising edge of the fourth WE pulse. During an erase operation, the RY/BY pin is driven low after the rising edge of the sixth WE pulse. The RY/BY pin will indicate a busy condition during the RESET pulse. Refer to “8. RY/BY Timing Diagram during Program/Erase Operations” and “9. RESET/RY/BY Timing Diagram” in sTIMING DIAGRAM for a detailed timing diagram. The RY/BY pin is pulled high in standby mode. Since this is an open-drain output, the pull-up resistor needs to be connected to VCC; multiples of devices may be connected to the host system via more than one RY/BY pin in parallel. 23 MBM29LV400TC-55/70/90/MBM29LV400BC-55/70/90 16. Byte/Word Configuration The BYTE pin selects the byte (8-bit) mode or word (16-bit) mode for the MBM29LV400TC/BC devices. When this pin is driven high, the devices operate in the word (16-bit) mode. The data is read and programmed at DQ0 to DQ15. When this pin is driven low, the devices operate in byte (8-bit) mode. Under this mode, the DQ15/A-1 pin becomes the lowest address bit and DQ8 to DQ14 bits are tri-stated. However, the command bus cycle is always an 8-bit operation and hence commands are written at DQ0 to DQ7 and the DQ8 to DQ15 bits are ignored. Refer to “10. Timing Diagram for Word Mode Configuration” and “11. Timing Diagram for Byte Mode Configuration” and “12. BYTE Timing Diagram for Write Operations” in sTIMING DIAGRAM for the timing diagram. 17. Data Protection The MBM29LV400TC/BC are designed to offer protection against accidental erasure or programming caused by spurious system level signals that may exist during power transitions. During power up the devices automatically reset the internal state machine in the Read mode. Also, with its control register architecture, alteration of the memory contents only occurs after successful completion of specific multi-bus cycle command sequences. The devices also incorporate several features to prevent inadvertent write cycles resulting form VCC power-up and power-down transitions or system noise. 18. Low VCC Write Inhibit To avoid initiation of a write cycle during VCC power-up and power-down, a write cycle is locked out for VCC less than 2.3 V (typically 2.4 V). If VCC < VLKO, the command register is disabled and all internal program/erase circuits are disabled. Under this condition the device will reset to the read mode. Subsequent writes will be ignored until the VCC level is greater than VLKO. It is the users responsibility to ensure that the control pins are logically correct to prevent unintentional writes when VCC is above 2.3 V. If Embedded Erase Algorithm is interrupted, there is possibility that the erasing sector(s) cannot be used. 19. Write Pulse “Glitch” Protection Noise pulses of less than 3 ns (typical) on OE, CE, or WE will not initiate a write cycle. 20. Logical Inhibit Writing is inhibited by holding any one of OE = VIL, CE = VIH, or WE = VIH. To initiate a write cycle CE and WE must be a logical zero while OE is a logical one. 21. Power-Up Write Inhibit Power-up of the devices with WE = CE = VIL and OE = VIH will not accept commands on the rising edge of WE. The internal state machine is automatically reset to the read mode on power-up. 22. Sector Protection Device user is able to protect each sector individually to store and protect data. Protection circuit voids both program and erase commands that are addressed to protected sectors. Any commands to program or erase addressed to protected sector are ignored (see “Sector Protection” in s FUNCTIONAL DESCRIPTION) . 