74V2T66STR

74V2T66 Dual bilateral switch Features ■ ■ ■ ■ ■ ■ High speed: – tPD = 0.6ns (Typ) at VCC = 5V Compatible with TTL level Low power consumpition – ICC = 1mA(Max.) at TA = 25°C Low "ON" resistance: – RON = 10Ω (Typ.) at VCC = 5V II/O = 1mA Sine wave distortion: – 0.04% at VCC = 5.0V, f = 1KHz Operating voltage range: – VCC (Opr) = 2.0V to 3.6V SOT23-8L Description The 74V2T66 is an advanced high-speed CMOS dual bilateral switch fabricated in silicon gate C2MOS technology. It achieves high speed propagation delay and very low on resistances while maintaining true CMOS low power consumption. This bilateral switch handles rail to rail analog and digital signals that may vary across the full power supply range (from GND to VCC) The C input is provided to control the switch and it’s compatible with standard CMOS output; the switch is ON (port I/O is connected to Port O/I) when the C input is held high and OFF (high impedance state exists between the two ports) when C is held low. It can be used in many application as Battery Powered System, Test Equipment. It’s available in the commercial and extended temperature range in SOT23-8L package. All inputs and output are equipped with protection circuits against static discharge, giving them ESD immunity and transient excess voltage. Order code Part number 74V2T66STR Package SOT23-8L Packing Tape and reel January 2007 Rev 4 1/14 www.st.com 14 Contents 74V2T66 Contents 1 2 Logic symbols and I/O equivalent circuit . . . . . . . . . . . . . . . . . . . . . . . . 3 Pin settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2.1 2.2 2.3 Pin connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Truth table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3 Maximum rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 3.1 Recommended operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 4 5 6 7 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Switching caracteristics test circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 2/14 74V2T66 Logic symbols and I/O equivalent circuit 1 Logic symbols and I/O equivalent circuit Figure 1. IEC logic symbols Figure 2. Input and output equivalent circuit 3/14 Pin settings 74V2T66 2 2.1 Pin settings Pin connection Figure 3. Pin connection (top through view) 2.2 Pin description Table 1. Pin description Pin N° 1, 5 2, 6 7, 3 4 8 Symbol 1I/O, 2I/O 1O/I, 2O/I 1C, 2C GND VCC Name and function Independent Input/Output Independent Output/Input Enable Input (Active HIGH) Ground (0V) Positive Supply Voltage 2.3 Truth table Table 2. Truth table Control H L 1. High impedance state Switch Function ON OFF (1) 4/14 74V2T66 Maximum rating 3 Maximum rating stressing the device above the rating listed in the “absolute maximum ratings” table may cause permanent damage to the device. these are stress ratings only and operation of the device at these or any other conditions above those indicated in the operating sections of this specification is not implied. exposure to absolute maximum rating conditions for extended periods may affect device reliability. refer also to the STMicroelectronics sure program and other relevant quality documents. Table 3. Absolute maximum ratings Symbol VCC VI VIC VO IIK IIK IOK IO ICC or IGND Tstg TL Supply voltage DC input voltage DC control input voltage DC output voltage DC input diode current DC control input diode current DC output diode current DC output current DC VCC or ground current Storage temperature Lead temperature (10 sec) Parameter Value -0.5 to +7.0 -0.5 to VCC + 0.5 -0.5 to +7.0 -0.5 to VCC + 0.5 ± 20 - 20 ± 20 ± 50 ± 50 -65 to +150 300 Unit V V V V mA mA mA mA mA °C °C 3.1 Recommended operating conditions Table 4. Recommended operating conditions Symbol VCC VI VIC VO Top dt/dv Supply voltage Input voltage Control input voltage Output voltage Operating temperature Input rise and fall time (1)VCC = 5.0V Parameter Value 4.5 to 5.5 0 to VCC 0 to 5.5 0 to VCC -55 to 125 0 to 20 Unit V V V V °C ns/V 1. VIN from 0.8V to 2V on control pin 5/14 Electrical