S29GL01GP12TAI023

S29GL-P MirrorBitTM Flash Family S29GL01GP, S29GL512P, S29GL256P, S29GL128P 1 Gigabit, 512 Megabit , 256 Megabit and 128 Megabit 3.0 Volt-only Page Mode Flash Memory featuring 90 nm MirrorBit Process Technology S29GL-P MirrorBitTM Flash Family Cover Sheet Data Sheet (Advance Information) Notice to Readers: This document contains information on one or more products under development at Spansion Inc. The information is intended to help you evaluate this product. Do not design in this product without contacting the factory. Spansion Inc. reserves the right to change or discontinue work on this proposed product without notice. Publication Number S29GL-P_00 Revision A Amendment 3 Issue Date November 21, 2006 Data Sheet (Advance Information) Notice On Data Sheet Designations Spansion Inc. issues data sheets with Advance Information or Preliminary designations to advise readers of product information or intended specifications throughout the product life cycle, including development, qualification, initial production, and full production. In all cases, however, readers are encouraged to verify that they have the latest information before finalizing their design. The following descriptions of Spansion data sheet designations are presented here to highlight their presence and definitions. Advance Information The Advance Information designation indicates that Spansion Inc. is developing one or more specific products, but has not committed any design to production. Information presented in a document with this designation is likely to change, and in some cases, development on the product may discontinue. Spansion Inc. therefore places the following conditions upon Advance Information content: “This document contains information on one or more products under development at Spansion Inc. The information is intended to help you evaluate this product. Do not design in this product without contacting the factory. Spansion Inc. reserves the right to change or discontinue work on this proposed product without notice.” Preliminary The Preliminary designation indicates that the product development has progressed such that a commitment to production has taken place. This designation covers several aspects of the product life cycle, including product qualification, initial production, and the subsequent phases in the manufacturing process that occur before full production is achieved. Changes to the technical specifications presented in a Preliminary document should be expected while keeping these aspects of production under consideration. Spansion places the following conditions upon Preliminary content: “This document states the current technical specifications regarding the Spansion product(s) described herein. The Preliminary status of this document indicates that product qualification has been completed, and that initial production has begun. Due to the phases of the manufacturing process that require maintaining efficiency and quality, this document may be revised by subsequent versions or modifications due to changes in technical specifications.” Combination Some data sheets contain a combination of products with different designations (Advance Information, Preliminary, or Full Production). This type of document distinguishes these products and their designations wherever necessary, typically on the first page, the ordering information page, and pages with the DC Characteristics table and the AC Erase and Program table (in the table notes). The disclaimer on the first page refers the reader to the notice on this page. Full Production (No Designation on Document) When a product has been in production for a period of time such that no changes or only nominal changes are expected, the Preliminary designation is removed from the data sheet. Nominal changes may include those affecting the number of ordering part numbers available, such as the addition or deletion of a speed option, temperature range, package type, or VIO range. Changes may also include those needed to clarify a description or to correct a typographical error or incorrect specification. Spansion Inc. applies the following conditions to documents in this category: “This document states the current technical specifications regarding the Spansion product(s) described herein. Spansion Inc. deems the products to have been in sufficient production volume such that subsequent versions of this document are not expected to change. However, typographical or specification corrections, or modifications to the valid combinations offered may occur.” Questions regarding these document designations may be directed to your local sales office. ii S29GL-P MirrorBitTM Flash Family S29GL-P_00_A3 November 21, 2006 S29GL-P MirrorBitTM Flash Family S29GL01GP, S29GL512P, S29GL256P, S29GL128P 1 Gigabit, 512 Megabit , 256 Megabit and 128 Megabit 3.0 Volt-only Page Mode Flash Memory featuring 90 nm MirrorBit Process Technology Data Sheet (Advance Information) General Description The Spansion S29GL01G/512/256/128P are Mirrorbit™ Flash products fabricated on 90 nm process technology. These devices offer a fast page access time of 25 ns with a corresponding random access time of 110 ns. They feature a Write Buffer that allows a maximum of 32 words/64 bytes to be programmed in one operation, resulting in faster effective programming time than standard programming algorithms. This makes these devices ideal for today’s embedded applications that require higher density, better performance and lower power consumption. Distinctive Characteristics Single 3V read/program/erase (2.7-3.6 V) Enhanced VersatileI/O™ control – All input levels (address, control, and DQ input levels) and outputs are determined by voltage on VIO input. VIO range is 1.65 to VCC Offered Packages – 56-pin TSOP – 64-ball Fortified BGA 90 nm MirrorBit process technology 8-word/16-byte page read buffer 32-word/64-byte write buffer reduces overall programming time for multiple-word updates Secured Silicon Sector region – 128-word/256-byte sector for permanent, secure identification through an 8-word/16-byte random Electronic Serial Number – Can be programmed and locked at the factory or by the customer Suspend and Resume commands for Program and Erase operations Write operation status bits indicate program and erase operation completion Unlock Bypass Program command to reduce programming time Support for CFI (Common Flash Interface) Persistent and Password methods of Advanced Sector Protection WP#/ACC input – Accelerates programming time (when VACC is applied) for greater throughput during system production – Protects first or last sector regardless of sector protection settings Uniform 64Kword/128KByte Sector Architecture – – – – S29GL01GP: One thousand twenty-four sectors S29GL512P: Five hundred twelve sectors S29GL256P: Two hundred fifty-six sectors S29GL128P: One hundred twenty-eight sectors Hardware reset input (RESET#) resets device Ready/Busy# output (RY/BY#) detects program or erase cycle completion 100,000 erase cycles per sector typical 20-year data retention typical Performance Characteristics Max. Read Access Times (ns)* 512/256/128 Mb** Parameter Random Access Time (tACC) Page Access Time (tPACC) CE# Access Time (tCE) OE# Access Time (tOE) V1 100 25 110 25 V2 110 25 110 25 V3 120 25 120 30 V1 110 25 110 25 1 Gb V2 120 25 120 25 V3 130 25 130 30 Program & Erase Times (typical values) Single Word Programming Effective Write Buffer Programming (VCC) Per Word Effective Write Buffer Programming (VACC) Per Word Sector Erase Time (64 Kword Sector) 60 µs 15 µs 15 µs 0.5 s Current Consumption (typical values) Random Access Read 8-Word Page Read Program/Erase Standby 30 mA 1 mA 50 mA 1 µA * Access times are dependent on VCC and VIO operating ranges. See Ordering Information page for further details. V1: VCC = 3.0–3.6 V. V2: VCC = VIO = 2.7–3.6 V. V3: VIO = 1.65–VCC, VCC = 3 V. ** Contact a sales representative for availability. Publication Number S29GL-P_00 Revision A Amendment 3 Issue Date November 21, 2006 This document contains information on one or more products under development at Spansion Inc. The information is intended to help you evaluate this product. Do not design in this product without contacting the factory. Spansion Inc. reserves the right to change or discontinue work on this proposed product without notice. Data Sheet (Advance Information) Table of Contents General Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Distinctive Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Performance Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 List of Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 List of Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1. 2. 3. 4. Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 1.1 Recommended Combinations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Input/Output Descriptions & Logic Symbol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Physical Dimensions/Connection Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 4.1 Related Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 4.2 Special Handling Instructions for BGA Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 4.3 LAA064—64 ball Fortified Ball Grid Array, 11 x 13 mm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 4.4 TS056—56-Pin Standard Thin Small Outline Package (TSOP) . . . . . . . . . . . . . . . . . . . . . . 11 Additional Resources. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.1 Application Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.2 Specification Bulletins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.3 Hardware and Software Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.4 Contacting Spansion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 12 12 12 12 5. 6. 7. Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 6.1 Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Device Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.1 Device Operation Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.2 Word/Byte Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.3 VersatileIOTM (VIO) Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.4 Read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.5 Page Read Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.6 Autoselect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.7 Program/Erase Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.8 Write Operation Status. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.9 Writing Commands/Command Sequences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Advanced Sector Protection/Unprotection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.1 Lock Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.2 Persistent Protection Bits. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.3 Persistent Protection Bit Lock Bit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.4 Password Protection Method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.5 Advanced Sector Protection Software Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.6 Hardware Data Protection Methods. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Power Conservation Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.1 Standby Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.2 Automatic Sleep Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.3 Hardware RESET# Input Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.4 Output Disable (OE#). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Secured Silicon Sector Flash Memory Region . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.1 Factory Locked Secured SiliconSector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.2 Customer Lockable Secured Silicon Sector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.3 Secured Silicon Sector Entry/Exit Command Sequences . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 14 15 15 15 15 16 19 31 35 37 38 38 40 40 43 43 44 44 44 44 44 45 45 45 46 8. 9. 10. 11. Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 11.1 Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 2 S29GL-P MirrorBitTM Flash Family S29GL-P_00_A3 November 21, 2006 Data Sheet (Advance Information) 11.2 11.3 11.4 11.5 11.6 11.7 12. Operating Ranges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Test Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Key to Switching Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Switching Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 48 49 49 50 51 Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 12.1 Command Definitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 12.2 Common Flash Memory Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 Revision Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 13. List of Figures Figure 3.1 Figure 4.1 Figure 4.2 Figure 4.3 Figure 6.1 Figure 7.1 Figure 7.2 Figure 7.3 Figure 7.4 Figure 8.1 Figure 8.2 Figure 8.3 Figure 11.1 Figure 11.2 Figure 11.3 Figure 11.4 Figure 11.5 Figure 11.6 Figure 11.7 Figure 11.8 Figure 11.9 Figure 11.10 Figure 11.11 Figure 11.12 Figure 11.13 Figure 11.14 Figure 11.15 S29GL-P Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 64-ball Fortified Ball Grid Array . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 LAA064—64ball Fortified Ball Grid Array (FBGA), 11 x 13 mm . . . . . . . . . . . . . . . . . . . . . . . .9 56-Pin Thin Small Outline Package (TSOP), 14 x 20 mm . . . . . . . . . . . . . . . . . . . . . . . . . . .11 S29GL01GP Sector & Memory Address Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Single Word Program. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Write Buffer Programming Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 Sector Erase Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Write Operation Status Flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32 Advanced Sector Protection/Unprotection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37 PPB Program/Erase Algorithm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39 Lock Register Program Algorithm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42 Maximum Negative Overshoot Waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Maximum Positive Overshoot Waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Test Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Input Waveforms and Measurement Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Read Operation Timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 Page Read Timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52 Reset Timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Power-up Sequence Timings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Program Operation Timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55 Accelerated Program Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55 Chip/Sector Erase Operation Timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56 Data# Polling Timings (During Embedded Algorithms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56 Toggle Bit Timings (During Embedded Algorithms) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57 DQ2 vs. DQ6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 Alternate CE# Controlled Write (Erase/Program) Operation Timings . . . . . . . . . . . . . . . . . . 59 List of Tables Table 2.1 Table 6.1 Table 6.2 Table 6.3 Table 7.1 Table 7.2 Table 7.3 Table 7.4 Table 7.5 Input/Output Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 S29GL512P Sector & Memory Address Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 S29GL256P Sector & Memory Address Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 S29GL128P Sector & Memory Address Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 Device Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 Autoselect Codes, (High Voltage Method) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 Autoselect Addresses in System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 Autoselect Entry in System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 Autoselect Exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 November 21, 2006 S29GL-P_00_A3 S29GL-P MirrorBitTM Flash Family 3 Data Sheet (Advance Information) Table 7.6 Table 7.7 Table 7.8 Table 7.9 Table 7.10 Table 7.11 Table 7.12 Table 7.13 Table 7.14 Table 7.15 Table 7.16 Table 7.17 Table 7.18 Table 8.1 Table 8.2 Table 10.1 Table 10.2 Table 10.3 Table 10.4 Table 11.1 Table 11.2 Table 11.3 Table 11.4 Table 11.5 Table 11.6 Table 11.7 Table 11.8 Table 12.1 Table 12.2 Table 12.3 Table 12.4 Table 12.5 Table 12.6 Table 12.7 Table 12.8 Single Word/Byte Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 Write Buffer Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 Sector Erase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 Chip Erase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27 Erase Suspend . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 Erase Resume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 Program Suspend . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 Program Resume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 Unlock Bypass Entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 Unlock Bypass Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 Unlock Bypass Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 Write Operation Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35 Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36 Lock Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38 Sector Protection Schemes: DYB, PPB and PPB Lock Bit Combinations . . . . . . . . . . . . . . .43 Secured Silicon Sector Addresses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45 Secured Silicon Sector Entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46 Secured Silicon Sector Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46 Secured Silicon Sector Exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47 Test Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49 S29GL-P DC Characteristics (CMOS Compatible) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50 S29GL-P Read-Only Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51 Hardware Reset (RESET#) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52 Power-up Sequence Timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53 S29GL-P Erase and Program Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54 S29GL-P Alternate CE# Controlled Erase and Program Operations . . . . . . . . . . . . . . . . . . .58 Erase And Programming Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60 S29GL-P Memory Array Command Definitions, x16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61 S29GL-P Sector Protection Command Definitions, x16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63 S29GL-P Memory Array Command Definitions, x8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64 S29GL-P Sector Protection Command Definitions, x8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65 CFI Query Identification String . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66 System Interface String . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67 Device Geometry Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67 Primary Vendor-Specific Extended Query . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68 4 S29GL-P MirrorBitTM Flash Family S29GL-P_00_A3 November 21, 2006 Data Sheet (Advance Information) 1. Ordering Information The ordering part number is formed by a valid combination of the following: S29GL01GP S29GL512P S29GL256P S29GL128P 10 F A I 01 0 PACKING TYPE 0 = Tray (standard; see (Note 1) 2 = 7” Tape and Reel 3 = 13” Tape and Reel MODEL NUMBER (VIO range, protection when WP# =VIL) 01 = VIO = VCC = 2.7 to 3.6 V, highest address sector protected 02 = VIO = VCC = 2.7 to 3.6 V, lowest address sector protected V1 = VIO = 1.65 to VCC, VCC = 2.7 to 3.6 V, highest address sector protected V2 = VIO = 1.65 to VCC, VCC = 2.7 to 3.6 V, lowest address sector protected R1 = VIO = VCC = 3.0 to 3.6 V, highest address sector protected R2 = VIO = VCC = 3.0 to 3.6 V, lowest address sector protected TEMPERATURE RANGE I = Industrial (–40°C to +85°C) PACKAGE MATERIALS SET A = Pb (Note 4) F = Pb-free PACKAGE TYPE T = Thin Small Outline Package (TSOP) Standard Pinout F = Fortified Ball Grid Array, 1.0 mm pitch package SPEED OPTION 11 = 110 ns 12 = 120 ns 13 = 130 ns DEVICE NUMBER/DESCRIPTION S29GL01GP, S29GL512P, S29GL256P, S29GL128P 3.0 Volt-only, 1024, 512, 256 and 128 Megabit (32 M x 16-Bit/64 M x 8-Bit) Page-Mode Flash Memory Manufactured on 90 nm MirrorBitTM process technology S29GL-P Valid Combinations 1 Gb Speed (ns) 11 12 13 S29GL01GP 11 12 13 S29GL512P, S29GL256P, S29GL128P Notes 1. Type 0 is standard. Specify other options as required. 2. TSOP package marking omits packing type designator from ordering part number. 3. BGA package marking omits leading “S29” and packing type designator from ordering part number. 4. Contact local sales representative for availability, and on the following part numbers: S29GL01GP12TFI010, S29GL01GP12FFI010, S29GL01GP13TFIV10, S29GL01GP13FFIV10. (Note 4) FAI , FFI (Note 4) R1, R2 01 (Note 4), 02 V1 (Note 4), V2 0, 2, 3 (Note 1) LAA064 (Fortified BGA) (Note 3) TAI , TFI (Note 4) Package & Temperature Model Number R1, R2 01 (Note 4), 02 V1 (Note 4), V2 0, 3 (Note 1) TS056 (TSOP) (Note 2) Pack Type Package Description 1.1 Recommended Combinations Recommended Combinations list configurations planned to be supported in volume for this device. Consult your local sales office to confirm availability of specific recommended combinations and to check on newly released combinations. November 21, 2006 S29GL-P_00_A3 S29GL-P MirrorBitTM Flash Family 5 Data Sheet (Advance Information) 2. Input/Output Descriptions & Logic Symbol Table 2.1 identifies the input and output package connections provided on the device. Table 2.1 Input/Output Descriptions Symbol Type Address lines for GL01GP A24–A0 for GL512P A23–A0 for GL256P, A22–A0 for GL128P. Data input/output. DQ15: Data input/output in word mode . A-1: LSB address input in byte mode. Chip Enable. Output Enable. Write Enable. Device Power Supply. Versatile IO Input. Ground. Not connected internally. Ready/Busy. Indicates whether an Embedded Algorithm is in progress or complete. At VIL, the device is actively erasing or programming. At High Z, the device is in ready. Selects data bus width. At VIL, the device is in byte configuration and data I/O pins DQ0DQ7 are active. At VIH, the device is in word configuration and data I/O pins DQ0-DQ15 are active. Hardware Reset. Low = device resets and returns to reading array data. Write Protect/Acceleration Input. At VIL, disables program and erase functions in the outermost sectors. At VHH, accelerates programming; automatically places device in unlock bypass mode. Should be at VIH for all other conditions. Reserved for future use. Description A25–A0 Input DQ14–DQ0 DQ15 CE# OE# WE# VCC VIO VSS NC RY/BY# I/O I/O Input Input Input Supply Supply Supply No Connect Output BYTE# RESET# WP#/ACC RFU Input Input Input Reserved 6 S29GL-P MirrorBitTM Flash Family S29GL-P_00_A3 November 21, 2006 Data Sheet (Advance Information) 3. Block Diagram Figure 3.1 S29GL-P Block Diagram RY/BY# DQ15–DQ0 (A-1) Sector Switches VCC VSS VIO RESET# Erase Voltage Generator Input/Output Buffers WE# WP#/ACC BYTE# State Control Command Register PGM Voltage Generator Chip Enable Output Enable Logic STB Data Latch CE# OE# Y-Decoder STB Y-Gating VCC Detector Timer Address Latch X-Decoder Cell Matrix AMax**–A0 ** AMax GL01GP=A25, AMax GL512P = A24, AMax GL256P = A23, AMax GL128P = A22 4. Physical Dimensions/Connection Diagrams This section shows the I/O designations and package specifications for the S29GL-P. 4.1 Related Documents The following documents contain information relating to the S29GL-P devices. Click on the title or go to www.spansion.com download the PDF file, or request a copy from your sales office. Considerations for X-ray Inspection of Surface-Mounted Flash Integrated Circuits 4.2 Special Handling Instructions for BGA Package Special handling is required for Flash Memory products in BGA packages. Flash memory devices in BGA packages may be damaged if exposed to ultrasonic cleaning m ethods. The package and/or data integrity may be compromised if the package body is exposed to temperatures above 150°C for prolonged periods of time. November 21, 2006 S29GL-P_00_A3 S29GL-P MirrorBitTM Flash Family 7 Data Sheet (Advance Information) Figure 4.1 64-ball Fortified Ball Grid Array 64-ball Fortified BGA Top View, Balls Facing Down RFU on S29GL128P RFU on S29GL256P RFU on S29GL512P A8 RFU A7 A13 A6 A9 A5 WE# A4 B8 A22 B7 A12 B6 A8 B5 RESET# B4 C8 A23 C7 A14 C6 A10 C5 A21 C4 A18 C3 A6 C2 A2 C1 RFU D8 VIO D7 A15 D6 A11 D5 A19 D4 A20 D3 A5 D2 A1 D1 RFU E8 VSS E7 A16 E6 DQ7 E5 DQ5 E4 DQ2 E3 DQ0 E2 A0 E1 RFU F8 A24 F7 BYTE# F6 DQ14 F5 DQ12 F4 DQ10 F3 DQ8 F2 CE# F1 VIO G8 A25 G7 DQ15/A-1 G6 DQ13 G5 VCC G4 DQ11 G3 DQ9 G2 OE# G1 RFU H8 RFU H7 VSS H6 DQ6 H5 DQ4 H4 DQ3 H3 DQ1 H2 VSS H1 RFU RY/BY# WP#/ACC A3 A7 A2 A3 A1 RFU B3 A17 B2 A4 B1 RFU Do not connect to VSS. 8 S29GL-P MirrorBitTM Flash Family S29GL-P_00_A3 November 21, 2006 Data Sheet (Advance Information) 4.3 LAA064—64 ball Fortified Ball Grid Array, 11 x 13 mm Figure 4.2 LAA064—64ball Fortified Ball Grid Array (FBGA), 11 x 13 mm November 21, 2006 S29GL-P_00_A3 S29GL-P MirrorBitTM Flash Family 9 Data Sheet (Advance Information) NC on S29GL128P NC on S29GL256P NC on S29GL512P A23 A22 A15 A14 A13 A12 A11 A10 A9 A8 A19 A20 WE# RESET# A21 WP#/ACC RY/BY# A18 A17 A7 A6 A5 A4 A3 A2 A1 RFU RFU 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 56-Pin Standard TSOP (Top View) 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 A24 A25 A16 BYTE# VSS DQ15/A-1 DQ7 DQ14 DQ6 DQ13 DQ5 DQ12 DQ4 VCC DQ11 DQ3 DQ10 DQ2 DQ9 DQ1 DQ8 DQ0 OE# VSS CE# A0 Do not connect to VSS. RFU VIO 10 S29GL-P MirrorBitTM Flash Family S29GL-P_00_A3 November 21, 2006 Data Sheet (Advance Information) 4.4 TS056—56-Pin Standard Thin Small Outline Package (TSOP) Figure 4.3 56-Pin Thin Small Outline Package (TSOP), 14 x 20 mm PACKAGE JEDEC SYMBOL A A1 A2 b1 b c1 c D D1 E e L O TS 56 MO-142 (B) EC MIN. --0.05 0.95 0.17 0.17 0.10 0.10 19.80 18.30 13.90 0.50 0˚ 0.08 NOM. ----1.00 0.20 0.22 ----20.00 18.40 14.00 0.50 BASIC 0.60 --56 0.70 8˚ 0.20 MAX. 1.20 0.15 1.05 0.23 0.27 0.16 0.21 20.20 18.50 14.10 NOTES: 1 2 3 CONTROLLING DIMENSIONS ARE IN MILLIMETERS (mm). (DIMENSIONING AND TOLERANCING CONFORMS TO ANSI Y14.5M-1982.) PIN 1 IDENTIFIER FOR STANDARD PIN OUT (DIE UP). TO BE DETERMINED AT THE SEATING PLANE -C- . THE SEATING PLANE IS DEFINED AS THE PLANE OF CONTACT THAT IS MADE WHEN THE PACKAGE LEADS ARE ALLOWED TO REST FREELY ON A FLAT HORIZONTAL SURFACE. DIMENSIONS D1 AND E DO NOT INCLUDE MOLD PROTRUSION. ALLOWABLE MOLD PROTUSION IS 0.15 mm PER SIDE. DIMENSION b DOES NOT INCLUDE DAMBAR PROTUSION. ALLOWABLE DAMBAR PROTUSION SHALL BE 0.08 mm TOTAL IN EXCESS OF b DIMENSION AT MAX MATERIAL CONDITION. MINIMUM SPACE BETWEEN PROTRUSION AND AN ADJACENT LEAD TO BE 0.07 mm. THESE DIMESIONS APPLY TO THE FLAT SECTION OF THE LEAD BETWEEN 0.10 mm AND 0.25 mm FROM THE LEAD TIP. LEAD COPLANARITY SHALL BE WITHIN 0.10 mm AS MEASURED FROM THE SEATING PLANE. DIMENSION "e" IS MEASURED AT THE CENTERLINE OF THE LEADS. 4 5 6 7 8 R N 3160\38.10A November 21, 2006 S29GL-P_00_A3 S29GL-P MirrorBitTM Flash Family 11 Data Sheet (Advance Information) 5. Additional Resources Visit www.spansion.com to obtain the following related documents: 5.1 Application Notes The following is a list of application notes related to this product. All Spansion application notes are available at http://www.spansion.com/support/technical_documents/application_notes.html Using the Operation Status Bits in AMD Devices Understanding Page Mode Flash Memory Devices MirrorBit™ Flash Memory Write Buffer Programming and Page Buffer Read Common Flash Interface Version 1.4 Vendor Specific Extensions 5.2 Specification Bulletins Contact your local sales office for details. 5.3 Hardware and Software Support Downloads and related information on Flash device support is available at www.spansion.com/support/index.html Spansion low-level drivers Enhanced Flash drivers Flash file system Downloads and related information on simulation modeling and CAD modeling support is available at http:// www.spansion.com/support/simulation_models.html VHDL and Verilog IBIS ORCAD An FAQ (Frequently Asked Questions) list is available at www.spansion.com/support/ses/index.html 5.4 Contacting Spansion Obtain the latest list of company locations and contact information on our web site at www.spansion.com/about/location.html 12 S29GL-P MirrorBitTM Flash Family S29GL-P_00_A3 November 21, 2006 Data Sheet (Advance Information) 6. Product Overview The S29GL-P family consists of 1 Gb, 512 Mb, 256 Mb and 128 Mb, 3.0-volt-only, page mode Flash devices optimized for today’s embedded designs that demand a large storage array and rich functionality. These devices are manufactured using 90 nm MirrorBit technology. These products offer uniform 64 Kword (128 Kb) uniform sectors and feature VersatileIO control, allowing control and I/O signals to operate from 1.65 V to VCC. Additional features include: Single word programming or a 32-word buffer for an increased programming speed Program Suspend/Resume and Erase Suspend/Resume Advanced Sector Protection methods for protecting sectors as required 128 words of Secured Silicon area for storing customer and factory secured information. The Secured Silicon Sector is One Time Programmable. 6.1 Memory Map The S29GL-P devices consist of uniform 64 Kword (128 Kb) sectors organized as shown in Table 6.1– Table 6.4. Table 6.1 S29GL01GP Sector & Memory Address Map Uniform Sector Size Sector Count Sector Range SA00 64 Kword/128 Kb 1024 : SA1023 Address Range (16-bit) 0000000h - 000FFFFh : 3FF0000H - 3FFFFFFh Sector Ending Address Notes Sector Starting Address Note This table has been condensed to show sector-related information for an entire device on a single page. Sectors and their address ranges that are not explicitly listed (such as SA001-SA1022) have sector starting and ending addresses that form the same pattern as all other sectors of that size. For example, all 128 Kb sectors have the pattern xxx0000h-xxxFFFFh. Table 6.2 S29GL512P Sector & Memory Address Map Uniform Sector Size Sector Count Sector Range SA00 64 Kword/128 Kb 512 : SA511 Address Range (16-bit) 0000000h - 000FFFFh : 1FF0000H - 1FFFFFFh Sector Ending Address Notes Sector Starting Address Note This table has been condensed to show sector-related information for an entire device on a single page. Sectors and their address ranges that are not explicitly listed (such as SA001-SA510) have sector starting and ending addresses thatthe same pattern as all other sectors of that size. For example, all 128 Kb sectors have the pattern xxx0000h-xxxFFFFh. Table 6.3 S29GL256P Sector & Memory Address Map Uniform Sector Size Sector Count Sector Range SA00 64 Kword/128 Kb 256 : SA255 Address Range (16-bit) 0000000h - 000FFFFh : 0FF0000H - 0FFFFFFh Sector Ending Address Notes Sector Starting Address Note This table has been condensed to show sector-related information for an entire device on a single page. Sectors and their address ranges that are not explicitly listed (such as SA001-SA254) have sector starting and ending addresses that form the same pattern as all other sectors of that size. For example, all 128 Kb sectors have the pattern xxx0000h-xxxFFFFh. November 21, 2006 S29GL-P_00_A3 S29GL-P MirrorBitTM Flash Family 13 Data Sheet (Advance Information) Table 6.4 S29GL128P Sector & Memory Address Map Uniform Sector Size Sector Count Sector Range SA00 64 Kword/128 Kb 128 : SA127 Address Range (16-bit) 0000000h - 000FFFFh : 07F0000 - 7FFFFF Sector Ending Address Notes Sector Starting Address Note This table has been condensed to show sector-related information for an entire device on a single page. Sectors and their address ranges that are not explicitly listed (such as SA001-SA510) have sector starting and ending addresses that form the same pattern as all other sectors of that size. For example, all 128 Kb sectors have the pattern xxx0000h-xxxFFFFh. 7. Device Operations This section describes the read, program, erase, handshaking, and reset features of the Flash devices. Operations are initiated by writing specific commands or a sequence with specific address and data patterns into the command registers (see Table 12.1 through Table 12.4). The command register itself does not occupy any addressable memory location; rather, it is composed of latches that store the commands, along with the address and data information needed to execute the command. The contents of the register serve as input to the internal state machine and the state machine outputs dictate the function of the device. Writing incorrect address and data values or writing them in an improper sequence may place the device in an unknown state, in which case the system must write the reset command to return the device to the reading array data mode. 7.1 Device Operation Table The device must be setup appropriately for each operation. Table 7.1 describes the required state of each control pin for any particular operation. Table 7.1 Device Operations Addresses (Note 1) AIN AIN AIN X X X DQ8–DQ15 DQ0–DQ7 DOUT (Note 3) (Note 3) High-Z High-Z High-Z BYTE#= VIH DOUT (Note 3) (Note 3) High-Z High-Z High-Z BYTE#= VIL DQ8–DQ14 = High-Z, DQ15 = A-1 High-Z High-Z High-Z Operation Read Write (Program/Erase) Accelerated Program Standby Output Disable Reset CE# L L L VCC ± 0.3 V L X OE# L H H X H X WE# H L L X H X RESET# H H H VCC ± 0.3 V H L WP#/ACC X (Note 2) VHH H X X Legend L = Logic Low = VIL, H = Logic High = VIH, VHH = 11.5–12.5V, X = Don’t Care, AIN = Address In, DIN = Data In, DOUT = Data Out Notes 1. Addresses are AMax:A0 in word mode; AMax:A-1 in byte mode. 2. If WP# = VIL, on the outermost sector remains protected. If WP# = VIH, the outermost sector is unprotected. All sectors are unprotected when shipped from the factory (The Secured Silicon Sector can be factory protected depending on version ordered.) 3. DIN or DOUT as required by command sequence, data polling, or sector protect algorithm. 14 S29GL-P MirrorBitTM Flash Family S29GL-P_00_A3 November 21, 2006 Data Sheet (Advance Information) 7.2 Word/Byte Configuration The BYTE# pin controls whether the device data I/O pins operate in the byte or word configuration. If the BYTE# pin is set at logic ‘1’, the device is in word con-figuration, DQ0-DQ15 are active and controlled by CE# and OE#. If the BYTE# pin is set at logic ‘0’, the device is in byte configuration, and only data I/O pins DQ0-DQ7 are active and controlled by CE# and OE#. The data I/O pins DQ8-DQ14 are tri-stated, and the DQ15 pin is used as an input for the LSB (A-1) address function. 7.3 VersatileIOTM (VIO) Control The VersatileIOTM (VIO) control allows the host system to set the voltage levels that the device generates and tolerates on CE# and DQ I/Os to the same voltage level that is asserted on VIO. See Ordering Information for VIO options on this device. For example, a VIO of 1.65-3.6 volts allows for I/O at the 1.8 or 3 volt levels, driving and receiving signals to and from other 1.8 or 3 V devices on the same data bus. 7.4 Read All memories require access time to output array data. In a read operation, data is read from one memory location at a time. Addresses are presented to the device in random order, and the propagation delay through the device causes the data on its outputs to arrive with the address on its inputs. The device defaults to reading array data after device power-up or hardware re-set. To read data from the memory array, the system must first assert a valid address on Amax-A0, while driving OE# and CE# to VIL. WE# must remain at VIH. All addresses are latched on the falling edge of CE#. Data will appear on DQ15DQ0 after ad-dress access time (tACC), which is equal to the delay from stable addresses to valid output data. The OE# signal must be driven to VIL. Data is output on DQ15-DQ0 pins after the access time (tOE) has elapsed from the falling edge of OE#. 7.5 Page Read Mode The device is capable of fast page mode read and is compatible with the page mode Mask ROM read operation. This mode provides faster read access speed for random locations within a page. The page size of the device is 8 words/16 bytes. The appropriate page is selected by the higher address bits A(max)-A3. Address bits A2-A0 in word mode (A2-A-1 in byte mode) determine the specific word within a page. The microprocessor supplies the specific word location. The random or initial page access is equal to tACC or tCE and subsequent page read accesses (as long as the locations specified by the microprocessor falls within that page) is equivalent to tPACC. When CE# is deasserted and reasserted for a subsequent access, the access time is tACC or tCE. Fast page mode accesses are obtained by keeping the “read-page addresses” constant and changing the “intra-read page” addresses. November 21, 2006 S29GL-P_00_A3 S29GL-P MirrorBitTM Flash Family 15 Data Sheet (Advance Information) 7.6 Autoselect The Autoselect mode provides manufacturer and device identification, and sector protection verification, through identifier codes output from the internal register (separate from the memory array) on DQ7-DQ0. This mode is primarily intended for programming equipment to automatically match a device to be programmed with its corresponding programming algorithm (see Table 7.3). The Autoselect codes can also be accessed in-system. When verifying sector protection, the sector address must appear on the appropriate highest order address bits (see Table 7.4 to Table 7.5). The remaining address bits are don't care. When all necessary bits have been set as required, the programming equipment may then read the corresponding identifier code on DQ15DQ0. The Autoselect codes can also be accessed in-system through the command register. There are two methods to access autoselect codes. One uses the autoselect command, the other applies VID on address pin A9. When using programming equipment, the autoselect mode requires VID (11.5 V to 12.5 V) on address pin A9. Address pins must be as shown in Table 7.2. To access the Autoselect codes, the host system must issue the Autoselect command. The Autoselect command sequence may be written to an address within a sector that is either in the read or erase-suspend-read mode. The Autoselect command may not be written while the device is actively programming or erasing. The system must write the reset command to return to the read mode (or erase-suspend-read mode if the sector was previously in Erase Suspend). See Table 12.1 on page 61 for command sequence details. 