24 MBM29LV400TC-55/70/90/MBM29LV400BC-55/70/90 s ABSOLUTE MAXIMUM RATINGS Parameter Storage Temperature Ambient Temperature with Power Applied Voltage with Respect to Ground All pins except A9, OE, RESET *1,*2 A9, OE and RESET *1,*3 Power Supply Voltage * 1 Symbol Tstg TA VIN, VOUT VIN VCC Rating Min –55 –40 –0.5 –2.0 –0.5 Max +125 +85 VCC+0.5 +13.0 +5.5 Unit °C °C V V V *1: Voltage is defined on the basis of VSS = GND = 0 V. *2: Minimum DC voltage on input or I/O pins is –0.5 V. During voltage transitions, input or I/O pins may undershoot VSS to –2.0 V for periods of up to 20 ns. Maximum DC voltage on input or I/O pins is VCC +0.5 V. During voltage transitions, input or I/O pins may overshoot to VCC +2.0 V for periods of up to 20 ns. *3: Minimum DC input voltage on A9, OE and RESET pins is –0.5 V. During voltage transitions, A9, OE and RESET pins may undershoot VSS to –2.0 V for periods of up to 20 ns. Voltage difference between input and supply voltage (VIN – VCC) does not exceed +9.0 V. Maximum DC input voltage on A9, OE and RESET pins is +13.0 V which may overshoot to +14.0 V for periods of up to 20 ns. WARNING: Semiconductor devices can be permanently damaged by application of stress (voltage, current, temperature, etc.) in excess of absolute maximum ratings. Do not exceed these ratings. s RECOMMENDED OPERATING CONDITIONS Parameter Ambient Temperature Power Supply Voltage* Symbol TA VCC Part Number MBM29LV400TC/BC-55 MBM29LV400TC/BC-70/-90 MBM29LV400TC/BC-55 MBM29LV400TC/BC-70/-90 Value Min –20 –40 +3.0 +2.7 Max +70 +85 +3.6 Unit °C °C V * : Voltage is defined on the basis of VSS = GND = 0 V. Note: Operating ranges define those limits between which the functionality of the devices are guaranteed. WARNING: The recommended operating conditions are required in order to ensure the normal operation of the semiconductor device. All of the device’s electrical characteristics are warranted when the device is operated within these ranges. Always use semiconductor devices within their recommended operating condition ranges. Operation outside these ranges may adversely affect reliability and could result in device failure. No warranty is made with respect to uses, operating conditions, or combinations not represented on the data sheet. Users considering application outside the listed conditions are advised to contact their FUJITSU representatives beforehand. 25 MBM29LV400TC-55/70/90/MBM29LV400BC-55/70/90 s MAXIMUM OVERSHOOT/ MAXIMUM UNDERSHOOT +0.6 V −0.5 V −2.0 V 20 ns 20 ns 20 ns Figure 1 Maximum Undershoot Waveform 20 ns VCC +2.0 V VCC +0.5 V +2.0 V 20 ns 20 ns Figure 2 Maximum Overshoot Waveform 1 20 ns +14.0 V +13.0 V VCC +0.5 V 20 ns 20 ns Note: This waveform is applied for A9, OE, and RESET. Figure 3 Maximum Overshoot Waveform 2 26 MBM29LV400TC-55/70/90/MBM29LV400BC-55/70/90 s DC CHARACTERISTICS Parameter Input Leakage Current Output Leakage Current A9, OE, RESET Inputs Leakage Current Symbol ILI ILO ILIT Test Conditions VIN = VSS to VCC, VCC = VCC Max VOUT = VSS to VCC, VCC = VCC Max VCC = VCC Max A9, OE, RESET = 12.5 V CE = VIL, OE = VIH, f=10 MHz VCC Active Current * 1 Min –1.0 –1.0 — Byte Word Byte Word — — — — — — –0.5 2.0 11.5 — 2.4 VCC–0.4 2.3 Typ         1 1 1   12    2.4 Max +1.0 +1.0 35 22 25 12 15 35 5 5 5 0.6 VCC+0.3 12.5 0.45 — — 2.5 Unit µA µA µA mA mA mA µA µA µA V V V V V V V ICC1 CE = VIL, OE = VIH, f=5 MHz VCC Active Current *2 VCC Current (Standby) VCC Current (Standby, Reset) VCC Current (Automatic Sleep Mode) *3 Input Low Voltage Input High Voltage Voltage for Autoselect and Sector Protection (A9, OE, RESET) *4, *5 Output Low Voltage Output High Voltage Low VCC Lock-Out Voltage ICC2 ICC3 ICC4 ICC5 VIL VIH VID VOL VOH1 VOH2 VLKO CE = VIL, OE = VIH VCC = VCC Max, CE = VCC ± 0.3 V, RESET = VCC ± 0.3 V VCC = VCC Max, RESET = VSS ± 0.3 V VCC = VCC Max, CE = VSS ± 0.3 V, RESET = VCC ± 0.3 V VIN = VCC ± 0.3 V or VSS ± 0.3 V — — — IOL = 4.0 mA, VCC = VCC Min IOH = –2.0 mA, VCC = VCC Min IOH = –100 µA — *1: The ICC current listed includes both the DC operating current and the frequency dependent component (at 10 MHz). *2: ICC active while Embedded Algorithm (program or erase) is in progress. *3: Automatic sleep mode enables the low power mode when address remain stable for 150 ns. *4: This timing is only for Sector Protection operation and