AD2C111-L

AD2C111-L 1 Form A Solid State Rela y with Current Limiting DESCRIPTION The AD2C111-L is a bi-directional, single-pole, single-throw, normally open multipurpose solid-state relay. It is designed to replace electromechanical relays in general purpose switching applications. The relay consists of IR LED optically coupled to a IC that drives two rugged source-to-source enhancement type DMOS transistors. The 4 pin DIP package offers the combination of reduced package size, with 5kV input to output isolation. This device also includes over-current circuitry that protects the device from high load currents and transient spikes by limiting the amount of current that can pass through its output. FEATURES APPLICATIONS • • • • • • • Small 4 pin DIP package outline - reduces board space Current Limiting - protects device from overcurrents High input-output isolation (5kV) Low input control power consumption (2.5mA TYP) 120mA maximum continuous load current 40 ohms maximum on-resistance Long life/high reliability • • • • • Reed relay replacement Meter reading systems Medical equipment Battery monitoring Multiplexers OPTIONS/SUFFIXES* ABSOLUTE MAXIMUM RATINGS* PARAMETER Storage Temperature Operating Temperature Continuous Forward Current Peak Forward Current 4 Load • • • -V -S -TR VDE 0884 compliance (.04" / 10.16mm lead spacing) Surface mount leadform option (65pcs per tube) Tape & Reel Option (2,000 pcs / reel) UNIT °C °C mA A V mW MIN -40 -40 TYP MAX 150 85 50 1 5 500 NOTE: Suffixes listed above are not included in marking on device for part number identification. SCHEMATIC DIAGRAM 1 + Input Reverse Voltage Output Power Dissipation IC 2 - Input 3 Load *The values indicated are absolute stress ratings. Functional operation of the device is not implied at these or any conditions in excess of those defined in electrical characteristics section of this document. Exposure to Absolute Ratings may cause permanent damage to the device and may adversely affect reliability. APPROVALS • UL / C-UL Approved: File E90096 © 2008 Solid State Optronics • San José, CA www.ssousa.com • +1.408.293.4600 Page 1 of 5 AD2C111-L rev 1.40 (03/31/2008) AD2C111-L 1 Form A Solid State Relay with Current Limiting ELECTRICAL CHARACTERISTICS - 25°C PARAMETER INPUT SPECIFICATIONS LED Forward Voltage LED Reverse Voltage Turn-On Current Turn-Off Current V V mA mA 6 1.2 12 2.5 0.5 5 1.5 If = 10mA Ir = 10uA Io = 120mA UNIT MIN TYP MAX TEST CONDITIONS OUTPUT SPECIFICATIONS Blocking Voltage Continuous Load Current Current Limit On-Resistance Leakage Current Output Capacitance Offset Voltage V mA mA Ω µA pA mV 150 30 0.2 25 400 120 180 40 1 50 0.2 Io = 1uA If = 5mA If = 5mA Io = 120mA Vo = 400V Vo = 25V, f = 1.0MHz If = 5mA COUPLED SPECIFICATIONS Isolation Voltage Turn-On Time Turn-Off Time Coupled Capacitance Contact Transient Ratio V ms ms pF V/ µs 2000 5000 1.25 0.1 3 7000 dV = 50V 3 0.5 T = 1 minute If = 5mA, Io = 120mA If = 0, Io = 120mA © 2008 Solid State Optronics • San José, CA www.ssousa.com • +1.408.293.4600 Page 2 of 5 AD2C111-L rev 1.40 (03/31/2008) AD2C111-L 1 Form A Solid State Relay with Current Limiting PERFORMANCE DATA AD2C111-L Typical Turn-On Time Distribution N = 100, Ambient Temperature = 25°C AD2C111-L Typical Turn-Off Time Distribution N = 100, Ambient Temperature = 25°C 40 Device Count 40 Device Count 0.55 0.6 0.65 0.7 0.75 0.8 0.85 0.9 Turn-On Tim e (m s) 30 20 10 0 30 20 10 0 0.01 0.02 0.02 0.03 0.03 0.04 0.04 0.05 Turn-Off Tim e (m s) AD2C111-L Typical On-Resistance Distribution N = 100, Ambient Temperature = 25°C AD2C111-L Typical Leakage Current Distribution N = 100, Ambient Temperature = 25°C 50 Device Count 40 30 20 10 0 24 25 26 27 28 29 30 31 On-Resistance (ohm s) Device Count 60 50 40 30 20 10 0 0.05 0.1 0.15 0.2 0.25 0.3 0.35 0.4 Leakage Current (uA) AD2C111-L Typical Blocking Voltage Distribution N = 100, Ambient Temperature = 25°C AD2C111-L Maximum Load Current vs. Temperature 40 30 20 10 0 400 420 440 460 480 500 520 Blocking Voltage (V) Load Current (mA) 50 Device Count 150 100 50 0 20 40 60 -4 0 -2 0 80 0 Tem perature (C) © 2008 Solid State Optronics • San José, CA www.ssousa.com • +1.408.293.4600 Page 3 of 5 AD2C111-L rev 1.40 (03/31/2008) AD2C111-L 1 Form A Solid State Relay with Current Limiting MECHANICAL DIMENSIONS 4 PIN DUAL IN-LINE PACKAGE 4 PIN SURFACE MOUNT DEVICE END VIEW END VIEW TOP VIEW TOP VIEW BOTTOM VIEW BOTTOM VIEW © 2008 Solid State Optronics • San José, CA www.ssousa.com • +1.408.293.4600 Page 4 of 5 AD2C111-L rev 1.40 (03/31/2008) AD2C111-L 1 Form A Solid State Relay with Current Limiting DISCLAIMER Solid State Optronics (SSO) makes no warranties or representations with regards to the completeness and accuracy of this document. SSO reserves the right to make changes to product description, specifications at any time without further notice. SSO shall not assume any liability arising out of the application or use of any product or circuit described herein. Neither circuit patent licenses nor indemnity are expressed or implied. Except as specified in SSO's Standard Terms & Conditions, SSO disclaims liability for consequential or other damage, and we make no other warranty, expressed or implied, including merchantability and fitness for particular use. LIFE SUPPORT POLICY SSO does not authorize use of its devices in life support applications wherein failure or malfunction of a device may lead to personal injury or death. Users of SSO devices in life support applications assume all risks of such use and agree to indemnify SSO against any and all damages resulting from such use. Life support devices are defined as devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when used properly in accordance with instructions for use can be reasonably expected to result in significant injury to the user, or (d) a critical component in any component of a life support device or system whose failure can be reasonably expected to cause failure of the life support device or system, or to affect its safety or effectiveness. © 2008 Solid State Optronics • San José, CA www.ssousa.com • +1.408.293.4600 Page 5 of 5 AD2C111-L rev 1.40 (03/31/2008)