74AC174MTR

74AC174 HEX D-TYPE FLIP FLOP WITH CLEAR ■ ■ ■ ■ ■ ■ ■ ■ ■ HIGH SPEED: fMAX = 250MHz (TYP.) at VCC = 5V LOW POWER DISSIPATION: ICC = 4µA(MAX.) at TA=25°C HIGH NOISE IMMUNITY: VNIH = V NIL = 28 % VCC (MIN.) 50Ω TRANSMISSION LINE DRIVING CAPABILITY SYMMETRICAL OUTPUT IMPEDANCE: |IOH| = IOL = 24mA (MIN) BALANCED PROPAGATION DELAYS: tPLH ≅ tPHL OPERATING VOLTAGE RANGE: VCC (OPR) = 2V to 6V PIN AND FUNCTION COMPATIBLE WITH 74 SERIES 174 IMPROVED LATCH-UP IMMUNITY DESCRIPTION The 74AC174 is an advanced high-speed CMOS HEX D-TYPE FLIP FLOP WITH CLEAR fabricated with sub-micron silicon gate and double-layer metal wiring C2MOS tecnology. DIP SOP TSSOP ORDER CODES PACKAGE TUBE DIP SOP TSSOP 74AC174B 74AC174M T&R 74AC174MTR 74AC174TTR Information signals applied to D inputs are transferred to the Q output on the positive going edge of the clock pulse. When the CLEAR input is held low, the Q outputs are held low independentely of the other inputs. All inputs and outputs are equipped with protection circuits against static discharge, giving them 2KV ESD immunity and transient excess voltage. PIN CONNECTION AND IEC LOGIC SYMBOLS April 2001 1/11 74AC174 INPUT AND OUTPUT EQUIVALENT CIRCUIT PIN DESCRIPTION PIN No SYMBOL NAME AND FUNCTION 1 CLEAR 2, 5, 7, 10, 12, 15 3, 4, 6, 11, 13, 14 9 Q0 to Q5 Asynchronous Master Reset (Active LOW) Flip-Flop Outputs D0 to D5 Data Inputs CLOCK 8 16 GND VCC Clock Input (LOW-to-HIGH, Edge Trigger) Ground (0V) Positive Supply Voltage TRUTH TABLE INPUTS OUTPUT FUNCTION CLEAR D CLOCK Q L X X L H L L H H H H X Qn X : Don’t Care LOGIC DIAGRAM This logic diagram has not to be used to estimate propagation delays 2/11 CLEAR NO CHANGE 74AC174 ABSOLUTE MAXIMUM RATINGS Symbol VCC Parameter Supply Voltage Value Unit -0.5 to +7 V -0.5 to VCC + 0.5 -0.5 to VCC + 0.5 V DC Input Diode Current ± 20 mA IOK DC Output Diode Current ± 20 mA IO DC Output Current ± 50 mA ± 300 mA VI DC Input Voltage VO DC Output Voltage IIK ICC or IGND DC VCC or Ground Current Tstg Storage Temperature TL Lead Temperature (10 sec) V -65 to +150 °C 300 °C Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is not implied. RECOMMENDED OPERATING CONDITIONS Symbol VCC Parameter Supply Voltage Value Unit 2 to 6 V VI Input Voltage 0 to VCC V VO Output Voltage 0 to VCC V Top Operating Temperature -55 to 125 °C 8 ns/V dt/dv Input Rise and Fall Time VCC = 3.0, 4.5 or 5.5V (note 1) 1) VIN from 30% to 70% of V CC 3/11 74AC174 DC SPECIFICATIONS Test Condition Symbol VIH VIL VOH VOL II ICC IOLD IOHD Parameter High Level Input Voltage Low Level Input Voltage High Level Output Voltage Low Level Output Voltage Input Leakage Current Quiescent Supply Current Dynamic Output Current (note 1, 2) TA = 25°C VCC (V) 3.0 4.5 5.5 3.0 4.5 5.5 Value VO = 0.1 V or VCC-0.1V Min. Typ. 2.1 3.15 3.85 1.5 2.25 2.75 1.5 2.25 2.75 VO = 0.1 V or VCC-0.1V Max. -55 to 125°C Min. Min. Max. 2.1 3.15 3.85 0.9 1.35 1.65 0.9 1.35 1.65 V 0.9 1.35 1.65 IO=-50 µA 2.9 2.99 2.9 2.9 4.5 IO=-50 µA 4.4 4.49 4.4 4.4 5.5 IO=-50 µA 5.4 5.49 5.4 5.4 3.0 IO=-12 mA 2.56 2.46 2.4 4.5 IO=-24 mA 3.86 3.76 3.7 5.5 IO=-24 mA 4.86 4.76 4.7 Unit Max. 2.1 3.15 3.85 3.0 V V 3.0 IO=50 µA 0.002 0.1 0.1 0.1 4.5 IO=50 µA 0.001 0.1 0.1 0.1 5.5 IO=50 µA 0.001 0.1 0.1 0.1 3.0 IO=12 mA 0.36 0.44 0.5 4.5 IO=24 mA 0.36 0.44 0.5 5.5 IO=24 mA 0.36 0.44 0.5 5.5 VI = VCC or GND ± 0.1 ±1 ±1 µA 5.5 VI = VCC or