Autoselect mode. *5: (VID – VCC) do not exceed 9 V. 27 MBM29LV400TC-55/70/90/MBM29LV400BC-55/70/90 s AC CHARACTERISTICS • Read Only Operations Characteristics Parameter Read Cycle Time Address to Output Delay Chip Enable to Output Delay Output Enable to Output Delay Chip Enable to Output High-Z Output Enable to Output High-Z Output Hold Time From Addresses, CE or OE, Whichever Occurs First RESET Pin Low to Read Mode CE to BYTE Switching Low or High Symbol JEDEC Standard Value * Test Setup — CE = VIL OE = VIL OE = VIL — — — — — — 55      0   -55  55 55 30 25 25  20 5 70      0   -70  70 70 30 25 25  20 5 90      0   -90  90 90 35 30 30  20 5 Unit ns ns ns ns ns ns ns µs ns Min Max Min Max Min Max tAVAV tAVQV tELQV tGLQV tEHQZ tGHQZ tAXQX — — tRC tACC tCE tOE tDF tDF tOH tREADY tELFL, tELFH *: Test Conditions: Output Load: 1 TTL gate and 30 pF (MBM29LV400TC/BC-55/70) 1 TTL gate and 100 pF (MBM29LV400TC/BC-90) Input rise and fall times: 5 ns Input pulse levels: 0.0 V or 3.0 V Timing measurement reference level Input: 1.5 V Output:1.5 V 3.3 V IN3064 or Equivalent Device Under Test 6.2 kΩ CL Diodes = IN3064 or Equivalent 2.7 kΩ Notes: CL = 30 pF including jig capacitance (MBM29LV400TC/BC-55/70) CL = 100 pF including jig capacitance (MBM29LV400TC/BC-90) Figure 4 Test Conditions 28 MBM29LV400TC-55/70/90/MBM29LV400BC-55/70/90 • Write/Erase/Program Operations Parameter Write Cycle Time Address Setup Time Address Hold Time Data Setup Time Data Hold Time Output Enable Setup Time Output Enable Hold Time Read Toggle and Data Polling Symbol tAVAV tAVWL tWLAX tDVWH tWHDX — — tGHWL tGHEL tELWL tWLEL tWHEH tEHWH tWLWH tELEH tWHWL tEHEL tWHWH1 tWHWH2 — — 2 -55 55 0 45 30 0 0 0 10 0 0 0 0 0 0 30 30 25 25    50 4 4 4 0                   8 16 1                                70 0 45 35 0 0 0 10 0 0 0 0 0 0 35 35 25 25    50 4 4 4 0 -70                   8 16 1                                90 0 45 45 0 0 0 10 0 0 0 0 0 0 45 45 25 25    50 4 4 4 0 -90                   8 16 1                                    30 90 90 90 JEDEC Standard Min Typ Max Min Typ Max Min Typ Max Unit ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns µs µs s µs ns µs µs µs µs ns ns ns ns ns ns ns tWC tAS tAH tDS tDH tOES tOEH tGHWL tGHEL tCS tWS tCH tWH tWP tCP tWPH tCPH tWHWH1 tWHWH2 tVCS tVIDR tVLHT tWPP tOESP tCSP tRB tRP tRH tFLQZ tFHQV tBUSY tEOE Read Recover Time Before Write Read Recover Time Before Write CE Setup Time WE Setup Time CE Hold Time WE Hold Time Write Pulse Width CE Pulse Width Write Pulse Width High CE Pulse Width High Programming Operation Byte Word Sector Erase Operation *1 VCC Setup Time Rise Time to VID *2 Voltage Transition Time * Write Pulse Width * 2 500  100   500   100   500   100  — — — — — — — — — — — OE Setup Time to WE Active *2 CE Setup Time to WE Active *2 Recover Time From RY/BY RESET Pulse Width RESET Hold Time Before Read BYTE Switching Low to Output High-Z BYTE Switching High to Output Active Program/Erase Valid to RY/BY Delay Delay Time from Embedded Output Enable 500  200           500   200  25 55 90 55          500   200  25 70 90 70         *1: This does not include the preprogramming time. *2: This timing is for Sector Protection operation. 29 MBM29LV400TC-55/70/90/MBM29LV400BC-55/70/90 s ERASE AND PROGRAMMING PERFORMANCE Limits Parameter Min Sector Erase Time Word Programming Time Byte Programming Time Chip Programming Time Program/Erase Cycle — — — — 100,000 Typ 1 16 8 4.2 — Max 10 360 300 12.5 — s µs µs s cycle Excludes programming time prior to erasure Excludes system-level overhead Excludes system-level overhead — Unit Comments s TSOP(1) PIN CAPACITANCE Parameter Symbol CIN COUT CIN2 Parameter Description Input Capacitance Output Capacitance Control Pin Capacitance Test Setup VIN = 0 VOUT = 0 VIN = 0 Typ 7.5 8 9.5 Max 9 10 12.5 Unit pF pF pF Notes: • Test conditions TA = + 25°C, f = 1.0 MHz • DQ15/A-1 pin capacitance is stipulated by output capacitance. s