74LVC245A

74LVC245A LOW VOLTAGE CMOS OCTAL BUS TRANSCEIVER (NOT INVERTED) HIGH PERFORMANCE s s s s s s s s s s 5V TOLERANT INPUTS HIGH SPEED: tPD = 6.3ns (MAX.) at VCC = 3V POWER DOWN PROTECTION ON INPUTS AND OUTPUTS SYMMETRICAL OUTPUT IMPEDANCE: |IOH| = IOL = 24mA (MIN) at VCC = 3V PCI BUS LEVELS GUARANTEED AT 24 mA BALANCED PROPAGATION DELAYS: tPLH ≅ tPHL OPERATING VOLTAGE RANGE: VCC(OPR) = 1.65V to 3.6V (1.2V Data Retention) PIN AND FUNCTION COMPATIBLE WITH 74 SERIES 245 LATCH-UP PERFORMANCE EXCEEDS 500mA (JESD 17) ESD PERFORMANCE: HBM > 2000V (MIL STD 883 method 3015); MM > 200V SOP TSSOP Table 1: Order Codes PACKAGE SOP TSSOP T&R 74LVC245AMTR 74LVC245ATTR DESCRIPTION The 74LVC245A is a low voltage CMOS OCTAL BUS TRANSCEIVER (3-STATE) fabricated with sub-micron silicon gate and double-layer metal wiring C2MOS technology. It is ideal for 1.65 to 3.6 VCC operations and low power and low noise applications. This IC is intended for two-way asynchronous communication between data buses and the Figure 1: Pin Connection And IEC Logic Symbols direction of data transmission is determined by DIR input. The enable input G can be used to disable the device so that the buses are effectively isolated. It has more speed performance at 3.3V than 5V AC/ACT family, combined with a lower power consumption. All inputs are equipped with protection circuits against static discharge, giving them 2KV ESD immunity and transient excess voltage. All floating bus terminals during High Z State must be held HIGH or LOW. July 2004 . Rev. 4 1/12 74LVC245A Figure 2: Input And Output Equivalent Circuit Table 2: Pin Description PIN N° 1 2, 3, 4, 5, 6, 7, 8, 9 18, 17, 16, 15, 14, 13, 12, 11 19 10 20 SYMBOL DIR A1 to A8 B1 to B8 NAME AND FUNCTION Directional Control Data Inputs/Outputs Data Inputs/Outputs Table 3: Truth Table INPUTS G L L H DIR L H X FUNCTION A BUS B BUS OUTPUT Yn A=B B=A Z OUTPUT INPUT INPUT OUTPUT Z Z G GND VCC Output Enable Input Ground (0V) Positive Supply Voltage X : Don’t Care Z : High Impedance Table 4: Absolute Maximum Ratings Symbol VCC VI VO VO IIK IOK IO Tstg TL Supply Voltage DC Input Voltage DC Output Voltage (High Impedance or VCC = 0V) DC Output Voltage (High or Low State) (note 1) DC Input Diode Current DC Output Diode Current (note 2) DC Output Current Storage Temperature Lead Temperature (10 sec) Parameter Value -0.5 to +7.0 -0.5 to +7.0 -0.5 to +7.0 -0.5 to VCC + 0.5 - 50 - 50 ± 50 ± 100 -65 to +150 300 Unit V V V V mA mA mA mA °C °C ICC or IGND DC VCC or Ground Current per Supply Pin Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is not implied 1) IO absolute maximum rating must be observed 2) VO < GND 2/12 74LVC245A Table 5: Recommended Operating Conditions Symbol VCC VI VO VO IOH, IOL IOH, IOL IOH, IOL IOH, IOL Top dt/dv Supply Voltage (note 1) Input Voltage Output Voltage (High Impedance or VCC = 0V) Output Voltage (High or Low State) High or Low Level Output Current (VCC = 3.0 to 3.6V) High or Low Level Output Current (VCC = 2.7 to 3.0V) High or Low Level Output Current (VCC = 2.3 to 2.7V) High or Low Level Output Current (VCC = 1.65 to 2.3V) Operating Temperature Input Rise and Fall Time (note 2) Parameter