0
登录后你可以
  • 下载海量资料
  • 学习在线课程
  • 观看技术视频
  • 写文章/发帖/加入社区
会员中心
创作中心
发布
  • 发文章

  • 发资料

  • 发帖

  • 提问

  • 发视频

创作活动
CY28439-2

CY28439-2

  • 厂商:

    SPECTRALINEAR

  • 封装:

  • 描述:

    CY28439-2 - Clock Generator for Intel Grantsdale Chipset - SpectraLinear Inc

  • 数据手册
  • 价格&库存
CY28439-2 数据手册
CY28439-2 Clock Generator for Intel Grantsdale Chipset Features • Compliant to Intel CK410 • Supports Intel Prescott and Tejas CPU • Selectable CPU frequencies • Differential CPU clock pairs • 100 MHz differential SRC clocks (two selectable between Fixed and Overclocking) • 96 MHz differential dot clock • 48 MHz USB clocks • 33 MHz PCI clock • Dial-A-Frequency • Watchdog • Two independent overclocking PLLs • Low-voltage frequency select input • I2C support with readback capabilities • Ideal Lexmark Spread Spectrum profile for maximum electromagnetic interference (EMI) reduction • 3.3V power supply • 56-pin SSOP and TSSOP packages CPU SRC x2 x6 PCI x9 REF DOT96 x2 x1 USB x1 24-48M x1 Block Diagram Xin Xout Pin Configuration VDD_RE F RE F 14.318MHz Crystal PLL Reference IREF VDD_CPU CPUT CPUC PLL1 CPU FS_[E:A] Divider VDD_SRC SRCT (PCI Ex) SRCC (PCI Ex) PLL2 SRC Divider VDD_SRC PLL3 SATA Divider SRCT4_SATA SRCC4_SATA VDD_48Mhz PLL4 Fixed Divider DOT96T DOT96C VDD_48 USB48 VDD_48 24/48 VDD_PCI PCI VDD_PCI PCIF VTTPWR_GD#/PD VSS_PCI PCI3 *FS_E/PCI4 PCI5 VSS_PCI VDD_PCI PCIF0 **FS_A/PCIF1 *FS_B/PCIF2 VDD_48 **SEL24_48#/24_48M USB48 VSS_48 DOT96T DOT96C VTTPWRGD#/PD SRCT0 SRCC0 VDD_SRC VSS_SRC SRCT1 SRCC1 SRCT2 SRCC2 VSS_SRC SRCT_SATAT SRCC_SATAC VDD_SRC 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 VDD_PCI PCI2 PCI1 PCI0 SRESET# REF1/FS_D** REF0/FS_C** VSS_REF XIN XOUT VDD_REF SCLK SDATA CPUT0 CPUC0 VDD_CPU CPUT1 CPUC1 VSS_CPU IREF VSSA VDDA VDD_SRC SRCT4 SRCC4 SRCT3 SRCC3 VSS_SRC * Indicates internal pull-up ** Indicates internal pull-down CY28439-2 SDATA SCLK I2C Logic Watchdog Timer SRESET# Rev 1.0, November 21, 2006 2200 Laurelwood Road, Santa Clara, CA 95054 Tel:(408) 855-0555 Fax:(408) 855-0550 Page 1 of 21 www.SpectraLinear.com CY28439-2 Pin Description Pin No. 6,56 1,5 3 Name VDD_PCI VSS_PCI FS_E/PCI4 Type PWR GND 3.3V power supply for outputs. Ground for outputs. Description I,O, 3.3V-tolerant input for CPU frequency selection/33-MHz clock. PU,SE Refer to DC Electrical Specifications table for Vil_FS and Vih_FS specifications. O, SE 33 MHz clocks. O,SE 33 MHz free-running clock I/O,PD, 3.3V-tolerant input for CPU frequency selection/Free-running 33-MHz clock. SE Refer to DC Electrical Specifications table for Vil_FS and Vih_FS specifications. I/O, PU, 3.3V-tolerant input for CPU frequency selection/Free-running 33-MHz clock. SE Refer to DC Electrical Specifications table for Vil_FS and Vih_FS specifications. I, PD 3.3V LVTTL input. This pin is a level sensitive strobe used to latch the FS_A, FS_B, FS_C,FS_D, FS_E, SEL24_48. After VTT_PWRGD# (active LOW) assertion, this pin becomes a real-time input for asserting power-down (active HIGH). 3.3V power supply for outputs. 2,4,53,54, PCI 55 7 8 9 16 PCIF0 FS_A/PCIF1 FS_B/PCIF2 VTT_PWRGD#/PD 10 11 12 13 14,15 17,18,21, 22,23,24, 30,31,32, 33 19,28,34 26,27 20,25,29 35 36 37 41 38 45 44 46 47 48 49 50 VDD_48 PWR SEL24_48#/24_48 I/O, PD, Latched select input for 24-/48-MHz output/ 24-/48-MHz output M SE 0 = 48 MHz, 1 = 24 MHz USB48 VSS_48 DOT96T, DOT96C SRCT/C I/O, GND 48 MHz clock output. Ground for outputs. O, DIF Fixed 96 MHz clock output. O, DIF Differential serial reference clocks. Outputs have overclocking capability. VDD_SRC SRCT/C_SATAT/C VSS_SRC VDDA VSSA IREF VDD_CPU VSS_CPU SCLK SDATA VDD_REF XOUT XIN VSS_REF REF0/FS_C PWR GND PWR GND I PWR GND I I/O PWR I GND 3.3V power supply for outputs. Ground for outputs. 3.3V power supply for PLL. Ground for PLL. A precision resistor is attached to this pin, which is connected to the internal current reference. 3.3V power supply for outputs. Ground for outputs. SMBus-compatible SCLOCK. SMBus-compatible SDATA. 3.3V power supply for outputs. 14.318 MHz crystal input. Ground for outputs. O, DIF Differential serial reference clock. Recommended output for SATA. 39,40,42,43 CPUT/C O, DIF Differential CPU clock outputs. O, SE 14.318 MHz crystal output. I/O, SE, 3.3V-tolerant input for CPU frequency selection/Reference clock. PD Selects test mode if pulled to VIHFS_C when VTT_PWRGD# is asserted LOW. Refer to DC Electrical Specifications table for VILFS_C,VIMFS_C,VIHFS_C specifications. O, SE, 3.3V-tolerant input for CPU frequency selection/Reference clock. PD Refer to DC Electrical Specifications table for Vil_FS and Vih_FS specifications. O, SE 3.3V output for Watchdog reset. This output is open drain type with a high (>100-k ) internal pull-up resistor. 