SOP PIN CAPACITANCE Parameter Symbol CIN COUT CIN2 Parameter Description Input Capacitance Output Capacitance Control Pin Capacitance Test Setup VIN = 0 VOUT = 0 VIN = 0 Typ 7.5 8 9.5 Max 9 10 12.5 Unit pF pF pF Notes: • Test conditions TA = + 25°C, f = 1.0 MHz • DQ15/A-1 pin capacitance is stipulated by output capacitance. s CSOP PIN CAPACITANCE Parameter Symbol CIN COUT CIN2 Parameter Description Input Capacitance Output Capacitance Control Pin Capacitance Test Setup VIN = 0 VOUT = 0 VIN = 0 Typ 7.5 8 9.5 Max 9 10 12.5 Unit pF pF pF Notes: • Test conditions TA = + 25°C, f = 1.0 MHz • DQ15/A-1 pin capacitance is stipulated by output capacitance. 30 MBM29LV400TC-55/70/90/MBM29LV400BC-55/70/90 s FBGA PIN CAPACITANCE Parameter Symbol CIN COUT CIN2 Parameter Description Input Capacitance Output Capacitance Control Pin Capacitance Test Setup VIN = 0 VOUT = 0 VIN = 0 Typ 7.5 8 9.5 Max 9 10 12.5 Unit pF pF pF Notes: • Test conditions TA = + 25°C, f = 1.0 MHz • DQ15/A-1 pin capacitance is stipulated by output capacitance. s SCSP PIN CAPACITANCE Parameter Symbol CIN COUT CIN2 Parameter Description Input Capacitance Output Capacitance Control Pin Capacitance Test Setup VIN = 0 VOUT = 0 VIN = 0 Typ 7.5 8 9.5 Max 9 10 12.5 Unit pF pF pF Notes: • Test conditions TA = + 25°C, f = 1.0 MHz • DQ15/A-1 pin capacitance is stipulated by output capacitance. 31 MBM29LV400TC-55/70/90/MBM29LV400BC-55/70/90 s TIMING DIAGRAM • Key to Timing Diagram WAVEFORM INPUTS Must Be Steady May Change from H to L May Change from L to H “H” or “L” Any Change Permitted Does Not Apply OUTPUTS Will Be Steady Will Be Changing from H to L Will Be Changing from L to H Changing State Unknown Center Line is HighImpedance “Off” State 1. AC Waveforms for Read Operations tRC Address Address Stable tACC CE tOE tDF OE tOEH WE tCE tOH Outputs High-Z Output Valid High-Z 32 MBM29LV400TC-55/70/90/MBM29LV400BC-55/70/90 2. AC Waveforms for Hardware Reset/Read Operations tRC Address tACC tRH Address Stable RESET tOH Outputs High-Z Output Valid 3. AC Waveforms for Alternate WE Controlled Program Operations 3rd Bus Cycle Address 555h tWC tAS PA tAH Data Polling PA tRC CE tCS tCH tCE OE tGHWL tWP tWPH tWHWH1 tOE WE tDS tDH tDF tOH Data A0h PD DQ7 DOUT DOUT Notes: • • • • • • PA is address of the memory location to be programmed. PD is data to be programmed at byte address. DQ7 is the output of the complement of the data written to the device. DOUT is the output of the data written to the device. Figure indicates last two bus cycles out of four bus cycle sequence. These waveforms are for the ×16 mode. The addresses differ from ×8 mode. 33 MBM29LV400TC-55/70/90/MBM29LV400BC-55/70/90 4. AC Waveforms for Alternate CE Controlled Program Operations 3rd Bus Cycle Data Polling PA tAS tAH PA Address 555h tWC WE tWS tWH OE tGHEL tCP tCPH tWHWH1 CE tDS tDH Data A0h PD DQ7 DOUT Notes: • • • • • • PA is address of the memory location to be programmed. PD is data to be programmed at byte address. DQ7 is the output of the complement of the data written to the device. DOUT is the output of the data written to the device. Figure indicates last two bus cycles out of four bus cycle sequence. These waveforms are for the ×16 mode. The addresses differ from ×8 mode. 34 MBM29LV400TC-55/70/90/MBM29LV400BC-55/70/90 5. AC Waveforms Chip/Sector Erase Operations Address 555h tWC 2AAh tAS tAH 555h 555h 2AAh SA* CE tCS tCH OE tGHWL tWP tWPH WE tDS AAh tDH 55h 80h AAh 55h 10h for Chip Erase 10h/ 30h Data tVCS VCC * : SA is the sector address for Sector Erase. Addresses = 555h (Word), AAAh (Byte) for Chip Erase. Note : These waveforms are for the ×16 mode. The addresses differ from ×8 mode. 35 MBM29LV400TC-55/70/90/MBM29LV400BC-55/70/90 6. AC Waveforms for Data Polling during Embedded Algorithm Operations CE tCH tOE tDF OE tOEH WE tCE * DQ7 Data DQ7 DQ7 = Valid Data High-Z tWHWH1 or 2 DQ0 to DQ6 Data DQ0 to DQ6 = Output Flag tEOE DQ0 to DQ6 Valid Data High-Z tBUSY RY/BY *: DQ7 = Valid Data (The device has completed the Embedded operation). 