FRYPY1211C-0005-TR

Standard product reference sheet FRYPY1211C-0005-TR 2011/65/EU, (EU)2015/863 10 Substances regulation compliant Lead-free solder heat resistant product Features Package Bi-color emitting product, Milky white resin, Emitting color : Yellow green / Red Outline dimensions : 1.6 x 1.5 x 0.7mm ( L x W x H ) Product features ･Wide temperature range usage is available ・Lead-free soldering compatible ・RoHS:2011/65/EU, (EU)2015/863 compliant ・5mA drive Recommended applications ・Communication machine, electric household appliances, OA/FA, other general applications 2022.11.18 Page : 1 Outline dimensions FRYPY1211C-0005-TR ：mm ：3.0mg ：±0.1 Unit Weight Tolerance ⑤ Inside circuit Red Cathode mark ③ ① Yellow green ④ Polarity mark ② ⑤ No. Part name Material Qty. ① LED die (Red) LED die AlGaInP 1 AlGaInP 1 ② (Yellow green) ③ Mold resin Epoxy resin 1 ④ PCB Glass fabrics 1 ⑤ Electrode Au/Ni/Cu Anode:2 Cathode:2 Note : The cutting burr size of the substrate and pin isn't contained in the size of the height of the product. Recommended soldering pattern Unit：mm PCB bending direction 2022.7.7 Page : 2 Specifications FRYPY1211C-0005-TR 【 Product overview 】 Die material AlGaInP Emitting color Yellow green / Red Resin color (Emitting area) Milky white 【 Absolute maximum ratings 】 (Ta=25℃) MAXIMUM RATINGS ITEM SYMBOL UNITS FR (Red) YPY (Yellow green) Power dissipation Pd 36 36 mW Forward current IF 15 15 mA Repetitive peak forward current "1ms,1/20duty" IFRM 48 48 mA IF Derate linearly from "Ta=25℃" ΔIF 0.21 0.21 mA/℃ IFRM Derate linearly from "Ta=25℃" ΔIFRM 0.69 0.69 mA/℃ Reverse voltage VR 5 5 V Operating temperature Topr -40 to +85 ℃ Storage temperature Tstg -40 to +85 ℃ Soldering　temperature 　"Reflow soldering" Tsld 260 ℃ Notes1 ※ Notes1 Please refer to the attached sheets page 9, Soldering conditions. The ratings specified above are under the condition that only one diode is lit. 50% Max. of each rating shall be applied when two diodes are lit simultaneously. 2022.7.7 Page : 3 Specifications FRYPY1211C-0005-TR 【Electro-Optical characteristics 】 (Ta=25℃) CHARACTERISTICS ITEM SYMBOL Forward voltage CONDITIONS VF UNIT FR YPY Typ. 1.85 1.95 Max. 2.4 2.4 V IF=5mA Reverse current IR VR=5V Max. 100 100 μA Peak wavelength λp IF=5mA Typ. 635 572 nm Dominant wavelength λd IF=5mA Typ. 626 570 nm Spectral line half width △λ IF=5mA Typ. 15 15 nm Typ. (θx) 115 115 Typ. (θy) 140 140 2θ1/2 Half intensity angle IF=5mA deg. Above the table of luminous intensity (I V) values and dominant wavelength (λd) values are the　setup　value of　the selection　machine．【Tolerance : IV…±10%, λd…±1nm】 Note 【 Sorting for Luminous intensity and Dominant wavelength 】 LEDs shall be sorted out into the following ranks of Luminous intensity and Dominant wavelength. Dominant wavelength (λd) rank Luminous intensity (Iv) rank λd (nm) IV (mcd) FR Rank CONDITIONS Min. Max. Min. Max. AA 14.0 22.0 6.3 10.0 AB 14.0 22.0 10.0 16.0 AC 14.0 22.0 16.0 25.0 BA 22.0 36.0 6.3 10.0 BB 22.0 36.0 10.0 16.0 BC 22.0 36.0 16.0 25.0 CA 36.0 57.0 6.3 10.0 CB 36.0 57.0 10.0 16.0 CC 36.0 57.0 16.0 25.0 Note 2022.7.7 YPY YPY Rank CONDITIONS MIN. MAX. A 566.5 570.0 IF=5mA B 570.0 574.5 Ta=25℃ IF=5mA Ta=25℃ Above the table of luminous intensity (Iv) values and dominant wavelength (λd) values are the　setup　value of　the selection　machine．