51 52 REF1/FS_D SRESET# Rev 1.0, November 21, 2006 Page 2 of 21 CY28439-2 Frequency Select Pins (FS_[A:E]) Host clock frequency selection is achieved by applying the appropriate logic levels to FS_A, FS_B, FS_C, FS_D, and FS_E inputs prior to VTT_PWRGD# assertion (as seen by the clock synthesizer). Upon VTT_PWRGD# being sampled LOW by the clock chip (indicating processor VTT voltage is stable), the clock chip samples the FS_A, FS_B, FS_C, FS_D, and FS_E input values. For all logic levels of FS_A, FS_B, FS_C, FS_D, and FS_E, VTT_PWRGD# employs a one-shot functionality in that once a valid LOW on VTT_PWRGD# has been sampled, all further VTT_PWRGD#, FS_A, FS_B, FS_C, FS_D, and FS_E transitions will be ignored, except in test mode. FS_C is a three level input, when sampled at a voltage greater than 2.1V by VTTPWRGD#, the device will enter test mode as selected by the voltage level on the FS_B input. The registers associated with the Serial Data Interface initialize to their default setting upon power-up, and therefore use of this interface is optional. Clock device register changes are normally made upon system initialization, if any are required. The interface cannot be used during system operation for power management functions. Data Protocol The clock driver serial protocol accepts byte write, byte read, block write, and block read operations from the controller. For block write/read operation, the bytes must be accessed in sequential order from lowest to highest byte (most significant bit first) with the ability to stop after any complete byte has been transferred. For byte write and byte read operations, the system controller can access individually indexed bytes. The offset of the indexed byte is encoded in the command code, as described in Table 1. The block write and block read protocol is outlined in Table 2 while Table 3 outlines the corresponding byte write and byte read protocol. The slave receiver address is 11010010 (D2h). Serial Data Interface To enhance the flexibility and function of the clock synthesizer, a two-signal serial interface is provided. Through the Serial Data Interface, various device functions, such as individual clock output buffers, can be individually enabled or disabled. Input Conditions FS_D FS_C FS_B FS_A Output Frequency CPU SRC SRC M CPU PLL CPU M CPU N CPU N SRC PLL SRC N SRC N divider (not DEFAULT allowable Gear divider DEFA ULT allowable Gear Constants range for Constants changeable range for by user) DAF DAF (G) FSEL_3 FSEL_2 FSEL_1 FSEL_0 (MHz) (MHz) 0 0 0 0 0 0 0 1 1 1 1 1 1 1 X X 1 0 0 0 0 1 1 1 0 0 0 0 1 1 HIGH HIGH 0 0 1 1 0 0 1 0 0 1 1 0 0 1 LOW HIGH 1 1 1 0 0 0 0 1 1 1 0 0 0 0 X X 100 133.3333333 166.6666667 200 266.6666667 333.3333333 400 100.952381 133.968254 167 200.952381 266.6666667 334 400.6451613 Tristate REF/N 100 100 100 100 100 100 100 100 100 100 100 100 100 100 Tristate REF/N 30 40 60 60 80 120 120 30 40 60 60 80 120 120 Tristate REF/N 60 60 63 60 60 63 60 63 63 60 63 60 60 62 Tristate REF/N 200 200 175 200 200 175 200 212 211 167 211 200 167 207 Tristate REF/N 200 - 250 200 - 250 175 - 262 200 - 250 200 - 250 175 - 262 200 - 250 212 - 262 211 - 262 167 - 250 211 - 262 200 - 250 167 - 250 207 - 258 Tristate REF/N 30 30 30 30 30 30 30 30 30 30 30 30 30 30 60 60 60 60 60 60 60 60 60 60 60 60 60 60 200 200 - 266 200 200 - 266 200 200 - 266 200 200 - 266 200 200 - 266 200 200 - 266 200 200 - 266 200 200 - 266 200 200 - 266 200 200 - 266 200 200 - 266 200 200 - 266 200 167 - 266 200 167 - 266 Figure 1. CPU and SRC Frequency Select Tables Rev 1.0, November 21, 2006 Page 3 of 21 CY28439-2 Table 1. Command Code Definition Bit 7 (6:0) Description 0 = Block read or block write operation, 1 = Byte read or byte write operation Byte offset for byte read or byte write operation. For block read or block write operations, these bits should be '0000000' Table 2. Block Read and Block Write Protocol Block Write Protocol Bit 1 8:2 9 10 18:11 19 27:20 28 36:29 37 45:38 46 .... .... .... .... Start Slave address – 7 bits Write Acknowledge from slave Command Code – 8 bits Acknowledge from slave Byte Count – 8 bits (Skip this step if I2C_EN bit set) Acknowledge from slave Data byte 1 – 8 bits Acknowledge from slave Data byte 2 – 8 bits Acknowledge from slave Data