7. AC Waveforms for Toggle Bit I during Embedded Algorithm Operations CE tOEH WE tOES OE tDH * DQ6 Data tBUSY DQ6 = Toggle DQ6 = Toggle tOE DQ6 = Stop Toggling Valid RY/BY *: DQ6 stops toggling (The device has completed the Embedded operation). 36 MBM29LV400TC-55/70/90/MBM29LV400BC-55/70/90 8. RY/BY Timing Diagram during Program/Erase Operations CE Rising edge of the last WE signal WE Entire programming or erase operations RY/BY tBUSY 9. RESET/RY/BY Timing Diagram WE RESET tRP tRB RY/BY tREADY 10. Timing Diagram for Word Mode Configuration CE tCE BYTE DQ14 to DQ0 tELFH Data Output (DQ7 to DQ0) tFHQV Data Output (DQ14 to DQ0) DQ15 /A-1 A-1 DQ15 37 MBM29LV400TC-55/70/90/MBM29LV400BC-55/70/90 11. Timing Diagram for Byte Mode Configuration CE BYTE tELFL DQ14 to DQ0 Data Output (DQ14 to DQ0) tACC Data Output (DQ7 to DQ0) DQ15 /A-1 DQ15 tFLQZ A-1 12. BYTE Timing Diagram for Write Operations Falling edge of the last write signal CE or WE BYTE tAS Input Valid tAH 38 MBM29LV400TC-55/70/90/MBM29LV400BC-55/70/90 13. AC Waveforms for Sector Protection Timing Diagram A17, A16, A15 A14, A13, A12 SPAX SPAY A0 A1 A6 VID VIH A9 tVLHT VID VIH OE tVLHT tWPP tVLHT tVLHT WE tOESP CE tCSP Data tVCS tOE 01h VCC SPAX : Sector Address to be protected SPAY : Next Sector Address to be protected Note: A-1 is VIL on byte mode. 39 MBM29LV400TC-55/70/90/MBM29LV400BC-55/70/90 14. Temporary Sector Unprotection Timing Diagram VCC tVCS VID VIH RESET CE tVIDR tVLHT WE tVLHT RY/BY tVLHT Program or Erase Command Sequence Unprotection Period 15. DQ2 vs. DQ6 Enter Embedded Erasing WE Erase Suspend Erase Enter Erase Suspend Program Erase Suspend Program Erase Resume Erase Suspend Read Erase Erase Complete Erase Suspend Read DQ6 DQ2* Toggle DQ2 and DQ6 with OE or CE * : DQ2 is read from the erase-suspended sector. 40 MBM29LV400TC-55/70/90/MBM29LV400BC-55/70/90 16. Extended Sector Protection Timing Diagram VCC tVCS RESET tVLHT tVIDR tWC tWC SPAX SPAX SPAY Address A0 A1 A6 CE OE tWP TIME-OUT WE Data 60h 60h 40h tOE 01h 60h SPAX: Sector Address to be protected SPAY : Next Sector Address to be protected TIME-OUT : Time-Out window = 150 µs (Min) 41 MBM29LV400TC-55/70/90/MBM29LV400BC-55/70/90 s FLOW CHART 1. Embedded ProgramTM Algorithm EMBEDDED ALGORITHM Start Write Program Command Sequence (See below) Data Polling Embedded Program Algorithm in progress No Verify Data ? Yes Increment Address No Last Address ? Yes Programming Completed Program Command Sequence (Address/Command): 555h/AAh 2AAh/55h 555h/A0h Program Address/Program Data Notes : • The sequence is applied for × 16 mode. • The addresses differ from × 8 mode. 42 MBM29LV400TC-55/70/90/MBM29LV400BC-55/70/90 2. Embedded EraseTM Algorithm EMBEDDED ALGORITHM Start Write Erase Command Sequence (See below) Data Polling Embedded Erase Algorithm in Progress No Data = FFh ? Yes Erasure Completed Chip Erase Command Sequence (Address/Command): 555h/AAh Individual Sector/Multiple Sector Erase Command Sequence (Address/Command): 555h/AAh 2AAh/55h 2AAh/55h 555h/80h 555h/80h 555h/AAh 555h/AAh 2AAh/55h 2AAh/55h 555h/10h Sector Address/30h Sector Address/30h Additional sector erase commands are optional. Sector Address/30h Notes : • The sequence is applied for × 16 mode. • The addresses differ from × 8 mode. 43 MBM29LV400TC-55/70/90/MBM29LV400BC-55/70/90 3. Data Polling Algorithm Start Read Byte (DQ7 to DQ0) Addr. = VA DQ7 = Data? No No DQ5 = 1? Yes Read Byte (DQ7 to DQ0) Addr. = VA Yes VA = Byte address for programming = Any of the sector addresses within the sector being erased during sector erase or multiple sector erases operation = Any of the sector addresses within the sector not being protected during chip erase operation DQ7 = Data? * No Fail Yes Pass * : DQ7 is rechecked even if DQ5 = “1” because DQ7 may change simultaneously with DQ5. 