【Tolerance : Iv…±10%, λd…±1nm】 Page : 4 Technical data FRYPY1211C-0005-TR Relative Intensity vs. wavelength Condition: Ta = 25℃, IF =5mA 1.2 1.2 1 1.0 FR YPY Relative intensity 0.8 0.8 0.6 0.6 0.4 0.4 0.2 0.2 0 0 500 520 500 520 540 540 560 580 560 580 600 600 620 620 640 660 640 660 680 680 700 700 Wavelength (nm) Spatial Distribution Condition: Ta = 25℃, IF=5mA YPY x FR y 0° 0° 30° -30° 60° -60° -90° 100 0 Relative intensity : % 2020.4.20 -60° 90° 50 50 x direction 30° -30° 100 y direction 60° -90° 100 90° 50 0 50 100 Relative intensity : % Page : 5 Technical data FRYPY1211C-0005-TR Forward current vs. Forward voltage Relative intensity vs. Forward current Condition: Ta = 25℃ Condition : Ta = 25℃ 3.5 100 3.0 Relative intensity Forward current IF (mA) YPY FR 10 YPY 2.5 FR 2.0 1.5 1 1.0 0.5 0.1 0.0 1.6 1.7 1.8 1.9 2.0 2.1 0 5 10 20 Forward voltage VF (V) Forward current : IF (mA) Forward voltage vs. Ambient temp. Forward voltage vs. Ambient temp. Condition : Ta = 25℃ Condition : Ta = 25℃ 2.2 2.3 FR YPY 2.2 2.1 2.1 IF=15mA 2 Relative intensity Forward voltage : VF (V) 15 IF=10mA IF=5mA 1.9 1.8 2 IF=15mA IF=10mA 1.9 IF=5mA 1.8 1.7 IF=2mA IF=2mA 1.7 -40 -20 0 20 40 60 Ambient temperature : Ta (℃) 2020.4.20 80 100 1.6 -40 -20 0 20 40 60 80 100 Ambient temperature Ta (℃) Page : 6 Technical data FRYPY1211C-0005-TR Power dissipation vs. Ambient temperature Relative intensity vs. Ambient temp. Condition : IF = 5mA 40 10 FR 1 30 Power Dissipation : Pd (mW) Relative intensity 35 YPY 25 20 15 10 5 0.1 -40 0 -20 0 20 40 60 80 100 -40 -20 0 20 40 60 80 100 Ambient temperature : Ta (℃) Ambient temperature : Ta (℃) Ambient temp. vs. Max. forward current Pulse width vs. Maximum tolerable peak current Condition: Ta = 25℃ Conditions : Repetition frequency f≧50Hz, 50 Duty=5% 40 Duty=10% 30 Duty=20% Duty=50% 20 DC 10 0 -40 Maximum forward current : IFMAX (mA) Maximum forward current : IFMAX (mA) 60 -20 0 20 40 60 Ambient temperature : Ta (℃) 2020.4.20 80 100 Pulse width : tw (μs) Page : 7 Technical data FRYPY1211C-0005-TR Duty cycle vs. Maximum forward current Condition : Ta = 25℃ Maximum forward current :IF MAX. (mA) 1000 100 10 1 1 10 100 Duty : % 2020.4.20 Page : 8 Soldering condition FRYPY1211C-0005-TR 【Soldering precaution】 (acc.to EIAJ-4701/300) 1. Heat stress during soldering will influence the reliability of LEDs, however that effect will vary on heating method. Also, if components of varying shape are soldered together, it is recommended to set the soldering pad temperature according to the component most vulnerable to heat (e.g., surface mount LED). 2. LED parts including the resin are not stable immediately after soldering ( when they are not at room temperature), any mechanical stress may cause damage to the product. Please avoid such stress after soldering, especially stacking of the boards which may cause the boards to warp and any other types of friction with hard materials. 3. Recommended temperature profile for the Reflow soldering is listed as the temperature of the resin surface. Temperature distribution varies on heating method, PCB material, other components in the assembly, and mounting density . Please do not repeat the heating process in Reflow process more than 2times. 【Recommended reflow soldering condition 】 Peak temperature 260℃ MAX. (Soldering ） +1.5 to +5℃/s -1.5 to 5℃/s 230℃ MAX. 90 to 120sec （ Pre-heating ） 150℃ to 180℃ 40sec MAX. Notes 1 Temperature Profile for the reflow should be set to the surface temperature of resin which is on the top of LED. This should be the maximum temperature for soldering. Lowering the heating temperature and decreasing heating time is very effective in achieving higher reliability. Notes 2 The reflow soldering process should be done up to twice(2 times Max). When second process is performed, interval between first and second process should be as short as possible to prevent absorption of moisture to resin of LED. The second soldering process should not be done until LEDs have returned to room temperature (by nature-cooling) after first soldering process. 