Byte /Slave Acknowledges Data Byte N – 8 bits Acknowledge from slave Stop Description Bit 1 8:2 9 10 18:11 19 20 27:21 28 29 37:30 38 46:39 47 55:48 56 .... .... .... .... Table 3. Byte Read and Byte Write Protocol Byte Write Protocol Bit 1 8:2 9 10 18:11 19 27:20 28 29 Start Slave address – 7 bits Write Acknowledge from slave Command Code – 8 bits Acknowledge from slave Data byte – 8 bits Acknowledge from slave Stop Description Bit 1 8:2 9 10 18:11 19 20 27:21 28 29 37:30 38 39 Start Slave address – 7 bits Write Acknowledge from slave Command Code – 8 bits Acknowledge from slave Repeated start Slave address – 7 bits Read Acknowledge from slave Data from slave – 8 bits NOT Acknowledge Stop Byte Read Protocol Description Start Slave address – 7 bits Write Acknowledge from slave Command Code – 8 bits Acknowledge from slave Repeat start Slave address – 7 bits Read = 1 Acknowledge from slave Byte Count from slave – 8 bits Acknowledge Data byte 1 from slave – 8 bits Acknowledge Data byte 2 from slave – 8 bits Acknowledge Data bytes from slave / Acknowledge Data Byte N from slave – 8 bits NOT Acknowledge Stop Block Read Protocol Description Rev 1.0, November 21, 2006 Page 4 of 21 CY28439-2 Control Registers Byte 0: Control Register 0 Bit 7 6 5 4 3 2 1 0 @Pup 1 1 1 1 1 1 1 1 Name RESERVED SRC[T/C]4 SRC[T/C]3 SATA[T/C] SRC[T/C]2 SRC[T/C]1 RESERVED SRC[T/C]0 RESERVED SRC[T/C]4 Output Enable 0 = Disable (Tri-state), 1 = Enable SRC[T/C]3 Output Enable 0 = Disable (Tri-state), 1 = Enable SATA[T/C] Output Enable 0 = Disable (Tri-state), 1 = Enable SRC[T/C]2 Output Enable 0 = Disable (Tri-state), 1 = Enable SRC[T/C]1 Output Enable 0 = Disable (Tri-state), 1 = Enable RESERVED SRC[T/C]0 Output Enable 0 = Disable (Tri-state), 1 = Enable Description Byte 1: Control Register 1 Bit 7 6 5 4 3 2 1 0 @Pup 1 1 1 1 0 1 1 1 Name PCIF0 DOT_96[T/C] 24_48M REF0 RESERVED CPU[T/C]1 CPU[T/C]0 CPU PCIF0 Output Enable 0 = Disabled, 1 = Enabled DOT_96 MHz Output Enable 0 = Disable (Tri-state), 1 = Enabled 24_48 MHz Output Enable 0 = Disabled, 1 = Enabled REF0 Output Enable 0 = Disabled, 1 = Enabled RESERVED CPU[T/C]1 Output Enable 0 = Disable (Tri-state), 1 = Enabled CPU[T/C]0 Output Enable 0 = Disable (Tri-state), 1 = Enabled PLL1 (CPU PLL) Spread Spectrum Enable 0 = Spread off, 1 = Spread on Description Byte 2: Control Register 2 Bit 7 6 5 4 3 2 1 @Pup 1 1 1 1 1 1 1 Name PCI5 PCI4 PCI3 PCI2 PCI1 PCI0 PCIF2 PCI5 Output Enable 0 = Disabled, 1 = Enabled PCI4 Output Enable 0 = Disabled, 1 = Enabled PCI3 Output Enable 0 = Disabled, 1 = Enabled PCI2 Output Enable 0 = Disabled, 1 = Enabled PCI1 Output Enable 0 = Disabled, 1 = Enabled PCI0 Output Enable 0 = Disabled, 1 = Enabled PCIF2 Output Enable 0 = Disabled, 1 = Enabled Description Rev 1.0, November 21, 2006 Page 5 of 21 CY28439-2 Byte 2: Control Register 2 (continued) Bit 0 @Pup 1 Name PCIF1 PCIF1 Output Enable 0 = Disabled, 1 = Enabled Description Byte 3: Control Register 3 Bit 7 6 5 4 3 2 1 0 @Pup 0 0 0 0 0 0 0 0 Name RESERVED SRC4 SRC3 SATA[T/C] SRC2 SRC1 RESERVED SRC0 RESERVED, Set = 0 Allow control of SRC[T/C]4 with assertion of SW PCI_STP# 0 = Free running, 1 = Stopped with PCI_STP# Allow control of SRC[T/C]3 with assertion of SW PCI_STP# 0 = Free running, 1 = Stopped with PCI_STP# Allow control of SATA[T/C] with assertion of SW PCI_STP# 0 = Free running, 1 = Stopped with PCI_STP# Allow control of SRC[T/C]2 with assertion of SW PCI_STP# 0 = Free running, 1 = Stopped with PCI_STP# Allow control of SRC[T/C]1 with assertion of SW PCI_STP# 0 = Free running, 1 = Stopped with PCI_STP# RESERVED Allow control of SRC[T/C]0 with assertion of SW PCI_STP# 0 = Free running, 1 = Stopped with PCI_STP# Description Byte 4: Control Register 4 Bit 7 6 5 4 3 2 1 0 @Pup HW 0 0 0 0 1 1 1 Name FS_E DOT96[T/C] PCIF2 PCIF1 PCIF0 RESERVED RESERVED RESERVED Description FS_E Reflects the value of the FS_E pin sampled on power-up. 0 = FS_E was low during VTT_PWRGD# assertion. DOT_PWRDWN Drive Mode 0 = Driven in PWRDWN, 1 = Tri-state Allow control of SRC[T/C]2 with assertion of SW PCI_STP# 0 = Free running, 1 = Stopped with PCI_STP# Allow control of PCIF1 with assertion of SW PCI_STP# 0 = Free running, 1 = Stopped with PCI_STP# Allow control of PCIF0 with assertion of SW PCI_STP# 0 = Free running, 1 = Stopped with PCI_STP# RESERVED, Set = 1 RESERVED, Set = 1 RESERVED, Set = 1 Byte 5: Control Register 5 Bit 7 @Pup 0 Name SRC[T/C] Description SRC[T/C] Stop Drive Mode 0 = Driven when PCI_STP# asserted,1 = Tri-state when PCI_STP# asserted