characteristics 74V2T66 4 Electrical characteristics Table 5. DC characteristics Test condition Symbol Parameter VCC (V) 5.0(1) 5.0(1) VIC = VIH VI/O = VCC to 5.0(1) GND II/O ≤ 1mA VIC = VIH VI/O = VCC or 5.0(1) GND II/O ≤ 1mA VOS = VCC to GND VIS = VCC to GND VIC = VIL VOS = VCC to GND VIC = VIH VIC = 5.5V or GND VI = VCC or GND TA = 25°C Value -40 to 85°C -55 to 125°C Unit Min. Typ. Max. Min. Max. Min. Max. 2 0.8 2 0.8 2 0.8 V V VIH VIL High level input voltage Low level input voltage RON ON resistance 12 17 20 24 Ω RON ON resistance 10 14 18 20 Ω IOFF Input/output leakage current (SWITCH OFF) 5.5 ±0.1 ±1 ±1 µA IIZ Switch input leakage current (switch on, output open) Control input leakage current Quiescent supply current 5.5 0 to 5.5 5.5 ±0.1 ±1 ±5 µA IIN ICC ± 0.1 1 ± 1.0 10 ± 1.0 20 µA µA 1. Voltage range is 5V ± 0.5V Table 6. Test condition Symbol Parameter VCC (V) 5.0(1) 5.0(1) 5.0(1) RL = 500 Ω RL = 1 KΩ TA = 25°C Value -40 to 85°C -55 to 125°C Unit Min. Typ. Max. Min. Max. Min. Max. 0.6 6.0 0.7 7.5 1.0 9.0 2.0 10.0 ns ns tPD tPLZ tPHZ tPZL tPZH Delay time Output disable time Output enable time 2.5 4.0 5.0 7.0 ns 1. Voltage range is 5.0V ± 0.5V 6/14 74V2T66 Electrical characteristics Table 7. Capacitive characteristics Test condition Symbol Parameter Min. CIN CI/O CPD Input capacitance Output capacitance Power dissipation capacitance(1) TA = 25°C Typ. 4 10 3 Max. 10 Value -40 to 85°C Min. Max. 10 -55 to 125°C Min. Max. 10 pF pF pF Unit 1. CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x fIN + ICC/2(per switch) Table 8. Analog switch characteristics (GND = 0V; TA = 25°C) Test Condition Symbol Parameter VCC (V) 5.0(1) VIN (Vp-p) 4 fIN = 1 KHz RL = 10 KΩ, CL = 50 pF Value Unit Typ. Sine wave distortion (THD) Frequency Response (Switch ON) Feedthrough Attenuation (Switch OFF) Crosstalk (Control Input to Signal Output) Crosstalk Between Switches 1. Voltage range is 5.0V ± 0.5V 0.04 % fMAX Adjust fIN voltage to obtain 0 dBm at VOS. 5.0(1) Increase fIN Frequency until dB meter reads -3dB RL = 50Ω, CL = 10 pF VIN is centered at VCC/2 5.0(1) Adjust fIN Voltage to obtained 0dBm at VIS RL = 600Ω, CL = 50 pF, fIN = 1MHz sine wave 5.0(1) RL = 600Ω, CL = 50 pF, fIN = 1MHz square wave tr = tf = 2.0ns 180 MHz -60 dB 60 mV 5.0(1) RL = 600Ω, CL = 50 pF, fIN = 1MHz sine wave -60 dB 7/14 Switching caracteristics test circuit 74V2T66 5 Figure 4. Switching caracteristics test circuit Figure 5. Figure 6. Feedthrough attenuation Figure 7. Bandwidth attenuation Figure 8. CI-O, CI/O Figure 9. Maximum control frequency 8/14 74V2T66 Table 9. Crosstalk (control to output) Switching caracteristics test circuit Figure 10. Channel resistance (RON) Table 10. ICC (Opr.) 9/14 Package mechanical data 74V2T66 6 Package mechanical data In order to meet environmental requirements, ST offers these devices in ECOPACK® packages. These packages have a Lead-free second level interconnect . The category of second level interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an ST trademark. ECOPACK specifications are available at: www.st.com 10/14 74V2T66 Package mechanical data SOT23-8L MECHANICAL DATA mm. DIM. MIN. A A1 A2 b C D E E1 e e1 L 0.35 0.90 0.00 0.90 0.22 0.09 2.80 2.60 1.50 0 .65 1.95 0.55 13.7 TYP MAX. 1.45 0.15 1.30 0.38 0.20 3.00 3.00 1.75 MIN. 35.4 0.0 35.4 8.6 3.5 110.2 102.3 59.0 25.6 76.7 21.6 TYP. MAX. 57.1 5.9 51.2 14.9 7.8 118.1 118.1 68.8 mils 11/14 Package mechanical data 74V2T66 Tape & Reel SOT23-xL MECHANICAL DATA mm. DIM. MIN. A C D N T Ao Bo Ko Po P 3.13 3.07 1.27 3.9 3.9 3.23 3.17 1.37 4.0 4.0 12.8 20.2 60 14.4 3.33 3.27 1.47 4.1 4.1 0.123 0.120 0.050 0.153 0.153 0.127 0.124 0.054 0.157 0.157 13.0 TYP MAX. 180 13.2 0.504 0.795 2.362 0.567 0.131 0.128 0.0.58 0.161 0.161 0.512 MIN. TYP. MAX. 7.086 0.519 inch 12/14 74V2T66 Revision history 7 Revision history Table 11. Revision history Date 31-Jan-2007 Revision 4 Changes Document reformatted, Typo in RON value 13/14 74V2T66 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2007 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 14/14