74LCX07YMTR

74LCX07 Low-voltage CMOS hex buffer (open drain) with 5 V tolerant inputs Datasheet − production data Features ■ 5 V tolerant inputs ■ High speed – tPD = 5.2 ns (max.) at VCC = 3 V ■ Power-down protection on inputs and outputs ■ Symmetrical output impedance – |IOH| = IOL = 24 mA (min.) at VCC = 3 V ■ PCI bus levels guaranteed at 24 mA ■ Operating voltage range – VCC (opr.) = 2.0 V to 3.6 V ■ Pin and function compatible with 74 series 07 ■ Latch-up performance exceeds 500 mA (JESD 17) ■ ESD performance – HBM: 2000 V (MIL STD 883 method 3015) – MM: 200 V – CDM: 1000 V Applications ■ Automotive ■ Industrial ■ Computer ■ Consumer Table 1. TSSOP14 SO-14 Description The 74LCX07 device is a low-voltage CMOS open drain hex buffer manufactured with submicron silicon gate and double-layer metal wiring C2MOS technology. It is ideal for low-power and high-speed 3.3 V applications and can be interfaced to a 5 V signal environment for inputs. The internal circuit is composed of 2 stages including a buffer output, which provides high noise immunity and stable output. It has the same speed performance at 3.3 V as the 5 V AC/ACT family, combined with lower power consumption. All inputs and outputs are equipped with protection circuits against static discharge, giving them 2 kV ESD immunity and transient excess voltage. Device summary Order code Temperature range Package Packaging Marking 74LCX07TTR -40/+85 °C TSSOP14 Tape and reel LCX07 74LCX07YTTR(1) -40/+85 °C TSSOP14 (automotive grade) Tape and reel LCX07Y 74LCX07MTR -40/+85 °C SO-14 Tape and reel 74LCX07 74LCX07YMTR(1) -40/+85 °C SO-14 (automotive grade) Tape and reel 74LCX07Y 1. Qualification and characterization according to AEC Q100 and Q003 or equivalent, advanced screening according to AEC Q001 and Q002 or equivalent. October 2012 This is information on a product in full production. Doc ID 6818 Rev 8 1/16 www.st.com 16 Contents 74LCX07 Contents 1 Logic symbols and I/O equivalent circuit . . . . . . . . . . . . . . . . . . . . . . . . 3 2 Pin settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3 2.1 Pin connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2.2 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2.3 Truth table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Recommended operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 4 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 5 Test circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 6 Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 7 Package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 8 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 2/16 Doc ID 6818 Rev 8 74LCX07 1 Logic symbols and I/O equivalent circuit Logic symbols and I/O equivalent circuit Figure 1. IEC logic symbols Figure 2. Input and output equivalent circuit Doc ID 6818 Rev 8 3/16 Pin settings 74LCX07 2 Pin settings 2.1 Pin connections Figure 3. 2.2 Pin connections (top through view) Pin description Table 2. 2.3 Pin description Pin number Symbol Name and function 1, 3, 5, 9, 11, 13 1A to 6A Data inputs 2, 4, 6, 8, 10, 12 1Y to 6Y Data outputs 7 GND Ground (0 V) 14 VCC Positive supply voltage Truth table Table 3. Truth table Input Output A Y L L H Z (1) 1. High impedance. 