74V2T66

74V2T66 DUAL BILATERAL SWITCH s s s s s s s HIGH SPEED: tPD = 0.6ns (TYP.) at VCC = 5V COMPATIBLE WITH TTL LEVEL LOW POWER DISSIPATION: ICC = 1µA(MAX.) at TA = 25°C LOW "ON" RESISTANCE: RON =10Ω (TYP.) AT VCC = 5V II/O = 1mA SINE WAVE DISTORTION: 0.04% AT VCC = 5.0V, f = 1KHz OPERATING VOLTAGE RANGE: VCC (OPR) = 4.5V TO 5.5V IMPROVED LATCH-UP IMMUNITY SOT23-8L ORDER CODES PACKAGE SOT23-8L T&R 74V2T66STR DESCRIPTION The 74V2T66 is an advanced high-speed CMOS DUAL BILATERAL SWITCH fabricated in silicon gate C2MOS technology. It achieves high speed propagation delay and VERY LOW ON resistances while maintaining true CMOS low power consumption. This bilateral switch handles rail to rail analog and digital signals that may vary across the full power supply range (from GND to VCC) The C input is provided to control the switch and it’s compatible with standard CMOS output; the switch is ON (port I/O is connected to Port O/I) when the C input is held high and OFF (high impedance state exists between the two ports) when C is held low. It can be used in many application as Battery Powered System, Test Equipment. It’s available in the commercial and extended temperature range in SOT23-8L package. All inputs and output are equipped with protection circuits against static discharge, giving them ESD immunity and transient excess voltage. PIN CONNECTION AND IEC LOGIC SYMBOLS June 2003 1/9 74V2T66 INPUT EQUIVALENT CIRCUIT PIN DESCRIPTION PIN No 1, 5 2, 6 7, 3 4 8 SYMBOL 1I/O, 2I/O 1O/I, 2O/I 1C, 2C GND VCC NAME AND FUNCTION Independent Input/Output Independent Output/Input Enable Input (Active HIGH) Ground (0V) Positive Supply Voltage TRUTH TABLE CONTROL H L * : High Impedance State SWITCH FUNCTION ON OFF * ABSOLUTE MAXIMUM RATINGS Symbol VCC VI VIC VO IIK IIK IOK IO Tstg TL Supply Voltage DC Input Voltage DC Control Input Voltage DC Output Voltage DC Input Diode Current DC Control Input Diode Current DC Output Diode Current DC Output Current Storage Temperature Lead Temperature (10 sec) Parameter Value -0.5 to +7.0 -0.5 to VCC + 0.5 -0.5 to +7.0 -0.5 to VCC + 0.5 ± 20 - 20 ± 20 ± 50 ± 50 -65 to +150 300 Unit V V V V mA mA mA mA mA °C °C ICC or IGND DC VCC or Ground Current Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is not implied RECOMMENDED OPERATING CONDITIONS Symbol VCC VI VIC VO Top dt/dv Supply Voltage Input Voltage Control Input Voltage Output Voltage Operating Temperature Input Rise and Fall Time (note 1) VCC = 5.0V Parameter Value 4.5 to 5.5 0 to VCC 0 to 5.5 0 to VCC -55 to 125 0 to 20 Unit V V V V °C ns/V 1) VIN from 0.8V to 2V on control pin 2/9 74V2T66 DC SPECIFICATIONS Test Condition Symbol Parameter VCC (V) 5.0(*) 5.0(*) 5.0(*) VIC = VIH VI/O = VCC to GND II/O ≤ 1mA VIC = VIH VI/O = VCC or GND II/O ≤ 1mA VOS = VCC to GND VIS = VCC to GND VIC = VIL VOS = VCC to GND VIC = VIH 0 to 5.5 5.5 VIC = 5.5V or GND VI = VCC or GND 12 TA = 25°C Min. 2 0.8 17 Typ. Max. Value -40 to 85°C Min. 2 0.8 20 Max. -55 to 125°C Min. 2 0.8 24 Max. V V V Unit VIH VIL RON High Level Input Voltage Low Level Input Voltage ON