74LVQ541TTR

74LVQ541 OCTAL BUS BUFFER WITH 3 STATE OUTPUTS (NON INVERTED) s s s s s s s s s s s HIGH SPEED: tPD =5.8 ns (TYP.) at VCC = 3.3 V COMPATIBLE WITH TTL OUTPUTS LOW POWER DISSIPATION: ICC = 4 µA (MAX.) at TA=25°C LOW NOISE: VOLP = 0.4V (TYP.) at VCC = 3.3V 75Ω TRANSMISSION LINE DRIVING CAPABILITY SYMMETRICAL OUTPUT IMPEDANCE: |IOH| = IOL = 12mA (MIN) at VCC = 3.0 V PCI BUS LEVELS GUARANTEED AT 24 mA BALANCED PROPAGATION DELAYS: tPLH ≅ tPHL OPERATING VOLTAGE RANGE: VCC(OPR) = 2V to 3.6V (1.2V Data Retention) PIN AND FUNCTION COMPATIBLE WITH 74 SERIES 541 IMPROVED LATCH-UP IMMUNITY SOP TSSOP Table 1: Order Codes PACKAGE SOP TSSOP T&R 74LVQ541MTR 74LVQ541TTR DESCRIPTION The 74LVQ541 is a low voltage CMOS OCTAL BUS BUFFER with 3 STATE OUTPUTS NON INVERTED fabricated with sub-micron silicon gate and double-layer metal wiring C2MOS technology. It is ideal for low power and low noise 3.3V applications. The 3-STATE control gate operates as two input and such that if either G1 and G2 are high, all eight outputs are in the high impedance state. In order to enhance PC board layout, the 74AC541 offers a pinout having inputs and outputs on opposite side of the package. All inputs and outputs are equipped with protection circuits against static discharge, giving them 2KV ESD immunity and transient excess voltage. Figure 1: Pin Connection And IEC Logic Symbols July 2004 Rev. 2 1/12 74LVQ541 Figure 2: Input And Output Equivalent Circuit Table 2: Pin Description PIN N° 1, 19 2, 3, 4, 5, 6, 7, 8, 9 18, 17, 16, 15, 14, 13, 12, 11 10 20 SYMBOL G1, G2 A1 to A8 Y1 to Y8 NAME AND FUNCTION Output Enable Inputs Data Inputs Data Outputs GND VCC Ground (0V) Positive Supply Voltage Table 3: Truth Table INPUTS G1 H X L L X : Don’t Care Z : High Impedance OUTPUT An X X L H Yn Z Z L H G2 X H L L Table 4: Absolute Maximum Ratings Symbol VCC VI VO IIK IOK IO Supply Voltage DC Input Voltage DC Output Voltage DC Input Diode Current DC Output Diode Current DC Output Current Parameter Value -0.5 to +7 -0.5 to VCC + 0.5 -0.5 to VCC + 0.5 ± 20 ± 20 ± 50 ± 400 -65 to +150 300 Unit V V V mA mA mA mA °C °C ICC or IGND DC VCC or Ground Current Tstg Storage Temperature TL Lead Temperature (10 sec) Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is not implied Table 5: Recommended Operating Conditions Symbol VCC VI VO Top dt/dv Supply Voltage (note 1) Input Voltage Output Voltage Operating Temperature Input Rise and Fall Time VCC = 3.0V (note 2) Parameter Value 2 to 3.6 0 to VCC 0 to VCC -55 to 125 0 to 10 Unit V V V °C ns/V 1) Truth Table guaranteed: 1.2V to 3.6V 2) VIN from 0.8V to 2V 2/12 74LVQ541 Table 6: DC Specifications Test Condition Symbol Parameter VCC (V) TA = 25°C Min. 2.0 0.8 IO=-50 µA 3.0 IO=-12 mA IO=-24 mA VOL Low Level Output Voltage IO=50 µA 3.0 IO=12 mA IO=24 mA II IOZ Input Leakage Current High Impedance Output Leakage Current Quiescent Supply Current Dynamic Output Current (note 1, 2) 3.6 3.6 3.6 3.6 VI = VCC or GND VI = VIH or VIL VO = VCC or GND VI = VCC or GND VOLD = 0.8 V max VOHD = 2 V min ± 0.1 ±0.25 4 36 -25 0.002 0 0.1 0.36 2.9 2.58 2.99 2.9 2.48 2.2 0.1 0.44 0.55 ±1 ± 2.5 40 25 -25 Typ. Max. Value -40 to 85°C Min. 2.0 0.8 2.9 2.48 2.2 0.1 0.44 0.55 ±1 ± 5.0 40 µA µA µA mA mA V V Max. -55 to 125°C Min. 2.0 0.8 Max. V V Unit VIH VIL VOH High Level Input Voltage Low Level Input Voltage High Level Output Voltage 3.0 to 3.6 ICC IOLD IOHD 1) Maximum test duration 2ms, one output loaded at time 2) Incident wave switching is guaranteed on transmission lines with impedances as low as 75Ω Table 7: Dynamic Switching Characteristics Test Condition Symbol Parameter VCC (V) 3.3 3.3 CL = 50 pF 3.3 0.8 V TA = 25°C Min. Typ. 0.5 -0.8 2 -0.6 Max. 0.8 V V Value -40 to 85°C Min. Max. -55 to 125°C Min. Max. Unit VOLP VOLV VIHD VILD Dynamic Low Voltage Quiet Output (note 1, 2) Dynamic High Voltage Input (note 1, 3) Dynamic Low Voltage Input (note 1, 3) 1) Worst case package. 