16 S29GL-P MirrorBitTM Flash Family S29GL-P_00_A3 November 21, 2006 Data Sheet (Advance Information) Table 7.2 Autoselect Codes, (High Voltage Method) Amax A14 to to CE# OE# WE# A16 A10 L L H X X A8 to A7 X A5 to A4 X A3 to A2 L L L L H X X VID X L X H H L L L H X X VID X L X H H L L L H X X VID X L X H H L L L H X X VID X L X H H L L H SA X VID X L X L DQ8 to DQ15 A1 L L H H L H H L H H L H H H A0 L H L H H L H H L H H L H L BYTE# BYTE# = VIL = VIH 00 22 22 22 22 22 22 22 22 22 22 22 22 X X X X X X X X X X X X X X X DQ7 to DQ0 01h 7Eh 28h 01h 7Eh 23h 01h 7Eh 22h 01h 7Eh 21h 01h 01h (protected), 00h (unprotected) 99h (factory locked), 19h (not factory locked) 89h (factory locked), 09h (not factory locked) Description Manufacturer ID: Spansion Product S29GL128P S29GL256P S29GL512P S29GL01GP Device ID Cycle 1 Cycle 2 Cycle 3 Cycle 1 Cycle 2 Cycle 3 Cycle 1 Cycle 2 Cycle 3 Cycle 1 Cycle 2 Cycle 3 A9 VID A6 L Sector Group Protection Verification Secured Silicon Sector Indicator Bit (DQ7), WP# protects highest address sector Secured Silicon Sector Indicator Bit (DQ7), WP# protects lowest address sector Device ID Device ID Device ID L L H X X VID X L X L H H X X L L H X X VID X L X L H H X X Legend L = Logic Low = VIL, H = Logic High = VIH, SA = Sector Address, X = Don’t care. VID = 11.5V to 12.5V Table 7.3 Autoselect Addresses in System Description Manufacturer ID Device ID, Word 1 Address (Base) + 00h (Base) + 01h xx01h/1h 227Eh/7Eh 2228h/28h (GL01GP) 2223h/23h (GL512P) 2222h/22h (GL256P) 2221h/21h (GL128P) 2201h/01h For S29GLxxxPH: XX19h/19h = Not Factory Locked. XX99h/99h = Factory Locked. For S29GLxxxPL: XX09h/09h = Not Factory Locked. XX89h/89h = Factory Locked. xx01h/01h = Locked, xx00h/00h = Unlocked Read Data (word/byte mode) Device ID, Word 2 (Base) + 0Eh Device ID, Word 3 Secure Device Verify Sector Protect Verify (Base) + 0Fh (Base) + 03h (SA) + 02h November 21, 2006 S29GL-P_00_A3 S29GL-P MirrorBitTM Flash Family 17 Data Sheet (Advance Information) Table 7.4 Autoselect Entry in System (LLD Function = lld_AutoselectEntryCmd) Cycle Unlock Cycle 1 Unlock Cycle 2 Autoselect Command Operation Write Write Write Byte Address BasexAAAh Basex555h BasexAAAh Word Address Basex555h Basex2AAh Basex555h Data 0x00AAh 0x0055h 0x0090h Software Functions and Sample Code Table 7.5 Autoselect Exit (LLD Function = lld_AutoselectExitCmd) Cycle Unlock Cycle 1 Note 1. Any offset within the device works. 2. base = base address. Operation Write Byte Address base + XXXh Word Address base + XXXh Data 0x00F0h The following is a C source code example of using the autoselect function to read the manufacturer ID. Refer to the Spansion Low Level Driver User’s Guide (available on www.spansion.com) for general information on Spansion Flash memory software development guidelines. /* Here is an example of Autoselect mode (getting manufacturer ID) */ /* Define UINT16 example: typedef unsigned short UINT16; */ UINT16 manuf_id; /* Auto Select Entry */ *( (UINT16 *)base_addr + 0x555 ) = 0x00AA; /* write unlock cycle 1 */ *( (UINT16 *)base_addr + 0x2AA ) = 0x0055; /* write unlock cycle 2 */ *( (UINT16 *)base_addr + 0x555 ) = 0x0090; /* write autoselect command */ /* multiple reads can be performed after entry */ manuf_id = *( (UINT16 *)base_addr + 0x000 ); /* read manuf. id */ /* Autoselect exit */ *( (UINT16 *)base_addr + 0x000 ) = 0x00F0; /* exit autoselect (write reset command) */ 18 S29GL-P MirrorBitTM Flash Family S29GL-P_00_A3 November 21, 2006 Data Sheet (Advance Information) 7.7 Program/Erase Operations These devices are capable of several modes of programming and or erase operations which are described in detail in the following sections. During a write operation, the system must drive CE# and WE# to VIL and OE# to VIH when providing an address, command, and data. Addresses are latched on the last falling edge of WE# or CE#, while data is latched on the 1st rising edge of WE# or CE#. The Unlock Bypass feature allows the host system to send program commands to the Flash device without first writing unlock cycles within the command sequence. See Section 7.7.8 for details on the Unlock Bypass function. Note the following: When the Embedded Program algorithm is complete, the device returns to the read mode. The system can determine the status of the program operation by using DQ7 or DQ6. Refer to the Write Operation Stat section for information on these status bits. An “0” cannot be programmed back to a “1.” A succeeding read shows that the data is still “0.” Only erase operations can convert a “0” to a “1.” Any commands written to the device during the Embedded Program Algorithm are ignored except the Program Suspend command. Secured Silicon Sector, Autoselect, and CFI functions are unavailable when a program operation is in progress. A hardware reset immediately terminates the program operation and the program command sequence should be reinitiated once the device has returned to the read mode, to ensure data integrity. Programming is allowed in any sequence and across sector boundaries for single word programming operation. Programming to the same word address multiple times without intervening erases is permitted. 7.7.1 Single Word Programming Single word programming mode is one method of programming the Flash. In this mode, four Flash command write cycles are used to program an individual Flash address. The data for this programming operation could be 8 or 16-bits wide. While the single word programming method is supported by all Spansion devices, in general it is not recommended for devices that support Write Buffer Programming. See Table 12.1 on page 61 for the required bus cycles and Figure 7.1 for the flowchart. When the Embedded Program algorithm is complete, the device then returns to the read mode and addresses are no longer latched. The system can determine the status of the program operation by using DQ7 or DQ6. Refer to the Write Operation Status section for information on these status bits. During programming, any command (except the Suspend Program command) is ignored. The Secured Silicon Sector, Autoselect, and CFI functions are unavailable when a program operation is in progress. A hardware reset immediately terminates the program operation. The program command sequence should be reinitiated once the device has returned to the read mode, to ensure data integrity. Programming to the same address multiple times continuously (for example, “walking” a bit within a word) is permitted. November 21, 2006 S29GL-P_00_A3 S29GL-P MirrorBitTM Flash Family 19 Data Sheet (Advance Information) Figure 7.1 Single Word Program Write Unlock Cycles: Address 555h, Data AAh Address 2AAh, Data 55h Unlock Cycle 1 Unlock Cycle 2 Write Program Command: Address 555h, Data A0h Setup Command Program Data to Address: PA, PD Program Address (PA), Program Data (PD) Perform Polling Algorithm (see Write Operation Status flowchart) Polling Status = Busy? No Yes Polling Status = Done? No Yes Error condition (Exceeded Timing Limits) PASS. Device is in read mode. FAIL. Issue reset command to return to read array mode. 20 S29GL-P MirrorBitTM Flash Family S29GL-P_00_A3 November 21, 2006 Data Sheet (Advance Information) Software Functions and Sample Code Table 7.6 Single Word/Byte Program (LLD Function = lld_ProgramCmd) Cycle Unlock Cycle 1 Unlock Cycle 2 Program Setup Program Note Base = Base Address. Operation Write Write Write Write Byte Address Base + AAAh Base + 555h Base + AAAh Byte Address Word Address Base + 555h Base + 2AAh Base + 555h Word Address Data 00AAh 0055h 00A0h Data The following is a C source code example of using the single word program function. Refer to the Spansion Low Level Driver User’s Guide (available on www.spansion.com) for general information on Spansion Flash memory software development guidelines. /* Example: Program Command */ *( (UINT16 *)base_addr + 0x555 ) *( (UINT16 *)base_addr + 0x2AA ) *( (UINT16 *)base_addr + 0x555 ) *( (UINT16 *)pa ) /* Poll for program completion */ = = = = 0x00AA; 0x0055; 0x00A0; data; /* /* /* /* write write write write unlock cycle 1 unlock cycle 2 program setup command data to be programmed */ */ */ */ 7.7.2 Write Buffer Programming Write Buffer Programming allows the system to write a maximum of 32 words in one programming operation. This results in a faster effective word programming time than the standard “word” programming algorithms. The Write Buffer Programming command sequence is initiated by first writing two unlock cycles. This is followed by a third write cycle containing the Write Buffer Load command written at the Sector Address in which programming occurs. At this point, the system writes the number of “word locations minus 1” that are loaded into the page buffer at the Sector Address in which programming occurs. This tells the device how many write buffer addresses are loaded with data and therefore when to expect the “Program Buffer to Flash” confirm command. The number of locations to program cannot exceed the size of the write buffer or the operation aborts. (Number loaded = the number of locations to program minus 1. For example, if the system programs 6 address locations, then 05h should be written to the device.) The system then writes the starting address/data combination. This starting address is the first address/data pair to be programmed, and selects the “write-buffer-page” address. All subsequent address/data pairs must fall within the elected-write-buffer-page. The “write-buffer-page” is selected by using the addresses AMAX–A5. The “write-buffer-page” addresses must be the same for all address/data pairs loaded into the write buffer. (This means Write Buffer Programming cannot be performed across multiple “write-buffer-pages.” This also means that Write Buffer Programming cannot be performed across multiple sectors. If the system attempts to load programming data outside of the selected “write-buffer-page”, the operation ABORTs.) After writing the Starting Address/Data pair, the system then writes the remaining address/data pairs into the write buffer. Note that if a Write Buffer address location is loaded multiple times, the “address/data pair” counter is decremented for every data load operation. Also, the last data loaded at a location before the “Program Buffer to Flash” confirm command is programmed into the device. It is the software's responsibility to comprehend ramifications of loading a write-buffer location more than once. The counter decrements for each data load operation, NOT for each unique write-buffer-address location. Once the specified number of write buffer locations have been loaded, the system must then write the “Program Buffer to Flash” command at the Sector Address. Any other address/data write combinations abort the Write Buffer Programming operation. The device goes “busy.” The Data Bar polling techniques should be used while monitoring the last address location loaded into the write buffer. This eliminates the need to store an address in memory because the system can load the last address location, issue the program confirm command at the last loaded address location, and then data bar poll at that same address. DQ7, DQ6, DQ5, DQ2, and DQ1 should be monitored to determine the device status during Write Buffer Programming. November 21, 2006 S29GL-P_00_A3 S29GL-P MirrorBitTM Flash Family 21 Data Sheet (Advance Information) The write-buffer “embedded” programming operation can be suspended using the standard suspend/resume commands. Upon successful completion of the Write Buffer Programming operation, the device returns to READ mode. The Write Buffer Programming Sequence is ABORTED under any of the following conditions: Load a value that is greater than the page buffer size during the “Number of Locations to Program” step. Write to an address in a sector different than the one specified during the Write-Buffer-Load command. Write an Address/Data pair to a different write-buffer-page than the one selected by the “Starting Address” during the “write buffer data loading” stage of the operation. Write data other than the “Confirm Command” after the specified number of “data load” cycles. The ABORT condition is indicated by DQ1 = 1, DQ7 = DATA# (for the “last address location loaded”), DQ6 = TOGGLE, DQ5 = 0. This indicates that the Write Buffer Programming Operation was ABORTED. A “Write-toBuffer-Abort reset” command sequence is required when using the write buffer Programming features in Unlock Bypass mode. Note that the Secured Silicon sector, autoselect, and CFI functions are unavailable when a program operation is in progress. Write buffer programming is allowed in any sequence of memory (or address) locations. These flash devices are capable of handling multiple write buffer programming operations on the same write buffer address range without intervening erases. Use of the write buffer is strongly recommended for programming when multiple words are to be programmed. 22 S29GL-P MirrorBitTM Flash Family S29GL-P_00_A3 November 21, 2006 Data Sheet (Advance Information) Software Functions and Sample Code Table 7.7 Write Buffer Program (LLD Functions Used = lld_WriteToBufferCmd, lld_ProgramBufferToFlashCmd) Cycle 1 2 3 4 Description Unlock Unlock Write Buffer Load Command Write Word Count Operation Write Write Write Write Byte Address Base + AAAh Base + 555h Word Address Base + 555h Base + 2AAh Data 00AAh 0055h 0025h Word Count (N–1)h Sector Address Sector Address Number of words (N) loaded into the write buffer can be from 1 to 32 words (1 to 64 bytes). 5 to 36 Last Load Buffer Word N Write Buffer to Flash Write Write Program Address, Word N Sector Address Word N 0029h Notes 1. Base = Base Address. 2. Last = Last cycle of write buffer program operation; depending on number of words written, the total number of cycles may be from 6 to 37. 3. For maximum efficiency, it is recommended that the write buffer be loaded with the highest number of words (N words) possible. The following is a C source code example of using the write buffer program function. Refer to the Spansion Low Level Driver User’s Guide (available on www.spansion.com) for general information on Spansion Flash memory software development guidelines. /* Example: Write Buffer Programming Command */ /* NOTES: Write buffer programming limited to 16 words. */ /* All addresses to be written to the flash in */ /* one operation must be within the same flash */ /* page. A flash page begins at addresses */ /* evenly divisible by 0x20. */ UINT16 *src = source_of_data; /* address of source data */ UINT16 *dst = destination_of_data; /* flash destination address */ UINT16 wc = words_to_program -1; /* word count (minus 1) */ *( (UINT16 *)base_addr + 0x555 ) = 0x00AA; /* write unlock cycle 1 */ *( (UINT16 *)base_addr + 0x2AA ) = 0x0055; /* write unlock cycle 2 */ *( (UINT16 *)sector_address ) = 0x0025; /* write write buffer load command */ *( (UINT16 *)sector_address ) = wc; /* write word count (minus 1) */ loop: *dst = *src; /* ALL dst MUST BE SAME PAGE */ /* write source data to destination */ dst++; /* increment destination pointer */ src++; /* increment source pointer */ if (wc == 0) goto confirm /* done when word count equals zero */ wc--; /* decrement word count */ goto loop; /* do it again */ confirm: *( (UINT16 *)sector_address ) = 0x0029; /* write confirm command */ /* poll for completion */ /* Example: Write Buffer Abort Reset */ *( (UINT16 *)addr + 0x555 ) = 0x00AA; *( (UINT16 *)addr + 0x2AA ) = 0x0055; *( (UINT16 *)addr + 0x555 ) = 0x00F0; /* write unlock cycle 1 /* write unlock cycle 2 /* write buffer abort reset */ */ */ November 21, 2006 S29GL-P_00_A3 S29GL-P MirrorBitTM Flash Family 23 Data Sheet (Advance Information) Figure 7.2 Write Buffer Programming Operation Write Unlock Cycles: Address 555h, Data AAh Address 2AAh, Data 55h Unlock Cycle 1 Unlock Cycle 2 Issue Write Buffer Load Command: Address SA, Data 25h Load Word Count to Program Program Data to Address: SA, wc wc = number of words – 1 Yes wc = 0? Confirm command: SA = 0x29h No Wait 4 ms (Recommended) No Write Buffer Abort Desired? Perform Polling Algorithm Yes Write to a Different Sector Address to Cause Write Buffer Abort (see Write Operation Status flowchart) Write Next Word, Decrement wc: wc = wc – 1 Polling Status = Done? No No Yes Error? Yes Yes Write Buffer Abort? No RESET. Issue Write Buffer Abort Reset Command FAIL. Issue reset command to return to read array mode. PASS. Device is in read mode. 24 S29GL-P MirrorBitTM Flash Family S29GL-P_00_A3 November 21, 2006 Data Sheet (Advance Information) 7.7.3 Sector Erase The sector erase function erases one or more sectors in the memory array. (See Table 12.1 on page 61 and Figure 7.3.) The device does not require the system to preprogram prior to erase. The Embedded Erase algorithm automatically programs and verifies the entire memory for an all zero data pattern prior to electrical erase. After a successful sector erase, all locations within the erased sector contain FFFFh. The system is not required to provide any controls or timings during these operations. After the command sequence is written, a sector erase time-out of no less than 50 µs occurs. During the timeout period, additional sector addresses and sector erase commands may be written. Loading the sector erase buffer may be done in any sequence, and the number of sectors may be from one sector to all sectors. The time between these additional cycles must be less than 50 µs. Any sector erase address and command following the exceeded time-out (50µs) may or may not be accepted. Any command other than Sector Erase or Erase Suspend during the time-out period resets that sector to the read mode. The system can monitor DQ3 to determine if the sector erase timer has timed out (See Section 7.8.6.) The time-out begins from the rising edge of the final WE# pulse in the command sequence. When the Embedded Erase algorithm is complete, the sector returns to reading array data and addresses are no longer latched. The system can determine the status of the erase operation by reading DQ7 or DQ6/DQ2 in the erasing sector. Refer to Section 7.8 for information on these status bits. Once the sector erase operation has begun, only the Erase Suspend command is valid. All other commands are ignored. However, note that a hardware reset immediately terminates the erase operation. If that occurs, the sector erase command sequence should be reinitiated once that sector has returned to reading array data, to ensure the sector is properly erased. The Unlock Bypass feature allows the host system to send program commands to the Flash device without first writing unlock cycles within the command sequence. See Section 7.7.8 for details on the Unlock Bypass function. Figure 7.3 illustrates the algorithm for the erase operation. Refer to Section 11.7.5 for parameters and timing diagrams. Software Functions and Sample Code Table 7.8 Sector Erase (LLD Function = lld_SectorEraseCmd) Cycle 1 2 3 4 5 6 Description Unlock Unlock Setup Command Unlock Unlock Sector Erase Command Operation Write Write Write Write Write Write Byte Address Base + AAAh Base + 555h Base + AAAh Base + AAAh Base + 555h Sector Address Word Address Base + 555h Base + 2AAh Base + 555h Base + 555h Base + 2AAh Sector Address Data 00AAh 0055h 0080h 00AAh 0055h 0030h Unlimited additional sectors may be selected for erase; command(s) must be written within 50 µs. The following is a C source code example of using the sector erase function. Refer to the Spansion Low Level Driver User’s Guide (available on www.spansion.com) for general information on Spansion Flash memory software development guidelines. /* Example: Sector Erase Command */ *( *( *( *( *( *( (UINT16 (UINT16 (UINT16 (UINT16 (UINT16 (UINT16 *)base_addr + 0x555 *)base_addr + 0x2AA *)base_addr + 0x555 *)base_addr + 0x555 *)base_addr + 0x2AA *)sector_address ) ) ) ) ) ) = = = = = = 0x00AA; 0x0055; 0x0080; 0x00AA; 0x0055; 0x0030; /* /* /* /* /* /* write write write write write write unlock cycle 1 */ unlock cycle 2 */ setup command */ additional unlock cycle 1 */ additional unlock cycle 2 */ sector erase command */ November 21, 2006 S29GL-P_00_A3 S29GL-P MirrorBitTM Flash Family 25 Data Sheet (Advance Information) Figure 7.3 Sector Erase Operation Write Unlock Cycles: Address 555h, Data AAh Address 2AAh, Data 55h Unlock Cycle 1 Unlock Cycle 2 Write Sector Erase Cycles: Address 555h, Data 80h Address 555h, Data AAh Address 2AAh, Data 55h Sector Address, Data 30h Command Cycle 1 Command Cycle 2 Command Cycle 3 Specify first sector for erasure No Select Additional Sectors? Yes Write Additional Sector Addresses • Each additional cycle must be written within tSEA timeout • The host system may monitor DQ3 or wait tSEA to ensure acceptance of erase commands • No limit on number of sectors No Poll DQ3. DQ3 = 1? Yes Yes Last Sector Selected? No • Commands other than Erase Suspend or selecting additional sectors for erasure during timeout reset device to reading array data Wait 4 ms (Recommended) Perform Write Operation Status Algorithm (see Figure 7.4) Status may be obtained by reading DQ7, DQ6 and/or DQ2. Yes Done? No DQ5 = 1? Yes No Error condition (Exceeded Timing Limits) PASS. Device returns to reading array. FAIL. Write reset command to return to reading array. Notes 1. See Table 12.1 on page 61 for erase command sequence. 