RESERVED, Set = 0 RESERVED, Set = 0 RESERVED, Set = 0 SRC[T/C] PWRDWN Drive Mode 0 = Driven when PD asserted,1 = Tri-state when PD asserted RESERVED, Set = 0 CPU[T/C]1 PWRDWN Drive Mode 0 = Driven when PD asserted,1 = Tri-state when PD asserted CPU[T/C]0 PWRDWN Drive Mode 0 = Driven when PD asserted,1 = Tri-state when PD asserted Page 6 of 21 6 5 4 3 2 1 0 0 0 0 0 0 0 0 RESERVED RESERVED RESERVED SRC[T/C][4:0] RESERVED CPU[T/C]1 CPU[T/C]0 Rev 1.0, November 21, 2006 CY28439-2 Byte 6: Control Register 6 Bit 7 6 5 4 3 @Pup 0 0 HW 1 1 Name TEST_SEL TEST_MODE FS_D REF REF/N or Tri-state Select 0 = Tri-state, 1 = REF/N Clock Test Clock Mode Entry Control 0 = Normal operation, 1 = REF/N or Tri-state mode FS_D reflects the value of the FS_D pin sampled on power-up. 0 = FS_D was low during VTT_PWRGD# assertion REF Output Drive Strength 0 = High, 1 = Low Description PCI, PCIF and SRC clock SW PCI_STP# Function outputs except those set 0=SW PCI_STP# assert, 1= SW PCI_STP# deassert to free running When this bit is set to 0, all STOPPABLE PCI, PCIF and SRC outputs will be stopped in a synchronous manner with no short pulses. When this bit is set to 1, all STOPPED PCI, PCIF and SRC outputs will resume in a synchronous manner with no short pulses. FS_C FS_B FS_A FS_C Reflects the value of the FS_C pin sampled on power-up 0 = FS_C was low during VTT_PWRGD# assertion FS_B Reflects the value of the FS_B pin sampled on power-up 0 = FS_B was low during VTT_PWRGD# assertion FS_A Reflects the value of the FS_A pin sampled on power-up 0 = FS_A was low during VTT_PWRGD# assertion 2 1 0 HW HW HW Byte 7: Vendor ID Bit 7 6 5 4 3 2 1 0 @Pup 0 0 0 0 1 0 0 0 Name Revision Code Bit 3 Revision Code Bit 2 Revision Code Bit 1 Revision Code Bit 0 Vendor ID Bit 3 Vendor ID Bit 2 Vendor ID Bit 1 Vendor ID Bit 0 Revision Code Bit 3 Revision Code Bit 2 Revision Code Bit 1 Revision Code Bit 0 Vendor ID Bit 3 Vendor ID Bit 2 Vendor ID Bit 1 Vendor ID Bit 0 Description Byte 8: Control Register 8 Bit 7 @Pup 0 Name CPU_SS Description Spread Selection for CPU PLL 0: –0.5% (peak to peak) 1: –1.0% (peak to peak) Spread Selection for CPU PLL 0: Down spread. 1: Center spread SRC Spread Spectrum Enable 0 = Spread off, 1 = Spread on Spread Selection for SRC PLL 0: –0.5% (peak to peak) 1: –1.0% (peak to peak) RESERVED, Set = 0 USB 48-MHz Output Drive Strength 0 = 2x, 1 = 1x 33-MHz Output Drive Strength 0 = 2x, 1 = 1x RESERVED 6 0 CPU_DWN_SS 5 4 0 0 SRC_SS_OFF SRC_SS 3 2 1 0 0 1 1 0 RESERVED USB PCI RESERVED Rev 1.0, November 21, 2006 Page 7 of 21 CY28439-2 Byte 9: Control Register 9 Bit 7 6 5 4 3 2 1 0 @Pup 0 0 0 0 0 0 0 0 FSEL_D FSEL_C FSEL_B FSEL_A SW Frequency selection bits. See Figure 1. Name RESERVED RESERVED Description Byte 10: Control Register 10 Bit 7 @Pup 0 Name Recovery_Frequency Description This bit allows selection of the frequency setting that the clock will be restored to once the system is rebooted 0: Use HW settings 1: Recovery N[8:0] Timer_SEL selects the WD reset function at SRESET pin when WD time out. 0 = Reset and Reload Recovery_Frequency 1 = Only Reset Time_Scale allows selection of WD time scale 0 = 294 ms 1 = 2.34 s WD_Alarm is set to “1” when the Watchdog times out. It is reset to “0” when the system clears the WD_TIMER time stamp. Watchdog timer time stamp selection 000: Reserved (test mode) 001: 1 * Time_Scale 010: 2 * Time_Scale 011: 3 * Time_Scale 100: 4 * Time_Scale 101: 5 * Time_Scale 110: 6 * Time_Scale 111: 7 * Time_Scale Watchdog timer enable, when the bit is asserted, Watchdog timer is triggered and time stamp of WD_Timer is loaded 0 = Disable, 1 = Enable 6 0 Timer_SEL 5 4 3 2 1 1 0 0 0 0 Time_Scale WD_Alarm WD_TIMER2 WD_TIMER1 WD_TIMER0 0 0 WD_EN Byte 11: Control Register 11 Bit 7 6 5 4 3 2 1 0 @Pup 0 0 0 0 0 0 0 0 Name CPU_DAF_N7 CPU_DAF_N6 CPU_DAF_N5 CPU_DAF_N4 CPU_DAF_N3 CPU_DAF_N2 CPU_DAF_N1 CPU_DAF_N0 Description If Prog_CPU_EN is set, the values programmed in CPU_DAF_N[8:0] and CPU_DAF_M[6:0] will be used to determine the CPU output frequency. The setting of FS_Override bit determines the frequency ratio for CPU and other output clocks. When it is cleared, the same frequency ratio stated in the Latched FS[E:A] register will be used. When it is set, the frequency ratio stated in the FSEL[3:0] register will be used. Rev 1.0, November 21, 2006 Page 8 of 21 CY28439-2 Byte 12: Control Register 12 Bit 7 6 5 4 3 2 1 0 @Pup 0 0 0 0 0 0 0 0 Name CPU_DAF_N8 CPU_DAF_M6 CPU_DAF_M5 CPU_DAF_M4 CPU_DAF_M3 CPU_DAF_M2 CPU_DAF_M1 CPU_DAF_M0 