2020.4.20 Page : 9 Soldering condition FRYPY1211C-0005-TR 4. If soldering manually, Stanley recommends using a soldering iron equipped with temperature control. During the actual soldering process, make sure that the soldering iron never touches the device itself, and avoid the device's electrode temperature reaching above the temperature of the solder pad. All repairs must be performed only once in the same place, and please avoid reusing components. 5. During the soldering process with a soldering iron, if the iron, tip has been cleaned, please make sure that the soldering iron reaches the appropriate temperature before resuming the solder process. Also, please avoid applying any types of pressure to the soldered components while the solder is cooling and hardening, as it may influence solder performance and solder quality. 【Recommended manual soldering condition】 Temperature of iron tip 350℃ MAX. Soldering duration, time 3sec.Max., 1 time 6. When using adhesive material for tentative fixatives, thermosetting resin or Ultraviolet radiation(UV) setting resin with heat shall be recommended.《The curing condition, Temperature:150℃Max./Time:120sec.Max.》 7. When cleaning, isopropyl alcohol shall be recommended. Some chemicals, including Freon substitute detergent could corrode or affect the optical characteristics of the lens or the casing surface. Please review the reference chart below for cleaning. Cleani Cleaning agents Recommended / Not recommended Isopropyl alcohol  Recommended Ethyl alcohol  Recommended Pure water  Recommended Trichloroethylene x Not recommended Chlorothene x Not recommended Acetone x Not recommended Thinner x Not recommended 8. This products should not be recommended flow soldering(dip soldering). 2020.4.20 Page : 10 Handling precaution FRYPY1211C-0005-TR 【Other precautions】 1. The products are designed to achieve higher performance reliability, however, they can be influenced by usage conditions. 2. Absolute maximum ratings are set to prevent LED products from failing due to excess stress (temperature, current, voltage, etc.). These ratings must never be overrun even for a moment. 3. To achieve the highest performance reliability, it is necessary to take into account, factors such as forward voltage adjusted to the usage temperature condition, derating of the power consumption, and other variable factors. 4. Please insert Straight Protective Resistors into the circuit in order to stabilize LED operation and to prevent the device from igniting due to excess current. 5. Please check the actual performance in the assembly because the Specification Sheets are described for LED device only. 6. Please refrain from looking directly at the light source of LED at high output, as it may harm your vision. 7. The products are designed to operate without failure in recommended usage conditions. However, please take the necessary precautions to prevent fire, injury, and other damages should any malfunction or failure arise. 8. The products are manufactured to be used for ordinary electronic equipment. Please contact our sales staff beforehand when exceptional quality and reliability are required, and the failure or malfunction of the products might directly jeopardize life or health (such as for airplanes, aerospace, transport equipment, medical applications, nuclear reactor control systems and so on).. 9. The formal specification sheets shall be valid only by exchange of documents by both parties. 2020.4.20 Page : 11 Packaging specifications FRYPY1211C-0005-TR This products are baked (moisture removal) before packaging, and are shipped in moisture-proof packaging (as shown below) to minimize moisture absorption during transportation. However, in regards to storing the products, the use of dry-box under the following conditions is recommended. Moisture-proof bag as the packaging is made of anti-static material but packaging box is not. 