DRD1204W-TR

Data sheet Part number : DRD1204W-TR Package Product features Bi-color emitting LED (Red / Yellow Green) Outer dimension: 3.0 x 2.5 x 1.5mm ( L x W x H ) ・Lead-free soldering compatible ・RoHS2 compliant Recommended applications ・Light source for various indicator, switch etc. 2020.11.5 Page : 1 DRD1204W-TR Outline dimensions Unit Weight Tolerance Recommended Soldering Pattern 2020.11.5 ：mm ：0.013g ：±0.2 No. Item Material Qty. ① LED Die AlGaInP 2 ② Electrode Copper (Au Plating) 4 ③ Mold Resin Epoxy Resin 1 ④ PCB Glass fabrics 1 Unit：mm Page : 2 DRD1204W-TR Specifications 【 Product Overview 】 ITEM LED Die 1 LED Die 2 DIE MATERIAL AlGaInP EMITTING COLOR RED YELLOW-GREEN RESIN COLOR 【EMITTING AREA】 WATER CLEAR 【 Absolute Maximum Ratings 】 (Ta=25℃) ITEM MAXIMUM RATINGS SYMBOL UNITS LED Die(1) LED Die(2) Power Dissipation Pd 78 mW Forward Current IF 30 mA Notes1 Repetitive Peak Forward Current "1ms, 1/20duty" IFRM 100 mA Notes1 IF Derate Linearly from "25℃" ΔIF 0.43 mA/℃ IFRM Derate Linearly from "25℃" ΔIFRM 1.33 mA/℃ Reverse Voltage VR 5 V Operating Temperature Topr -40 to +85 ℃ Storage Temperature Tstg -40 to +100 ℃ Soldering　Temperature 　"Reflow Soldering" Tsld 260℃ MAX Notes2 Notes 1. Each value described on a list is rating at the time of the single color lighting. The absolutely maximum rating in the simultaneous lighting, the values should be applied 50% Max. of each values. 2. Please refer to page 9, Soldering Conditions. 2020.11.5 Page : 3 DRD1204W-TR Specifications 【 Electro and Optical Characteristics 】 LED Die(1) ITEM (Ta=25℃) SYMBOL CONDITIONS MIN. TYP. MAX. UNITS Forward Voltage VF IF = 20mA - 2.0 2.4 V Reverse Current IR VR = 5V - - 100 μA Luminous Intensity IV IF = 20mA 100 - 340 mcd Peak Wavelength λp IF = 20mA - 635 - nm Dominant Wavelength λd IF = 20mA 621 626 634 nm Spectral Line Half Width Δλ IF = 20mA - 15 - nm LED Die(2) (Ta=25℃) ITEM SYMBOL CONDITIONS MIN. TYP. MAX. UNITS Forward Voltage VF IF = 20mA - 2.0 2.4 V Reverse Current IR VR = 5V - - 100 μA Luminous Intensity IV IF = 20mA 70 - 240 mcd Peak Wavelength λp IF = 20mA - 575 - nm Dominant Wavelength λd IF = 20mA 566 572 578 nm Spectral Line Half Width Δλ IF = 20mA - 15 - nm Notes Above the table of Luminous Intensity (IV) values and Dominant wavelength (λd) values are the　setup　value of　the selection　machine．【Tolerance : IV…±10%、λd…±2nm】 2020.11.5 Page : 4 Specifications DRD1204W-TR 【 Sorting For Luminous Intensity and Dominant Wavelength 】 LED's shall be sorted out into the following ranks of Luminous Intensity and Dominant Wavelength. Luminous Intensity (Iv) Rank IV (mcd) Rank LED Chip 1(Red) MIN. MAX. LED Chip 2 (Yellow-Green) MIN. MAX. 70 105 105 160 AC 160 240 BA 70 105 105 160 BC 160 240 CA 70 105 105 160 160 240 AA AB BB CB 100 150 150 225 225 340 CC CONDITIONS IF =20mA Ta=25℃ Dominant wavelength (λd) Rank　　LED 2 (Yellow-Green) λd (nm) Rank CONDITIONS MIN. MAX. A 566 570 B 570 574 C 574 578 IF =20mA Ta=25℃ Notes Above the table of Luminous Intensity (IV) values and Dominant wavelength (λd) values are the　setup　value of　the selection　machine．【Tolerance : IV…±10%、λd…±2nm】 2020.11.5 Page : 5 Technical Data DRD1204W-TR Relative Intensity vs. wavelength Condition: Ta = 25℃, IF = 20mA 1.2 Relative Intensity 1.0 0.8 0.6 0.4 0.2 0.0 380 430 480 530 580 630 680 730 780 Wavelength (nm) Spatial Distribution Condition: Ta = 25℃, IF = 20mA 0 -30 100 30 Red Yellow Green -60 -90 100 60 50 0 50 90 0 50 100 Relative Intensity (%) 2020.11.5 Page : 6 Technical Data DRD1204W-TR Forward Current vs. Forward Voltage Forward Voltage vs. Ambient Temp. Condition: Ta = 25℃ Condition : IF = 20mA 100 2.2 Red Forward Voltage : VF (V) Forward Current IF (mA) Red Yellow green 10 2.1 2.0 Yellow green 1.9 1.8 1 1.7 1.7 1.8 1.9 2.0 2.1 -40 2.2 -20 0 20 40 60 80 Forward Voltage VF (V) Ambient Temperature : Ta (℃) Relative Luminous Intensity vs. Forward Current Relative Luminous Intensity vs. Ambient Temp. Condition : Ta=25℃ Condition : IF = 20mA 10.0 1.5 Red 1.0 Yellow green CI Relative Flux Relative Intensity Yellow green 1.0 Red 0.5 0.1 0.0 0 5 10 15 20 Forward Current : IF (mA) 2020.11.5 25 30 -40 -20 0 20 40 60 80 Ambient Temperature Ta (℃) Page : 7 Technical Data DRD1204W-TR Ambient Temp. vs. Dominant Wavelength Condition : Ta = 25℃ Condition : IF = 20mA 585 645 585 645 580 640 580 640 575 635 Yellow green 570 630 565 625 Red 560 620 555 