44 MBM29LV400TC-55/70/90/MBM29LV400BC-55/70/90 4. Toggle Bit Algorithm Start Read (DQ7 to DQ0) Addr. = "H" or "L" *1 Read (DQ7 to DQ0) Addr. = "H" or "L" DQ6 = Toggle ? Yes No DQ5 = 1? Yes Read DQ7 to DQ0 Twice Addr. = "H" or "L" No *1, *2 DQ6 = Toggle ? Yes Program/Erase Operation Not Complete. Write Reset Command No Program/Erase Operation Complete *1 : Read toggle bit twice to determine whether it is toggling. *2 : Recheck toggle bit because it may stop toggling as DQ5 changes to “1” . 45 MBM29LV400TC-55/70/90/MBM29LV400BC-55/70/90 5. Sector Protection Algorithm Start Setup Sector Addr. (A17, A16, A15, A14, A13, A12) PLSCNT = 1 OE = VID, A9 = VID, CE = VIL, RESET = VIH A6 = A0 = VIL, A1 = VIH Activate WE Pulse Increment PLSCNT Time out 100 µs WE = VIH, CE = OE = VIL (A9 should remain VID) ( No No PLSCNT = 25? Yes Remove VID from A9 Write Reset Command Read from Sector Addr. = SPA, A1 = VIH, * A6 = A0 = VIL ) Data = 01h? Yes Yes Protect Another Sector? No Device Failed Remove VID from A9 Write Reset Command Sector Protection Completed *: A-1 is V IL on byte mode. 46 MBM29LV400TC-55/70/90/MBM29LV400BC-55/70/90 6. Temporary Sector Unprotection Algorithm Start RESET = VID *1 Perform Erase or Program Operations RESET = VIH Temporary Sector Unprotection Completed *2 *1: All protected sectors are unprotected. *2: All previously protected sectors are protected once again. 47 MBM29LV400TC-55/70/90/MBM29LV400BC-55/70/90 7. Extended Sector Protection Algorithm Start RESET = VID Wait to 4 µs Device is Operating in Temporary Sector Unprotection Mode No Extended Sector Protection Entry? Yes To Setup Sector Protection Write XXXh/60h PLSCNT = 1 To Protect Sector Write SPA/60h to Sector Address (A6 = A0 = VIL, A1 = VIH) Increment PLSCNT Time Out 150 µs To Verify Sector Protection Write SPA/40h to Sector Address Setup Next Sector Address (A6 = A0 = VIL, A1 = VIH) Read from Sector Address (Addr. = SPA, A1 = VIH, A6 = A0 = VIL) No No PLSCNT = 25? Yes Remove VID from RESET Write Reset Command Data = 01h? Yes Protection Other Sector ? No Remove VID from RESET Write Reset Command Yes Device Failed Sector Protection Completed 48 MBM29LV400TC-55/70/90/MBM29LV400BC-55/70/90 8. Embedded ProgramTM Algorithm for Fast Mode FAST MODE ALGORITHM Start 555h/AAh 2AAh/55h Set Fast Mode 555h/20h XXXh/A0h Program Address/Program Data Data Polling Verify Data? Yes No No In Fast Program Increment Address Last Address ? Yes Programming Completed XXXh/90h Reset Fast Mode XXXh/F0h Notes : • The sequence is applied for × 16 mode. • The addresses differ from × 8 mode. 49 MBM29LV400TC-55/70/90/MBM29LV400BC-55/70/90 s ORDERING INFORMATION Part No. MBM29LV400TC-55PF MBM29LV400TC-70PF MBM29LV400TC-90PF MBM29LV400TC-55PFTN MBM29LV400TC-70PFTN MBM29LV400TC-90PFTN MBM29LV400TC-55PFTR MBM29LV400TC-70PFTR MBM29LV400TC-90PFTR MBM29LV400TC-55PCV MBM29LV400TC-70PCV MBM29LV400TC-90PCV MBM29LV400TC-55PBT MBM29LV400TC-70PBT MBM29LV400TC-90PBT MBM29LV400TC-55PW MBM29LV400TC-70PW MBM29LV400TC-90PW MBM29LV400BC-55PF MBM29LV400BC-70PF MBM29LV400BC-90PF MBM29LV400BC-55PFTN MBM29LV400BC-70PFTN MBM29LV400BC-90PFTN MBM29LV400BC-55PFTR MBM29LV400BC-70PFTR MBM29LV400BC-90PFTR MBM29LV400BC-55PCV MBM29LV400BC-70PCV MBM29LV400BC-90PCV MBM29LV400BC-55PBT MBM29LV400BC-70PBT MBM29LV400BC-90PBT MBM29LV400BC-55PW MBM29LV400BC-70PW MBM29LV400BC-90PW Package 44-pin plastic SOP (FPT-44P-M16) 48-pin plastic TSOP (1) (FPT-48P-M19) (Normal Bend) 48-pin plastic TSOP (1) (FPT-48P-M20) (Reverse Bend) 48-pin plastic CSOP (LCC-48P-M03) 48-pin plastic FBGA (BGA-48P-M11) 48-pin plastic SCSP (WLP-48P-M02) 44-pin plastic SOP (FPT-44P-M16) 48-pin plastic TSOP (1) (FPT-48P-M19) (Normal Bend) 48-pin plastic TSOP (1) (FPT-48P-M20) (Reverse Bend) 48-pin plastic CSOP (LCC-48P-M03) 48-pin plastic FBGA (BGA-48P-M11) 48-pin plastic SCSP (WLP-48P-M02) Access Time 55 70 90 55 70 90 55 70 90 55 70 90 55 70 90 55 70 90 55 70 90 55 70 90 55 70 90 55 70 90 55 70 90 55 70 90 Sector Architecture