Description If Prog_CPU_EN is set, the values programmed is in CPU_FSEL_N[8:0] and CPU_FSEL_M[6:0] will be used to determine the CPU output frequency. The setting of FS_Override bit determines the frequency ratio for CPU and other output clocks. When it is cleared, the same frequency ratio stated in the Latched FS[E:A] register will be used. When it is set, the frequency ratio stated in the FSEL[3:0] register will be used. Byte 13: Control Register 13 Bit 7 6 5 4 3 2 1 0 @Pup 0 0 0 0 0 0 0 0 Name SRC_N7 SRC_N6 SRC_N5 SRC_N4 SRC_N3 SRC_N2 SRC_N1 SRC_N0 SRC Dial-A-Frequency Bit N7 SRC Dial-A-Frequency Bit N6 SRC Dial-A-Frequency Bit N5 SRC Dial-A-Frequency Bit N4 SRC Dial-A-Frequency Bit N3 SRC Dial-A-Frequency Bit N2 SRC Dial-A-Frequency Bit N1 SRC Dial-A-Frequency Bit N0 Description Byte 14: Control Register 14 Bit 7 6 @Pup 0 0 Name SRC_N8 SW_RESET SRC Dial-A-Frequency Bit N8 Software Reset. When set the device will assert a reset signal on SRESET# upon completion of the block/word/byte write that set it. After asserting and deasserting the SRESET# this bit will self clear (set to 0). The SRESET# pin must be enabled by latching SRESET#_EN on VTT_PRWGD# to utilize this feature. FS_Override 0 = Select operating frequency by FS(E:A) input pins 1 = Select operating frequency by FSEL_(4:0) settings Smooth switch select 0: Select CPU_PLL 1: Select SRC_PLL. RESERVED, Set = 0 RESERVED, Set = 0 Free running 33-MHz Output Drive Strength 0 = 2x, 1 = 1x Watchdog Recovery Bit Description 5 0 FS_[E:A] 4 0 SMSW_SEL 3 2 1 0 0 0 1 0 RESERVED RESERVED PCIF Recovery_N8 Byte 15: Control Register 15 Bit 7 6 5 4 3 @Pup 0 0 0 0 0 Name Recovery N7 Recovery N6 Recovery N5 Recovery N4 Recovery N3 Watchdog Recovery Bit Watchdog Recovery Bit Watchdog Recovery Bit Watchdog Recovery Bit Watchdog Recovery Bit Description Rev 1.0, November 21, 2006 Page 9 of 21 CY28439-2 Byte 15: Control Register 15 (continued) Bit 2 1 0 @Pup 0 0 0 Name Recovery N2 Recovery N1 Recovery N0 Watchdog Recovery Bit Watchdog Recovery Bit Watchdog Recovery Bit Description Byte 16: Control Register 16 Bit 7 6 5 @Pup 1 1 0 Name REF1 USB48 SRC_FREQ_SEL REF1 Output Enable 0 = Disable, 1 = Enable USB48 Output Enable 0 = Disable, 1 = Enable SRC Frequency selection 0: SRC frequency is selected via the FS_E pin 1: SRC frequency is initially set to 167 MHz. RESERVED SATA PLL Spread Spectrum Enable 0 = Spread off, 1 = Spread on Programmable SRC frequency enable 0 = disabled, 1 = enabled. Programmable CPU frequency enable 0 = disabled, 1 = enabled. Description 4 3 2 1 0 0 0 0 0 0 RESERVED SRC_SATA Prog_SRC_EN Prog_CPU_EN Watchdog Autorecovery Watchdog Autorecovery Mode 0 = Disable (Manual), 1= Enable (Auto) crystal not parallel. It’s a common misconception that load capacitors are in parallel with the crystal and should be approximately equal to the load capacitance of the crystal. This is not true. The CY28439-2 requires a Parallel Resonance Crystal. Substituting a series resonance crystal will cause the CY28439-2 to operate at the wrong frequency and violate the ppm specification. For most applications there is a 300-ppm frequency shift between series and parallel crystals due to incorrect loading. Crystal Loading Crystal loading plays a critical role in achieving low ppm performance. To realize low ppm performance, the total capacitance the crystal will see must be considered to calculate the appropriate capacitive loading (CL). Figure 2 shows a typical crystal configuration using the two trim capacitors. An important clarification for the following discussion is that the trim capacitors are in series with the Table 4. Crystal Recommendations Frequency (Fund) 14.31818 MHz Cut AT Loading Load Cap Parallel 20 pF Drive (max.) 0.1 mW Shunt Cap (max.) 5 pF Motional (max.) 0.016 pF Tolerance (max.) 35 ppm Stability (max.) 30 ppm Aging (max.) 5 ppm Figure 2. Crystal Capacitive Clarification Rev 1.0, November 21, 2006 Page 10 of 21 CY28439-2 Calculating Load Capacitors In addition to the standard external trim capacitors, trace capacitance and pin capacitance must also be considered to correctly calculate crystal loading. As mentioned previously, the capacitance on each side of the crystal is in series with the crystal. This means the total capacitance on each side of the crystal must be twice the specified crystal load capacitance (CL). While the capacitance on each side of the crystal is in series with the crystal, trim capacitors (Ce1,Ce2) should be calculated to provide equal capacitive loading