【Recommended storage condition / Products warranty period 】 Temperature +5～30℃ Humidity Under 70% In the case of the package unopened , 6 months under 【 Recommended Storage Condition 】. Please avoid rapid transition from low temp. condition to high temp. condition and storage in corroding and dusty environment. 【Time elapsed after package opening】 The package should not be opened until immediately prior to its use, and please keep the time frame between package opening and soldering which is 【maximum If the device needs to be soldered twice, both soldering must be completed within 72h. 72h.】 If any components should remain after their use, please seal the package and store them under the conditions Described in the 【 Recommended Storage Condition 】. The product must be required to perform baking process (moisture removal) for at least 10h and not exceed for 12h , at 60+/-5 degrees C if following conditions apply. 1. In the case of color of indicators (those are in the package of desiccant) change or lose its blue color. 2. In the case of time is passed for 672h after the package is opened once. Please backing process must be performed after putting out from package. Baking may be performed in the tape-reel form, however if it is performed with the reel stacked over one another, it may case deformation of the reels and taping materials, which may cause problems during production. Please make sure that the product has cooled to normal temperature after performing the baking process. Provided that, baking process shall be 2 times MAX. 2020.4.20 Page : 12 Packaging specifications FRYPY1211C-0005-TR 【Moisture-proof packaging specification】 Fastener for re-storage after opening bag. Customer's opening position. A Product Label Heat Sealing position (after product being put in) Desiccant with indicator for moisture level is enclosed. 1 NO. PART NAME MATERIALS REMARKS ① Moisture-proof bag with Aluminum layer PET+Al+PE with ESD protection Flow chart：Package to Mounting 【Flow chart-package opening Opening to mounting】 Stored under recommended condition Moisture-proof package first time opening Allowable leaving time exceeded (*) Yes No Discoloration of silica gel Yes No Baking LED under recommended condition Product Mounting Unused-product remained Yes Return to moisture-proof package and seal No Allowable leaving time means the maximum allowable leaving time after opening package, which depends on each LED type. The allowable leaving time should be calculated form the first opening of package to the time when soldering process is finished. When judging if the allowable leaving time has exceeded or not, please subtract the soldering time. The allowable leaving time after reopening should be calculated form the first opening of package, or from the time when baking process is finished. Finished Reopen the moisture-proof package 2020.4.20 Page : 13 Packaging specifications FRYPY1211C-0005-TR 【 Packing box 】 (RoHS / ELV compliant) ( RoHS・ELV Compliant ) Box type Outline dimension L × W × H (mm) Capacity of the box Type A 280 × 265 × 45 3 reels Type B 310 × 235 × 265 15 reels Type C 440 × 310 × 265 30 reels Type D 305 × 270 × 65 3 reels Type E 370 × 280 × 270 30 reels Type F 530 × 380 × 270 60 reels The above measurements are reference values. The box is selected out of the above table by shipping quantity. B Opto device label Adhesive tape ② Type A Type B, C Material / box ： Cardboard C5BF Type D Material / box ： Cardboard C5WF 2022.7.7 Material / box ： Cardboard K5AF Partition ： Cardboard K5BF Type E, F Material / box ： Cardboard BC-KA125/3CA125/KA125 No. Part name Material Remarks ② Packing box Corrugated Cardboard without ESD protection Page : 14 Packaging specifications FRYPY1211C-0005-TR (acc.to JIS-X0503(Code-39)) 【Label specification】 A Product label A. Parts number B. Bar-code for parts number C. Parts code (In-house identification code for each