Resistance RON ON Resistance 5.0(*) 10 14 18 20 V IOFF Input/Output Leakage Current (SWITCH OFF) Switch Input Leakage Current (SWITCH ON, OUTPUT OPEN) Control Input Leakage Current Quiescent Supply Current 5.5 ±0.1 ±1 ±1 µA IIZ 5.5 ±0.1 ±1 ±5 µA IIN ICC ± 0.1 1 ± 1.0 10 ± 1.0 20 µA µA (*) Voltage range is 5V ± 0.5V AC ELECTRICAL CHARACTERISTICS (CL = 50pF, Input tr = tf = 3ns) Test Condition Symbol Parameter VCC (V) 5.0 (*) Value TA = 25°C Min. Typ. 0.6 Max. 0.7 7.5 4.0 -40 to 85°C Min. Max. 1.0 9.0 5.0 -55 to 125°C Min. Max. 2.0 10.0 7.0 ns ns ns Unit tPD tPLZ tPHZ tPZL tPZH Delay Time Output Disable Time Output Enable Time 5.0(*) 5.0(*) RL = 500 Ω RL = 1 K Ω 6.0 2.5 (*) Voltage range is 5.0V ± 0.5V 3/9 74V2T66 CAPACITIVE CHARACTERISTICS Test Condition Symbol Parameter Min. CIN CI/O CPD Input Capacitance Output Capacitance Power Dissipation Capacitance (note 1) TA = 25°C Typ. 4 10 3 Max. 10 Value -40 to 85°C Min. Max. 10 -55 to 125°C Min. Max. 10 pF pF pF Unit 1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x fIN + ICC/2(per switch) ANALOG SWITCH CHARACTERISTICS (GND = 0V; TA = 25°C) Test Condition Symbol Parameter VCC (V) 5.0(*) 5.0(*) VIN (Vp-p) 4 fIN = 1 KHz RL = 10 KΩ, CL = 50 pF Adjust fIN voltage to obtain 0 dBm at VOS. Increase fIN Frequency until dB meter reads -3dB RL = 50Ω, CL = 10 pF VIN is centered at VCC/2 Adjust fIN Voltage to obtained 0dBm at VIS RL = 600Ω, CL = 50 pF, fIN = 1MHz sine wave RL = 600Ω, CL = 50 pF, fIN = 1MHz square wave tr=tf= 2.0ns RL = 600Ω, CL = 50 pF, fIN = 1MHz sine wave Value Unit Typ. 0.04 180 % MHz fMAX Sine Wave Distortion (THD) Frequency Response (Switch ON) Feedthrough Attenuation (Switch OFF) 5.0(*) -60 dB Crosstalk (Control 5.0(*) Input to Signal Output) Crosstalk Between 5.0(*) Switches (*) Voltage range is 5.0V ± 0.5V 60 mV -60 dB 4/9 74V2T66 SWITCHING CARACTERISTICS TEST CIRCUIT FEEDTHROUGH ATTENUATION BANDWIDTH ATTENUATION MAXIMUM CONTROL FREQUENCY CROSSTALK (control to output 5/9 74V2T66 CHANNEL RESISTANCE (RON) ICC (Opr.) 6/9 74V2T66 SOT23-8L MECHANICAL DATA mm. DIM. MIN. A A1 A2 b C D E E1 e e1 L 0.35 0.90 0.00 0.90 0.22 0.09 2.80 2.60 1.50 0 .65 1.95 0.55 13.7 TYP MAX. 1.45 0.15 1.30 0.38 0.20 3.00 3.00 1.75 MIN. 35.4 0.0 35.4 8.6 3.5 110.2 102.3 59.0 25.6 76.7 21.6 TYP. MAX. 57.1 5.9 51.2 14.9 7.8 118.1 118.1 68.8 mils 7/9 74V2T66 Tape & Reel SOT23-xL MECHANICAL DATA mm. DIM. MIN. A C D N T Ao Bo Ko Po P 3.13 3.07 1.27 3.9 3.9 3.23 3.17 1.37 4.0 4.0 12.8 20.2 60 14.4 3.33 3.27 1.47 4.1 4.1 0.123 0.120 0.050 0.153 0.153 0.127 0.124 0.054 0.157 0.157 13.0 TYP MAX. 180 13.2 0.504 0.795 2.362 0.567 0.131 0.128 0.0.58 0.161 0.161 0.512 MIN. TYP. MAX. 7.086 0.519 inch 8/9 74V2T66 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. © The ST logo is a registered trademark of STMicroelectronics © 2002 STMicroelectronics - Printed in Italy - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - Canada - China - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco Singapore - Spain - Sweden - Switzerland - United Kingdom - United States. © http://www.st.com 9/9