SFS1826

SFS1826 thru SFS1829 Solid State Devices, Inc. 14830 Valley View Blvd * La Mirada, Ca 90638 Phone: (562) 404-7855 * Fax: (562) 404-1773 ssdi@ssdi-power.com * www.ssdi-power.com Designer’s Data Sheet FEATURES: • • • • • • Low-Level Gate Characteristics IGT = 200 µA (Max) @ 25oC Low Holding Current IH = 1 mA (Max) @ 25oC Anode Common to Case Hermetically Sealed TX, TXV, S-Level Screening Available. Consult Factory 1.6 AMPS 200 ─ 400 VOLTS SILICON CONTROLLED RECTIFIER MAXIMUM RATINGS Peak Repetitive Reverse Voltage and DC Blocking Voltage SFS1826 SFS1827 SFS1828 SFS1829 SFS1826 SFS1827 SFS1828 SFS1829 Symbol VDRM VRRM Value 200 250 300 400 300 350 400 500 1.6 1.0 0.7 15 0.1 0.01 0.1 6.0 -65 to +200 -65 to +200 72 Units Volts Non-Repetitive Peak Reverse Blocking Voltage (t < 5.0 ms) RMS On-State Current (All Conduction Angles) Average On-State Current Peak Non-Repetitive Surge Current (One Cycle, 60 Hz, TC = 80oC ) Peak Gate Power Average Gate Power Peak Gate Current Peak Gate Voltage Operating Junction Temperature Range Storage Temperature Range Thermal Resistance, Junction to Case VRSM Volts IT (RMS) TC = 50 o C TA = 25 o C IT (AV) ITSM PGM PG (AV) IGM VGM TJ Tstg RθJC Amps Amps Amps Watts Watts Amps Volts o o o C C C/W SFS1826 thru SFS1829 Solid State Devices, Inc. 14830 Valley View Blvd * La Mirada, Ca 90638 Phone: (562) 404-7855 * Fax: (562) 404-1773 ssdi@ssdi-power.com * www.ssdi-power.com ELECTRICAL CHARACTERISTICS Peak Reverse Blocking Current (Rated VRRM) Peak Forward Blocking Current (Rated VDRM, RGK = 1K Ω) Peak On-State Voltage (IF = 1.6 A Peak) Gate Trigger Current (VD = 6 VDC, RL = 100 Ω , TC = 125oC) (VD = 6 VDC, RL = 100 Ω, TC = -65oC) Gate Trigger Voltage (VD = 6 VDC, RL = 100 Ω , TC = 25oC) (VD = 6 VDC, RL = 100 Ω, TC = -65oC) Holding Current (VD = 6 VDC) (VD = 6 VDC, TC = -65oC) Symbol IRRM IDRM VTM IGT Min –– –– –– –– –– –– –– –– –– Max 1 1 1.3 200 350 0.7 0.9 0.3 2.0 Unit µA µA Volts µA VGT Volts IH mA NOTES: 1/ RGK current is not included in measurement. 2/ Thyristor devices shall not be tested with a constant current source for forward and reverse blocking capability such that the voltage applies exceeds the rated blocking voltage. 3/ Thyristor devices shall not have a positive bias applied to the gate concurrently with a negative potential applied to the anode. 4/ Unless Otherwise Specified, All Electrical Characteristics @ TC = 25oC, RGK = 1K Ω. Available Part Numbers: SFS1826/18; SFS1827/18; SFS1828/18; SFS1829/18 PIN ASSIGNMENT (Standard) Package Cathode Gate Anode Pin 2 Pin 3 Pin 1 TO-18 (/18) *For information on curves, contact the Factory Representative for Engineering Assistance. NOTE: All specifications are subject to change without notification. SCD's for these devices should be reviewed by SSDI prior to release. DATA SHEET #: SCR005A DOC