GND 4 40 80 µA VOLD = 1.65 V max 75 50 mA VOHD = 3.85 V min -75 -50 mA 5.5 1) Maximum test duration 2ms, one output loaded at time 2) Incident wave switching is guaranteed on transmission lines with impedances as low as 50Ω 4/11 -40 to 85°C V 74AC174 AC ELECTRICAL CHARACTERISTICS (CL = 50 pF, RL = 500 Ω, Input tr = tf = 3ns) Test Condition Symbol Parameter tPLH tPHL Propagation Delay Time CLOCK to Y tPHL Propagation Delay Time CLEAR to Y tWL CLEAR Pulse Width, LOW tW ts th tREM fMAX CLOCK Pulse Width Setup Time D to CLOCK, HIGH or LOW Hold Time D to CLOCK, HIGH or LOW Recovery Time CLEAR to CK Maximum Clock Frequency Value TA = 25°C VCC (V) -40 to 85°C -55 to 125°C Min. Min. Min. Typ. Max. (*) 1.5 8.5 11.0 12.5 14.0 5.0(**) 1.5 6.0 8.0 9.5 10.5 3.3(*) 1.5 9.0 11.5 12.5 13.5 (**) 1.5 7.0 9.0 10.5 11.0 3.3(*) 1.0 5.5 7.0 7.0 5.0(**) 1.0 5.0 5.0 5.0 3.3(*) 1.0 5.5 7.0 7.0 5.0(**) 1.0 5.0 5.0 5.0 3.3(*) 2.5 6.5 7.0 7.0 5.0(**) 2.0 5.0 5.5 5.5 3.3(*) 1.0 3.0 3.0 3.0 (**) 0.5 3.0 3.0 3.0 3.3(*) 0 2.5 2.5 2.5 5.0(**) 0 2.0 2.0 2.0 3.3 5.0 5.0 3.3(*) (**) 5.0 Max. 90 200 70 70 100 250 100 100 Unit Max. ns ns ns ns ns ns ns MHz (*) Voltage range is 3.3V ± 0.3V (**) Voltage range is 5.0V ± 0.5V CAPACITIVE CHARACTERISTICS Test Condition Symbol Parameter TA = 25°C VCC (V) CIN Input Capacitance 5.0 CPD Power Dissipation Capacitance (note1) 5.0 Value Min. fIN = 10MHz Typ. Max. -40 to 85°C -55 to 125°C Min. Min. Max. Unit Max. 4.5 pF 33 pF 1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x f IN + ICC/6 (per circuit) 5/11 74AC174 TEST CIRCUIT CL = 50pF or equivalent (includes jig and probe capacitance) RL = R1 = 500Ω or equivalent RT = ZOUT of pulse generator (typically 50Ω) WAVEFORM 1: PROPAGATION DELAYS, SETUP AND HOLD TIMES (f=1MHz; 50% duty cycle) 6/11 74AC174 WAVEFORM 2: PROPAGATION DELAYS (f=1MHz; 50% duty cycle) WAVEFORM 3: RECOVERY TIME (f=1MHz; 50% duty cycle) 7/11 74AC174 Plastic DIP-16 (0.25) MECHANICAL DATA mm DIM. MIN. a1 0.51 B 0.77 TYP. inch MAX. MIN. TYP. MAX. 0.020 1.65 0.030 0.065 b 0.5 0.020 b1 0.25 0.010 D 20 0.787 E 8.5 0.335 e 2.54 0.100 e3 17.78 0.700 F 7.1 0.280 I 5.1 0.201 L Z 3.3 0.130 1.27 0.050 P001C 8/11 74AC174 SO-16 MECHANICAL DATA mm DIM. MIN. TYP. A a1 inch MAX. MIN. TYP. 1.75 0.1 0.068 0.2 a2 MAX. 0.004 0.007 1.65 0.064 b 0.35 0.46 0.013 0.018 b1 0.19 0.25 0.007 0.010 C 0.5 0.019 c1 45 (typ.) D 9.8 10 0.385 0.393 E 5.8 6.2 0.228 0.244 e 1.27 0.050 e3 8.89 0.350 F 3.8 4.0 0.149 0.157 G 4.6 5.3 0.181 0.208 L 0.5 1.27 0.019 0.050 M S 0.62 0.024 8 (max.) P013H 9/11 74AC174 TSSOP16 MECHANICAL DATA mm DIM. MIN. inch TYP. A MAX. MIN. MAX. 1.1 0.433 A1 0.05 0.10 0.15 0.002 0.004 0.006 A2 0.85 0.9 0.95 0.335 0.354 0.374 b 0.19 0.30 0.0075 0.0118 c 0.09 0.20 0.0035 0.0079 D 4.9 5 5.1 0.193 0.197 0.201 E 6.25 6.4 6.5 0.246 0.252 0.256 E1 4.3 4.4 4.48 0.169 0.173 0.176 e 0.65 BSC 0.0256 BSC K 0o 4o 8o 0o 4o 8o L 0.50 0.60 0.70 0.020 0.024 0.028 A A2 A1 b e K c E1 PIN 1 IDENTIFICATION 1 L E D 10/11 TYP. 74AC174 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. © The ST logo is a registered trademark of STMicroelectronics © 2001 STMicroelectronics - Printed in Italy - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - China - Finland - France - Germany - Hong Kong - India - Italy - Japan - Malaysia - Malta - Morocco Singapore - Spain - Sweden - Switzerland - United Kingdom © http://www.st.com 11/11