Remarks Top Sector Bottom Sector 50 MBM29LV400TC-55/70/90/MBM29LV400BC-55/70/90 MBM29LV400 T C -55 PFTN PACKAGE TYPE PFTN = 48-Pin Thin Small Outline Package (TSOP) Normal Bend PFTR = 48-Pin Thin Small Outline Package (TSOP) Reverse Bend PF = 44-Pin Small Outline Package PCV = 48-Pin C- leaded Small Outline Package (CSOP) PBT = 48-Ball Fine Pitch Ball Grid Array Package (FBGA) PW = 48-Ball Super Chip Size Package (SCSP) SPEED OPTION See Product Selector Guide Device Revision BOOT CODE SECTOR ARCHITECTURE T = Top sector B = Bottom sector DEVICE NUMBER/DESCRIPTION MBM29LV400 4Mega-bit (512K × 8-Bit or 256K × 16-Bit) CMOS Flash Memory 3.0 V-only Read, Program, and Erase 51 MBM29LV400TC-55/70/90/MBM29LV400BC-55/70/90 s PACKAGE DIMENSIONS 44-pin plastic SOP (FPT-44P-M16) Note 1) *1 : These dimensions include resin protrusion. Note 2) *2 : These dimensions do not include resin protrusion. Note 3) Pins width and pins thickness include plating thickness. Note 4) Pins width do not include tie bar cutting remainder. +0.25 +.010 *1 28.45 –0.20 1.120 –.008 44 0.17 –0.04 .007 –.002 23 +0.03 +.001 16.00±0.20 (.630±.008) *2 13.00±0.10 (.512±.004) INDEX Details of "A" part 2.35±0.15 (Mounting height) (.093±.006) 0.25(.010) 1 22 +0.08 +.0031 "A" 0~8˚ 1.27(.050) 0.42 –0.07 .017 –.0028 0.13(.005) M 0.80±0.20 (.031±.008) 0.88±0.15 (.035±.006) 0.20 –0.15 +0.10 +.004 .008 –.006 (Stand off) 0.10(.004) C 2002 FUJITSU LIMITED F44023S-c-6-6 Dimensions in mm (inches). Note: The values in parentheses are reference values. (Continued) 52 MBM29LV400TC-55/70/90/MBM29LV400BC-55/70/90 48-pin plastic TSOP(1) (FPT-48P-M19) Note 1) * : Values do not include resin protrusion. Resin protrusion and gate protrusion are + 0.15 (.006) Max (each side) . Note 2) Pins width and pins thickness include plating thickness. Note 3) Pins width do not include tie bar cutting remainder. 48 LEAD No. 1 INDEX Details of "A" part 0.25(.010) 0~8˚ 0.60±0.15 (.024±.006) 24 25 20.00±0.20 (.787±.008) * 18.40±0.20 (.724±.008) * 12.00±0.20 (.472±.008) 1.10 –0.05 +0.10 +.004 .043 –.002 (Mounting height) 0.50(.020) "A" 0.10(.004) 0.17 –0.08 .007 –.003 C +0.03 +.001 0.10±0.05 (.004±.002) (Stand off height) 0.22±0.05 (.009±.002) 0.10(.004) M 2003 FUJITSU LIMITED F48029S-c-6-7 Dimensions in mm (inches). Note: The values in parentheses are reference values. (Continued) 53 MBM29LV400TC-55/70/90/MBM29LV400BC-55/70/90 48-pin plastic TSOP(1) (FPT-48P-M20) Note 1) * : Values do not include resin protrusion. Resin protrusion and gate protrusion are + 0.15 (.006) Max (each side) . Note 2) Pins width and pins thickness include plating thickness. Note 3) Pins width do not include tie bar cutting remainder. 48 LEAD No. 1 INDEX Details of "A" part 0.60±0.15 (.024±.006) 0~8˚ 0.25(.010) 24 25 0.17 –0.08 +0.03 +.001 0.10(.004) .007 –.003 0.50(.020) 0.22±0.05 (.009±.002) 0.10(.004) M 0.10±0.05 (.004±.002) (Stand off height) "A" 1.10 –0.05 +0.10 +.004 * 18.40±0.20 (.724±.008) 20.00±0.20 (.787±.008) .043 –.002 (Mounting height) * 12.00±0.20(.472±.008) C 2003 FUJITSU LIMITED F48030S-c-6-7 Dimensions in mm (inches). Note: The values in parentheses are reference values. (Continued) 54 MBM29LV400TC-55/70/90/MBM29LV400BC-55/70/90 Note 1) *1 : Resin protrusion. (Each side : +0.15 (.006) Max) . Note 2) *2 : These dimensions do not include resin protrusion. Note 3) Pins width and pins thickness include plating thickness. Note 4) Pins width do not include tie bar cutting remainder. 