Dominant Wavelength : λd (nm) Dominant Wavelength : λd (nm) Forward Current vs. Dominant Wavelength 10 20 635 Yellow green 570 630 565 625 Red 560 620 555 615 0 575 615 -40 30 -20 0 20 40 60 80 Forward Current : IF (mA) Ambient Temperature : Ta CI(℃) Ambient Temp. vs. Max. Forward Current Duty Cycle vs. Max. Forward Current CI Repetition Frequency：f≧50Hz 120 100 Maximum Forward Current IFMAX (mA) Maximum Forward Current IFMAX (mA) Duty=5% 100 Duty=10% 80 Duty=20% 60 Duty=50% 40 DC 20 0 1 -40 -20 0 20 40 Ambient Temperature Ta (℃) 2020.11.5 10 60 80 100 1 10 100 Duty Ratio : (%) Page : 8 DRD1204W-TR Soldering condition 【Soldering Precaution】 (acc.to EIAJ-4701/300) 1. Heat stress during soldering will influence the reliability of LEDs, however that effect will vary on heating method. Also, if components of varying shape are soldered together, it is recommended to set the soldering pad temperature according to the component most vulnerable to heat (e.g., surface mount LED). 2. LED parts including the resin are not stable immediately after soldering ( when they are not at room temperature), any mechanical stress may cause damage to the product. Please avoid such stress after soldering, especially stacking of the boards which may cause the boards to warp and any other types of friction with hard materials. 3. Recommended temperature profile for the Reflow soldering is listed as the temperature of the resin surface. Temperature distribution varies on heating method, PCB material, other components in the assembly, and mounting density. Typically, when FR-4 PCB is mounted with one LED and heated via far infrared and hot air, the difference in temperature between PCB and LED resin will be around 5 to 10℃. Please do not repeat the heating process in Reflow process more than twice. 【Recommended reflow soldering condition 】 Peak Temperature (Soldering ） 260℃ MAX. +1.5 to +5℃/s -1.5 to -5℃/s 230℃ MAX. 120sec MAX. （ Pre-heating ） 150℃ to 180℃ 40sec MAX. 2020.11.5 Note 1 Temperature Profile for the reflow should be set to the surface temperature of resin which is on the top of LED. This should be the maximum temperature for soldering. Lowering the heating temperature and decreasing heating time is very effective in achieving higher reliability. Note 2 The reflow soldering process should be done up to twice (2 times Max). When second process is performed, interval between first and second process should be as short as possible to prevent absorption of moisture to resin of LED. The second soldering process should not be done until LEDs have returned to room temperature (by nature-cooling) after first soldering process. Page : 9 DRD1204W-TR Soldering condition 4. If soldering manually, Stanley recommends using a soldering iron equipped with temperature control. During the actual soldering process, make sure that the soldering iron never touches the LED itself, and prevent the LED's electrode heating temperature from reaching above the heating temperature of the solder pad. All repairs must be performed only once in the same spot; please avoid reusing components. 5. During soldering process, immediately after iron tip is cleaned please make sure that the soldering iron reaches the appropriate temperature before using. Also, please avoid applying any types of pressure to the soldered components before the solder has cooled down and hardened, as it may deteriorate solder performance and solder quality. 【Recommended manual soldering condition】 Temperature of iron tip 350℃ Max. Soldering duration, time 3sec.Max.,1 time 6. When using adhesive material for temporary fixing, thermosetting resin or Ultraviolet radiation (UV) setting resin with heat is recommended. 《Curing conditions, Temperature:150℃Max./Time:120sec.Max.》 7. Flow soldering (dip soldering) is not recommended for this product. 8. lsopropyl alcohol is recommended for cleaning. Some chemicals, including Freon substitute detergents, might corrode the lens or the casing surface, which might cause discoloration, clouding, cracks and so on. Please review the reference chart below before cleaning. If water is used to clean (including the final cleaning process), please use pure water (not tap water), and completely dry the LED before using. Ultrasonic cleaning is not recommended. Cleaning agents Recommended / Not recommended Isopropyl alcohol Pure water  Recommended  Recommended  Recommended Trichloroethylene x Not recommended Chlorothene x Not recommended Acetone x Not recommended Thinner x Not recommended Ethyl alcohol 2020.11.5 Page : 100 Handling precautions DRD1204W-TR 【Other Precautions】 1. The products are designed to achieve higher performance reliability, however, they can be influenced by usage conditions. 