2) Max number of outputs defined as (n). Data inputs are driven 0V to 3.3V, (n-1) outputs switching and one output at GND. 3) Max number of data inputs (n) switching. (n-1) switching 0V to 3.3V. Inputs under test switching: 3.3V to threshold (VILD), 0V to threshold (VIHD), f=1MHz. 3/12 74LVQ541 Table 8: AC Electrical Characteristics (CL = 50 pF, RL = 500 Ω, Input tr = tf = 3ns) Test Condition Symbol Parameter VCC (V) 2.7 3.3(*) 2.7 3.3(*) 2.7 3.3(*) 2.7 3.3 (*) Value TA = 25°C Min. Typ. 6.6 5.8 9.2 7.6 9.0 7.3 0.5 0.5 Max. 11 9 13.5 10 12 9.0 1.0 1.0 -40 to 85°C Min. Max. 12.5 10.5 15 11.5 13.5 10.5 1.0 1.0 -55 to 125°C Min. Max. 14 12 18 13 15 12 1.0 1.0 ns ns ns Unit tPLH tPHL Propagation Delay Time tPZL tPZH Output Enable Time tPLZ tPHZ Output Disable Time tOSLH tOSHL Output To Output Skew Time (note1, 2) ns 1) Skew is defined as the absolute value of the difference between the actual propagation delay for any two outputs of the same device switching in the same direction, either HIGH or LOW (tOSLH = |tPLHm - tPLHn|, tOSHL = |tPHLm - tPHLn|) 2) Parameter guaranteed by design (*) Voltage range is 3.3V ± 0.3V Table 9: Capacitive Characteristics Test Condition Symbol Parameter VCC (V) 3.3 3.3 3.3 fIN = 10MHz TA = 25°C Min. Typ. 4 8 10 Max. Value -40 to 85°C Min. Max. -55 to 125°C Min. Max. pF pF pF Unit CIN COUT CPD Input Capacitance Output Capacitance Power Dissipation Capacitance (note 1) 1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x fIN + ICC/8 (per Gate) 4/12 74LVQ541 Figure 3: Test Circuit TEST tPLH, tPHL tPZL, tPLZ tPZH, tPHZ CL = 50pF or equivalent (includes jig and probe capacitance) RL = R1 = 500Ω or equivalent RT = ZOUT of pulse generator (typically 50Ω) SWITCH Open 2VCC Open Figure 4: Waveform - Propagation Delays (f=1MHz; 50% duty cycle) 5/12 74LVQ541 Figure 5: Waveform - Output Enable And Disable Times (f=1MHz; 50% duty cycle) 6/12 74LVQ541 SO-20 MECHANICAL DATA DIM. A A1 B C D E e H h L k ddd 10.00 0.25 0.4 0° mm. MIN. 2.35 0.1 0.33 0.23 12.60 7.4 1.27 10.65 0.75 1.27 8° 0.100 0.394 0.010 0.016 0° TYP MAX. 2.65 0.30 0.51 0.32 13.00 7.6 MIN. 0.093 0.004 0.013 0.009 0.496 0.291 0.050 0.419 0.030 0.050 8° 0.004 inch TYP. MAX. 0.104 0.012 0.020 0.013 0.512 0.299 0016022D 7/12 74LVQ541 TSSOP20 MECHANICAL DATA mm. DIM. MIN. A A1 A2 b c D E E1 e K L 0˚ 0.45 0.60 0.05 0.8 0.19 0.09 6.4 6.2 4.3 6.5 6.4 4.4 0.65 BSC 8˚ 0.75 0˚ 0.018 0.024 1 TYP MAX. 1.2 0.15 1.05 0.30 0.20 6.6 6.6 4.48 0.002 0.031 0.007 0.004 0.252 0.244 0.169 0.256 0.252 0.173 0.0256 BSC 8˚ 0.030 0.004 0.039 MIN. TYP. MAX. 0.047 0.006 0.041 0.012 0.0079 0.260 0.260 0.176 inch A A2 A1 b e K c L E D E1 PIN 1 IDENTIFICATION 1 0087225C 8/12 74LVQ541 Tape & Reel SO-20 MECHANICAL DATA mm. DIM. MIN. A C D N T Ao Bo Ko Po P 10.8 13.2 3.1 3.9 11.9 12.8 20.2 60 30.4 11 13.4 3.3 4.1 12.1 0.425 0.520 0.122 0.153 0.468 TYP MAX. 330 13.2 0.504 0.795 2.362 1.197 0.433 0.528 0.130 0.161 0.476 MIN. TYP. MAX. 12.992 0.519 inch 9/12 74LVQ541 Tape & Reel TSSOP20 MECHANICAL DATA mm. DIM. MIN. A C D N T Ao Bo Ko Po P 6.8 6.9 1.7 3.9 11.9 12.8 20.2 60 22.4 7 7.1 1.9 4.1 12.1 0.268 0.272 0.067 0.153 0.468 TYP MAX. 330 13.2 0.504 0.795 2.362 0.882 0.276 0.280 0.075 0.161 0.476 MIN. TYP. MAX. 12.992 0.519 inch 10/12 74LVQ541 Table 10: Revision History Date 29-Jul-2004 Revision 2 Description of Changes Ordering Codes Revision - pag. 1. 11/12 74LVQ541 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics All other names are the property of their respective owners © 2004 STMicroelectronics - All Rights Reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 12/12