74V1G66STR

74V1G66 SINGLE BILATERAL SWITCH s s s s s s HIGH SPEED: tPD = 0.3ns (TYP.) at VCC = 5V tPD = 0.4ns (TYP.) at VCC = 3.3V LOW POWER DISSIPATION: ICC = 1µA(MAX.) at TA=25°C LOW "ON" RESISTANCE: RON =6.5Ω (TYP.) AT VCC = 5V II/O = 1mA RON = 8.5Ω (TYP.) AT VCC = 3.3V II/O = 1mA SINE WAVE DISTORTION: 0.04% AT VCC = 3.3V f = 1KHz WIDE OPERATING RANGE: VCC (OPR) = 2V TO 5.5V IMPROVED LATCH-UP IMMUNITY SOT23-5L SOT323-5L ORDER CODES PACKAGE SOT23-5L SOT323-5L T&R 74V1G66STR 74V1G66CTR DESCRIPTION The 74V1G66 is an advanced high-speed CMOS SINGLE BILATERAL SWITCH fabricated in silicon gate C2MOS technology. It achieves high speed propagation delay and VERY LOW ON resistances while maintaining true CMOS low power consumption. This bilateral switch handles rail to rail analog and digital signals that may vary across the full power supply range (from GND to VCC). The C input is provided to control the switch and it’s compatible with standard CMOS output; the switch is ON (port I/O is connected to Port O/I) when the C input is held high and OFF (high impedance state exists between the two ports) when C is held low. It can be used in many application as Battery Powered System, Test Equipment. It’s available in the commercial and extended temperature range in SOT23-5L and SC-70-5L package. All inputs and output are equipped with protection circuits against static discharge, giving them ESD immunity and transient excess voltage PIN CONNECTION AND IEC LOGIC SYMBOLS April 2004 1/11 74V1G66 INPUT EQUIVALENT CIRCUIT PIN DESCRIPTION PIN N° 1 2 4 3 5 SYMBOL I/O O/I C GND VCC NAME AND FUNCTION Independent Input/Output Independent Output/Input Enable Input (Active HIGH) Ground (0V) Positive Supply Voltage TRUTH TABLE CONTROL H L * : High Impedance State SWITCH FUNCTION ON OFF * ABSOLUTE MAXIMUM RATINGS Symbol VCC VI VIC VO IIK IIK IOK IO Supply Voltage DC Input Voltage DC Control Input Voltage DC Output Voltage DC Input Diode Current DC Control Input Diode Current DC Output Diode Current DC Output Current Parameter Value -0.5 to +7.0 -0.5 to VCC + 0.5 -0.5 to +7.0 -0.5 to VCC + 0.5 ± 20 - 20 ± 20 ± 50 ± 50 -65 to +150 300 Unit V V V V mA mA mA mA mA °C °C ICC or IGND DC VCC or Ground Current Storage Temperature Tstg TL Lead Temperature (10 sec) Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is not implied RECOMMENDED OPERATING CONDITIONS Symbol VCC VI VIC VO Top dt/dv Supply Voltage Input Voltage Control Input Voltage Output Voltage Operating Temperature Input Rise and Fall Time (note 1) VCC = 5.0V Parameter Value 2 to 5.5 0 to VCC 0 to 5.5 0 to VCC -55 to 125 0 to 20 Unit V V V V °C ns/V 1) VIN from 30% to 70% of VCC on control pin 2/11 74V1G66 DC SPECIFICATIONS Test Condition Symbol Parameter VCC (V) 2.0 2.7 to 5.5 2.0 2.7 to 5.5 VIC = VIH VI/O = VCC to GND 5.0(**) II/O ≤ 1mA 3.3(*) 3.3(*) 5.0(**) IOFF Input/Output Leakage Current (SWITCH OFF) Switch Input Leakage Current (SWITCH ON, OUTPUT OPEN) Control Input Leakage Current Quiescent Supply Current VIC = VIH VI/O = VCC or GND II/O ≤ 1mA VOS = VCC to GND VIS = VCC to GND VIC = VIL VOS = VCC to GND VIC = VIH VIC = 5.5V or GND VI = VCC or GND TA = 25°C Min. 1.5 0.7VCC 0.5 0.3VCC 12.5 7.5 8.5 6.5 19 10 10.5 8.5 ±0.1 Typ. Max. Value -40 to 85°C Min. 1.5 0.7VCC 0.5 0.3VCC 23 12 12.5 10 ±1 Max. -55 to 125°C Min. 1.5 0.7VCC 0.5 0.3VCC 27 14 15 12 ±5 Ω Ω V V Max. Unit VIH High Level Input Voltage Low Level Input Voltage ON Resistance VIL RON RON ON Resistance 5.5 µA IIZ 