25 48-pin plastic CSOP (LCC-48P-M03) 48 "A" 10.00±0.20 (.394±.008) *2 9.50±0.10 (.374±.004) INDEX INDEX 0.05 –0 +0.05 +.002 .002 –.0 (Stand off) LEAD No. 1 24 *1 10.00±0.10(.394±.004) 0.95±0.05(.037±.002) (Mounting height) 0.22±0.035 (.009±.001) Details of "A" part 0˚~10˚ 0.65(.026) 1.15(.045) 0.40(.016) 9.20(.362)REF 0.08(.003) C 2003 FUJITSU LIMITED C48056S-c-2-2 Dimensions in mm (inches). Note: The values in parentheses are reference values. (Continued) 55 MBM29LV400TC-55/70/90/MBM29LV400BC-55/70/90 48-ball plastic FBGA (BGA-48P-M11) 8.00±0.20(.315±.008) 1.05 –0.10 .041 –.004 (Mounting height) 0.38±0.10(.015±.004) (Stand off) +0.15 +.006 (5.60(.220)) 0.80(.031)TYP 6 5 INDEX 6.00±0.20 (.236±.008) 4 (4.00(.157)) 3 2 1 H C0.25(.010) G F E D C B A M 48-ø0.45±0.10 (48-ø.018±.004) ø0.08(.003) 0.10(.004) C 2001 FUJITSU LIMITED B48011S-c-5-3 Dimensions in mm (inches). Note: The values in parentheses are reference values. (Continued) 56 MBM29LV400TC-55/70/90/MBM29LV400BC-55/70/90 (Continued) 48-pin plastic SCSP (WLP-48P-M02) (3.50=0.50x7) ((.138=.020x7)) Y 0.50(.020) TYP 4.67±0.10(.184±.004) 3.52±0.10 (.139±.004) (2.50=0.50x5) ((.098=.020x5)) INDEX AREA (LASER MARKING) X 0.50(.020) TYP 4-Ø0.13(4-Ø.005) 1.00(.039) Max. 48-Ø0.35±0.10 (48-Ø.014±.004) 0.08(.003) M XYZ Z 0.10(.004) Z 0.25(.010) Min. (Stand off) C 2001 FUJITSU LIMITED W48002S-c-1-1 Dimensions in mm (inches). Note: The values in parentheses are reference values. 57 MBM29LV400TC-70/90/12/MBM29LV400BC-70/90/12 FUJITSU LIMITED All Rights Reserved. The contents of this document are subject to change without notice. Customers are advised to consult with FUJITSU sales representatives before ordering. The information, such as descriptions of function and application circuit examples, in this document are presented solely for the purpose of reference to show examples of operations and uses of Fujitsu semiconductor device; Fujitsu does not warrant proper operation of the device with respect to use based on such information. When you develop equipment incorporating the device based on such information, you must assume any responsibility arising out of such use of the information. Fujitsu assumes no liability for any damages whatsoever arising out of the use of the information. Any information in this document, including descriptions of function and schematic diagrams, shall not be construed as license of the use or exercise of any intellectual property right, such as patent right or copyright, or any other right of Fujitsu or any third party or does Fujitsu warrant non-infringement of any third-party’s intellectual property right or other right by using such information. Fujitsu assumes no liability for any infringement of the intellectual property rights or other rights of third parties which would result from the use of information contained herein. The products described in this document are designed, developed and manufactured as contemplated for general use, including without limitation, ordinary industrial use, general office use, personal use, and household use, but are not designed, developed and manufactured as contemplated (1) for use accompanying fatal risks or dangers that, unless extremely high safety is secured, could have a serious effect to the public, and could lead directly to death, personal injury, severe physical damage or other loss (i.e., nuclear reaction control in nuclear facility, aircraft flight control, air traffic control, mass transport control, medical life support system, missile launch control in weapon system), or (2) for use requiring extremely high reliability (i.e., submersible repeater and artificial satellite). Please note that Fujitsu will not be liable against you and/or any third party for any claims or damages arising in connection with above-mentioned uses of the products. Any semiconductor devices have an inherent chance of failure. You must protect against injury, damage or loss from such failures by incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and prevention of over-current levels and other abnormal operating conditions. If any products described in this document represent goods or technologies subject to certain restrictions on export under the Foreign Exchange and Foreign Trade Law of Japan, the prior authorization by Japanese government will be required for export of those products from Japan. F0309 © FUJITSU LIMITED Printed in Japan