74LVX05TTR

74LVX05 LOW VOLTAGE CMOS HEX INVERTER (OPEN DRAIN) WITH 5V TOLERANT INPUTS ■ ■ ■ ■ ■ ■ ■ ■ ■ HIGH SPEED: tPD = 4.8ns (TYP.) at VCC = 3.3V 5V TOLERANT INPUTS INPUT VOLTAGE LEVEL: VIL=0.8V, VIH=2V at VCC=3V LOW POWER DISSIPATION: ICC = 2 µA (MAX.) at TA=25°C LOW NOISE: VOLP = 0.3V (TYP.) at VCC = 3.3V OPERATING VOLTAGE RANGE: VCC(OPR) = 2V to 3.6V (1.2V Data Retention) PIN AND FUNCTION COMPATIBLE WITH 74 SERIES 05 IMPROVED LATCH-UP IMMUNITY POWER DOWN PROTECTION ON INPUTS DESCRIPTION The 74LVX05 is a low voltage CMOS OPEN DRAIN HEX INVERTER fabricated with sub-micron silicon gate and double-layer metal wiring C2MOS technology. It is ideal for low power, battery operated and low noise 3.3V applications. The internal circuit is composed of 3 stages including buffer output, which provides high noise immunity and stable output. SOP TSSOP Table 1: Order Codes PACKAGE T&R SOP TSSOP 74LVX05MTR 74LVX05TTR Power down protection is provided on all inputs and 0 to 7V can be accepted on inputs with no regard to the supply voltage. This device can be used to interface 5V to 3V system. It combines high speed performance with the true CMOS low power consumption. All inputs and outputs are equipped with protection circuits against static discharge, giving them 2KV ESD immunity and transient excess voltage. Figure 1: Pin Connection And IEC Logic Symbols August 2004 Rev. 5 1/11 74LVX05 Figure 2: Input Equivalent Circuit Table 2: Pin Description PIN N° SYMBOL 1, 3, 5, 9, 11, 13 2, 4, 6, 8, 10, 12 7 14 NAME AND FUNCTION 1A to 6A Data Inputs 1Y to 6Y Data Outputs GND VCC Ground (0V) Positive Supply Voltage Table 3: Truth Table A Y L H Z L Z: High Impedance Table 4: Absolute Maximum Ratings Symbol VCC Parameter Value Unit Supply Voltage -0.5 to +7.0 V VI DC Input Voltage -0.5 to +7.0 V VO DC Output Voltage -0.5 to VCC + 0.5 V IIK DC Input Diode Current - 20 mA IOK DC Output Diode Current ± 20 mA IO DC Output Current ± 25 mA ± 50 mA -65 to +150 °C 300 °C ICC or IGND DC VCC or Ground Current Tstg Storage Temperature TL Lead Temperature (10 sec) Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is not implied. Table 5: Recommended Operating Conditions Symbol VCC Parameter Supply Voltage (note 1) Unit V VI Input Voltage 0 to 5.5 V VO Output Voltage 0 to VCC V Top Operating Temperature -55 to 125 °C 0 to 100 ns/V dt/dv Input Rise and Fall Time (note 2) (VCC = 3.3V) 1) Truth Table guaranteed: 1.2V to 3.6V 2) VIN from 0.8V to 2.0V 2/11 Value 2 to 3.6 74LVX05 Table 6: DC Specifications Test Condition Symbol VIH VIL VOL II IOZ ICC Parameter High Level Input Voltage Low Level Input Voltage Low Level Output Voltage Input Leakage Current High Impedance Output Leakage Current Quiescent Supply Current Value TA = 25°C VCC (V) Min. 2.0 3.0 3.6 2.0 3.0 3.6 Typ. Max. 1.5 2.0 2.4 -40 to 85°C -55 to 125°C Min. Min. Max. 1.5 2.0 2.4 2.0 IO=50 µA 0.0 0.0 Unit Max. 1.5 2.0 2.4 V 0.5 0.8 0.8 0.5 0.8 0.8 0.5 0.8 0.8 0.1 0.1 0.1 V 3.0 IO=50 µA 0.1 0.1 0.1 3.0 IO=4 mA 0.36 0.44 0.55 3.6 VI = 5V or GND ± 0.1 ±1 ±1 µA 3.6 VI = VIH or VIL VO = VCC or GND ±0.25 ± 2.5 ±5 µA 3.6 VI = VCC or GND 2 20 20 µA V Table 7: Dynamic Switching Characteristics Test Condition Symbol Parameter VOLP Dynamic Low Voltage Quiet Output (note 1, 2) Dynamic High Voltage Input (note 1, 3) Dynamic Low Voltage Input (note 1, 3) VOLV VIHD VILD Value TA = 25°C VCC (V) Min. 3.3 -0.5 3.3 Typ. Max. 0.3 0.5 -55 to 125°C Min. Min. Max. Unit Max. -0.3 2 CL = 50 pF 3.3 -40 to 85°C V 0.8 1) Worst case package. 