2. Absolute maximum ratings are set to prevent LED products from failing due to excess stress (temperature, current, voltage, etc.). These ratings must never be overrun even for a moment. 3. To achieve the highest performance reliability, it is necessary to take into account, factors such as forward voltage adjusted to the usage temperature condition, derating of the power consumption, and other variable factors. 4. Please insert Straight Protective Resistors into the circuit in order to stabilize LED operation and to prevent the device from igniting due to excess current. 5. Please check the actual performance in the assembly because the Specification Sheets are described for LED device only. 6. Please refrain from looking directly at the light source of LED at high output, as it may harm your vision. 7. The products are designed to operate without failure in recommended usage conditions. However, please take the necessary precautions to prevent fire, injury, and other damages should any malfunction or failure arise. 8. The products are manufactured to be used for ordinary electronic equipment. Please contact our sales staff beforehand when exceptional quality and reliability are required, and the failure or malfunction of the products might directly jeopardize life or health (such as for airplanes, aerospace, transport equipment, medical applications, nuclear reactor control systems and so on). 9. When there is a process of supersonic wave welding etc. after mounting the product, there is a possibility of affecting on the reliability of junction part in package (junction part of die bonding and wire bonding). Please use after affirming beforehand there is no problem. 10. The formal specification sheets shall be valid only by exchange of documents by both parties. 2020.11.5 Page : 111 Handling precautions DRD1204W-TR This products are baked (moisture removal) before packaging, and are shipped in moisture-proof packaging (as shown below) to minimize moisture absorption during transportation. However, in regards to storing the products, the use of dry-box under the following conditions is recommended. Moisture-proof bag as the packaging is made of anti-static material but packaging box is not. 【Recommended Storage Condition / Products Warranty Period 】 Temperature +5～30℃ Humidity Under 70% In the case of the package unopened , 6 months under 【 Recommended Storage Condition 】. Please avoid rapid transition from low temp. condition to high temp. condition and storage in corroding and dusty environment. 【Time elapsed after Package Opening】 The package should not be opened until immediately prior to its use, and please keep the time frame between package opening and soldering which is 【maximum If the device needs to be soldered twice, both soldering must be completed within 72h. 72 h】 If any components should remain after their use, please seal the package and store them under the conditions Described in the 【 Recommended Storage Condition 】. The product must be required to perform baking process (moisture removal) for at least 10h and not exceed for 12h , at 60+/-5 degrees C if following conditions apply. 1. In the case of color of indicators (those are in the package of desiccant) change or lose its blue color. 2. In the case of time is passed for 72h after the package is opened once. Please backing process must be performed after putting out from package. Baking may be performed in the tape-reel form, however if it is performed with the reel stacked over one another, it may case deformation of the reels and taping materials, which may cause problems during production. Please make sure that the product has cooled to normal temperature after performing the baking process. Provided that, baking process shall be 2 times MAX. 2020.11.5 Page : 122 DRD1204W-TR Packaging specifications 【Moisture-proof Packaging Specification】 Fastener for re-storage after opening bag. Customer's opening position. A Product Label Heat Sealing position (after product being put in) Desiccant with indicator for moisture level is enclosed. 