5.5 0 to 5.5 5.5 ±0.1 ± 0.1 1 ±1 ± 1.0 10 ±5 ± 1.0 20 µA µA µA IIN ICC (*) Voltage range is 3.3V ± 0.3V (**) Voltage range is 5V ± 0.5V AC ELECTRICAL CHARACTERISTICS (CL = 50pF, Input tr = tf = 3ns) Test Condition Symbol Parameter VCC (V) 3.3 (*) Value TA = 25°C Min. Typ. 0.4 0.3 5.0 5.0 2.5 2.0 Max. 0.8 0.6 7.5 7.5 4.0 4.0 -40 to 85°C Min. Max. 1.2 1.0 9.0 9.0 5.0 5.0 -55 to 125°C Min. Max. 2.4 2.0 10.0 10.0 7.0 7.0 ns ns Unit tPD tPLZ tPHZ tPZL tPZH Delay Time 5.0(**) Output Disable Time Output Enable Time 3.3(*) 5.0(**) 3.3(*) 5.0 (**) tr = tf = 6ns RL = 500 Ω RL = 1 K Ω ns (*) Voltage range is 3.3V ± 0.3V (**) Voltage range is 5.0V ± 0.5V 3/11 74V1G66 CAPACITIVE CHARACTERISTICS Test Condition Symbol Parameter VCC (V) TA = 25°C Min. Typ. 3 10 3.3 5.0 2.5 3 pF Max. 10 Value -40 to 85°C Min. Max. 10 -55 to 125°C Min. Max. 10 pF pF Unit CIN CI/O CPD Input Capacitance Output Capacitance Power Dissipation Capacitance (note 1) 1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x fIN + ICC ANALOG SWITCH CHARACTERISTICS (GND = 0V; TA = 25°C) Test Condition Symbol Parameter VCC (V) 3.3(*) 5.0(**) 3.3(*) 5.0(**) 3.3(*) 5.0(**) 3.3(*) 5.0 (**) Value Unit Typ. VIN (Vp-p) 2.75 4 fIN = 1 KHz RL = 10 KΩ, CL = 50 pF Adjust fIN voltage to obtain 0 dBm at VOS. Increase fIN Frequency until dB meter reads -3dB RL = 50Ω, CL = 10 pF VIN is centered at VCC/2 Adjust fIN Voltage to obtained 0dBm at VIS RL = 600Ω, CL = 50 pF, fIN = 1KHz sine wave RL = 600Ω, CL = 50 pF, fIN = 1KHz square wave tr = tf = 6ns Sine Wave Distortion (THD) fMAX Frequency Response (Switch ON) Feed through Attenuation (Switch OFF) Crosstalk (Control Input to Signal Output) (*)Voltage range is 3.3V ± 0.3V (**) Voltage range is 5.0V ± 0.5V 0.04 0.04 150 180 -60 -60 60 60 mV dB MHz % 4/11 74V1G66 SWITCHING CARACTERISTICS TEST CIRCUIT FEEDTHROUGH ATTENUATION BANDWIDTH ATTENUATION MAXIMUM CONTROL FREQUENCY CROSSTALK (control to output 5/11 74V1G66 CHANNEL RESISTANCE (RON) ICC (Opr.) 6/11 74V1G66 SOT23-5L MECHANICAL DATA mm. DIM. MIN. A A1 A2 b C D E e H L 2.60 0.10 0.90 0.00 0.90 0.35 0.09 2.80 1.50 0.95 3.00 0.60 102.3 3.9 TYP MAX. 1.45 0.10 1.30 0.50 0.20 3.00 1.75 MIN. 35.4 0.0 35.4 13.7 3.5 110.2 59.0 37.4 118.1 23.6 TYP. MAX. 57.1 3.9 51.2 19.7 7.8 118.1 68.8 mils . 7049676C 7/11 74V1G66 SOT323-5L MECHANICAL DATA mm. DIM. MIN. A A1 A2 b C D E E1 e e1 L 0.10 0.80 0.00 0.80 0.15 0.10 1.80 1.80 1.15 0 .65 1.3 0.30 3.9 TYP MAX. 1.10 0.10 1.00 0.30 0.18 2.20 2.40 1.35 MIN. 31.5 0.0 31.5 5.9 3.9 70.9 70.9 45.3 25.6 51.2 11.8 TYP. MAX. 43.3 3.9 39.4 11.8 7.1 86.6 94.5 53.1 mils 8/11 74V1G66 Tape & Reel SOT23-xL MECHANICAL DATA mm. DIM. MIN. A C D N T Ao Bo Ko Po P 3.13 3.07 1.27 3.9 3.9 3.23 3.17 1.37 4.0 4.0 12.8 20.2 60 14.4 3.33 3.27 1.47 4.1 4.1 0.123 0.120 0.050 0.153 0.153 0.127 0.124 0.054 0.157 0.157 13.0 TYP MAX. 180 13.2 0.504 0.795 2.362 0.567 0.131 0.128 0.0.58 0.161 0.161 0.512 MIN. TYP. MAX. 7.086 0.519 inch 9/11 74V1G66 Tape & Reel SOT323-xL MECHANICAL DATA mm. DIM. MIN. A C D N T Ao Bo Ko Po P 3.9 3.8 2.25 2.7 1.2 4 4 4.1 4.2 0.153 0.149 175 12.8 20.2 59.5 60 60.5 14.4 0.088 0.106 0.047 0.157 0.157 0.161 0.165 TYP 180 13 MAX. 185 13.2 MIN. 6.889 0.504 0.795 2.362 0.567 TYP. 7.086 0.512 MAX. 7.283 0.519 inch 10/11 74V1G66 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics All other names are the property of their respective owners © 2004 STMicroelectronics - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States. http://www.st.com 11/11