2. See the section on DQ3 for information on the sector erase timeout. 26 S29GL-P MirrorBitTM Flash Family S29GL-P_00_A3 November 21, 2006 Data Sheet (Advance Information) 7.7.4 Chip Erase Command Sequence Chip erase is a six-bus cycle operation as indicated by Table 12.1 on page 61. These commands invoke the Embedded Erase algorithm, which does not require the system to preprogram prior to erase. The Embedded Erase algorithm automatically preprograms and verifies the entire memory for an all zero data pattern prior to electrical erase. After a successful chip erase, all locations of the chip contain FFFFh. The system is not required to provide any controls or timings during these operations. The “Command Definition” section in the appendix shows the address and data requirements for the chip erase command sequence. When the Embedded Erase algorithm is complete, that sector returns to the read mode and addresses are no longer latched. The system can determine the status of the erase operation by using DQ7 or DQ6/DQ2. Refer to “Write Operation Status” for information on these status bits. The Unlock Bypass feature allows the host system to send program commands to the Flash device without first writing unlock cycles within the command sequence. See Section 7.7.8 for details on the Unlock Bypass function. Any commands written during the chip erase operation are ignored. However, note that a hardware reset immediately terminates the erase operation. If that occurs, the chip erase command sequence should be reinitiated once that sector has returned to reading array data, to ensure the entire array is properly erased. Software Functions and Sample Code Table 7.9 Chip Erase (LLD Function = lld_ChipEraseCmd) Cycle 1 2 3 4 5 6 Description Unlock Unlock Setup Command Unlock Unlock Chip Erase Command Operation Write Write Write Write Write Write Byte Address Base + AAAh Base + 555h Base + AAAh Base + AAAh Base + 555h Base + AAAh Word Address Base + 555h Base + 2AAh Base + 555h Base + 555h Base + 2AAh Base + 555h Data 00AAh 0055h 0080h 00AAh 0055h 0010h The following is a C source code example of using the chip erase function. Refer to the Spansion Low Level Driver User’s Guide (available on www.spansion.com) for general information on Spansion Flash memory software development guidelines. /* Example: Chip Erase Command */ /* Note: Cannot be suspended */ *( (UINT16 *)base_addr + 0x555 ) *( (UINT16 *)base_addr + 0x2AA ) *( (UINT16 *)base_addr + 0x555 ) *( (UINT16 *)base_addr + 0x555 ) *( (UINT16 *)base_addr + 0x2AA ) *( (UINT16 *)base_addr + 0x000 ) = = = = = = 0x00AA; 0x0055; 0x0080; 0x00AA; 0x0055; 0x0010; /* /* /* /* /* /* write write write write write write unlock cycle 1 */ unlock cycle 2 */ setup command */ additional unlock cycle 1 */ additional unlock cycle 2 */ chip erase command */ November 21, 2006 S29GL-P_00_A3 S29GL-P MirrorBitTM Flash Family 27 Data Sheet (Advance Information) 7.7.5 Erase Suspend/Erase Resume Commands The Erase Suspend command allows the system to interrupt a sector erase operation and then read data from, or program data to, any sector not selected for erasure. The sector address is required when writing this command. This command is valid only during the sector erase operation, including the minimum 50 µs timeout period during the sector erase command sequence. The Erase Suspend command is ignored if written during the chip erase operation. When the Erase Suspend command is written during the sector erase operation, the device requires a maximum of 20 µs (5 µs typical) to suspend the erase operation. However, when the Erase Suspend command is written during the sector erase time-out, the device immediately terminates the time-out period and suspends the erase operation. After the erase operation has been suspended, the device enters the erase-suspend-read mode. The system can read data from or program data to any sector not selected for erasure. (The device “erase suspends” all sectors selected for erasure.) Reading at any address within erase-suspended sectors produces status information on DQ7-DQ0. The system can use DQ7, or DQ6, and DQ2 together, to determine if a sector is actively erasing or is erase-suspended. Refer to Table 7.35 for information on these status bits. After an erase-suspended program operation is complete, the device returns to the erase-suspend-read mode. The system can determine the status of the program operation using the DQ7 or DQ6 status bits, just as in the standard program operation. In the erase-suspend-read mode, the system can also issue the Autoselect command sequence. Refer to the “Write Buffer Programming Operation” section and the “Autoselect Command Sequence” section for details. To resume the sector erase operation, the system must write the Erase Resume command. The address of the erase-suspended sector is required when writing this command. Further writes of the Resume command are ignored. Another Erase Suspend command can be written after the chip has resumed erasing. Software Functions and Sample Code Table 7.10 Erase Suspend (LLD Function = lld_EraseSuspendCmd) Cycle 1 Operation Write Byte Address Base + XXXh Word Address Base + XXXh Data 00B0h The following is a C source code example of using the erase suspend function. Refer to the Spansion Low Level Driver User’s Guide (available on www.spansion.com) for general information on Spansion Flash memory software development guidelines. /* Example: Erase suspend command */ *( (UINT16 *)base_addr + 0x000 ) = 0x00B0; /* write suspend command */ Table 7.11 Erase Resume (LLD Function = lld_EraseResumeCmd) Cycle 1 Operation Write Byte Address Sector Address Word Address Sector Address Data 0030h The following is a C source code example of using the erase resume function. Refer to the Spansion Low Level Driver User’s Guide (available on www.spansion.com) for general information on Spansion Flash memory software development guidelines. /* Example: Erase resume command */ *( (UINT16 *)sector_addr + 0x000 ) = 0x0030; /* write resume command /* The flash needs adequate time in the resume state */ */ 28 S29GL-P MirrorBitTM Flash Family S29GL-P_00_A3 November 21, 2006 Data Sheet (Advance Information) 7.7.6 Program Suspend/Program Resume Commands The Program Suspend command allows the system to interrupt an embedded programming operation or a “Write to Buffer” programming operation so that data can read from any non-suspended sector. When the Program Suspend command is written during a programming process, the device halts the programming operation within 15 µs maximum (5 µs typical) and updates the status bits. Addresses are “don't-cares” when writing the Program Suspend command. After the programming operation has been suspended, the system can read array data from any nonsuspended sector. The Program Suspend command may also be issued during a programming operation while an erase is suspended. In this case, data may be read from any addresses not in Erase Suspend or Program Suspend. If a read is needed from the Secured Silicon Sector area, then user must use the proper command sequences to enter and exit this region. The system may also write the Autoselect command sequence when the device is in Program Suspend mode. The device allows reading Autoselect codes in the suspended sectors, since the codes are not stored in the memory array. When the device exits the Autoselect mode, the device reverts to Program Suspend mode, and is ready for another valid operation. See “Autoselect Command Sequence” for more information. After the Program Resume command is written, the device reverts to programming. The system can determine the status of the program operation using the DQ7 or DQ6 status bits, just as in the standard program operation. See “Write Operation Status” for more information. The system must write the Program Resume command (address bits are “don't care”) to exit the Program Suspend mode and continue the programming operation. Further writes of the Program Resume command are ignored. Another Program Suspend command can be written after the device has resumed programming. Software Functions and Sample Code Table 7.12 Program Suspend (LLD Function = lld_ProgramSuspendCmd) Cycle 1 Operation Write Word Address Base + XXXh Data 00B0h The following is a C source code example of using the program suspend function. Refer to the Spansion Low Level Driver User’s Guide (available on www.spansion.com) for general information on Spansion Flash memory software development guidelines. /* Example: Program suspend command */ *( (UINT16 *)base_addr + 0x000 ) = 0x00B0; /* write suspend command */ Table 7.13 Program Resume (LLD Function = lld_ProgramResumeCmd) Cycle 1 Operation Write Word Address Base + XXXh Data 0030h The following is a C source code example of using the program resume function. Refer to the Spansion Low Level Driver User’s Guide (available on www.spansion.com) for general information on Spansion Flash memory software development guidelines. /* Example: Program resume command */ *( (UINT16 *)base_addr + 0x000 ) = 0x0030; /* write resume command */ November 21, 2006 S29GL-P_00_A3 S29GL-P MirrorBitTM Flash Family 29 Data Sheet (Advance Information) 7.7.7 Accelerated Program Accelerated single word programming and write buffer programming operations are enabled through the WP#/ACC pin. This method is faster than the standard program command sequences. Note The accelerated program functions must not be used more than 10 times per sector. If the system asserts VHH on this input, the device automatically enters the aforementioned Unlock Bypass mode and uses the higher voltage on the input to reduce the time required for program operations. The system can then use the Write Buffer Load command sequence provided by the Unlock Bypass mode. Note that if a “Write-to-Buffer-Abort Reset” is required while in Unlock Bypass mode, the full 3-cycle RESET command sequence must be used to reset the device. Removing VHH from the ACC input, upon completion of the embedded program operation, returns the device to normal operation. Sectors must be unlocked prior to raising WP#/ACC to VHH. The WP#/ACC pin must not be at VHH for operations other than accelerated programming, or device damage may result. The WP#/ACC pin must not be left floating or unconnected; inconsistent behavior of the device may result. 7.7.8 Unlock Bypass The device features an Unlock Bypass mode to facilitate faster word programming. Once the device enters the Unlock Bypass mode, only two write cycles are required to program data, instead of the normal four cycles. This mode dispenses with the initial two unlock cycles required in the standard program command sequence, resulting in faster total programming time. The “Command Definition Summary” section shows the requirements for the unlock bypass command sequences. During the unlock bypass mode, only the Read, Unlock Bypass Program and Unlock Bypass Reset commands are valid. To exit the unlock bypass mode, the system must issue the two-cycle unlock bypass reset command sequence. The first cycle must contain the sector address and the data 90h. The second cycle need only contain the data 00h. The sector then returns to the read mode. Software Functions and Sample Code The following are C source code examples of using the unlock bypass entry, program, and exit functions. Refer to the Spansion Low Level Driver User’s Guide (available soon on www.spansion.com) for general information on Spansion Flash memory software development guidelines. Table 7.14 Unlock Bypass Entry (LLD Function = lld_UnlockBypassEntryCmd) Cycle 1 2 3 Description Unlock Unlock Entry Command Operation Write Write Write Word Address Base + 555h Base + 2AAh Base + 555h Data 00AAh 0055h 0020h /* Example: Unlock Bypass Entry Command */ *( (UINT16 *)base_addr + 0x555 ) = 0x00AA; /* write unlock *( (UINT16 *)base_addr + 0x2AA ) = 0x0055; /* write unlock *( (UINT16 *)base_addr + 0x555 ) = 0x0020; /* write unlock /* At this point, programming only takes two write cycles. /* Once you enter Unlock Bypass Mode, do a series of like /* operations (programming or sector erase) and then exit /* Unlock Bypass Mode before beginning a different type of /* operations. cycle 1 cycle 2 bypass command */ */ */ */ */ */ */ */ 30 S29GL-P MirrorBitTM Flash Family S29GL-P_00_A3 November 21, 2006 Data Sheet (Advance Information) Table 7.15 Unlock Bypass Program (LLD Function = lld_UnlockBypassProgramCmd) Cycle 1 2 Description Program Setup Command Program Command Operation Write Write Word Address Base +xxxh Program Address Data 00A0h Program Data /* Example: Unlock Bypass Program Command */ /* Do while in Unlock Bypass Entry Mode! */ *( (UINT16 *)base_addr + 0x555 ) = 0x00A0; *( (UINT16 *)pa ) = data; /* Poll until done or error. */ /* If done and more to program, */ /* do above two cycles again. */ /* write program setup command /* write data to be programmed */ */ Table 7.16 Unlock Bypass Reset (LLD Function = lld_UnlockBypassResetCmd) Cycle 1 2 Description Reset Cycle 1 Reset Cycle 2 Operation Write Write Word Address Base +xxxh Base +xxxh Data 0090h 0000h /* Example: Unlock Bypass Exit Command */ *( (UINT16 *)base_addr + 0x000 ) = 0x0090; *( (UINT16 *)base_addr + 0x000 ) = 0x0000; 7.8 Write Operation Status The device provides several bits to determine the status of a program or erase operation. The following subsections describe the function of DQ1, DQ2, DQ3, DQ5, DQ6, and DQ7. 7.8.1 DQ7: Data# Polling The Data# Polling bit, DQ7, indicates to the host system whether an Embedded Program or Erase algorithm is in progress or completed, or whether the device is in Erase Suspend. Data# Polling is valid after the rising edge of the final WE# pulse in the command sequence. Note that the Data# Polling is valid only for the last word being programmed in the write-buffer-page during Write Buffer Programming. Reading Data# Polling status on any word other than the last word to be programmed in the write-buffer-page returns false status information. During the Embedded Program algorithm, the device outputs on DQ7 the complement of the datum programmed to DQ7. This DQ7 status also applies to programming during Erase Suspend. When the Embedded Program algorithm is complete, the device outputs the datum programmed to DQ7. The system must provide the program address to read valid status information on DQ7. If a program address falls within a protected sector, Data# polling on DQ7 is active for approximately 1 µs, then that sector returns to the read mode. During the Embedded Erase Algorithm, Data# polling produces a “0” on DQ7. When the Embedded Erase algorithm is complete, or if the device enters the Erase Suspend mode, Data# Polling produces a “1” on DQ7. The system must provide an address within any of the sectors selected for erasure to read valid status information on DQ7. After an erase command sequence is written, if all sectors selected for erasing are protected, Data# Polling on DQ7 is active for approximately 100 µs, then the device returns to the read mode. If not all selected sectors are protected, the Embedded Erase algorithm erases the unprotected sectors, and ignores the selected sectors that are protected. However, if the system reads DQ7 at an address within a protected sector, the status may not be valid. Just prior to the completion of an Embedded Program or Erase operation, DQ7 may change with DQ6-DQ0 while Output Enable (OE#) is asserted low. That is, the device may change from providing status information November 21, 2006 S29GL-P_00_A3 S29GL-P MirrorBitTM Flash Family 31 Data Sheet (Advance Information) to valid data on DQ7. Depending on when the system samples the DQ7 output, it may read the status or valid data. Even if the device has completed the program or erase operation and DQ7 has valid data, the data outputs on DQ6-DQ0 may be still invalid. Valid data on DQ7-D00 appears on successive read cycles. See the following for more information: Table 7.17, shows the outputs for Data# Polling on DQ7. Figure 7.4, shows the Data# Polling algorithm; and Figure 11.7, shows the Data# Polling timing diagram. Figure 7.4 Write Operation Status Flowchart START Read 1 (Note 6) DQ7=valid data? NO YES Program Operation Complete YES Read 1 DQ5=1? NO Read 2 Read3= valid data? YES NO Read 3 Read 2 YES Write Buffer Programming? Program Operation Failed YES NO Read 3 Device BUSY, Re-Poll Programming Operation? NO (Note 3) (Note 1) DQ6 toggling? YES TIMEOUT (Note 1) DQ6 toggling? NO (Note 2) (Note 5) YES DEVICE ERROR (Note 4) Read1 DQ1=1? YES NO YES DQ2 toggling? NO NO Device BUSY, Re-Poll Read 2 Device BUSY, Re-Poll Erase Operation Complete Read 3 Device in Erase/Suspend Mode YES Read3 DQ1=1 AND DQ7 ? Valid Data? Write Buffer Operation Failed NO Device BUSY, Re-Poll Notes: 1) DQ6 is toggling if Read2 DQ6 does not equal Read3 DQ6. 2) DQ2 is toggling if Read2 DQ2 does not equal Read3 DQ2. 3) May be due to an attempt to program a 0 to 1. Use the RESET command to exit operation. 4) Write buffer error if DQ1 of last read =1. 5) Invalid state, use RESET command to exit operation. 6) Valid data is the data that is intended to be programmed or all 1's for an erase operation. 7) Data polling algorithm valid for all operations except advanced sector protection. 