4/16 Doc ID 6818 Rev 8 74LCX07 3 Maximum ratings Maximum ratings Stressing the device above the rating listed in Table 4: Absolute maximum ratings may cause permanent damage to the device. These are stress ratings only and operation of the device at these or any other conditions above those indicated in Table 5: Recommended operating conditions of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Table 4. Absolute maximum ratings Symbol Value Unit Supply voltage -0.5 to +7.0 V VI DC input voltage -0.5 to +7.0 V VO DC output voltage (V CC = 0 V) -0.5 to +7.0 V -0.5 to VCC + 0.5 V -50 mA -50 mA VCC Parameter VO DC output voltage (high or low IIK DC input diode current state)(1) current(2) IOK DC output diode IO DC output current ± 50 mA ICC DC supply current per supply pin ± 100 mA IGND DC ground current per supply pin ± 100 mA Tstg Storage temperature -65 to +150 °C 300 °C Value Unit 2.0 to 3.6 V TL Lead temperature (10 sec.) 1. IO absolute maximum rating must be observed. 2. VO < GND. Recommended operating conditions Table 5. Recommended operating conditions Symbol VCC Parameter Supply voltage(1) VI Input voltage 0 to 5.5 V VO Output voltage (VCC = 0 V) 0 to 5.5 V VO Output voltage (high or low state) 0 to VCC V IOH, IOL High or low level output current (VCC = 3.0 to 3.6 V) ± 24 mA IOH, IOL High or low level output current (VCC = 2.7 V) ± 12 mA 0 to 10 ns/V dt/dv Input rise and fall time(2) 1. Truth table guaranteed: 1.5 V to 3.6 V. 2. VIN from 0.8 V to 2 V at VCC = 3.0 V. Doc ID 6818 Rev 8 5/16 Electrical characteristics 74LCX07 4 Electrical characteristics Table 6. DC specifications Test condition Symbol Parameter VIH High level input voltage VIL Low level input voltage VOL IO = 100 μA 0.2 2.7 IO = 12 mA 0.4 IO = 16 mA 0.4 IO = 24 mA 0.55 2.7 to 3.6 VI = 0 to 5.5 V ±5 μA 0 VI or VO = 5.5 V 10 μA VI = VIH or VIL VO = 0 to VCC ±5 μA VI = VCC or GND 10 VI or VO = 3.6 to 5.5 V ± 10 VIH = VCC - 0.6 V 500 Low level output voltage Input leakage current 2.7 to 3.6 ICC Quiescent supply current 2.7 to 3.6 I incr. per input 2.7 to 3.6 V μA Parameter Dynamic low level quiet output(1) TA = 25 °C VCC (V) 3.3 Value Min. VIL = 0 V VIH = 3.3 V Typ. Doc ID 6818 Rev 8 Unit Max. 0.8 V -0.8 1. Number of outputs defined as “n”. Measured with “n-1” outputs switching from HIGH to LOW or LOW to HIGH. The remaining output is measured in the LOW state. 6/16 μA Dynamic switching characteristics Test condition VOLV V 2.7 to 3.6 High impedance output leakage current VOLP V 0.8 IOZ Symbol Max. 2.0 Power OFF leakage current Table 7. Min. Unit 2.7 to 3.6 Ioff ΔICC -40 to 85 °C VCC (V) 3.0 II Value 74LCX07 Table 8. Electrical characteristics AC electrical characteristics Test condition Symbol Parameter VCC (V) Value CL (pF) RL (Ω) ts = tr (ns) 50 500 2.5 Min. 2.7 tPLZ Propagation delay time tPZL Propagation delay time 3.0 to 3.6 ns 1.0 5.2 7.0 50 500 2.5 3.0 to 3.6 Output to output skew time(1), (2) Max. 7.0 2.7 tOSLH tOSHL Unit -40 to 85 °C 3.0 to 3.6 ns 1.0 50 500 2.5 5.2 1.0 ns 1. Skew is defined as the absolute value of the difference between the actual propagation delay for any two outputs of the same device switching in the same direction, either HIGH or LOW (tOSLH = | tPLHm - tPLHn|, tOSHL = | tPHLm - tPHLn|). 2. Parameter guaranteed by design. Table 9. Capacitive characteristics Test condition Symbol CIN Parameter Value TA = 25 °C VCC (V) Min. Typ. Unit Max. Input capacitance 3.3 VIN = 0 to VCC 6 pF COUT Output capacitance 3.3 VIN = 0 to VCC 14 pF CPD Power dissipation capacitance(1) 3.3 fIN = 10 MHz VIN = 0 or VCC 4.3 pF 1. CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Section 5: Test circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x fIN + ICC/6 (per gate). Doc ID 6818 Rev 8 7/16 Test circuit 5 Note: 74LCX07 Test circuit Figure 4. Test circuit Table 10. Test circuit Test Switch tPLH, tPHL Open tPZL, tPLZ 6V tPZH, tPHZ GND CL = 50 pF or equivalent (includes jig and probe capacitance) RL = 500 Ω or equivalent RT = ZOUT of pulse generator (typically 50 Ω ). 