74V2T00

74V2T00 DUAL 2-INPUT NAND GATE s s s s s s s HIGH SPEED: tPD = 5ns (TYP.) at VCC = 5V LOW POWER DISSIPATION: ICC = 1µA(MAX.) at TA = 25°C COMPATIBLE WITH TTL OUTPUTS: VIH = 2V (MIN), VIL = 0.8V (MAX) POWER DOWN PROTECTION ON INPUTS SYMMETRICAL OUTPUT IMPEDANCE: |IOH| = IOL = 8mA (MIN) BALANCED PROPAGATION DELAYS: tPLH ≅ tPHL OPERATING VOLTAGE RANGE: VCC(OPR) = 4.5V to 5.5V IMPROVED LATCH-UP IMMUNITY SOT23-8L ORDER CODES PACKAGE SOT23-8L T&R 74V2T00STR DESCRIPTION The 74V2T00 is an advanced high-speed CMOS DUAL 2-INPUT NAND GATE fabricated with sub-micron silicon gate and double-layer metal wiring C2MOS technology. The internal circuit is composed of 3 stages including buffer output, which provide high noise immunity and stable output. Power down protection is provided on all inputs and 0 to 7V can be accepted on inputs with no regard to the supply voltage. This device can be used to interface 5V to 3V. PIN CONNECTION AND IEC LOGIC SYMBOLS June 2003 1/7 74V2T00 INPUT AND OUTPUT EQUIVALENT CIRCUIT PIN DESCRIPTION PIN N° 1, 5 2, 6 7, 3 4 8 SYMBOL 1A, 2A 1B, 2B 1Y, 2Y GND VCC NAME QND FUNCTION Data Input Data Input Data Output Ground (0V) Positive Supply Voltage TRUTH TABLE A L L H H B L H L H Y H H H L ABSOLUTE MAXIMUM RATINGS Symbol VCC VI VO IIK IOK IO Tstg TL Supply Voltage DC Input Voltage DC Output Voltage DC Input Diode Current DC Output Diode Current DC Output Current Storage Temperature Lead Temperature (10 sec) Parameter Value -0.5 to +7.0 -0.5 to +7.0 -0.5 to VCC + 0.5 - 20 ± 20 ± 25 ± 50 -65 to +150 300 Unit V V V mA mA mA mA °C °C ICC or IGND DC VCC or Ground Current Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these condition is not implied RECOMMENDED OPERATING CONDITIONS Symbol VCC VI VO Top dt/dv Supply Voltage Input Voltage Output Voltage Operating Temperature Input Rise and Fall Time (note 1) (VCC = 5.0 ± 0.5V) Parameter Value 4.5 to 5.5 0 to 5.5 0 to VCC -55 to 125 0 to 20 Unit V V V °C ns/V 1) VIN from 0.8V to 2V 2/7 74V2T00 DC SPECIFICATION Test Condition Symbol Parameter VCC (V) 4.5 to 5.5 4.5 to 5.5 4.5 4.5 4.5 4.5 0 to 5.5 5.5 5.5 IO=-50 µA IO=-8 mA IO=50 µA IO=8 mA VI = 5.5V or GND VI = VCC or GND One Input at 3.4V, other input at VCC or GND TA = 25°C Min. 2 0.8 4.4 3.94 0.0 0.1 0.36 ± 0.1 1 1.35 4.5 4.4 3.8 0.1 0.44 ± 1.0 10 1.5 Typ. Max. Value -40 to 85°C Min. 2 0.8 4.4 3.7 0.1 0.55 ± 1.0 20 1.5 µA µA mA V Max. -55 to 125°C Min. 2 0.8 Max. V V V Unit VIH VIL VOH VOL II ICC ∆ICC High Level Input Voltage Low Level Input Voltage High Level Output Voltage Low Level Output Voltage Input Leakage Current Quiescent Supply Current Additional Worst Case Supply Current AC ELECTRICAL CHARACTERISTICS (Input tr = tf = 3ns) Test Condition Symbol Parameter VCC (V) 5.0 (*) 5.0 (*) CL (pF) 15 50 TA = 25°C Min. Typ. 5.0 5.5 Max. 7.0 8.0 Value -40 to 85°C Min. 1.0 1.0 Max. 8.0 9.0 -55 to 125°C Min. 1.0 1.0 Max. 8.0 9.0 ns Unit tPLH tPHL Propagation Delay Time (*) Voltage range is 5.0V ± 0.5V CAPACITANCE CHARACTERISTICS Test Condition Symbol Parameter Min. CIN CPD Input Capacitance Power Dissipation Capacitance (note 1) TA = 25°C Typ. 4 10.5 Max. 10 Value -40 to 85°C Min. Max. 10 -55 to 125°C Min. Max. 10 pF pF Unit 1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average current can be obtained by the following equation. ICC(opr) = CPD x VCC x fIN + ICC/2 3/7 74V2T00 TEST CIRCUIT CL = 50pF or equivalent (includes jig and probe capacitance) RT = ZOUT of pulse generator (typically 50Ω) WAVEFORM: PROPAGATION DELAY (f=1MHz; 50% duty cycle) 4/7 74V2T00 SOT23-8L MECHANICAL DATA mm. DIM. MIN. A A1 A2 b C D E E1 e e1 L 0.35 0.90 0.00 0.90 0.22 0.09 2.80 2.60 1.50 0 .65 1.95 0.55 13.7 TYP MAX. 1.45 0.15 1.30 0.38 0.20 3.00 3.00 1.75 MIN. 35.4 0.0 35.4 8.6 3.5 110.2 102.3 59.0 25.6 76.7 21.6 TYP. MAX. 57.1 5.9 51.2 14.9 7.8 118.1 118.1 68.8 mils 5/7 74V2T00 Tape & Reel SOT23-xL MECHANICAL DATA mm. DIM. MIN. A C D N T Ao Bo Ko Po P 3.13 3.07 1.27 3.9 3.9 3.23 3.17 1.37 4.0 4.0 12.8 20.2 60 14.4 3.33 3.27 1.47 4.1 4.1 0.123 0.120 0.050 0.153 0.153 0.127 0.124 0.054 0.157 0.157 13.0 TYP MAX. 180 13.2 0.504 0.795 2.362 0.567 0.131 0.128 0.0.58 0.161 0.161 0.512 MIN. TYP. MAX. 7.086 0.519 inch 6/7 74V2T00 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. © The ST logo is a registered trademark of STMicroelectronics © 2003 STMicroelectronics - Printed in Italy - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - Canada - China - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco Singapore - Spain - Sweden - Switzerland - United Kingdom - United States. © http://www.st.com 7/7