32 S29GL-P MirrorBitTM Flash Family S29GL-P_00_A3 November 21, 2006 Data Sheet (Advance Information) 7.8.2 DQ6: Toggle Bit I Toggle Bit I on DQ6 indicates whether an Embedded Program or Erase algorithm is in progress or complete, or whether the device has entered the Erase Suspend mode. Toggle Bit I may be read at any address, and is valid after the rising edge of the final WE# pulse in the command sequence (prior to the program or erase operation), and during the sector erase time-out. During an Embedded Program or Erase algorithm operation, successive read cycles to any address cause DQ6 to toggle. When the operation is complete, DQ6 stops toggling. After an erase command sequence is written, if all sectors selected for erasing are protected, DQ6 toggles for approximately 100μs, then returns to reading array data. If not all selected sectors are protected, the Embedded Erase algorithm erases the unprotected sectors, and ignores the selected sectors that are protected. The system can use DQ6 and DQ2 together to determine whether a sector is actively erasing or is erasesuspended. When the device is actively erasing (that is, the Embedded Erase algorithm is in progress), DQ6 toggles. When the device enters the Erase Suspend mode, DQ6 stops toggling. However, the system must also use DQ2 to determine which sectors are erasing or erase-suspended. Alternatively, the system can use DQ7 (see the subsection on DQ7: Data# Polling). If a program address falls within a protected sector, DQ6 toggles for approximately 1μs after the program command sequence is written, then returns to reading array data. DQ6 also toggles during the erase-suspend-program mode, and stops toggling once the Embedded Program Algorithm is complete. See the following for additional information: Figure 7.4, Figure 11.13 on page 57, and Table 7.17. Toggle Bit I on DQ6 requires either OE# or CE# to be de-asserted and reasserted to show the change in state. 7.8.3 DQ2: Toggle Bit II The “Toggle Bit II” on DQ2, when used with DQ6, indicates whether a particular sector is actively erasing (that is, the Embedded Erase algorithm is in progress), or whether that sector is erase-suspended. Toggle Bit II is valid after the rising edge of the final WE# pulse in the command sequence. DQ2 toggles when the system reads at addresses within those sectors that have been selected for erasure. But DQ2 cannot distinguish whether the sector is actively erasing or is erase-suspended. DQ6, by comparison, indicates whether the device is actively erasing, or is in Erase Suspend, but cannot distinguish which sectors are selected for erasure. Thus, both status bits are required for sector and mode information. Refer to Table 7.17 to compare outputs for DQ2 and DQ6. See Figure 11.14 on page 57 for additional information. 7.8.4 Reading Toggle Bits DQ6/DQ2 Whenever the system initially begins reading toggle bit status, it must read DQ7–DQ0 at least twice in a row to determine whether a toggle bit is toggling. Typically, the system would note and store the value of the toggle bit after the first read. After the second read, the system would compare the new value of the toggle bit with the first. If the toggle bit is not toggling, the device has completed the program or erases operation. The system can read array data on DQ7–DQ0 on the following read cycle. However, if after the initial two read cycles, the system determines that the toggle bit is still toggling, the system also should note whether the value of DQ5 is high (see the section on DQ5). If it is, the system should then determine again whether the toggle bit is toggling, since the toggle bit may have stopped toggling just as DQ5 went high. If the toggle bit is no longer toggling, the device has successfully completed the program or erases operation. If it is still toggling, the device did not complete the operation successfully, and the system must write the reset command to return to reading array data. The remaining scenario is that the system initially determines that the toggle bit is toggling and DQ5 has not gone high. The system may continue to monitor the toggle bit and DQ5 through successive read cycles, determining the status as described in the previous paragraph. Alternatively, it may choose to perform other system tasks. In this case, the system must start at the beginning of the algorithm when it returns to determine the status of the operation. Refer to Figure 7.4 for more details. Note When verifying the status of a write operation (embedded program/erase) of a memory sector, DQ6 and DQ2 toggle between high and low states in a series of consecutive and con-tiguous status read cycles. In order for November 21, 2006 S29GL-P_00_A3 S29GL-P MirrorBitTM Flash Family 33 Data Sheet (Advance Information) this toggling behavior to be properly observed, the consecutive status bit reads must not be interleaved with read accesses to other memory sectors. If it is not possible to temporarily prevent reads to other memory sectors, then it is recommended to use the DQ7 status bit as the alternative method of determining the active or inactive status of the write operation. 7.8.5 DQ5: Exceeded Timing Limits DQ5 indicates whether the program or erase time has exceeded a specified internal pulse count limit. Under these conditions DQ5 produces a “1,” indicating that the program or erase cycle was not successfully completed. The system must write the reset command to return to the read mode (or to the erase-suspendread mode if a sector was previously in the erase-suspend-program mode). 7.8.6 DQ3: Sector Erase Timeout State Indicator After writing a sector erase command sequence, the system may read DQ3 to determine whether or not erasure has begun. (The sector erase timer does not apply to the chip erase command.) If additional sectors are selected for erasure, the entire time-out also applies after each additional sector erase command. When the time-out period is complete, DQ3 switches from a “0” to a “1.” If the time between additional sector erase commands from the system can be assumed to be less than 50 µs, then the system need not monitor DQ3. See Sector Erase Command Sequence for more details. After the sector erase command is written, the system should read the status of DQ7 (Data# Polling) or DQ6 (Toggle Bit I) to ensure that the device has accepted the command sequence, and then read DQ3. If DQ3 is “1,” the Embedded Erase algorithm has begun; all further commands (except Erase Suspend) are ignored until the erase operation is complete. If DQ3 is “0,” the device accepts additional sector erase commands. To ensure the command has been accepted, the system software should check the status of DQ3 prior to and following each sub-sequent sector erase command. If DQ3 is high on the second status check, the last command might not have been accepted. Table 7.17 shows the status of DQ3 relative to the other status bits. 7.8.7 DQ1: Write to Buffer Abort DQ1 indicates whether a Write to Buffer operation was aborted. Under these conditions DQ1 produces a “1”. The system must issue the Write to Buffer Abort Reset command sequence to return the device to reading array data. See Write Buffer Programming Operation for more details. 34 S29GL-P MirrorBitTM Flash Family S29GL-P_00_A3 November 21, 2006 Data Sheet (Advance Information) Table 7.17 Write Operation Status Status Standard Mode Program Suspend Mode Embedded Program Algorithm Embedded Erase Algorithm ProgramSuspend Read Program-Suspended Sector Non-Program Suspended Sector Erase-Suspended Sector Non-Erase Suspended Sector DQ7# DQ7# DQ7# Toggle Toggle Toggle 0 0 0 1 No toggle 0 Data N/A N/A N/A N/A N/A N/A N/A 0 1 DQ7 (Note 2) DQ7# 0 DQ6 Toggle Toggle DQ5 (Note 1) 0 0 DQ3 N/A 1 DQ2 (Note 2) No toggle Toggle DQ1 0 N/A RY/ BY# 0 0 1 1 N/A Toggle N/A 1 1 0 0 0 Invalid (not allowed) Data Erase Suspend Mode EraseSuspend Read Erase-Suspend-Program (Embedded Program) Write-toBuffer Busy (Note 3) Abort (Note 4) Notes 1. DQ5 switches to 1 when an Embedded Program, Embedded Erase, or Write-to-Buffer operation has exceeded the maximum timing limits. Refer to the section on DQ5 for more information. 2. DQ7 and DQ2 require a valid address when reading status information. Refer to the appropriate subsection for further details. 3. The Data# Polling algorithm should be used to monitor the last loaded write-buffer address location. 4. DQ1 switches to 1 when the device has aborted the write-to-buffer operation 7.9 Writing Commands/Command Sequences During a write operation, the system must drive CE# and WE# to VIL and OE# to VIH when providing an address, command, and data. Addresses are latched on the last falling edge of WE# or CE#, while data is latched on the 1st rising edge of WE# or CE#. An erase operation can erase one sector, multiple sectors, or the entire device. Table 6.2–Table 6.3 indicate the address space that each sector occupies. The device address space is divided into uniform 64KW/128KB sectors. A sector address is the set of address bits required to uniquely select a sector. ICC2 in “DC Characteristics” represents the active current specification for the write mode. “AC Characteristics” contains timing specification tables and timing diagrams for write operations. 7.9.1 RY/BY# This feature allows the host system to detect when data is ready to be read by simply monitoring the RY/BY# pin, which is a dedicated output and controlled by CE#. The device address space is divided into uniform 64KW/128KB sectors. A sector address is the set of address bits required to uniquely select a sector. 7.9.2 Hardware Reset The RESET# input provides a hardware method of resetting the device to reading array data. When RESET# is driven low for at least a period of tRP, the device immediately terminates any operation in progress, tristates all outputs, resets the configuration register, and ignores all read/write commands for the duration of the RESET# pulse. The device also resets the internal state machine to reading array data. To ensure data integrity the operation that was interrupted should be reinitiated once the device is ready to accept another command sequence. When RESET# is held at VSS, the device draws VCC reset current (ICC5). If RESET# is held at VIL, but not at VSS, the standby current is greater. RESET# may be tied to the system reset circuitry which enables the system to read the boot-up firmware from the Flash memory upon a system reset. See Figure 11.7 on page 53 and Figure 11.8 on page 54 for timing diagrams. November 21, 2006 S29GL-P_00_A3 S29GL-P MirrorBitTM Flash Family 35 Data Sheet (Advance Information) Note Hardware reset operation during embedded erase is not recommended; permanent device damage may result. 7.9.3 Software Reset Software reset is part of the command set (see Table 12.1 on page 61) that also returns the device to array read mode and must be used for the following conditions: 1. to exit Autoselect mode 2. when DQ5 goes high during write status operation that indicates program or erase cycle was not successfully completed 3. exit sector lock/unlock operation. 4. to return to erase-suspend-read mode if the device was previously in Erase Suspend mode. 5. after any aborted operations Software Functions and Sample Code Table 7.18 Reset (LLD Function = lld_ResetCmd) Cycle Reset Command Note Base = Base Address. Operation Write Byte Address Base + xxxh Word Address Base + xxxh Data 00F0h The following is a C source code example of using the reset function. Refer to the Spansion Low Level Driver User’s Guide (available on www.spansion.com) for general information on Spansion Flash memory software development guidelines. /* Example: Reset (software reset of Flash state machine) */ *( (UINT16 *)base_addr + 0x000 ) = 0x00F0; The following are additional points to consider when using the reset command: This command resets the sectors to the read and address bits are ignored. Reset commands are ignored once erasure has begun until the operation is complete. Once programming begins, the device ignores reset commands until the operation is complete The reset command may be written between the cycles in a program command sequence before programming begins (prior to the third cycle). This resets the sector to which the system was writing to the read mode. If the program command sequence is written to a sector that is in the Erase Suspend mode, writing the reset command returns that sector to the erase-suspend-read mode. The reset command may be also written during an Autoselect command sequence. If a sector has entered the Autoselect mode while in the Erase Suspend mode, writing the reset command returns that sector to the erase-suspend-read mode. If DQ1 goes high during a Write Buffer Programming operation, the system must write the "Write to Buffer Abort Reset" command sequence to RESET the device to reading array data. The standard RESET command does not work during this condition. To exit the unlock bypass mode, the system must issue a two-cycle unlock bypass reset command sequence [see command table for details]. 36 S29GL-P MirrorBitTM Flash Family S29GL-P_00_A3 November 21, 2006 Data Sheet (Advance Information) 8. Advanced Sector Protection/Unprotection The Advanced Sector Protection/Unprotection feature disables or enables programming or erase operations in any or all sectors and can be implemented through software and/or hardware methods, which are independent of each other. This section describes the various methods of protecting data stored in the memory array. An overview of these methods in shown in Figure 8.1. Figure 8.1 Advanced Sector Protection/Unprotection Hardware Methods Software Methods Lock Register WP#/ACC = VIL (Highest or Lowest Sector Locked) (One Time Programmable) Password Method (DQ2) Persistent Method (DQ1) 64-bit Password (One Time Protect) PPB Lock Bit1,2,3 0 = PPBs Locked 1 = PPBs Unlocked 1. Bit is volatile, and defaults to “1” on reset. 2. Programming to “0” locks all PPBs to their current state. 3. Once programmed to “0”, requires hardware reset to unlock. Memory Array Sector 0 Sector 1 Sector 2 Persistent Protection Bit (PPB)4,5 PPB 0 PPB 1 PPB 2 Dynamic Protection Bit (DYB)6,7,8 DYB 0 DYB 1 DYB 2 Sector N-2 Sector N-1 Sector N 3 PPB N-2 PPB N-1 PPB N 4. 0 = Sector Protected, 1 = Sector Unprotected. 5. PPBs programmed individually, but cleared collectively DYB N-2 DYB N-1 DYB N 6. 0 = Sector Protected, 1 = Sector Unprotected. 7. Protect effective only if PPB Lock Bit is unlocked and corresponding PPB is “1” (unprotected). 8. Volatile Bits: defaults to user choice upon power-up (see ordering options). 3. N = Highest Address Sector. November 21, 2006 S29GL-P_00_A3 S29GL-P MirrorBitTM Flash Family 37 Data Sheet (Advance Information) 8.1 Lock Register As shipped from the factory, all devices default to the persistent mode when power is applied, and all sectors are unprotected, unless otherwise chosen through the DYB ordering option (see Ordering Information on page 5). The device programmer or host system must then choose which sector protection method to use. Programming (setting to “0”) any one of the following two one-time programmable, non-volatile bits locks the part permanently in that mode: Lock Register Persistent Protection Mode Lock Bit (DQ1) Lock Register Password Protection Mode Lock Bit (DQ2) Table 8.1 Lock Register DQ15-3 Don’t Care DQ2 Password Protection Mode Lock Bit DQ1 Persistent Protection Mode Lock Bit DQ0 Secured Silicon Sector Protection Bit For programming lock register bits refer to Table 12.2 on page 63 and Table 12.4 on page 65. Notes 1. If the password mode is chosen, the password must be programmed before setting the corresponding lock register bit. 2. After the Lock Register Bits Command Set Entry command sequence is written, reads and writes for Sector 0 are disabled, while reads from other sectors are allowed until exiting this mode. 3. If both lock bits are selected to be programmed (to zeros) at the same time, the operation aborts. 4. Once the Password Mode Lock Bit is programmed, the Persistent Mode Lock Bit is permanently disabled, and no changes to the protection scheme are allowed. Similarly, if the Persistent Mode Lock Bit is programmed, the Password Mode is permanently disabled. After selecting a sector protection method, each sector can operate in any of the following three states: 1. Constantly locked. The selected sectors are protected and can not be reprogrammed unless PPB lock bit is cleared via a password, hardware reset, or power cycle. 2. Dynamically locked. The selected sectors are protected and can be altered via software commands. 3. Unlocked. The sectors are unprotected and can be erased and/or programmed. These states are controlled by the bit types described in Section 8.2–Section 8.5. 8.2 Persistent Protection Bits The Persistent Protection Bits are unique and nonvolatile for each sector and have the same endurances as the Flash memory. Preprogramming and verification prior to erasure are handled by the device, and therefore do not require system monitoring. Notes 1. Each PPB is individually programmed and all are erased in parallel. 2. While programming PPB for a sector, array data can be read from any other sector, except Sector 0 (used for Data# Polling) and the sector in which sector PPB is being programmed. 3. Entry command disables reads and writes for the sector selected. 4. Reads within that sector return the PPB status for that sector. 5. All Reads must be performed using the read mode. 6. The specific sector address (A25-A16 GL01GP, A24-A16 GL512P, A23-A16 GL256P, A22-A16 GL128P) are written at the same time as the program command. 7. If the PPB Lock Bit is set, the PPB Program or erase command does not execute and times-out without programming or erasing the PPB. 38 S29GL-P MirrorBitTM Flash Family S29GL-P_00_A3 November 21, 2006 Data Sheet (Advance Information) 8. There are no means for individually erasing a specific PPB and no specific sector address is required for this operation. 9. Exit command must be issued after the execution which resets the device to read mode and reenables reads and writes for Sector 0. 10. The programming state of the PPB for a given sector can be verified by writing a PPB Status Read Command to the device as described by the flow chart shown in Figure 8.2. Figure 8.2 PPB Program/Erase Algorithm Enter PPB Command Set. Addr = BA Program PPB Bit. Addr = SA Read Byte Twice Addr = SA0 DQ6 = Toggle? Yes No No DQ5 = 1? Yes Read Byte Twice Addr = SA0 Wait 500 µs DQ6 = Toggle? Yes No Read Byte. Addr = SA No DQ0 = '1' (Erase) '0' (Pgm.)? Yes FAIL Issue Reset Command PASS Exit PPB Command Set November 21, 2006 S29GL-P_00_A3 S29GL-P MirrorBitTM Flash Family 39 Data Sheet (Advance Information) 8.2.1 Dynamic Protection Bits Dynamic Protection Bits are volatile and unique for each sector and can be individually modified. DYBs only control the protection scheme for unprotected sectors that have their PPBs cleared (erased to “1”). By issuing the DYB Set or Clear command sequences, the DYBs are set (programmed to “0”) or cleared (erased to “1”), thus placing each sector in the protected or unprotected state respectively. This feature allows software to easily protect sectors against inadvertent changes yet does not prevent the easy removal of protection when changes are needed. Notes 1. The DYBs can be set (programmed to “0”) or cleared (erased to “1”) as often as needed. When the parts are first shipped, the PPBs are cleared (erased to “1”) and upon power up or reset, the DYBs can be set or cleared depending upon the ordering option chosen. 2. If the option to clear the DYBs after power up is chosen, (erased to “1”), then the sectorsmay be modified depending upon the PPB state of that sector (see Table 8.2). 3. The sectors would be in the protected state If the option to set the DYBs after power up is chosen (programmed to “0”). 4. It is possible to have sectors that are persistently locked with sectors that are left in the dynamic state. 5. The DYB Set or Clear commands for the dynamic sectors signify protected or unprotectedstate of the sectors respectively. However, if there is a need to change the status of the persistently locked sectors, a few more steps are required. First, the PPB Lock Bit must be cleared by either putting the device through a power-cycle, or hardware reset. The PPBs can then be changed to reflect the desired settings. Setting the PPB Lock Bit once again locks the PPBs, and the device operates normally again. 