parts number) D. Packed parts quantity E. Bar-Code for packed parts quantity F. Lot number & rank (Please refer to Lot number notational system for details ) G. Bar-code for Lot number & rank B Opto device label A. Customer name B. Parts type C. Parts code D. Parts number E. Packed parts quantity F. Carton number G. Shipping date H. Bar-code for in-house identification number Bar-code font : acc.to Code-39(JIS-X0503) 2020.4.20 Page : 15 Lot Number Notational System ① ② ③ ④ ⑤ FRYPY1211C-0005-TR ⑥ ⑦ ⑧ ⑨ ① - 1digit ： Production location (Mark identify by alphabet) ② - 1digit ： Production year(The last digit of production year 2025→5, 2026→6, 2027→7, 2028→8 ･･･) ③ - 2digits ： Production month (Jan. to Sep. , should be 01, 02, 03,･････) ④ - 2digits ： Production date ⑤ - 3digits ： Serial number ⑥ - 2digits ： Tape and reel following number ⑦ - 2digits ： Luminous intensity rank. (If luminous intensity rank is 1 digit, "-" shall be dashed on the place for the second digit. If there is no identified intensity rank, "- -" is used to indicate.) ⑧ - 2digits ： Color / Chromaticity rank (If color / chromaticity rank is 1 digit, "-" shall be dashed on the place for the second digit. If there is no identified intensity rank, "- -" is used to indicate.) ⑨ - 1digit ： Option rank (Stanley normally print "-" to indicate) 2020.4.20 Page : 16 Taping and reel specifications FRYPY1211C-0005-TR (acc.to JIS-C0806-03） 【Appearance】 “A” Sprocket hole Cover tape Trailer Chip parts equipment Detailed Leader “A” Hub Cathode side Direction to take out Note "-TR" means Cathode Side of LEDs should be placed on the sprocket-hole side. Items Specifications Remarks Cover-tape Cover-tape shall be longer than 200mm without carrier-tape The end of cover-tape shall be held with adhesive tape. Carrier-tape Empty pocket shall be more than 10 pieces. Please refer to the above figure for Taping & reel orientation . Empty pocket shall be more than 15 pieces. The end of taping shall be inserted into a slit of the hub. Leader area Trailer area 2020.4.20 Page : 17 Taping and reel specifications FRYPY1211C-0005-TR (acc.to JIS-C0806-03） 【 Qty. per Reel】 4,000 parts/reel ※ Minimum Qty. per reel might be 500 parts when getting less than 4,000 parts. In such case, parts of 500-unit-qty. shall be packed in a reel and the qty. shall be identified on the label. 【Mechanical strength】 Cover-tape adhesive strength shall be 0.1～1.0N ( An angle between carrier-tape and cover-tape shall be170 deg. ). Both tapes shall be so sealed that the contained parts will not come out from the tape when it is bent at a radius of 15mm. 【 Others】 ・Reversed-orientation, Up-side down placing, side placing and out of spec. parts mix shall not be held. ・The number of empty pockets within a reel is made into 5pcs. or less and no more than 1 connecting empty pockets of taping. 2020.11.18 Page : 18 Taping and reel specifications FRYPY1211C-0005-TR Unit (acc.to JIS-C0806-03） :mm 【Taping dimensions】 ① (Center hole) ② (Center hole) ③ 【Reel dimensions】 9±0.3 11.4±1 2020.4.20 No. Part name Remarks ① Carrier tape with ESD protection ② Cover tape with ESD protection ③ Carrier reel with ESD protection Page : 19 Correspondence to RoHS / ELV instruction FRYPY1211C-0005-TR This product is in compliance with RoHS / ELV. Prohibition substance and it's criteria value of RoHS / ELV are as follows. ・RoHS instruction 　…　Refer to following 1 to 10. ・ELV instruction 　…　Refer to following 1 to 4. 