1 NO. PART NAME MATERIALS REMARKS ① Moisture-proof bag with Aluminum layer PET+Al+PE with ESD protection Flow chart：Package Opening to Mounting 【Flow Chart-package Opening to Mounting】 Stored under recommended condition Moisture-proof package first time opening Allowable leaving time exceeded (*) Yes No Discoloration of silica gel Yes No Baking LED under recommended condition Product Mounting Unused-product remained Yes Return to moisture-proof package and seal No Allowable leaving time means the maximum allowable leaving time after opening package, which depends on each LED type. The allowable leaving time should be calculated form the first opening of package to the time when soldering process is finished. When judging if the allowable leaving time has exceeded or not, please subtract the soldering time. The allowable leaving time after reopening should be calculated form the first opening of package, or from the time when baking process is finished. Finished Reopen the moisture-proof package 2020.11.5 Page : 133 DRD1204W-TR Packaging specifications 【Packing box】 ( RoHS2 / ELV Compliant ) Box TYPE Outline dimension L × W × H (mm) Capacity of the box Type A 280 × 265 × 45 3 reel Type B 310 × 235 × 265 15 reel Type C 440 × 310 × 265 30 reel The above measure is all the reference value. The box is selected out of the above table by shipping quantity. Type A Material / box ： Cardboard C5BF 2020.11.5 Type B,C Material / box ： Cardboard K5AF Partition ： Cardboard K5BF NO. PART NAME MATERIAL REMARKS ② Packing Box Corrugated Cardbord without ESD protection Page : 144 DRD1204W-TR Packaging specifications (acc.to JIS-X0503(Code-39)) 【Label Specification】 A Product label A. Parts number B. Bar-code for parts number C. Parts code (In-house identification code for each parts number) D. Packed parts quantity E. Bar-Code for packed parts quantity F. Lot number & Rank (Please refer to Lot Number Notational System for details ) G. Bar-Code for Lot number & Rank B Opto device label A. Customer Name B. Parts Type C. Parts Code D. Parts Number E. Packed Parts Quantity F. Carton Number G. Shipping Date H. Bar-Code for In-house identification Number Bar-code font : acc.to Code-39(JIX0503) 2020.11.5 Page : 155 DRD1204W-TR Taping and reel specifications (acc.to JIS-C0806-03） 【Appearance】 Direction to take out Note "-TR" means Cathode Side of LEDs should be placed on the sprocket-hole side. Items Specifications Remarks Cover-tape Cover-tape shall be longer than 200mm without carrier-tape The end of cover-tape shall be held with adhesive tape. Carrier-tape Empty pocket shall be more than 10 pieces. Please refer to the above figure for Taping & reel orientation . Empty pocket shall be more than 15 pieces. The end of taping shall be inserted into a slit of the hub. Leader area Trailer area 2020.11.5 Page : 166 DRD1204W-TR Taping and reel specifications Unit (acc.to JIS-C0806-03） :mm 【Taping Dimensions】 ③ ② (Center hole) 【Reel Dimensions】 2020.11.5 NO. PART NAME REMARKS ① Carrier reel with ESD protection ② Cover tape with ESD protection ③ Carrier tape with ESD protection Page : 177 Taping and reel specifications DRD1204W-TR (acc.to JIS-C0806-03） 【 Qty. per Reel】 2,500 pcs./ reel 【Mechanical strength】 Cover-tape adhesive strength shall be 0.1～1.0N ( An angle between carrier-tape and cover-tape shall be170 deg. ). Both tapes shall be so sealed that the contained parts will not come out from the tape when it is bent at a radius of 15mm. 【 Others】 ・Reversed-orientation, Up-side down placing, side placing and out of spec. parts mix shall not be held. ・The number of empty pockets within a reel is made into 5pcs. or less and no more than 1 connecting empty pockets of taping. 2020.11.5 Page : 188 DRD1204W-TR Lot number notational system ① ② ③ ④ ⑤ ⑥ ⑦ ⑧ ⑨ ① - 1digit ： Production location (mark identify alphabet) ② - 1digit ： Production year (The last digit of production year 2024→4, 2025→5, 2026→6, 2027→7 ･･･) ③ - 2digits ： Production month (Jan. to Sep. , should be 01,02,03 ･･･) ④ - 2digits ： Production date ⑤ - 3digits ： Serial number ⑥ - 2digits ： Tape and reel following number ⑦ - 2digits ： Total power rank. (If total power rank is 1 digit, "-" shall be dashed on the place for the second digit. If there is no identified rank, "- -" is used to indicate.) ⑧ - 2digits ： Wavelength rank (If wavelength rank is 1 digit, "-" shall be dashed on the place for the second digit. If there is no identified rank, "- -" is used to indicate.) ⑨ - 1digit ： VF Rank (If rank is not defined, "-" is described.) 