2) Max number of outputs defined as (n). Data inputs are driven 0V to 3.3V, (n-1) outputs switching and one output at GND. 3) Max number of data inputs (n) switching. (n-1) switching 0V to 3.3V. Inputs under test switching: 3.3V to threshold (VILD), 0V to threshold (VIHD), f=1MHz. 3/11 74LVX05 Table 8: AC Electrical Characteristics (Input tr = tf = 3ns) Test Condition Symbol tPZL tPLZ tOSLH tOSHL Parameter Propagation Delay Time Propagation Delay Time Output To Output Skew Time (note1, 2) VCC (V) CL (pF) 2.7 2.7 Value TA = 25°C Min. -40 to 85°C -55 to 125°C Min. Min. Typ. Max. 15 50 5.4 6.0 7.7 8.7 9.0 10.0 10.0 11.5 3.3(*) 15 4.8 7.0 8.1 9.0 3.3(*) 2.7 50 5.3 7.6 50 3.3(*) 2.7 50 10.5 9.6 14.7 13.5 0.5 0.5 1.0 1.0 50 (*) 3.3 50 Max. 8.8 1.0 1.0 15.0 14.0 Unit Max. ns 9.5 1.0 1.0 1.5 1.5 16.0 15.0 ns 1.5 1.5 ns 1) Skew is defined as the absolute value of the difference between the actual propagation delay for any two outputs of the same device switching in the same direction, either HIGH or LOW 2) Parameter guaranteed by design (*) Voltage range is 3.3V ± 0.3V Table 9: Capacitive Characteristics Test Condition Symbol CIN Parameter VCC (V) Value TA = 25°C Min. Typ. Max. 10 -40 to 85°C -55 to 125°C Min. Min. Max. Unit Max. Input Capacitance 3.3 5.4 COUT Output Capacitance 3.3 7.3 pF CPD Power Dissipation Capacitance (note 1) 3.3 2.6 pF 10 10 pF 1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x fIN + ICC/6 (per gate) Figure 3: Test Circuit CL = 15/50pF or equivalent (includes jig and probe capacitance) RL = R1 = 1KΩ or equivalent RT = ZOUT of pulse generator (typically 50Ω) 4/11 74LVX05 Figure 4: Waveform - Propagation Delays (f=1MHz; 50% duty cycle) 5/11 74LVX05 SO-14 MECHANICAL DATA DIM. mm. MIN. TYP inch MAX. MIN. TYP. MAX. A 1.35 1.75 0.053 0.069 A1 0.1 0.25 0.004 0.010 A2 1.10 1.65 0.043 0.065 B 0.33 0.51 0.013 0.020 C 0.19 0.25 0.007 0.010 D 8.55 8.75 0.337 0.344 E 3.8 4.0 0.150 0.157 e 1.27 0.050 H 5.8 6.2 0.228 0.244 h 0.25 0.50 0.010 0.020 L 0.4 1.27 0.016 0.050 k 0° 8° 0° 8° ddd 0.100 0.004 0016019D 6/11 74LVX05 TSSOP14 MECHANICAL DATA mm. inch DIM. MIN. TYP A MAX. MIN. TYP. MAX. 1.2 A1 0.05 A2 0.8 b 0.047 0.15 0.002 0.004 0.006 1.05 0.031 0.039 0.041 0.19 0.30 0.007 0.012 c 0.09 0.20 0.004 0.0089 D 4.9 5 5.1 0.193 0.197 0.201 E 6.2 6.4 6.6 0.244 0.252 0.260 E1 4.3 4.4 4.48 0.169 0.173 0.176 1 e 0.65 BSC K 0˚ L 0.45 A 0.60 0.0256 BSC 8˚ 0˚ 0.75 0.018 8˚ 0.024 0.030 A2 A1 b e K c L E D E1 PIN 1 IDENTIFICATION 1 0080337D 7/11 74LVX05 Tape & Reel SO-14 MECHANICAL DATA mm. inch DIM. MIN. A MAX. MIN. 330 13.2 TYP. MAX. 12.992 C 12.8 D 20.2 0.795 N 60 2.362 T 8/11 TYP 0.504 22.4 0.519 0.882 Ao 6.4 6.6 0.252 0.260 Bo 9 9.2 0.354 0.362 Ko 2.1 2.3 0.082 0.090 Po 3.9 4.1 0.153 0.161 P 7.9 8.1 0.311 0.319 74LVX05 Tape & Reel TSSOP14 MECHANICAL DATA mm. inch DIM. MIN. A TYP MAX. MIN. 330 MAX. 12.992 C 12.8 D 20.2 0.795 N 60 2.362 T 13.2 TYP. 0.504 22.4 0.519 0.882 Ao 6.7 6.9 0.264 0.272 Bo 5.3 5.5 0.209 0.217 Ko 1.6 1.8 0.063 0.071 Po 3.9 4.1 0.153 0.161 P 7.9 8.1 0.311 0.319 9/11 74LVX05 Table 10: Revision History Date Revision 27-Aug-2004 5 10/11 Description of Changes Ordering Codes Revision - pag. 1. 74LVX05 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics All other names are the property of their respective owners © 2004 STMicroelectronics - All Rights Reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 11/11