Value 1.65 to 3.6 0 to 5.5 0 to 5.5 0 to VCC ± 24 ± 12 ±8 ±4 -55 to 125 0 to 10 Unit V V V V mA mA mA mA °C ns/V 1) Truth Table guaranteed: 1.2V to 3.6V 2) VIN from 0.8V to 2V at VCC = 3.0V Table 6: DC Specifications Test Condition Symbol Parameter VCC (V) 1.65 to 1.95 2.3 to 2.7 2.7 to 3.6 1.65 to 1.95 2.3 to 2.7 2.7 to 3.6 1.65 to 3.6 1.65 2.3 2.7 3.0 3.0 VOL Low Level Output Voltage 1.65 to 3.6 1.65 2.3 2.7 3.0 II Ioff IOZ Input Leakage Current Power Off Leakage Current High Impedance Output Leakage Current Quiescent Supply Current ICC incr. per Input 3.6 0 3.6 IO=-100 µA IO=-4 mA IO=-8 mA IO=-12 mA IO=-18 mA IO=-24 mA IO=100 µA IO=4 mA IO=8 mA IO=12 mA IO=24 mA VI = 0 to 5.5V VI or VO = 5.5V VI = VIH orVIL VO = 0 to 5.5V VI = VCC or GND 3.6 2.7 to 3.6 VI or VO = 3.6 to 5.5V VIH = VCC-0.6V VCC-0.2 1.2 1.7 2.2 2.4 2.2 0.2 0.45 0.7 0.4 0.55 ±5 10 ± 10 -40 to 85 °C Min. 0.65VCC 1.7 2 0.35VCC 0.7 0.8 VCC-0.2 1.2 1.7 2.2 2.4 2.2 0.2 0.45 0.7 0.4 0.55 ±5 10 ± 10 µA µA µA V V Max. Value -55 to 125 °C Min. 0.65VCC 1.7 2 0.35VCC 0.7 0.8 V V Max. Unit VIH High Level Input Voltage Low Level Input Voltage High Level Output Voltage VIL VOH ICC 10 ± 10 500 10 ± 10 500 µA µA 3/12 ∆ICC 74LVC245A Table 7: Dynamic Switching Characteristics Test Condition Symbol Parameter VCC (V) 3.3 CL = 50pF VIL = 0V, VIH = 3.3V Value TA = 25 °C Min. Typ. 0.8 -0.8 Max. V Unit VOLP VOLV Dynamic Low Level Quiet Output (note 1) 1) Number of output defined as "n". Measured with "n-1" outputs switching from HIGH to LOW or LOW to HIGH. The remaining output is measured in the LOW state. Table 8: AC Electrical Characteristics Test Condition Symbol Parameter VCC (V) CL (pF) 30 30 50 50 30 30 50 50 30 30 50 50 RL (Ω ) 1000 500 500 500 1000 500 500 500 1000 500 500 500 ts = t r (ns) 2.0 2.0 2.5 2.5 2.0 2.0 2.5 2.5 2.0 2.0 2.5 2.5 -40 to 85 °C Min. 2.0 2.0 1.5 1.0 2.0 2.0 1.0 1.0 2.0 2.0 2.0 2.0 Max. 9.0 8.0 7.3 6.3 12 9.5 9.0 8.5 11 9.0 8.5 7.5 1 Value -55 to 125 °C Min. 2.0 2.0 1.5 1.0 2.0 2.0 1.0 1.0 2.0 2.0 2.0 2.0 Max. 12 10.5 8.8 7.6 16 12.5 11 10 14 12 10 9.0 1 Unit tPLH tPHL Propagation Delay Time tPZL tPZH tPLZ tPHZ tOSLH tOSHL 1.65 to 1.95 2.3 to 2.7 2.7 3.0 to 3.6 Output Enable Time 1.65 to 1.95 2.3 to 2.7 2.7 3.0 to 3.6 Output Disable Time 1.65 to 1.95 2.3 to 2.7 2.7 3.0 to 3.6 Output To Output 2.7 to 3.6 Skew Time (note1, 2) ns ns ns ns 1) Skew is defined as the absolute value of the difference between the actual propagation delay for any two outputs of the same device switching in the same direction, either HIGH or LOW (tOSLH = | tPLHm - tPLHn|, tOSHL = | tPHLm - tPHLn| 2) Parameter guaranteed by design Table 9: Capacitive Characteristics Test Condition Symbol Parameter VCC (V) Value TA = 25 °C Min. fIN = 10MHz Typ. 4 1.8 2.5 3.3 28 30 34 Max. pF pF Unit CIN CPD Input Capacitance Power Dissipation Capacitance (note 1) 1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x fIN + ICC/n (per circuit) 4/12 74LVC245A Figure 3: Test Circuit RT = ZOUT of pulse generator (typically 50Ω) Table 10: Test Circuit And Waveform Symbol Value Symbol 1.65 to 1.95V CL RL = R1 VS VIH VM VOH VX VY tr = tr 30pF 1000Ω 2 x VCC VCC VCC/2 VCC VOL + 0.15V VOH - 0.15V