74V2GU04

74V2GU04 TRIPLE INVERTER (SINGLE STAGE) s s s s s s s s HIGH SPEED: tPD = 3.5ns (TYP.) at VCC = 5V LOW POWER DISSIPATION: ICC = 1µA(MAX.) at TA = 25°C HIGH NOISE IMMUNITY: VNIH = VNIL = 10% VCC (MIN.) POWER DOWN PROTECTION ON INPUT SYMMETRICAL OUTPUT IMPEDANCE: |IOH| = IOL = 8mA (MIN) at VCC = 4.5V BALANCED PROPAGATION DELAYS: tPLH ≅ tPHL OPERATING VOLTAGE RANGE: VCC(OPR) = 2V to 5.5V IMPROVED LATCH-UP IMMUNITY SOT23-8L SOT323-8L ORDER CODES PACKAGE SOT23-8L T&R 74V2GU04STR DESCRIPTION The 74V2GU04 is an advanced high-speed CMOS TRIPLE INVERTER (SINGLE STAGE) fabricated with sub-micron silicon gate and double-layer metal wiring C2MOS technology. The internal circuit is composed of a single stages inverter, then an unbuffered output. It can be used in analog application such a crystal oscillator. Power down protection is provided on input and 0 to 7V can be accepted on input with no regard to the supply voltage. This device can be used to interface 5V to 3V. PIN CONNECTION AND IEC LOGIC SYMBOLS June 2003 1/7 74V2GU04 INPUT EQUIVALENT CIRCUIT PIN DESCRIPTION PIN No 1, 3, 6 7, 5, 2 4 8 SYMBOL 1A, 2A, 3A 1Y, 2Y, 3Y GND VCC NAME QND FUNCTION Data Inputs Data Outputs Ground (0V) Positive Supply Voltage TRUTH TABLE A L H Y H L ABSOLUTE MAXIMUM RATINGS Symbol VCC VI VO IIK IOK IO Supply Voltage DC Input Voltage DC Output Voltage DC Input Diode Current DC Output Diode Current DC Output Current Parameter Value -0.5 to +7.0 -0.5 to +7.0 -0.5 to VCC + 0.5 - 20 ± 20 ± 25 ± 50 -65 to +150 260 Unit V V V mA mA mA mA °C °C ICC or IGND DC VCC or Ground Current Storage Temperature Tstg TL Lead Temperature (10 sec) Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is not implied. RECOMMENDED OPERATING CONDITIONS Symbol VCC VI VO Top Supply Voltage Input Voltage Output Voltage Operating Temperature Parameter Value 2 to 5.5 0 to 5.5 0 to VCC -55 to 125 Unit V V V °C 2/7 74V2GU04 DC SPECIFICATIONS Test Condition Symbol Parameter VCC (V) 2.0 3.0 to 5.5 2.0 3.0 to 5.5 2.0 3.0 4.5 3.0 4.5 VOL Low Level Output Voltage 2.0 3.0 4.5 3.0 4.5 II ICC Input Leakage Current Quiescent Supply Current 0 to 5.5 5.5 IO=-50 µA IO=-50 µA IO=-50 µA IO=-4 mA IO=-8 mA IO=50 µA IO=50 µA IO=50 µA IO=4 mA IO=8 mA VI = 5.5V or GND VI = VCC or GND TA = 25°C Min. 1.7 0.8VCC 0.3 0.2VCC 1.8 2.7 4.0 2.58 3.94 0.0 0.0 0.0 0.2 0.3 0.5 0.36 0.36 ± 0.1 1 2.0 3.0 4.5 1.8 2.7 4.0 2.48 3.8 0.2 0.3 0.5 0.44 0.44 ±1 10 Typ. Max. Value -40 to 85°C Min. 1.7 0.8VCC 0.3 0.2VCC 1.8 2.7 4.0 2.4 3.7 0.2 0.3 0.5 0.55 0.55 ±1 20 µA µA V V Max. -55 to 125°C Min. 1.7 0.8VCC 0.3 0.2VCC V V Max. Unit VIH High Level Input Voltage Low Level Input Voltage High Level Output Voltage VIL VOH AC ELECTRICAL CHARACTERISTICS (Input tr = tf = 3ns) Test Condition Symbol Parameter VCC (V) 3.3 3.3 (*) (*) Value TA = 25°C Min. Typ. 4.4 4.8 3.5 4.1 Max. 6.5 7.0 5.5 6.0 -40 to 85°C Min. 1.0 1.0 1.0 1.0 Max. 8.0 9.0 6.0 7.0 -55 to 125°C Min. 1.0 1.0 1.0 1.0 Max. 9.0 10.0 7.5 8.0 ns Unit CL (pF) 15 50 15 50 tPLH tPHL Propagation Delay Time 5.0(**) 5.0(**) (*) Voltage range is 3.3V ± 0.3V (**) Voltage range is 5.0V ± 0.5V CAPACITIVE CHARACTERISTICS Test Condition Symbol Parameter Min. CIN CPD Input Capacitance Power Dissipation Capacitance (note 1) TA = 25°C Typ. 5 10 Max. 10 Value -40 to 85°C Min. Max. 10 -55 to 125°C Min. Max. 10 pF pF Unit 1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x fIN + ICC 3/7 74V2GU04 TEST CIRCUIT CL = 15/50pF or equivalent (includes jig and probe capacitance) RT = ZOUT of pulse generator (typically 50Ω) WAVEFORM: PROPAGATION DELAY (f=1MHz; 50% duty cycle) 4/7 74V2GU04 SOT23-8L MECHANICAL DATA mm. DIM. MIN. A A1 A2 b C D E E1 e e1 L 0.35 0.90 0.00 0.90 0.22 0.09 2.80 2.60 1.50 0 .65 1.95 0.55 13.7 TYP MAX. 1.45 0.15 1.30 0.38 0.20 3.00 3.00 1.75 MIN. 35.4 0.0 35.4 8.6 3.5 110.2 102.3 59.0 25.6 76.7 21.6 TYP. MAX. 57.1 5.9 51.2 14.9 7.8 118.1 118.1 68.8 mils 5/7 74V2GU04 Tape & Reel SOT23-xL MECHANICAL DATA mm. DIM. MIN. A C D N T Ao Bo Ko Po P 3.13 3.07 1.27 3.9 3.9 3.23 3.17 1.37 4.0 4.0 12.8 20.2 60 14.4 3.33 3.27 1.47 4.1 4.1 0.123 0.120 0.050 0.153 0.153 0.127 0.124 0.054 0.157 0.157 13.0 TYP MAX. 180 13.2 0.504 0.795 2.362 0.567 0.131 0.128 0.0.58 0.161 0.161 0.512 MIN. TYP. MAX. 7.086 0.519 inch 6/7 74V2GU04 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. © The ST logo is a registered trademark of STMicroelectronics © 2003 STMicroelectronics - Printed in Italy - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - Canada - China - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco Singapore - Spain - Sweden - Switzerland - United Kingdom - United States. © http://www.st.com 7/7