2011/65/EU, (EU)2015/863 No. 2022.11.18 Substance group name Maximum permissible concentration value 1 Lead and its compounds 1,000ppm (0.1%) 2 Cadmium and its compounds 100ppm (0.01%) 3 Mercury and its compounds 1,000ppm (0.1%) 4 Hexavalent chromium compounds 1,000ppm (0.1%) 5 PBB : Polybrominated Biphenyls 1,000ppm (0.1%) 6 PBDE : Polybrominated Biphenyl Ethers 1,000ppm (0.1%) 7 DEHP : Bis (2-ethylhexyl) phthalate 1,000ppm (0.1%) 8 BBP : Butyl benzyl phthalate 1,000ppm (0.1%) 9 DBP : Dibutyl phthalate 1,000ppm (0.1%) 10 DIBP : Diisobutyl phthalate 1,000ppm (0.1%) Page : 20 Reliability testing result FRYPY1211C-0005-TR 1. Reliability testing result Reliability testing result Applicable standard Room temp. operating life EIAJ ED4701/100(101) Ta=25℃, IF=M axium rated current 1,000 h 0/25 Resistance to soldering heat EIAJ ED4701/300(301) Pre-heating : 150 to 180℃ 120s max. Operation heating : 230℃ 40s max. Peak temperature : 260℃ 2 times 0/25 Temperature cycling EIAJ ED4701/100(105) M inimum rated storage temperature (30min) to Normal temperature (15min) to M aximum rated storage temperature (30min) to Normal temperature (15min) 5 cycles 0/25 Wet high temp. storage life EIAJ ED4701/100(103) Ta=60±2℃, RH=90±5% 1,000 h 0/25 Ta=M aximum rated storage temperature 1,000 h 0/25 Ta=M inimum rated storage temperature 1,000 h 0/25 2h 0/10 High temp. storage life Low temp. storage life Vibration, variable frequency EIAJ ED4701/200(201) EIAJ ED4701/200(202) EIAJ ED4701/400(403) Testing conditions Duration 98.1m/s2 (10G), 100 to 2KHz sweep for 20min., XYZ each direction Failure 2. Failure criteria Item Symbol Condition Failure Criteria Luminous Intensity IV 5mA Testing Min. Value ＜ Standard Min. Value × 0.5 Forward Voltage VF 5mA Testing Max. Value ≧ Standard Max. Value × 1.2 Reverse Current IR VR=5V Testing Max. Value ≧ Standard Max. Value × 2.5 Cosmetic Appearance - - Notable, decollation, deformation and cracking 2020.4.20 Page : 21 FRYPY1211C-0005-TR Special notice to customers using the products and technical information shown in this data sheet 1) The technical information shown in the data sheets are limited to the typical characteristics and circuit examples of the referenced products. It does not constitute the warranting of industrial property nor the granting of any license. 2) For the purpose of product improvement, the specifications, characteristics and technical data described in the data sheets are subject to change without prior notice. Therefore it is recommended that the most updated specifications be used in your design. 3) When using the products described in the data sheets, please adhere to the maximum ratings for operating voltage, heat dissipation characteristics, and other precautions for use. We are not responsible for any damage which may occur if these specifications are exceeded. 4) The products that have been described to this catalog are manufactured so that they will be used for the electrical instrument of the benchmark (OA equipment, telecommunications equipment, AV machine, home appliance and measuring instrument). The application of aircrafts, space borne application, transportation equipment, medical equipment and nuclear power control equipment, etc. needs a high reliability and safety, and the breakdown and the wrong operation might influence the life or the human body. Please consult us beforehand if you plan to use our product for the usages of aircrafts, space borne application, transportation equipment, medical equipment and nuclear power control equipment, etc. except OA equipment, telecommunications equipment, AV machine, home appliance and measuring instrument. 5) In order to export the products or technologies described in this data sheet which are under the “Foreign Exchange and Foreign Trade Control Law,” it is necessary to first obtain an export permit from the Japanese government. 6) No part of this data sheet may be reprinted or reproduced without prior written permission from Stanley Electric Co., Ltd. 7) The most updated edition of this data sheet can be obtained from the address below: http://www.stanley-components.com/en/ 2020.4.20 Page : 22