on both sides. Clock Chip Dial-A-Frequency (CPU and SRC) This feature allows the user to overclock their system by slowly stepping up the CPU or SRC frequency. When the programmable output frequency feature is enabled, the CPU and SRC frequencies are determined by the following equation Fcpu = G * N/M or Fcpu=G2 * N, where G2 = G / M “N” and “M” are the values programmed in Programmable Frequency Select N-Value Register and M-Value Register, respectively. “G” stands for the PLL Gear Constant, which is determined by the programmed value of FS[E:A]. See Figure 1 for the Gear Constant for each Frequency selection. The PCI Express only allows user control of the N register, the M value is fixed and documented in Figure 1. In this mode, the user writes the desired N and M value into the DAF I2C registers. The user cannot change only the M value and must change both the M and the N values at the same time, if they require a change to the M value. The user may change only the N value if required. Associated Register Bits Trace 2.8pF Ci1 Ci2 Pin 3 to 6p Cs1 X1 X2 Cs2 XTAL Ce1 CPU_DAF Enable—This bit enables CPU DAF mode. By default, it is not set. When set, the operating frequency is determined by the values entered into the CPU_DAF_N register. Note: the CPU_DAF_N and M register must contain valid values before CPU_DAF is set. Default = 0, (No DAF). CPU_DAF_N—There will be nine bits (for 512 values) to linearly change the CPU frequency (limited by VCO range). Default = 0, (0000) The allowable values for N are detailed in the frequency select table in Figure 1. CPU DAF M—There will be 7 bits (for 128 values) to linearly change the CPU frequency (limited by VCO range). Default = 0, the allowable values for M are detailed in the frequency select table in Figure 1. SRC_DAF Enable—This bit enables SRC DAF mode. By default, it is not set. When set, the operating frequency is determined by the values entered into the SRC_DAF_N register. Note: the SRC_DAF_N register must contain valid values before SRC_DAF is set. Default = 0, (No DAF). SRC_DAF_N—There are nine bits (for 512 values) to linearly change the CPU frequency (limited by VCO range). Default = 0, (0000) The allowable values for N are detailed in the frequency select table in Figure 1. Recovery—The recovery mechanism during CPU DAF when the system locks up and the Watchdog timer is enabled is determined by the “Watchdog Recovery Mode” and “Watchdog Autorecovery Enable” bits. The possible recovery methods are: (A) Auto, (B) Manual (by Recovery N), (C) HW, and (D) No recovery, just send reset signal. There is no recovery mode for SRC Dial-a-Frequency. Ce2 Trim 33pF Figure 3. Crystal Loading Example Use the following formulas to calculate the trim capacitor values for Ce1 and Ce2. Load Capacitance (each side) Ce = 2 * CL – (Cs + Ci) Total Capacitance (as seen by the crystal) CLe = 1 ( Ce1 + Cs1 + Ci1 + 1 1 Ce2 + Cs2 + Ci2 ) CL ................................................... Crystal load capacitance CLe .........................................Actual loading seen by crystal using standard value trim capacitors Ce .....................................................External trim capacitors Cs ............................................. Stray capacitance (terraced) Ci .......................................................... Internal capacitance (lead frame, bond wires etc.) CL ................................................... Crystal load capacitance CLe .........................................Actual loading seen by crystal using standard value trim capacitors Ce .....................................................External trim capacitors Cs ............................................. Stray capacitance (terraced) Ci .......................................................... Internal capacitance (lead frame, bond wires etc.) Software Frequency Select This mode allows the user to select the CPU output frequencies using the Software Frequency select bits in the SMBUS register. FSEL—There will be four bits (for 16 combinations) to select predetermined CPU frequencies from a table. The table selections are detailed in section Figure 1. Rev 1.0, November 21, 2006 Page 11 of 21 CY28439-2 FS_Override—This bit allows the CPU frequency to be selected from HW or FSEL settings. By default, this bit is not set and the CPU frequency is selected by HW. When this bit is set, the CPU frequency is selected by the FSEL bits. Default = 0. Recovery—The recovery mechanism during FSEL when the