SPT601

SPT601 DC Input PhotoSCR DESCRIPTION The SPT601 consists of an AlGaAs LED optically coupled to a photo-sensitive SCR. Optical coupling provides high isolation levels while maintaining low-level DC signal control capability. With high load voltage and low input current, the SPT601 is an ideal solution to drive SCR Triacs and Solid State Relays. FEATURES APPLICATIONS • • • • • • • Low input control current (5mA MAX) High blocking voltage (400V MIN) 400mA maximum continuous current High input-to-output isolation (3.75kV MIN, 5.3kV MAX) High Transient Immunity (dV/dt = 400V/us MIN) RoHS compliant / LeadFree Component Solid state reliability • • • • • • Valve control Solenoids Remote switching Home appliances Metering equipment Heating elements OPTIONS/SUFFIXES* ABSOLUTE MAXIMUM RATINGS* PARAMETER Storage Temperature Operating Temperature Continuous Input Current Transient Input Current Reverse Input Control Voltage Total Package Power Dissipation Surge Current Rating UNIT °C °C mA mA V mW A 6 500 10 MIN -55 -40 TYP MAX 125 85 40 400 • • • -H -S -TR High Input-Output Isolation (5.3kVrms) Surface Mount Leadform Option Tape and Reel Option NOTE: Suffixes listed above are not included in marking on device for part number identification. SCHEMATIC DIAGRAM *The values indicated are absolute stress ratings. Functional operation of the device is not implied at these or any conditions in excess of those defined in electrical characteristics section of this document. Exposure to Absolute Ratings may cause permanent damage to the device and may adversely affect reliability. APPROVALS • UL, C-UL Pending © 2004 Solid State Optronics • San José, CA www.ssousa.com • +1.408.293.4600 Page 1 of 5 SPT601 rev 1.40 (10/25/2004) SPT601 DC Input PhotoSCR ELECTRICAL CHARACTERISTICS - 25°C PARAMETER INPUT SPECIFICATIONS LED Forward Voltage LED Reverse Voltage Must Operate Current Reverse Current Junction Capacitance V V mA µA pF 5 6 1.2 12 2.5 5 10 1.5 If = 10mA Ir = 10uA Io = 400mA, resistive load Vr = 6.0V Vf = 0V UNIT MIN TYP MAX TEST CONDITIONS OUTPUT SPECIFICATIONS Forward Blocking Voltage Reverse Blocking Voltage Continuous Load Current Surge Current Rating Holding Current On-Voltage Leakage Current Gate Trigger Voltage Forward Leakage Current Reverse Leakage Current Gate Trigger Current V V mA A µA V µA V µA µA µA 0.6 1 1 20 1.1 400 400 400 10 500 1.4 10 1 10 10 50 RGK = 10KΩ, TA = 100ºC, Id = 150µA RGK=10KΩ, TA=100ºC, Id=150µA If = 5mA T = 16us RGK = 27KΩ, VFX = 50V Io = 400mA Vo = 400V, Rgk = 47k VFX=100V, RGK=27KΩ, RL=10KΩ RGK=10KΩ, VRX=400V, IF=0, TA=100ºC RGK=10KΩ, VRX=400V, IF=0, TA=100ºC VFX=100V, RRG=27KΩ, RL=10KΩ COUPLED SPECIFICATIONS Isolation Voltage -H Suffix Isolation Resistance Coupled Capacitance V V GΩ pF 3750 5300 100 2 T = 1 minute T = 1 minute © 2004 Solid State Optronics • San José, CA www.ssousa.com • +1.408.293.4600 Page 2 of 5 SPT601 rev 1.40 (10/25/2004) SPT601 DC Input PhotoSCR PERFORMANCE DATA SPT601 Maximum Load Current vs. Temperature SPT601 Typical Blocking Voltage Distribution N = 100, Ambient Temperature = 25°C Load Current (mA) 420 400 380 360 340 320 -40 -20 0 20 40 60 80 Tem perature (C) 60 50 40 30 20 10 0 425 450 475 500 525 550 575 600 Blocking Voltage (V) © 2004 Solid State Optronics • San José, CA www.ssousa.com • +1.408.293.4600 Page 3 of 5 Device Count SPT601 rev 1.40 (10/25/2004) SPT601 DC Input PhotoSCR MECHANICAL DIMENSIONS 6 PIN DUAL IN-LINE PACKAGE 6 PIN SURFACE MOUNT DEVICE END VIEW END VIEW TOP VIEW TOP VIEW BOTTOM VIEW/ BOARD PATTERN BOTTOM VIEW/ BOARD PATTERN © 2004 Solid State Optronics • San José, CA www.ssousa.com • +1.408.293.4600 Page 4 of 5 SPT601 rev 1.40 (10/25/2004) SPT601 DC Input PhotoSCR DISCLAIMER Solid State Optronics (SSO) makes no warranties or representations with regards to the completeness and accuracy of this document. SSO reserves the right to make changes to product description, specifications at any time without further notice. SSO shall not assume any liability arising out of the application or use of any product or circuit described herein. Neither circuit patent licenses nor indemnity are expressed or implied. Except as specified in SSO's Standard Terms & Conditions, SSO disclaims liability for consequential or other damage, and we make no other warranty, expressed or implied, including merchantability and fitness for particular use. LIFE SUPPORT POLICY SSO does not authorize use of its devices in life support applications wherein failure or malfunction of a device may lead to personal injury or death. Users of SSO devices in life support applications assume all risks of such use and agree to indemnify SSO against any and all damages resulting from such use. Life support devices are defined as devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when used properly in accordance with instructions for use can be reasonably expected to result in significant injury to the user, or (d) a critical component in any component of a life support device or system whose failure can be reasonably expected to cause failure of the life support device or system, or to affect its safety or effectiveness. © 2004 Solid State Optronics • San José, CA www.ssousa.com • +1.408.293.4600 Page 5 of 5 SPT601 rev 1.40 (10/25/2004)