2020.11.5 Page : 199 DRD1204W-TR Compliance with RoHS2/ELV This product is in compliance with RoHS2 / ELV. Prohibition substance and it's criteria value of RoHS2 / ELV are as follows. ・RoHS2 instruction 　…　Refer to following 1 to 10. ・ELV instruction 　…　Refer to following 1 to 4. No. 2020.11.5 Substances Threshold 1 Lead and its compounds 0.1% (1,000ppm) 2 Mercury and its compounds 0.1% (1,000ppm) 3 Cadmium and its compounds 0.01% (100ppm) 4 Hexavalent chromium compounds 0.1% (1,000ppm) 5 PBB : Polybrominated Biphenyls 0.1% (1,000ppm) 6 PBDE : Polybrominated Biphenyl Ethers 0.1% (1,000ppm) 7 DEHP : Bis (2-ethylhexyl) phthalate 0.1% (1,000ppm) 8 BBP : Butyl benzyl phthalate 0.1% (1,000ppm) 9 DBP : Dibutyl phthalate 0.1% (1,000ppm) 10 DIBP : Diisobutyl phthalate 0.1% (1,000ppm) Page : 20 DRD1204W-TR Reliability testing result 1. Reliability testing result Test Item Standard Test Condition Duration Failure Operating Life EIAJ ED-4701 /100(101) Ta = 25℃, IF = 30mA 1,000h 0 / 25 High Temperature Storage Life EIAJ ED-4701 /200(201) Ta = 100℃ 1,000h 0 / 25 Low Temperature Storage Life EIAJ ED-4701 /200(202) Ta = -40℃ 1,000h 0 / 25 Wet High Temperature Storage Life EIAJ ED-4701 /100(101) Ta=60℃±2℃, Rh=90%±5% 1,000h 0 / 25 Thermal Shock EIAJ ED-4701 /100(105) Ta= 100℃ to -40℃ (each 15min) 5 cycles 0 / 25 Resistance to Reflow Soldering EIAJ ED-4701 /300(301) Preheating ： 150 to 180℃　120s Max. Soldering ： 230℃ 40s Max. Peak Temperature ： 260℃ 2times 0 / 25 Vibration, Variable Frequency EIAJ ED-4701 /400(403) 98.1m/s2(10G) 100～2,000Hz 20min Sweep XYZ direction 2h of each direction 0 / 10 2. Failure criteria Item Symbol Condition Failure Criteria Luminous Intensity IV 20mA Testing Min. Value ＜ Standard Min. Value × 0.5 Forward Voltage VF 20mA Testing Max. Value ≧ Standard Max. Value × 1.2 Reverse Current IR VR=5V Testing Max. Value ≧ Standard Max. Value × 2.5 Cosmetic appearance - - Notable, decollation, deformation and cracking 2020.11.5 Page : 221 DRD1204W-TR Special Notice to Customers Using the Products and Technical Information Shown in This Data Sheet 1) The technical information shown in the data sheets are limited to the typical characteristics and circuit examples of the referenced products. It does not constitute the warranting of industrial property nor the granting of any license. 2) For the purpose of product improvement, the specifications, characteristics and technical data described in the data sheets are subject to change without prior notice. Therefore it is recommended that the most updated specifications be used in your design. 3) When using the products described in the data sheets, please adhere to the maximum ratings for operating voltage, heat dissipation characteristics, and other precautions for use. We are not responsible for any damage which may occur if these specifications are exceeded. 4) The products that have been described to this catalog are manufactured so that they will be used for the electrical instrument of the benchmark (OA equipment, telecommunications equipment, AV machine, home appliance and measuring instrument). The application of aircrafts, space borne application, transportation equipment, medical equipment and nuclear power control equipment, etc. needs a high reliability and safety, and the breakdown and the wrong operation might influence the life or the human body. Please consult us beforehand if you plan to use our product for the usages of aircrafts, space borne application, transportation equipment, medical equipment and nuclear power control equipment, etc. except OA equipment, telecommunications equipment, AV machine, home appliance and measuring instrument. 5) In order to export the products or technologies described in this data sheet which are under the “Foreign Exchange and Foreign Trade Control Law,” it is necessary to first obtain an export permit from the Japanese government. 6) No part of this data sheet may be reprinted or reproduced without prior written permission from Stanley Electric Co., Ltd. 7) The most updated edition of this data sheet can be obtained from the address below: http://www.stanley-components.com/en/ 2020.11.5 Page : 22