system locks up is determined by the “Watchdog Recovery Mode” and “Watchdog Autorecovery Enable” bits. The only possible recovery method is to (?) Hardware Settings. Auto recovery or manual recovery can cause a wrong output frequency because the output divider may have changed with the selected CPU frequency and these recovery methods will not recover the original output divider setting. Watchdog Register Bits The following register bits are associated with the Watchdog timer: Watchdog Enable—This bit (by default) is not set, which disables the Watchdog. When set, the Watchdog is enabled. Also, when there is a transition from LOW to HIGH, the timer reloads. Default = 0, disable Watchdog Timer—There will be three bits (for seven combinations) to select the timer value. Default = 000—the Value '000' is a reserved test mode. Watchdog Alarm—This bit is a flag and when it is set, it indicates that the timer has expired. This bit is not set by default. When the bit is set, the user is allowed to clear. Default = 0. Watchdog Time Scale—This bit selects the multiplier. When this bit is not set, the multiplier will be 250 ms. When set (by default), the multiplier will be 3s. Default = 1. Watchdog Reset Mode—This selects the Watchdog reset mode. When this bit is not set (by default), the Watchdog will send a reset pulse and reload the recovery frequency, which depends on Watchdog Recovery Mode setting. When set, it just sends a reset pulse. Default = 0, Reset & Recover Frequency. Watchdog Recovery Mode—This bit selects the location to recover from. One option is to recover from the HW settings (already stored in SMBUS registers for readback capability) and the second is to recover from a register called “Recovery N”. Default = 0 (Recover from the HW setting). Watchdog Autorecovery Enable—This bit by default is set and the recovered values are automatically written into the “Watchdog Recovery Register” and reloaded by the Watchdog function. When this bit is not set, the user is allowed to write to the “Watchdog Recovery Register”. The value stored in the “Watchdog Recovery Register” will be used for recovery. Default = 1, Autorecovery. Watchdog Recovery Register—This is a nine-bit register to store the Watchdog N recovery value. This value can be written by the Autorecovery or User depending on the state of the “Watchdog Autorecovery Enable bit”. Smooth Switching The device contains one smooth switch circuit which is shared by the CPU PLL and SRC PLL. The smooth switch circuit ensures that when the output frequency changes by overclocking, the transition from the old frequency to the new frequency is a slow, smooth transition containing no glitches. The rate of change of output frequency when using the smooth switch circuit is less than 1 MHz/0.667 s. The frequency overshoot and undershoot will be less than 2%. The Smooth Switch circuit can be assigned to either PLL via register byte 14 bit 4. By default the smooth switch circuit is assigned to the CPU PLL. Either PLL can still be overclocked when it does not have control of the smooth switch circuit but it is not guaranteed to transition to the new frequency without large frequency glitches. It is not recommended to enable overclocking and change the N values of both PLLs in the same SMBUS block write. Watchdog Timer The Watchdog timer is used in the system in conjunction with overclocking. It is used to provide a reset to a system that has hung up due to overclocking the CPU and the Front side bus. The Watchdog is enabled by the user and if the system completes its checkpoints, the system will clear the timer. However, when the timer runs out, there will be a reset pulse generated on the SRESET# pin for 20 ms that is used to reset the system. When the Watchdog is enabled (WD_EN = 1) the Watchdog timer will start counting down from a value of Watchdog_timer * time scale. If the Watchdog timer reaches 0 before the WD_EN bit is cleared then it will assert the SRESET# signal and set the Watchdog Alarm bit to 1. To use the Watchdog the SRESET# pin must be enabled by SRESET_EN pin being sampled low by VTTPWRGD# assertion during system boot-up. At any point if during the Watchdog timer countdown, if the time stamp or Watchdog timer bits are changed the timer will reset and start counting down from the new value. After the Reset pulse, the Watchdog will stay inactive until either: 1. A new time stamp or Watchdog timer value is loaded. 