8/16 Doc ID 6818 Rev 8 74LCX07 6 Waveforms Waveforms Figure 5. Waveform - propagation delay (f = 1 MHz; 50% duty cycle) Doc ID 6818 Rev 8 9/16 Package information 7 74LCX07 Package information In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance. ECOPACK specifications, grade definitions and product status are available at: www.st.com. ECOPACK is an ST trademark. 10/16 Doc ID 6818 Rev 8 74LCX07 Package information Figure 6. SO-14 package outline Table 11. SO-14 package mechanical data Dimensions Symbol mm Min. Typ. inch Max. Min. Typ. Max. A 1.35 1.75 0.053 0.069 A1 0.1 0.25 0.004 0.010 A2 1.10 1.65 0.043 0.065 B 0.33 0.51 0.013 0.020 C 0.19 0.25 0.007 0.010 D 8.55 8.75 0.337 0.344 E 3.8 4.0 0.150 0.157 e 1.27 0.050 H 5.8 6.2 0.228 0.244 h 0.25 0.50 0.010 0.020 L 0.4 1.27 0.016 0.050 k 0° 8° 0° 8° ddd 0.100 Doc ID 6818 Rev 8 0.004 11/16 Package information 74LCX07 Figure 7. TSSOP14 package outline Table 12. TSSOP14 package mechanical data Dimensions Symbol mm Min. Typ. A Max. Min. Typ. 1.2 A1 0.05 A2 0.8 b Max. 0.047 0.15 0.002 0.004 0.006 1.05 0.031 0.039 0.041 0.19 0.30 0.007 0.012 c 0.09 0.20 0.004 0.0089 D 4.9 5 5.1 0.193 0.197 0.201 E 6.2 6.4 6.6 0.244 0.252 0.260 E1 4.3 4.4 4.48 0.169 0.173 0.176 e 12/16 inch 1 0.65 BSC K 0° L 0.45 0.60 0.0256 BSC 8° 0° 0.75 0.018 Doc ID 6818 Rev 8 8° 0.024 0.030 74LCX07 Package information Figure 8. Tape and reel SO-14 outline Drawing is not in scale. Table 13. Tape and reel SO-14 mechanical data Dimensions Symbol mm Min. A Typ. inch Max. Min. 330 Max. 12.992 C 12.8 D 20.2 0.795 N 60 2.362 T 13.2 Typ. 0.504 22.4 0.519 0.882 Ao 6.4 6.6 0.252 0.260 Bo 9 9.2 0.354 0.362 Ko 2.1 2.3 0.082 0.090 Po 3.9 4.1 0.153 0.161 P 7.9 8.1 0.311 0.319 Doc ID 6818 Rev 8 13/16 Package information Figure 9. 74LCX07 Tape and reel TSSOP14 outline Drawing is not in scale. Table 14. Tape and reel TSSOP14 mechanical data Dimensions Symbol mm Min. A Max. Min. 330 13.2 Typ. Max. 12.992 C 12.8 D 20.2 0.795 N 60 2.362 T 14/16 Typ. inch 0.504 22.4 0.519 0.882 Ao 6.7 6.9 0.264 0.272 Bo 5.3 5.5 0.209 0.217 Ko 1.6 1.8 0.063 0.071 Po 3.9 4.1 0.153 0.161 P 7.9 8.1 0.311 0.319 Doc ID 6818 Rev 8 74LCX07 8 Revision history Revision history Table 15. Document revision history Date Revision 15-Sep-2004 4 Ordering codes revision - pag. 1. 10-Jul-2006 5 New template, temperature ranges updated 20-Jun-2012 6 Added Applications on page 1 Updated Table 1: Device summary on page 1 Updated Top in Table 5: Recommended operating conditions Updated ECOPACK® text in Section 7: Package information Minor textual updates 21-Jun-2012 7 Updated Table 1: Device summary 8 Updated ESD performance in Features (updated HBM and MM, added CDM). Added 74LCX07YMTR device and “Marking” to Table 1, updated temperature range and note 1. Updated Section 3: Maximum ratings (added cross-references). Removed “Operating temperature” from Table 5. Reformatted Section 7: Package information. Minor corrections throughout document. 02-Oct-2012 Changes Doc ID 6818 Rev 8 15/16 74LCX07 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY TWO AUTHORIZED ST REPRESENTATIVES, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2012 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 16/16 Doc ID 6818 Rev 8