6. To achieve the best protection, it is recommended to execute the PPB Lock Bit Set command early in the boot code and protect the boot code by holding WP#/ACC = VIL. Note that the PPB and DYB bits have the same function when WP#/ACC = VHH as they do when ACC =VIH. 8.3 Persistent Protection Bit Lock Bit The Persistent Protection Bit Lock Bit is a global volatile bit for all sectors. When set (programmed to “0”), it locks all PPBs and when cleared (programmed to “1”), allows the PPBs to be changed. There is only one PPB Lock Bit per device. Notes 1. No software command sequence unlocks this bit unless the device is in the password protection mode; only a hardware reset or a power-up clears this bit. 2. The PPB Lock Bit must be set (programmed to “0”) only after all PPBs are configured to the desired settings. 8.4 Password Protection Method The Password Protection Method allows an even higher level of security than the Persistent Sector Protection Mode by requiring a 64-bit password for unlocking the device PPB Lock Bit. In addition to this password requirement, after power up and reset, the PPB Lock Bit is set “0” to maintain the password mode of operation. Successful execution of the Password Unlock command by entering the entire password clears the PPB Lock Bit, allowing for sector PPBs modifications. Notes 1. There is no special addressing order required for programming the password. Once the Password is written and verified, the Password Mode Locking Bit must be set in order to prevent access. 2. The Password Program Command is only capable of programming “0”s. Programming a “1” after a cell is programmed as a “0” results in a time-out with the cell as a “0”. 3. The password is all “1”s when shipped from the factory. 4. All 64-bit password combinations are valid as a password. 40 S29GL-P MirrorBitTM Flash Family S29GL-P_00_A3 November 21, 2006 Data Sheet (Advance Information) 5. There is no means to verify what the password is after it is set. 6. The Password Mode Lock Bit, once set, prevents reading the 64-bit password on the data bus and further password programming. 7. The Password Mode Lock Bit is not erasable. 8. The lower two address bits (A1–A0) are valid during the Password Read, Password Program, and Password Unlock. 9. The exact password must be entered in order for the unlocking function to occur. 10. The Password Unlock command cannot be issued any faster than 1 µs at a time to prevent a hacker from running through all the 64-bit combinations in an attempt to correctly match a password. 11. Approximately 1 µs is required for unlocking the device after the valid 64-bit password is given to the device. 12. Password verification is only allowed during the password programming operation. 13. All further commands to the password region are disabled and all operations are ignored. 14. If the password is lost after setting the Password Mode Lock Bit, there is no way to clear the PPB Lock Bit. 15. Entry command sequence must be issued prior to any of any operation and it disables reads and writes for Sector 0. Reads and writes for other sectors excluding Sector 0 are allowed. 16. If the user attempts to program or erase a protected sector, the device ignores the command and returns to read mode. 17. A program or erase command to a protected sector enables status polling and returns to read mode without having modified the contents of the protected sector. 18. The programming of the DYB, PPB, and PPB Lock for a given sector can be verified by writing individual status read commands DYB Status, PPB Status, and PPB Lock Status to the device. November 21, 2006 S29GL-P_00_A3 S29GL-P MirrorBitTM Flash Family 41 Data Sheet (Advance Information) Figure 8.3 Lock Register Program Algorithm Write Unlock Cycles: Address 555h, Data AAh Address 2AAh, Data 55h Unlock Cycle 1 Unlock Cycle 2 Write Enter Lock Register Command: Address 555h, Data 40h Program Lock Register Data Address XXXh, Data A0h Address XXXh*, Data PD XXXh = Address don’t care Program Data (PD): See text for Lock Register definitions Caution: Lock register can only be progammed once. Wait 4 ms (Recommended) Perform Polling Algorithm (see Write Operation Status flowchart) Yes Done? No DQ5 = 1? Yes No Error condition (Exceeded Timing Limits) PASS. Write Lock Register Exit Command: Address XXXh, Data 90h Address XXXh, Data 00h Device returns to reading array. FAIL. Write rest command to return to reading array. 42 S29GL-P MirrorBitTM Flash Family S29GL-P_00_A3 November 21, 2006 Data Sheet (Advance Information) 8.5 Advanced Sector Protection Software Examples Table 8.2 Sector Protection Schemes: DYB, PPB and PPB Lock Bit Combinations Unique Device PPB Lock Bit 0 = locked 1 = unlocked Any Sector Any Sector Any Sector Any Sector Any Sector Any Sector Any Sector Any Sector 0 0 0 0 1 1 1 1 Sector PPB 0 = protected 1 = unprotected 0 0 1 1 0 0 1 1 Sector DYB 0 = protected 1 = unprotected x x 1 0 x x 0 1 Sector Protection Status Protected through PPB Protected through PPB Unprotected Protected through DYB Protected through PPB Protected through PPB Protected through DYB Unprotected Table 8.2 contains all possible combinations of the DYB, PPB, and PPB Lock Bit relating to the status of the sector. In summary, if the PPB Lock Bit is locked (set to “0”), no changes to the PPBs are allowed. The PPB Lock Bit can only be unlocked (reset to “1”) through a hardware reset or power cycle. See also Figure 8.1 for an overview of the Advanced Sector Protection feature. 8.6 Hardware Data Protection Methods The device offers two main types of data protection at the sector level via hardware control: When WP#/ACC is at VIL, the either the highest or lowest sector is locked (device specific). There are additional methods by which intended or accidental erasure of any sectors can be prevented via hardware means. The following subsections describes these methods: 8.6.1 WP#/ACC Method The Write Protect feature provides a hardware method of protecting one outermost sector. This function is provided by the WP#/ACC pin and overrides the previously discussed Sector Protection/Unprotection method. If the system asserts VIL on the WP#/ACC pin, the device disables program and erase functions in the highest or lowest sector independently of whether the sector was protected or unprotected using the method described in "Advanced Sector Protection/Unprotection" section. If the system asserts VIH on the WP#/ACC pin, the device reverts to whether the boot sectors were last set to be protected or unprotected. That is, sector protection or unprotection for these sectors depends on whether they were last protected or unprotected. Note that the WP#/ACC pin must not be left floating or unconnected as inconsistent behavior of the device may result. The WP#/ACC pin must be held stable during a command sequence execution. Note If WP#/ACC is at VIL when the device is in the standby mode, the maximum input load current is increased. See Table 11.6 on page 50 for details. 8.6.2 Low VCC Write Inhibit When VCC is less than VLKO, the device does not accept any write cycles. This protects data during VCC power-up and power-down. The command register and all internal program/erase circuits are disabled, and the device resets to reading array data. Subsequent writes are ignored until VCC is greater than VLKO. The system must provide the proper signals to the control inputs to prevent unintentional writes when VCC is greater than VLKO. November 21, 2006 S29GL-P_00_A3 S29GL-P MirrorBitTM Flash Family 43 Data Sheet (Advance Information) 8.6.3 Write Pulse “Glitch Protection” Noise pulses of less than 5 ns (typical) on OE#, CE# or WE# do not initiate a write cycle. 8.6.4 Power-Up Write Inhibit If WE# = CE# = RESET# = VIL and OE# = VIH during power up, the device does not accept commands on the rising edge of WE#. The internal state machine is automatically reset to the read mode on power-up. 9. Power Conservation Modes 9.1 Standby Mode When the system is not reading or writing to the device, it can place the device in the standby mode. In this mode, current consumption is greatly reduced, and the outputs are placed in the high impedance state, independent of the OE# input. The device enters the CMOS standby mode when the CE# and RESET# inputs are both held at VCC ± 0.3 V. The device requires standard access time (tCE) for read access, before it is ready to read data. If the device is deselected during erasure or programming, the device draws active current until the operation is completed. ICC4 in “DC Characteristics” represents the standby current specification 9.2 Automatic Sleep Mode The automatic sleep mode minimizes Flash device energy consumption. The device automatically enables this mode when addresses remain stable for tACC + 30 ns. The automatic sleep mode is independent of the CE#, WE#, and OE# control signals. Standard address access timings provide new data when addresses are changed. While in sleep mode, output data is latched and always available to the system. ICC6 in Section 11.6 represents the automatic sleep mode current specification. 9.3 Hardware RESET# Input Operation The RESET# input provides a hardware method of resetting the device to reading array data. When RESET# is driven low for at least a period of tRP, the device immediately terminates any operation in progress, tristates all outputs, and ignores all read/write commands for the duration of the RESET# pulse. The device also resets the internal state machine to reading array data. The operation that was interrupted should be reinitiated once the device is ready to accept another command sequence to ensure data integrity. When RESET# is held at VSS ± 0.3 V, the device draws ICC reset current (ICC5). If RESET# is held at VIL but not within VSS ± 0.3 V, the standby current is greater. RESET# may be tied to the system reset circuitry and thus, a system reset would also reset the Flash memory, enabling the system to read the boot-up firmware from the Flash memory. 9.4 Output Disable (OE#) When the OE# input is at VIH, output from the device is disabled. The outputs are placed in the high impedance state. 44 S29GL-P MirrorBitTM Flash Family S29GL-P_00_A3 November 21, 2006 Data Sheet (Advance Information) 10. Secured Silicon Sector Flash Memory Region The Secured Silicon Sector provides an extra Flash memory region that enables permanent part identification through an Electronic Serial Number (ESN). The Secured Silicon Sector is 128 words in length and all Secured Silicon reads outside of the 128-word address range returns invalid data. The Secured Silicon Sector Indicator Bit, DQ7, (at Autoselect address 03h) is used to indicate whether or not the Secured Silicon Sector is locked when shipped from the factory. Please note the following general conditions: On power-up, or following a hardware reset, the device reverts to sending commands to the normal address space. Reads outside of sector SA0 return memory array data. Sector SA0 is remapped from memory array to Secured Silicon Sector array. Once the Secured Silicon Sector Entry Command is issued, the Secured Silicon Sector Exit command must be issued to exit Secured Silicon Sector Mode. The Secured Silicon Sector is not accessible when the device is executing an Embedded Program or Embedded Erase algorithm. The ACC function and unlock bypass modes are not available when the Secured Silicon Sector is enabled. Table 10.1 Secured Silicon Sector Addresses Secured Silicon Sector Address Range 000000h–000007h 000008h–00007Fh Customer Lockable Determined by customer ESN Factory Locked ESN Unavailable ExpressFlash Factory Locked ESN or determined by customer Determined by customer 10.1 Factory Locked Secured SiliconSector The Secured Silicon Sector is always protected when shipped from the factory and has the Secured Silicon Sector Indicator Bit (DQ7) permanently set to a “1”. This prevents cloning of a factory locked part and ensures the security of the ESN and customer code once the product is shipped to the field. These devices are available pre-programmed with one of the following: A random, 8 Word secure ESN only within the Secured Silicon Sector (at addresses 000000H - 000007H) Both a random, secure ESN and customer code through the Spansion programming service. Customers may opt to have their code programmed through the Spansion programming services. Spansion programs the customer's code, with or without the random ESN. The devices are then shipped from the Spansion factory with the Secured Silicon Sector permanently locked. Contact your local representative for details on using Spansion programming services. 10.2 Customer Lockable Secured Silicon Sector The Secured Silicon Sector is typically shipped unprotected (DQ7 set to “0”), allowing customers to utilize that sector in any manner they choose. If the security feature is not required, the Secured Silicon Sector can be treated as an additional Flash memory space. Please note the following: Once the Secured Silicon Sector area is protected, the Secured Silicon Sector Indicator Bit is permanently set to “0.” The Secured Silicon Sector can be read any number of times, but can be programmed and locked only once. The Secured Silicon Sector lock must be used with caution as once locked, there is no procedure available for unlocking the Secured Silicon Sector area and none of the bits in the Secured Silicon Sector memory space can be modified in any way. The accelerated programming (ACC) and unlock bypass functions are not available when the Secured Silicon Sector is enabled. November 21, 2006 S29GL-P_00_A3 S29GL-P MirrorBitTM Flash Family 45 Data Sheet (Advance Information) Once the Secured Silicon Sector is locked and verified, the system must write the Exit Secured Silicon Sector Region command sequence which return the device to the memory array at sector 0. 10.3 Secured Silicon Sector Entry/Exit Command Sequences The system can access the Secured Silicon Sector region by issuing the three-cycle Enter Secured Silicon Sector command sequence. The device continues to access the Secured Silicon Sector region until the system issues the four-cycle Exit Secured Silicon Sector command sequence. See Command Definition Table [Secured Silicon Sector Command Table, Appendix Table 12.1 on page 61 through Table 12.4 on page 65 for address and data requirements for both command sequences. The Secured Silicon Sector Entry Command allows the following commands to be executed Read customer and factory Secured Silicon areas Program the customer Secured Silicon Sector After the system has written the Enter Secured Silicon Sector command sequence, it may read the Secured Silicon Sector by using the addresses normally occupied by sector SA0 within the memory array. This mode of operation continues until the system issues the Exit Secured Silicon Sector command sequence, or until power is removed from the device. Software Functions and Sample Code The following are C functions and source code examples of using the Secured Silicon Sector Entry, Program, and exit commands. Refer to the Spansion Low Level Driver User’s Guide (available soon on www.spansion.com) for general information on Spansion Flash memory software development guidelines. Table 10.2 Secured Silicon Sector Entry (LLD Function = lld_SecSiSectorEntryCmd) Cycle Unlock Cycle 1 Unlock Cycle 2 Entry Cycle Note Base = Base Address. Operation Write Write Write Byte Address Base + AAAh Base + 555h Base + AAAh Word Address Base + 555h Base + 2AAh Base + 555h Data 00AAh 0055h 0088h /* Example: SecSi Sector *( (UINT16 *)base_addr *( (UINT16 *)base_addr *( (UINT16 *)base_addr Entry Command */ + 0x555 ) = 0x00AA; + 0x2AA ) = 0x0055; + 0x555 ) = 0x0088; /* write unlock cycle 1 /* write unlock cycle 2 /* write Secsi Sector Entry Cmd */ */ */ Table 10.3 Secured Silicon Sector Program (LLD Function = lld_ProgramCmd) Cycle Unlock Cycle 1 Unlock Cycle 2 Program Setup Program Note Base = Base Address. /* Once in the SecSi Sector mode, you program */ /* words using the programming algorithm. */ Operation Write Write Write Write Byte Address Base + AAAh Base + 555h Base + AAAh Word Address Word Address Base + 555h Base + 2AAh Base + 555h Word Address Data 00AAh 0055h 00A0h Data Word 46 S29GL-P MirrorBitTM Flash Family S29GL-P_00_A3 November 21, 2006 Data Sheet (Advance Information) Table 10.4 Secured Silicon Sector Exit (LLD Function = lld_SecSiSectorExitCmd) Cycle Unlock Cycle 1 Unlock Cycle 2 Exit Cycle 3 Exit Cycle 4 Note Base = Base Address. /* Example: SecSi Sector *( (UINT16 *)base_addr *( (UINT16 *)base_addr *( (UINT16 *)base_addr *( (UINT16 *)base_addr Exit Command */ + 0x555 ) = 0x00AA; + 0x2AA ) = 0x0055; + 0x555 ) = 0x0090; + 0x000 ) = 0x0000; Operation Write Write Write Write Byte Address Base + AAAh Base + 555h Base + AAAh Base + AAAh Word Address Base + 555h Base + 2AAh Base + 555h Base + 000h Data 00AAh 0055h 0090h 0000h /* /* /* /* write write write write unlock cycle unlock cycle SecSi Sector SecSi Sector 1 2 Exit cycle 3 Exit cycle 4 */ */ */ */ 11. Electrical Specifications 11.1 Absolute Maximum Ratings Description Storage Temperature, Plastic Packages Ambient Temperature with Power Applied All Inputs and I/Os except as noted below (Note 1) Voltage with Respect to Ground VCC (Note 1) VIO A9 and ACC (Note 2) Output Short Circuit Current (Note 3) Rating –65°C to +150°C –65°C to +125°C –0.5 V to VCC + 0.5 V –0.5 V to +4.0 V –0.5V to +4.0V –0.5 V to +12.5 V 200 mA Notes 1. Minimum DC voltage on input or I/Os is –0.5 V. During voltage transitions, inputs or I/Os may undershoot VSS to –2.0 V for periods of up to 20 ns. See Figure 11.1. Maximum DC voltage on input or I/Os is VCC + 0.5 V. During voltage transitions inputs or I/Os may overshoot to VCC + 2.0 V for periods up to 20 ns. See Figure 11.2. 2. Minimum DC input voltage on pins A9 and ACC is -0.5V. During voltage transitions, A9 and ACC may overshoot VSS to –2.0 V for periods of up to 20 ns. See Figure 11.1. Maximum DC voltage on pins A9 and ACC is +12.5 V, which may overshoot to 14.0 V for periods up to 20 ns. 3. No more than one output may be shorted to ground at a time. Duration of the short circuit should not be greater than one second. 4. Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational sections of this data sheet is not implied. Exposure of the device to absolute maximum rating conditions for extended periods may affect device reliability. Figure 11.1 Maximum Negative Overshoot Waveform 20 ns +0 . 8 V –0 .5 V –2 .0 V 20 n s 20 ns November 21, 2006 S29GL-P_00_A3 S29GL-P MirrorBitTM Flash Family 47 Data Sheet (Advance Information) Figure 11.2 Maximum Positive Overshoot Waveform 20 ns VCC +2.0 V VCC +0.5 V +2.0 V 20 ns 20 ns 11.2 Operating Ranges Specifications Ambient Temperature (TA), Industrial (I) Device Supply Voltages VIO Supply Voltages VCC VIO Range –40°C to +85°C +2.7 V to 3.6 V or +3.0 V to 3.6 V +1.65 V to VCC Notes 1. Operating ranges define those limits between which the functionality of the device is guaranteed. 2. See also Ordering Information on page 5. 3. For valid VCC/VIO range combinations, see Ordering Information on page 5. The I/Os do not operate at 3 V when VIO = 1.8 V. 11.3 Test Conditions Figure 11.3 Test Setup 3.3 V 2.7 kΩ Device Under Test CL 6.2 kΩ Note Diodes are IN3064 or equivalent. 