2. The WD_EN bit is cleared and then set again. Watchdog Recovery Modes There are two operating modes that requires Watchdog recovery. The modes are Dial-A-Frequency (DAF) or Frequency Select. There are four different recovery modes: The following diagram lists the operating mode and the recovery mode associated with it. Recover to Hardware M,N, O When this recovery mode is selected, in the event of a Watchdog timeout, the original M, N, and O values that were latched by the HW FSEL pins at Chip boot-up should be reloaded. Autorecovery When this recovery mode is selected, in the event of a Watchdog timeout, the M and N values stored in the Recovery M and N registers should be reloaded. The current values of M and N will be latched into the internal recovery M and N registers by the WD_EN bit being set. Rev 1.0, November 21, 2006 Page 12 of 21 CY28439-2 Manual Recovery When this recovery mode is selected, in the event of a Watchdog timeout, the N value as programmed by the user in the N recovery register, and the M value that is stored in the Recovery M register (not accessible by the user) should be restored. The current M value should be latched into the M recovery register by the WD_EN bit being set. No Recovery If no recovery mode is selected, in the event of a Watchdog time out, the device should just assert the SRESET# and keep the current values of M and N. PD (Power-down)—Assertion When PD is sampled HIGH by two consecutive rising edges of CPUC, all single-ended outputs will be held LOW on their next HIGH-to-LOW transition and differential clocks must held high or tri-stated (depending on the state of the control register drive mode bit) on the next diff clock# HIGH-to-LOW transition within 4 clock periods. When the SMBus PD drive mode bit corresponding to the differential (CPU, SRC, and DOT) clock output of interest is programmed to ‘0’, the clock output is held with “Diff clock” pin driven HIGH at 2 x Iref, and “Diff clock#” tri-state. If the control register PD drive mode bit corresponding to the output of interest is programmed to “1”, then both the “Diff clock” and the “Diff clock#” are tri-state. Note the example below shows CPUT = 133 MHz and PD drive mode = ‘1’ for all differential outputs. This diagram and description is applicable to valid CPU frequencies 100, 133, 166, 200, 266, 333, and 400 MHz. In the event that PD mode is desired as the initial power-on state, PD must be asserted HIGH in less than 10 s after asserting Vtt_PwrGd#. PD Deassertion The power-up latency is less than 1.8 ms. This is the time from the deassertion of the PD pin or the ramping of the power supply until the time that stable clocks are output from the clock chip. All differential outputs stopped in a three-state condition resulting from power down will be driven high in less than 300 s of PD deassertion to a voltage greater than 200 mV. After the clock chip’s internal PLL is powered up and locked, all outputs will be enabled within a few clock cycles of each other. Figure 5 is an example showing the relationship of clocks coming up. Software Reset Software reset is a reset function which is used to send out a pulse from SRESET# pin. It is controlled by the SW_RESET enable register bit. Upon completion of the byte/word/block write in which the SW_RESET bit was set, the device will send a RESET pulse on the SRESET# pin. The duration of the SRESET# pulse should be the same as the duration of the SRESET# pulse after a Watchdog timer time out. After the SRESET# pulse is asserted the SW_RESET bit should be automatically cleared by the device. PD (Power-down) Clarification The VTT_PWRGD# /PD pin is a dual-function pin. During initial power-up, the pin functions as VTT_PWRGD#. Once VTT_PWRGD# has been sampled LOW by the clock chip, the pin assumes PD functionality. The PD pin is an asynchronous active HIGH input used to shut off all clocks cleanly prior to shutting off power to the device. This signal is synchronized internal to the device prior to powering down the clock synthesizer. PD is also an asynchronous input for powering up the system. When PD is asserted HIGH, all clocks need to be driven to a LOW value and held prior to turning off the VCOs and the crystal oscillator. PD CPUT, 133MHz CPUC, 133MHz SRCT 100MHz SRCC 100MHz USB, 48MHz DOT96T DOT96C PCI, 33 MHz REF Figure 4. Power-down Assertion Timing Waveform Rev 1.0, November 21, 2006 Page 13 of 21 CY28439-2 Tstable 0.25 ms VDD_A = 2.0V Sample Inputs straps W ait for
CY28439-2 价格&库存

很抱歉,暂时无法提供与“CY28439-2”相匹配的价格&库存,您可以联系我们找货

免费人工找货