CXOX

CXOX OSCILLATOR 1 MHz to 160 MHz ® Ultra-Miniature Surface Mount High Frequency Crystal Oscillator Actual Size Top View Side View DESCRIPTION Statek’s ultra miniature and ultra low profile CXOX oscillator consists of a CMOS/TTL compatible hybrid circuit and a state-of-the-art, miniature, fundamental-mode crystal. DIMENSIONS FEATURES A 4 TOP Designed for surface mount applications CMOS and TTL compatible Low power consumption Full military testing available High shock resistance Optional Output Enable/Disable with Tri-State Low EMI emission Hermetically sealed ceramic package Designed and manufactured in the USA TYPICAL DIM A B inches 0.126 0.099 1 3 C 3 D 4 BOTTOM E B 2 2 1 MAXIMUM inches 0.136 0.107 0.043 0.048 0.041 0.031 mm 3.40 2.70 1.09 1.21 1.10 0.85 mm 3.20 2.50 1.00 1.12 1.00 0.75 APPLICATIONS 0.039 C (SM1) C (SM3/SM5) 0.044 D E 0.040 0.030 Military & Aerospace Long range missiles Projectile electronics Smart munitions Communications Navigation GPS Industrial, Computer & Communications Miniature clock oscillator Handheld instrumentation PDA Transponder/Animal migration Medical Test & diagnostic equipment Handheld devices PIN CONNECTIONS 1. Output Enable/Disable (E) or no connection (N) 2. Ground 3. Output 4. VDD SUGGESTED LAND PATTERN 0.141 (3.6) 0.110 (2.9) 0.031 (0.8) 0.039 (1.05) 0.051 (1.3) 0.039 (1.0) 10168 Rev A S YS inches (mm) TEM C ERT I F I C AT N IO STATEK CORPORATION 512 N. MAIN ST., ORANGE, CA 92868 714-639-7810 FAX: 714-997-1256 www.statek.com 01 Pb IS O 90 SPECIFICATIONS ABSOLUTE MAXIMUM RATINGS Specifications below are examples. Specifications are subject to change without notice. Tighter specifications available. Please contact factory. Frequency Range1 Supply Voltage Calibration Tolerance2 Frequency Stability Over Temperature3 + _ 100 ppm for Military Supply Current (Typical) 24 MHz 32 MHz 50 MHz 130 MHz Output Load (CMOS)4 Start-up Time Rise/Fall Time Duty Cycle 5 Supply Voltage VDD -0.5 V to 7.0 V Storage Temperature -55OC to 125OC Maximum Process Temperature 260OC for 20 seconds 1 MHz to 160 MHz _ 1.8 V to 5.0 V +10% + _ + _ 100 ppm ENABLE/DISABLE OPTIONS (E/N) 50 ppm for Commercial + _ 100 ppm for Industrial 1.8 V 1.5 mA 2.0 mA 3.0 mA 12.0 mA 15 pF 5 ms MAX 6 ns MAX 40% MIN 60% MAX 10 ppm MAX 5,000 g, 0.3 ms, 1/2 sine 20 g, 10-2,000 Hz swept sine 3.3 V 3.0 mA 5.0 mA 6.0 mA 23.0 mA 5.0 V 8.0 mA 10.0 mA 13.0 mA 39.0 mA Statek offers two enable/disable options: E and N. The E-version has a Tri-State output and stops oscillating internally when the output is put into the high Z state. The N-version does not have PIN 1 connected internally and so has no enable/disable capability. The following table describes the Enable/Disable option E. ENABLE/DISABLE OPTION E FUNCTION TABLE Enable (Pin 1 High*) Disable (Pin 1 Low) Output Oscillator Current Frequency Output Oscillates Normal High Z State Stops Very Low Aging, first year Shock, survival6 Vibration, survival7 Operating Temp. Range -10OC to 70OC (Commerical) -40OC to 85OC (Industrial) -55OC to 125OC (Military) * When PIN 1 is allowed to float, it is held high by an internal pull-up resistor. PACKAGING OPTIONS 1. 2. 3. 4. 5. 6. 7. Not all frequencies available at all voltages. Contact factory. Other tolerances available. Does not include calibration tolerances. Other tolerances available. Higher CMOS loads and TTL loads available. Contact factory. 45/55 available upon request in most cases. Higher shock levels available. Contact factory. Per MIL-STD-202G, Method 204D, Condition D. Random vibration testing also available. Note: All parameters are measured at ambient temperature with a 10 MΩ, 15 pF load. CXOX - Tray Pack - 12 mm tape, 7” or 13” reels Per EIA 481 (see Tape and Reel data sheet 10109) HOW TO ORDER CXOX SURFACE MOUNT CRYSTAL OSCILLATORS CXOX 4 Supply Voltage 1 = 1.8 V 2 = 2.5 V 3 = 3.0 V 4 = 3.3 V 5 = 5.0 V S “S” if special or custom design. Blank if Std. N Enable/Disable Option E or N SM3 Terminations Blank = SM1 = Gold Plated (Lead Free) SM3 = Solder Dipped SM5 = Solder Dipped (Lead Free) 40.0M , Frequency K = kHz M = MHz 100 Calibration Tolerance @ 250C (in ppm) / 100 Frequency Stability over Temp.Range (in ppm) / / I Temp. Range: C = -10OC to +70OC I = -40OC to +85OC M = -55OC to +125OC S = Customer Specified OR / / 200 Total Frequency Tolerance (in ppm) / I Temp. Range: C = -10OC to +70OC I = -40OC to +85OC M = -55OC to +125OC S = Customer Specified 10168 Rev A S YS TEM C ERT I F I C AT N IO STATEK CORPORATION 512 N. MAIN ST., ORANGE, CA 92868 714-639-7810 FAX: 714-997-1256 www.statek.com 01 Pb IS O 90