48 S29GL-P MirrorBitTM Flash Family S29GL-P_00_A3 November 21, 2006 Data Sheet (Advance Information) Table 11.1 Test Specifications Test Condition Output Load Output Load Capacitance, CL (including jig capacitance) Input Rise and Fall Times Input Pulse Levels Input timing measurement reference levels (See Note) Output timing measurement reference levels Note If VIO < VCC, the reference level is 0.5 VIO. All Speeds 1 TTL gate 30 5 0.0–VIO 0.5VIO 0.5 VIO Unit pF ns V V V 11.4 Key to Switching Waveforms Waveform Inputs Steady Changing from H to L Changing from L to H Don’t Care, Any Change Permitted Does Not Apply Changing, State Unknown Center Line is High Impedance State (High Z) Outputs 11.5 Switching Waveforms Figure 11.4 Input Waveforms and Measurement Levels VIO 0.0 V Input 0.5 VIO Measurement Level 0.5 VIO V Output Note If VIO < VCC, the input measurement reference level is 0.5 VIO. November 21, 2006 S29GL-P_00_A3 S29GL-P MirrorBitTM Flash Family 49 Data Sheet (Advance Information) 11.6 Parameter Symbol ILI ILIT ILO ICC1 IIO2 ICC2 ICC3 DC Characteristics Table 11.2 S29GL-P DC Characteristics (CMOS Compatible) Parameter Description (Notes) Input Load Current (1) A9 Input Load Current Output Leakage Current Test Conditions VIN = VSS to VCC VCC = VCC max VCC = VCC max; A9 = 12.5 V VOUT = VSS to VCC , VCC = VCC max CE# = VIL, OE# = VIH, VCC = VCCmax, f = 1 MHz VCC Active Read Current (1) VIO Non-Active Output VCC Intra-Page Read Current (1) VCC Active Erase/ Program Current (2, 3) VCC Standby Current CE# = VIL, OE# = VIH, VCC = VCCmax, f = 5 MHz CE# = VIL, OE# = VIH, VCC = VCCmax, f = 10 MHz CE# = VIL, OE# = VIH CE# = VIL, OE# = VIH, VCC = VCCmax, f = 10 MHz CE# = VIL, OE# = VIH, VCC = VCCmax, f = 33 MHz CE# = VIL, OE# = VIH, VCC = VCCmax CE#, RESET# = VCC ± 0.3 V, OE# = VIH, VCC = VCCmax VIL = VSS + 0.3 V/-0.1V, VCC = VCCmax; VIL = VSS + 0.3 V/-0.1V, RESET# = VSS ± 0.3 V VCC = VCCmax, VIH = VCC ± 0.3 V, VIL = VSS + 0.3 V/-0.1V, WP#/ACC = VIH CE# = VIL, OE# = VIH, VCC = VCCmax, WP#/ACC = VHH WP#/ACC pin VCC pin –0.1 0.7 x VIO 11.5 11.5 6 30 60 0.2 1 5 50 WP/ACC Others Min Typ Max ±2.0 ±1.0 35 ±1.0 20 50 100 10 10 20 90 mA mA mA mA µA µA Unit µA ICC4 1 5 µA ICC5 ICC6 VCC Reset Current Automatic Sleep Mode (4) ACC Accelerated Program Current Input Low Voltage (5) Input High Voltage (5) 250 1 10 50 500 5 20 80 0.3 x VIO VIO + 0.3 12.5 12.5 0.15 x VIO µA µA IACC VIL VIH VHH VID VOL VOH VLKO mA V V V V V V Voltage for Program Acceleration VCC = 2.7 –3.6 V Voltage for Autoselect and Temporary Sector Unprotect Output Low Voltage (5) Output High Voltage (5) Low VCC Lock-Out Voltage (3) VCC = 2.7 –3.6 V IOL = 100 µA IOH = -100 µA 0.85 x VIO 2.3 2.5 V Notes 1. The ICC current listed is typically less than 2 mA/MHz, with OE# at VIH. 2. ICC active while Embedded Erase or Embedded Program or Write Buffer Programming is in progress. 3. Not 100% tested. 4. Automatic sleep mode enables the lower power mode when addresses remain stable tor tACC + 30 ns. 5. VIO = 1.65–3.6 V 6. VCC = 3 V and VIO = 3V or 1.8V. When VIO is at 1.8V, I/O pins cannot operate at 3V. 50 S29GL-P MirrorBitTM Flash Family S29GL-P_00_A3 November 21, 2006 Data Sheet (Advance Information) 11.7 AC Characteristics S29GL-P Read-Only Operations Table 11.3 S29GL-P Read-Only Operations Speed Options Test Setup VIO = VCC = 2.7 V VIO = 1.65 V to VCC, VCC = 3 V VIO = VCC = 2.7 V VIO = 1.65 V to VCC, VCC = 3 V VIO = VCC = 2.7 V VIO = 1.65 V to VCC, VCC = 3 V Min 110 110 110 110 110 110 110 25 25 25 30 20 20 0 0 10 35 25 25 120 130 25 30 120 130 110 120 120 130 ns ns ns ns ns ns ns ns ns ns ns ns 130 Unit ns 11.7.1 Parameter JEDEC tAVAV tAVQV tELQV Std. tRC tACC tCE tPACC tGLQV tEHQZ tGHQZ tAXQX tOE tDF tDF tOH Description (Notes) Read Cycle Time Address to Output Delay (1) Max Chip Enable to Output Delay (2) Page Access Time Output Enable to Output Delay Chip Enable to Output High Z (3) Output Enable to Output High Z (3) Output Hold Time From Addresses, CE# or OE#, Whichever Occurs First Read Output Enable Hold Time (3) Chip Enable Hold Time Max Max Max Max Max Min Min Min Min tOEH tCEH Notes 1. CE#, OE# = VIL 2. OE# = VIL 3. Not 100% tested. Toggle and Data# Polling Read 4. See Figure 11.3 and Table 11.1 for test specifications. 5. Unless otherwise indicated, AC specifications for 110 ns speed options are tested with VIO = VCC = 2.7 V. AC specifications for 110 ns speed options are tested with VIO = 1.8 V and VCC = 3.0 V. Figure 11.5 Read Operation Timings tRC Addresses CE# Addresses Stable tACC tCEH tRH tRH OE# tOEH WE# HIGH Z Outputs RESET# RY/BY# Output Valid tCE tOH HIGH Z tOE tDF 0V November 21, 2006 S29GL-P_00_A3 S29GL-P MirrorBitTM Flash Family 51 Data Sheet (Advance Information) Figure 11.6 Page Read Timings Amax:A2 Same Page A2:A0 (See Note) Aa tACC Ab tPACC Ac tPACC tPACC Ad Data Bus CE# OE# Note Figure 11.6 shows word mode. Addresses are A2:A-1 for byte mode. Qa Qb Qc Qd 11.7.2 Parameter JEDEC Hardware Reset (RESET#) Table 11.4 Hardware Reset (RESET#) Std. tReady tReady tRP tRH tRPD tRB Description RESET# Pin Low (During Embedded Algorithms) to Read Mode or Write mode RESET# Pin Low (NOT During Embedded Algorithms) to Read Mode or Write mode RESET# Pulse Width Reset High Time Before Read RESET# Low to Standby Mode RY/BY# Recovery Time Min Min Min Min Min Min Speed 35 35 35 200 10 0 Unit µs µs µs ns µs ns 52 S29GL-P MirrorBitTM Flash Family S29GL-P_00_A3 November 21, 2006 Data Sheet (Advance Information) Figure 11.7 Reset Timings RY/BY# CE#, OE# tRH RESET# tRP tReady Reset Timings NOT during Embedded Algorithms Reset Timings during Embedded Algorithms tReady RY/BY# tRB CE#, OE# RESET# tRP Note CE#, OE# and WE# must be at logic high during Reset Time. Table 11.5 Power-up Sequence Timings Parameter tVCS tVIOS tRH Notes 1. VIO < VCC + 200 mV. 2. VIO and VCC ramp must be synchornized during power up. 3. If RESET# is not stable for tVCS or tVIOS: The device does not permit any read and write operations. A valid read operation returns FFh. A hardware reset is required. 4. VCC maximum power-up current (RST=VIL) is 20 mA. Description Reset Low Time from rising edge of VCC (or last Reset pulse) to rising edge of RESET# Reset Low Time from rising edge of VIO (or last Reset pulse) to rising edge of RESET# Reset High Time before Read Min Min Max Speed 35 35 200 Unit µs µs ns November 21, 2006 S29GL-P_00_A3 S29GL-P MirrorBitTM Flash Family 53 Data Sheet (Advance Information) Figure 11.8 Power-up Sequence Timings VCC VIO CE# VCC min VIO min tRH RESET# tVIOS tVCS 11.7.3 Parameter JEDEC tAVAV tAVWL tWLAX tDVWH tWHDX Std. tWC tAS tASO tAH tAHT tDS tDH tCEPH tOEPH tGHWL tELWL tWHEH tWLWH tWHDL tGHWL tCS tCH tWP tWPH S29GL-P Erase and Program Operations Table 11.6 S29GL-P Erase and Program Operations Speed Options Description Write Cycle Time (Note 1) Address Setup Time Address Setup Time to OE# low during toggle bit polling Address Hold Time Address Hold Time From CE# or OE# high during toggle bit polling Data Setup Time Data Hold Time CE# High during toggle bit polling Output Enable High during toggle bit polling Read Recovery Time Before Write (OE# High to WE# Low) CE# Setup Time CE# Hold Time Write Pulse Width Write Pulse Width High Write Buffer Program Operation (Notes 2, 3) Effective Write Buffer Program Operation (Notes 2, 4) Per Word Per Word Word Word Accelerated Effective Write Buffer Program Operation (Notes 2, 4) Program Operation (Note 2) Accelerated Programming Operation (Note 2) Unit Min Min Min Min Min Min Min Min Min Min Min Min Min Min Typ Typ Typ Typ Typ Typ Min Min Max Max 110 110 (Note 6) 120 120 0 15 45 0 45 0 20 20 0 0 0 35 30 480 15 13.5 60 54 0.5 250 35 90 50 130 130 Unit ns ns ns ns ns ns ns ns ns ns ns ns ns ns µs µs µs µs µs sec ns µs ns µs tWHWH1 tWHWH1 tWHWH2 tWHWH2 Sector Erase Operation (Note 2) tVHH tVCS tBUSY tSEA VHH Rise and Fall Time (Note 1) VCC Setup Time (Note 1) Erase/Program Valid to RY/BY# Delay Command Cycle Timout Notes 1. Not 100% tested. 2. See Section 11.6 for more information. 3. For 1–32 words/1–64 bytes programmed. 4. Effective write buffer specification is based upon a 32-word/64-byte write buffer operation. 5. Unless otherwise indicated, AC specifications for 110 ns speed option are tested with VIO = VCC = 2.7 V. AC specifications for 110 ns speed options are tested with VIO = 1.8 V and VCC = 3.0 V. 6. Write Cycle Time = Access Time at VCC. 54 S29GL-P MirrorBitTM Flash Family S29GL-P_00_A3 November 21, 2006 Data Sheet (Advance Information) Figure 11.9 Program Operation Timings Program Command Sequence (last two cycles) tWC Addresses 555h tAS PA tAH CE# OE# tWP WE# tCS tDS Data tDH PD tBUSY RY/BY# tWPH Read Status Data (last two cycles) PA PA tCH tWHWH1 A0h Status DOUT tRB VCC tVCS Notes 1. PA = program address, PD = program data, DOUT is the true data at the program address. 2. Illustration shows device in word mode. Figure 11.10 Accelerated Program Timing Diagram VHH ACC VIL or VIH tVHH tVHH VIL or VIH Notes 1. Not 100% tested. 2. CE#, OE# = VIL 3. OE# = VIL 4. See Figure 11.3 and Table 11.1 for test specifications. November 21, 2006 S29GL-P_00_A3 S29GL-P MirrorBitTM Flash Family 55 Data Sheet (Advance Information) Figure 11.11 Chip/Sector Erase Operation Timings Erase Command Sequence (last two cycles) tWC Addresses 2AAh tAS SA 555h for chip erase Read Status Data VA tAH VA CE# OE# tWP WE# tCS tDS tCH tWPH tWHWH2 tDH Data 55h 30h 10 for Chip Erase In Progress Complete tBUSY RY/BY# tVCS VCC Notes 1. SA = sector address (for Sector Erase), VA = Valid Address for reading status data (see “Write Operation Status.” 2. These waveforms are for the word mode tRB Figure 11.12 Data# Polling Timings (During Embedded Algorithms) tRC Addresses VA tACC tCE CE# tCH OE# tOEH WE# tOH DQ7 High Z VA VA tOE tDF Complement Complement True Valid Data High Z DQ6–DQ0 tBUSY RY/BY# Status Data Status Data True Valid Data Notes 1. VA = Valid address. Illustration shows first status cycle after command sequence, last status read cycle, and array data read cycle. 2. tOE for data polling is 45 ns when VIO = 1.65 to 2.7 V and is 35 ns when VIO = 2.7 to 3.6 V 56 S29GL-P MirrorBitTM Flash Family S29GL-P_00_A3 November 21, 2006 Data Sheet (Advance Information) Figure 11.13 Toggle Bit Timings (During Embedded Algorithms) tAHT Addresses tAHT tASO CE# tOEH WE# tOEPH OE# tDH DQ2 and DQ6 Valid Data Valid Status tAS tCEPH tOE Valid Status Valid Status Valid Data (first read) RY/BY# (second read) (stops toggling) Note A = Valid address; not required for DQ6. Illustration shows first two status cycle after command sequence, last status read cycle, and array data read cycle Figure 11.14 DQ2 vs. DQ6 Enter Embedded Erasing WE# Erase Suspend Erase Enter Erase Suspend Program Erase Suspend Program Erase Resume Erase Suspend Read Erase Erase Complete Erase Suspend Read DQ6 DQ2 Note DQ2 toggles only when read at an address within an erase-suspended sector. The system can use OE# or CE# to toggle DQ2 and DQ6. November 21, 2006 S29GL-P_00_A3 S29GL-P MirrorBitTM Flash Family 57 Data Sheet (Advance Information) 11.7.4 Parameter JEDEC tAVAV tAVWL tELAX tDVEH tEHDX Std. tWC tAS tASO tAH tAHT tDS tDH S29GL-P Alternate CE# Controlled Erase and Program Operations Table 11.7 S29GL-P Alternate CE# Controlled Erase and Program Operations Description (Notes) Write Cycle Time (Note 1) Address Setup Time Address Setup Time to OE# low during toggle bit polling Address Hold Time Address Hold Time From CE# or OE# high during toggle bit polling Data Setup Time Data Hold Time CE# High during toggle bit polling OE# High during toggle bit polling Read Recovery Time Before Write (OE# High to WE# Low) WE# Setup Time WE# Hold Time CE# Pulse Width CE# Pulse Width High Write Buffer Program Operation (Notes 2, 3) Effective Write Buffer Program Operation (Notes 2, 4) Effective Accelerated Write Buffer Program Operation (Notes 2, 4) Program Operation (Note 2) Accelerated Programming Operation (Note 2) Per Word Per Word Word Word Min Min Min Min Min Min Min Min Min Min Min Min Min Min Typ Typ Typ Typ Typ Typ Speed Options 110 110 (Note 6) 120 120 0 15 45 0 45 0 20 20 0 0 0 35 30 480 15 13.5 60 54 0.5 130 130 Unit ns ns ns ns ns ns ns ns ns ns ns ns ns ns µs µs µs µs µs sec tCEPH tOEPH tGHEL tWLEL tEHWH tELEH tEHEL tWHWH1 tGHEL tWS tWH tCP tCPH tWHWH1 tWHWH2 tWHWH2 Sector Erase Operation (Note 2) Notes 1. Not 100% tested. 2. See the “AC Characteristics” section for more information. 3. For 1–32 words/1–64 bytes programmed. 4. Effective write buffer specification is based upon a 32-word/64-byte write buffer operation. 5. Unless otherwise indicated, AC specifications are tested with VIO = 1.8 V and VCC = 3.0 V 6. Write Cycle Time = Access Time at VCC. 58 S29GL-P MirrorBitTM Flash Family S29GL-P_00_A3 November 21, 2006 Data Sheet (Advance Information) Figure 11.15 Alternate CE# Controlled Write (Erase/Program) Operation Timings 555 for program 2AA for erase PA for program SA for sector erase 555 for chip erase Data# Polling PA Addresses tWC tWH WE# tGHEL OE# tCP CE# tWS tCPH tDS tDH Data tRH A0 for program 55 for erase PD for program 30 for sector erase 10 for chip erase tAS tAH tWHWH1 or 2 tBUSY DQ7# DOUT RESET# RY/BY# Notes 1. Figure 11.15 indicates last two bus cycles of a program or erase operation. 2. PA = program address, SA = sector address, PD = program data. 3. DQ7# is the complement of the data written to the device. DOUT is the data written to the device. 4. Waveforms are for the word mode. November 21, 2006 S29GL-P_00_A3 S29GL-P MirrorBitTM Flash Family 59 Data Sheet (Advance Information) 11.7.5 Erase And Programming Performance Table 11.8 Erase And Programming Performance Parameter Typ (Note 1) 0.5 S29GL128P 64 128 256 512 480 432 123 246 492 984 sec Max (Note 2) 3.5 256 512 1024 2048 µs µs Excludes system level overhead (Note 6) sec Excludes 00h programming prior to erasure (Note 5) Unit sec Comments Sector Erase Time Chip Erase Time S29GL256P S29GL512P S29GL01GP Total Write Buffer Time (Note 3) Total Accelerated Write Buffer Programming Time (Note 3) S29GL128P Chip Program Time (Note 4) S29GL256P S29GL512P S29GL01GP Notes 1. Typical program and erase times assume the following conditions: 25°C, 3.6 V VCC, 10,000 cycles, checkerboard pattern. 2. Under worst case conditions of -40°C, VCC = 3.0 V, 100,000 cycles. 3. Effective write buffer specification is based upon a 32-word write buffer operation. 4. The typical chip programming time is considerably less than the maximum chip programming time listed, since most words program faster than the maximum program times listed. 5. In the pre-programming step of the Embedded Erase algorithm, all bits are programmed to 00h before erasure. 6. System-level overhead is the time required to execute the two- or four-bus-cycle sequence for the program command. See Tables 12.1–12.4. 11.7.6 TSOP Pin and BGA Package Capacitance Table 1: Parameter Symbol CIN COUT CIN2 Notes 1. Sampled, not 100% tested. Parameter Description Input Capacitance VIN = 0 Test Setup TSOP BGA TSOP BGA TSOP BGA Typ 6 4.2 8.5 5.4 7.5 3.9 Max 7.5 5.0 12 6.5 9 4.7 Unit pF pF pF pF pF pF Output Capacitance VOUT = 0 VIN = 0 Control Pin Capacitance 2. Test conditions TA = 25°C, f = 1.0 MHz. 60 S29GL-P MirrorBitTM Flash Family S29GL-P_00_A3 November 21, 2006 Data Sheet (Advance Information) 12. Appendix This section contains information relating to software control or interfacing with the Flash device. For additional information and assistance regarding software, see Section 5. For the latest information, explore the Spansion web site at www.spansion.com. 12.1 Command Definitions Writing specific address and data commands or sequences into the command register initiates device operations. Tables 12.1–12.4 define the valid register command sequences. Writing incorrect address and data values or writing them in the improper sequence can place the device in an unknown state. A reset command is then required to return the device to reading array data. Table 12.1 S29GL-P Memory Array Command Definitions, x16 Cycles Bus Cycles (Notes 1–5) First Addr RA XXX 555 555 555 555 55 555 555 SA 555 555 XXX XXX XXX XXX 555 555 XXX XXX 555 555 Data RD F0 AA AA AA AA 98 AA AA 29 AA AA A0 80 80 90 AA AA B0 30 AA AA 2AA 2AA 55 55 555 555 88 90 XX 00 2AA 2AA PA SA XXX XXX 2AA 2AA 55 55 PD 30 10 00 55 55 555 555 80 80 555 555 AA AA 2AA 2AA 55 55 555 SA 10 30 555 555 F0 20 2AA 2AA 55 55 555 SA A0 25 PA SA PD WC WBL PD WBL PD 2AA 2AA 2AA 2AA 55 55 55 55 555 555 555 555 90 90 90 90 X00 X01 [SA]X02 X03 01 227E (10) (11) X0E (8) X0F (8) Second Addr Data Third Addr Data Fourth Addr Data Fifth Addr Data Sixth Addr Data Command (Notes) Read (6) Reset (7) Autoselect (8,9) Manufacturer ID Device ID (8) Sector Protect Verify (10) Secure Device Verify (11) 1 1 4 4 4 4 1 4 3 1 3 3 2 2 2 2 6 6 1 1 3 4 CFI Query (12) Program Write to Buffer Program Buffer to Flash (Confirm) Write-to-Buffer-Abort Reset (13) Unlock Bypass Enter Program (14) Sector Erase (14) Chip Erase (14) Reset (15) Chip Erase Sector Erase Erase Suspend/Program Suspend (16) Erase Resume/Program Resume (17) Secured Silicon Sector Entry Secured Silicon Sector Exit (18) Legend X = Don’t care RA = Address of the memory to be read. RD = Data read from location RA during read operation. PA = Address of the memory location to be programmed. Addresses latch on the falling edge of the WE# or CE# pulse, whichever happens later. PD = Data to be programmed at location PA. Data latches on the rising edge of the WE# or CE# pulse, whichever happens first. SA = Address of the sector to be verified (in autoselect mode) or erased. Address bits Amax–A16 uniquely select any sector. WBL = Write Buffer Location. The address must be within the same write buffer page as PA. WC = Word Count is the number of write buffer locations to load minus 1. Notes 1. See Table 7.1 on page 14 for description of bus operations. 2. All values are in hexadecimal. 3. All bus cycles are write cycles unless otherwise noted. 4. Data bits DQ15-DQ8 are don’t cares for unlock and command cycles. 5. Address bits AMAX:A16 are don’t cares for unlock and command cycles, unless SA or PA required. (AMAX is the Highest Address pin.). 6. No unlock or command cycles required when reading array data. November 21, 2006 S29GL-P_00_A3 S29GL-P MirrorBitTM Flash Family 61 Data Sheet (Advance Information) 7. The Reset command is required to return to reading array data when device is in the autoselect mode, or if DQ5 goes high (while the device is providing status data). 8. See Table 7.2 on page 17 for device ID values and definitions. 9. The fourth, fifth, and sixth cycles of the autoselect command sequence are read cycles. 10. The data is 00h for an unprotected sector and 01h for a protected sector. See “Autoselect Command Sequence” for more information. This is same as PPB Status Read except that the protect and unprotect statuses are inverted here. 11. The data value for DQ7 is “1” for a serialized, protected Secured Silicon Sector region and “0” for an unserialized, unprotected region. See Table 7.3 on page 17 for data and definitions. 12. Command is valid when device is ready to read array data or when device is in autoselect mode. 13. Command sequence returns device to reading array after being placed in a Write-to-Buffer-Abort state. Full command sequence is required if resetting out of abort while in Unlock Bypass mode. 14. The Unlock-Bypass command is required prior to the Unlock-Bypass-Program command. 15. The Unlock-Bypass-Reset command is required to return to reading array data when the device is in the unlock bypass mode. 16. The system can read and program/program suspend in non-erasing sectors, or enter the autoselect mode, when in the Erase Suspend mode. The Erase Suspend command is valid only during a sector erase operation. 17. The Erase Resume/Program Resume command is valid only during the Erase Suspend/Program Suspend modes. 18. The Exit command returns the device to reading the array. 62 S29GL-P MirrorBitTM Flash Family S29GL-P_00_A3 November 21, 2006 Data Sheet (Advance Information) Table 12.2 S29GL-P Sector Protection Command Definitions, x16 Cycles Bus Cycles (Notes 1–5) First/Seventh Addr 555 XXX 77h XXX 555 XXX 00 00 Password Unlock (10) Command Set Exit (7, 8) PPB Command Set Entry Global Non-Volatile PPB Program (11, 12) All PPB Erase (13) PPB Status Read (12) PPB Command Set Exit (7, 8) Global NonVolatile Freeze PPB Lock Command Set Entry PPB Lock Set (12) PPB Lock Status Read (12) PPB Lock Command Set Exit (7, 8) DYB Command Set Entry Volatile DYB Set (11, 12) DYB Clear (12) DYB Status Read (12) DYB Command Set Exit (7, 8) 7 00 2 3 2 2 1 2 3 2 1 2 3 2 2 1 2 XXX 555 XXX XXX SA XXX 555 XXX XXX XXX 555 XXX XXX SA XXX 29 90 AA A0 80 RD (0) 90 AA A0 RD (0) 90 AA A0 A0 RD (0) 90 XXX 00 XXX 2AA SA SA 00 55 00 01 555 E0 XXX 2AA XXX 00 55 00 555 50 XXX 2AA SA 00 00 55 00 30 555 C0 Data AA A0 DATA 90 AA A0 PWD0 25 XXX 2AA PWA x 01 00 00 55 PWD x PWD 1 03 02 00 PWD 2 PWD 0 03 01 PWD 3 PWD 1 02 PWD 2 03 PWD 3 555 60 Second Addr 2AA XXX Data 55 DATA Third Addr 555 Data 40 Fourth Addr Data Fifth Addr Data Sixth Addr Data Command (Notes) Command Set Entry Lock Register Program (6) Read (6) Command Set Exit (7, 8) Command Set Entry Password Program (9) Password Protection Password Read (10) 3 2 1 2 3 2 4 Legend X = Don’t care RD(0) = Read data. SA = Sector Address. Address bits Amax–A16 uniquely select any sector. PWD = Password PWDx = Password word0, word1, word2, and word3. Data = Lock Register Contents: PD(0) = Secured Silicon Sector Protection Bit, PD(1) = Persistent Protection Mode Lock Bit, PD(2) = Password Protection Mode Lock Bit. Notes 1. See Table 7.1 on page 14 for description of bus operations. 2. All values are in hexadecimal. 3. All bus cycles are write cycles unless otherwise noted. 4. Data bits DQ15-DQ8 are don’t cares for unlock and command cycles. 5. Address bits AMAX:A16 are don’t cares for unlock and command cycles, unless SA or PA required. (AMAX is the Highest Address pin.) 6. All Lock Register bits are one-time programmable. Program state = “0” and the erase state = “1.” The Persistent Protection Mode Lock Bit and the Password Protection Mode Lock Bit cannot be programmed at the same time or the Lock Register Bits Program operation aborts and returns the device to read mode. Lock Register bits that are reserved for future use default to “1’s.” The Lock Register is shipped out as “FFFF’s” before Lock Register Bit program execution. 7. The Exit command returns the device to reading the array. 8. If any Command Set Entry command was written, an Exit command must be issued to reset the device into read mode. 9. For PWDx, only one portion of the password can be programmed per each “A0” command. 10. Note that the password portion can be entered or read in any order as long as the entire 64-bit password is entered or read. 11. If ACC = VHH, sector protection matches when ACC = VIH. 12. Protected State = “00h,” Unprotected State = “01h.” 13. The All PPB Erase command embeds programming of all PPB bits before erasure. November 21, 2006 S29GL-P_00_A3 S29GL-P MirrorBitTM Flash Family 63 Data Sheet (Advance Information) Table 12.3 S29GL-P Memory Array Command Definitions, x8 Cycles Bus Cycles (Notes 1–5) First Addr RA XXX AAA AAA AAA AAA AA AAA AAA SA AAA AAA XXX XXX XXX XXX AAA AAA XXX XXX AAA AAA Data RD F0 AA AA AA AA 98 AA AA 29 AA AA A0 80 80 90 AA AA B0 30 AA AA 555 555 55 55 AAA AAA 88 90 XX 00 555 555 PA SA XXX XXX 555 555 55 55 PD 30 10 00 55 55 AAA AAA 80 80 AAA AAA AA AA 555 555 55 55 AAA SA 10 30 555 AAA F0 20 555 555 55 55 AAA SA A0 25 PA SA PD WC WBL PD WBL PD 555 555 555 555 55 55 55 55 AAA AAA AAA AAA 90 90 90 90 X00 X02 [SA]X04 X06 01 XX7E (10) (11) X1C (8) X1E (8) Second Addr Data Third Addr Data Fourth Addr Data Fifth Addr Data Sixth Addr Data Command (Notes) Read (6) Reset (7) Autoselect (8,9) Manufacturer ID Device ID (8) Sector Protect Verify (10) Secure Device Verify (11) 1 1 4 4 4 4 1 4 3 1 3 3 2 2 2 2 6 6 1 1 3 4 CFI Query (12) Program Write to Buffer Program Buffer to Flash (confirm) Write-to-Buffer-Abort Reset (13) Unlock Bypass Enter Program (14) Sector Erase (14) Chip Erase (14) Reset (15) Chip Erase Sector Erase Erase Suspend/Program Suspend (16) Erase Resume/Program Resume (17) Secured Silicon Sector Entry Secured Silicon Sector Exit (18) Legend X = Don’t care RA = Address of the memory to be read. RD = Data read from location RA during read operation. PA = Address of the memory location to be programmed. Addresses latch on the falling edge of the WE# or CE# pulse, whichever happens later. PD = Data to be programmed at location PA. Data latches on the rising edge of the WE# or CE# pulse, whichever happens first. SA = Address of the sector to be verified (in autoselect mode) or erased. Address bits Amax–A16 uniquely select any sector. WBL = Write Buffer Location. The address must be within the same write buffer page as PA. WC = Word Count is the number of write buffer locations to load minus 1. Notes 1. See Table 7.1 on page 14 for description of bus operations. 2. All values are in hexadecimal. 3. All bus cycles are write cycles unless otherwise noted. 4. Data bits DQ15-DQ8 are don’t cares for unlock and command cycles. 5. Address bits AMAX:A16 are don’t cares for unlock and command cycles, unless SA or PA required. (AMAX is the Highest Address pin.). 6. No unlock or command cycles required when reading array data. 7. The Reset command is required to return to reading array data when device is in the autoselect mode, or if DQ5 goes high (while the device is providing status data). 8. See Table 7.2 on page 17 for device ID values and definitions. 9. The fourth, fifth, and sixth cycles of the autoselect command sequence are read cycles. 10. The data is 00h for an unprotected sector and 01h for a protected sector. See “Autoselect Command Sequence” for more information. This is same as PPB Status Read except that the protect and unprotect statuses are inverted here. 11. The data value for DQ7 is “1” for a serialized, protected Secured Silicon Sector region and “0” for an unserialized, unprotected region. See Table 7.3 on page 17 for data and definitions. 12. Command is valid when device is ready to read array data or when device is in autoselect mode. 13. Command sequence returns device to reading array after being placed in a Write-to-Buffer-Abort state. Full command sequence is required if resetting out of abort while in Unlock Bypass mode. 14. The Unlock-Bypass command is required prior to the Unlock-Bypass-Program command. 15. The Unlock-Bypass-Reset command is required to return to reading array data when the device is in the unlock bypass mode. 16. The system can read and program/program suspend in non-erasing sectors, or enter the autoselect mode, when in the Erase Suspend mode. The Erase Suspend command is valid only during a sector erase operation. 17. The Erase Resume/Program Resume command is valid only during the Erase Suspend/Program Suspend modes. 18. The Exit command returns the device to reading the array. 64 S29GL-P MirrorBitTM Flash Family S29GL-P_00_A3 November 21, 2006 Data Sheet (Advance Information) Table 12.4 S29GL-P Sector Protection Command Definitions, x8 Cycles Bus Cycles (Notes 1–5) First/Seventh Addr AAA XXX 00 XXX AAA XXX 00 06 00 Password Unlock (10) 11 04 Command Set Exit (7, 8) PPB Command Set Entry Global Non-Volatile PPB Program (11, 12) All PPB Erase (13) PPB Status Read (12) PPB Command Set Exit (7, 8) Global NonVolatile Freeze PPB Lock Command Set Entry PPB Lock Bit Set (12) PPB Lock Status Read (12) PPB Lock Command Set Exit (7, 8) DYB Command Set Entry Volatile DYB Set (11, 12) DYB Clear (12) DYB Status Read (12) DYB Command Set Exit (7, 8) 2 3 2 2 1 2 3 2 1 2 3 2 2 1 2 XXX AAA XXX XXX SA XXX AAA XXX XXX XXX AAA XXX XXX SA XXX PWD 4 90 AA A0 80 RD(0) 90 AA A0 RD(0) 90 AA A0 A0 RD(0) 90 XXX 00 XXX 555 SA SA 00 55 00 01 AAA E0 XXX 555 XXX 00 55 00 AAA 50 05 XXX 55 SA 00 PWD 5 00 55 00 30 AAA C0 06 PWD 6 07 Data AA A0 DATA 90 AA A0 PWD0 PWD 6 25 XXX 555 PWA x 01 07 00 00 55 PWD x PWD 1 PWD 7 03 00 PWD 0 01 PWD 1 PWD 7 02 00 PWD 2 29 03 PWD 3 02 PWD 2 03 PWD 3 04 PWD 4 05 PWD 5 AAA 60 Second/Eighth Addr 555 XXX Data 55 DATA Third Addr AAA Data 40 Fourth Addr Data Fifth Addr Data Sixth Addr Data Command (Notes) Lock Register Command Set Entry Bits Program (6) Read (6) Command Set Exit (7, 8) Command Set Entry Password Program (9) Password Protection 3 2 1 2 3 2 Password Read (10) 8 Legend X = Don’t care RD(0) = Read data. SA = Sector Address. Address bits Amax–A16 uniquely select any sector. PWD = Password PWDx = Password word0, word1, word2, and word3. Data = Lock Register Contents: PD(0) = Secured Silicon Sector Protection Bit, PD(1) = Persistent Protection Mode Lock Bit, PD(2) = Password Protection Mode Lock Bit. Notes 1. See Table 7.1 on page 14 for description of bus operations. 2. All values are in hexadecimal. 3. All bus cycles are write cycles unless otherwise noted. 4. Data bits DQ15-DQ8 are don’t cares for unlock and command cycles. 5. Address bits AMAX:A16 are don’t cares for unlock and command cycles, unless SA or PA required. (AMAX is the Highest Address pin.) 6. All Lock Register bits are one-time programmable. Program state = “0” and the erase state = “1.” The Persistent Protection Mode Lock Bit and the Password Protection Mode Lock Bit cannot be programmed at the same time or the Lock Register Bits Program operation aborts and returns the device to read mode. Lock Register bits that are reserved for future use default to “1’s.” The Lock Register is shipped out as “FFFF’s” before Lock Register Bit program execution. 7. The Exit command returns the device to reading the array. 8. If any Command Set Entry command was written, an Exit command must be issued to reset the device into read mode. 9. For PWDx, only one portion of the password can be programmed per each “A0” command. 10. Note that the password portion can be entered or read in any order as long as the entire 64-bit password is entered or read. 11. If ACC = VHH, sector protection matches when ACC = VIH. 12. Protected State = “00h,” Unprotected State = “01h.” 13. The All PPB Erase command embeds programming of all PPB bits before erasure. November 21, 2006 S29GL-P_00_A3 S29GL-P MirrorBitTM Flash Family 65 Data Sheet (Advance Information) 12.2 Common Flash Memory Interface The Common Flash Interface (CFI) specification outlines device and host system software interrogation handshake, which allows specific vendor-specified software algorithms to be used for entire families of devices. Software support can then be device-independent, JEDEC ID-independent, and forward- and backward-compatible for the specified flash device families. Flash vendors can standardize their existing interfaces for long-term compatibility. This device enters the CFI Query mode when the system writes the CFI Query command, 98h, to address 55h any time the device is ready to read array data. The system can read CFI infomation at the addresses given in Tables 12.6–12.8). All reads outside of the CFI address range, returns non-valid data. Reads from other sectors are allowed, writes are not. To terminate reading CFI data, the system must write the reset command. The system can also write the CFI query command when the device is in the autoselect mode. The device enters the CFI query mode, and the system can read CFI data at the addresses given in Tables 12.6–12.8. The system must write the reset command to return the device to reading array data. The following is a C source code example of using the CFI Entry and Exit functions. Refer to the Spansion Low Level Driver User’s Guide (available on www.spansion.com) for general information on Spansion Flash memory software development guidelines. /* Example: CFI Entry command */ *( (UINT16 *)base_addr + 0x55 ) = 0x0098; /* Example: CFI Exit command */ *( (UINT16 *)base_addr + 0x000 ) = 0x00F0; /* write CFI entry command */ /* write cfi exit command */ For further information, please refer to the CFI Specification (see JEDEC publications JEP137-A and JESD68.01and CFI Publication 100). Please contact your sales office for copies of these documents. Table 12.5 CFI Query Identification String Addresses (x16) 10h 11h 12h 13h 14h 15h 16h 17h 18h 19h 1Ah Addresses (x8) 20h 22h 24h 26h 28h 2Ah 2Ch 2Eh 30h 32h 34h Data 0051h 0052h 0059h 0002h 0000h 0040h 0000h 0000h 0000h 0000h 0000h Description Query Unique ASCII string “QRY” Primary OEM Command Set Address for Primary Extended Table Alternate OEM Command Set (00h = none exists) Address for Alternate OEM Extended Table (00h = none exists) 66 S29GL-P MirrorBitTM Flash Family S29GL-P_00_A3 November 21, 2006 Data Sheet (Advance Information) Table 12.6 System Interface String Addresses (x16) 1Bh 1Ch 1Dh 1Eh 1Fh 20h 21h 22h 23h 24h 25h 26h Addresses (x8) 36h 38h 3Ah 3Ch 3Eh 40h 42h 44h 46h 48h 4Ah 4Ch Data 0027h 0036h 0000h 0000h 0006h 0006h 0009h 0013h 0003h 0005h 0003h 0002h Description VCC Min. (write/erase) D7–D4: volt, D3–D0: 100 mV VCC Max. (write/erase) D7–D4: volt, D3–D0: 100 mV VPP Min. voltage (00h = no VPP pin present) VPP Max. voltage (00h = no VPP pin present) Typical timeout per single byte/word write 2N µs Typical timeout for Min. size buffer write 2N µs (00h = not supported) Typical timeout per individual block erase 2N ms Typical timeout for full chip erase 2N ms (00h = not supported) Max. timeout for byte/word write 2N times typical Max. timeout for buffer write 2N times typical Max. timeout per individual block erase 2N times typical Max. timeout for full chip erase 2N times typical (00h = not supported) Table 12.7 Device Geometry Definition Addresses (x16) Addresses (x8) Data 001Bh 001Ah 0019h 0018h 0002h 0000h 0006h 0000h 0001h Device Size = 2N byte 1B = 1 Gb, 1A= 512 Mb, 19 = 256 Mb, 18 = 128 Mb Flash Device Interface description (refer to CFI publication 100) Max. number of byte in multi-byte write = 2N (00h = not supported) Number of Erase Block Regions within device (01h = uniform device, 02h = boot device) Erase Block Region 1 Information (refer to the CFI specification or CFI publication 100) 00FFh, 0003h, 0000h, 0002h =1 Gb 00FFh, 0001h, 0000h, 0002h = 512 Mb 00FFh, 0000h, 0000h, 0002h = 256 Mb 007Fh, 0000h, 0000h, 0002h = 128 Mb Description 27h 4Eh 28h 29h 2Ah 2Bh 2Ch 50h 52h 54h 56h 58h 2Dh 2Eh 2Fh 30h 31h 32h 33h 34h 35h 36h 37h 38h 39h 3Ah 3Bh 3Ch 5Ah 5Ch 5Eh 60h 60h 64h 66h 68h 6Ah 6Ch 6Eh 70h 72h 74h 76h 78h 00xxh 000xh 0000h 000xh 0000h 0000h 0000h 0000h 0000h 0000h 0000h 0000h 0000h 0000h 0000h 0000h Erase Block Region 2 Information (refer to CFI publication 100) Erase Block Region 3 Information (refer to CFI publication 100) Erase Block Region 4 Information (refer to CFI publication 100) November 21, 2006 S29GL-P_00_A3 S29GL-P MirrorBitTM Flash Family 67 Data Sheet (Advance Information) Table 12.8 Primary Vendor-Specific Extended Query Addresses (x16) 40h 41h 42h 43h 44h 45h Addresses (x8) 80h 82h 84h 86h 88h 8Ah Data 0050h 0052h 0049h 0031h 0033h 0014h Query-unique ASCII string “PRI” Major version number, ASCII Minor version number, ASCII Address Sensitive Unlock (Bits 1-0) 0 = Required, 1 = Not Required Process Technology (Bits 7-2) 0101b = 90 nm MirrorBit 46h 47h 48h 49h 4Ah 4Bh 4Ch 4Dh 4Eh 8Ch 8Eh 90h 92h 94h 96h 98h 9Ah 9Ch 0002h 0001h 0000h 0008h 0000h 0000h 0002h 00B5h 00C5h Erase Suspend 0 = Not Supported, 1 = To Read Only, 2 = To Read & Write Sector Protect 0 = Not Supported, X = Number of sectors in per group Sector Temporary Unprotect 00 = Not Supported, 01 = Supported Sector Protect/Unprotect scheme 0008h = Advanced Sector Protection Simultaneous Operation 00 = Not Supported, X = Number of Sectors Burst Mode Type 00 = Not Supported, 01 = Supported Page Mode Type 00 = Not Supported, 01 = 4 Word Page, 02 = 8 Word Page ACC (Acceleration) Supply Minimum 00h = Not Supported, D7-D4: Volt, D3-D0: 100 mV ACC (Acceleration) Supply Maximum 00h = Not Supported, D7-D4: Volt, D3-D0: 100 mV WP# Protection 4Fh 9Eh 00xxh 04h = Uniform sectors bottom WP# protect, 05h = Uniform sectors top WP# protect Program Suspend 00h = Not Supported, 01h = Supported Description 50h A0h 0001h 68 S29GL-P MirrorBitTM Flash Family S29GL-P_00_A3 November 21, 2006 Data Sheet (Advance Information) 13. Revision Summary Section Revision A0 (October 29, 2004) Initial Release. Revision A1 (October 20, 2005) Global Revision A2 (October 19, 2006) Global Revision A3 (November 21, 2006) AC Characteristics Erase and Program Operations table: Changed tBUSY to a maximum specification. Revised all sections of document. Reformatted document to new template. Changed speed options for S29GL01GP. Revised all sections of document. Description Colophon The products described in this document are designed, developed and manufactured as contemplated for general use, including without limitation, ordinary industrial use, general office use, personal use, and household use, but are not designed, developed and manufactured as contemplated (1) for any use that includes fatal risks or dangers that, unless extremely high safety is secured, could have a serious effect to the public, and could lead directly to death, personal injury, severe physical damage or other loss (i.e., nuclear reaction control in nuclear facility, aircraft flight control, air traffic control, mass transport control, medical life support system, missile launch control in weapon system), or (2) for any use where chance of failure is intolerable (i.e., submersible repeater and artificial satellite). Please note that Spansion will not be liable to you and/or any third party for any claims or damages arising in connection with above-mentioned uses of the products. Any semiconductor devices have an inherent chance of failure. You must protect against injury, damage or loss from such failures by incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and prevention of over-current levels and other abnormal operating conditions. If any products described in this document represent goods or technologies subject to certain restrictions on export under the Foreign Exchange and Foreign Trade Law of Japan, the US Export Administration Regulations or the applicable laws of any other country, the prior authorization by the respective government entity will be required for export of those products. Trademarks and Notice The contents of this document are subject to change without notice. This document may contain information on a Spansion product under development by Spansion. Spansion reserves the right to change or discontinue work on any product without notice. The information in this document is provided as is without warranty or guarantee of any kind as to its accuracy, completeness, operability, fitness for particular purpose, merchantability, non-infringement of third-party rights, or any other warranty, express, implied, or statutory. Spansion assumes no liability for any damages of any kind arising out of the use of the information in this document. Copyright © 2004–2006 Spansion Inc. All Rights Reserved. Spansion, the Spansion logo, MirrorBit, ORNAND, HD-SIM, and combinations thereof are trademarks of Spansion Inc. Other names are for informational purposes only and may be trademarks of their respective owners. November 21, 2006 S29GL-P_00_A3 S29GL-P MirrorBitTM Flash Family 69