74VHC02MTR

74VHC02 QUAD 2-INPUT NOR GATE s s s s s s s s s s HIGH SPEED: tPD = 3.6ns (TYP.) at VCC = 5V LOW POWER DISSIPATION: ICC = 2 µA (MAX.) at TA=25°C HIGH NOISE IMMUNITY: VNIH = VNIL = 28% VCC (MIN.) POWER DOWN PROTECTION ON INPUTS SYMMETRICAL OUTPUT IMPEDANCE: |IOH| = IOL = 8mA (MIN) BALANCED PROPAGATION DELAYS: tPLH ≅ tPHL OPERATING VOLTAGE RANGE: VCC(OPR) = 2V to 5.5V PIN AND FUNCTION COMPATIBLE WITH 74 SERIES 02 IMPROVED LATCH-UP IMMUNITY LOW NOISE: VOLP = 0.8V (MAX.) SOP TSSOP Table 1: Order Codes PACKAGE SOP TSSOP T&R 74VHC02MTR 74VHC02TTR DESCRIPTION The 74VHC02 is an advanced high-speed CMOS QUAD 2-INPUT NOR GATE fabricated with sub-micron silicon gate and double-layer metal wiring C2MOS technology. The internal circuit is composed of 3 stages including buffer output, which provides high noise immunity and stable output. Power down protection is provided on all inputs and 0 to 7V can be accepted on inputs with no regard to the supply voltage. This device can be used to interface 5V to 3V. All inputs and outputs are equipped with protection circuits against static discharge, giving them 2KV ESD immunity and transient excess voltage. Figure 1: Pin Connection And IEC Logic Symbols November 2004 Rev. 5 1/11 74VHC02 Figure 2: Input Equivalent Circuit Table 2: Pin Description PIN N° 2, 5, 8, 11 3, 6, 9, 12 1, 4, 10, 13 7 14 SYMBOL 1A to 4A 1B to 4B 1Y to 4Y GND VCC NAME AND FUNCTION Data Inputs Data Inputs Data Outputs Ground (0V) Positive Supply Voltage Table 3: Truth Table A L L H H B L H L H Y H L L L Table 4: Absolute Maximum Ratings Symbol VCC VI VO IIK IOK IO Supply Voltage DC Input Voltage DC Output Voltage DC Input Diode Current DC Output Diode Current DC Output Current Parameter Value -0.5 to +7.0 -0.5 to +7.0 -0.5 to VCC + 0.5 - 20 ± 20 ± 25 ± 50 -65 to +150 300 Unit V V V mA mA mA mA °C °C ICC or IGND DC VCC or Ground Current Tstg Storage Temperature TL Lead Temperature (10 sec) Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is not implied Table 5: Recommended Operating Conditions Symbol VCC VI VO Top dt/dv Supply Voltage Input Voltage Output Voltage Operating Temperature Input Rise and Fall Time (note 1) (VCC = 3.3 ± 0.3V) (VCC = 5.0 ± 0.5V) Parameter Value 2 to 5.5 0 to 5.5 0 to VCC -55 to 125 0 to 100 0 to 20 Unit V V V °C ns/V 1) VIN from 30% to 70% of VCC 2/11 74VHC02 Table 6: DC Specifications Test Condition Symbol Parameter VCC (V) 2.0 3.0 to 5.5 2.0 3.0 to 5.5 2.0 3.0 4.5 3.0 4.5 VOL Low Level Output Voltage 2.0 3.0 4.5 3.0 4.5 II ICC Input Leakage Current Quiescent Supply Current 0 to 5.5 5.5 IO=-50 µA IO=-50 µA IO=-50 µA IO=-4 mA IO=-8 mA IO=50 µA IO=50 µA IO=50 µA IO=4 mA IO=8 mA VI = 5.5V or GND VI = VCC or GND TA = 25°C Min. 1.5 0.7VCC 0.5 0.3VCC 1.9 2.9 4.4 2.58 3.94 0.0 0.0 0.0 0.1 0.1 0.1 0.36 0.36 ± 0.1 2 2.0 3.0 4.5 1.9 2.9 4.4 2.48 3.8 0.1 0.1 0.1 0.44 0.44 ±1 20 Typ. Max. Value -40 to 85°C Min. 1.5 0.7VCC 0.5 0.3VCC 1.9 2.9 4.4 2.4 3.7 0.1 0.1 0.1 0.55 0.55 ±1 20 µA µA V V Max. -55 to 125°C Min. 1.5 0.7VCC 0.5 0.3VCC V V Max. Unit VIH High Level Input Voltage Low Level Input Voltage High Level Output Voltage VIL VOH Table 7: AC Electrical Characteristics (Input tr = tf = 3ns) Test Condition Symbol Parameter VCC (V) 3.3(*) 3.3(*) 5.0 (**) Value TA = 25°C Min. Typ. 5.6 8.1 3.6 4.5 Max. 7.9 11.4 5.5 7.5 -40 to 85°C Min. 1.0 1.0 1.0 1.0 Max. 9.5 13.0 6.5 8.5 -55 to 125°C Min. 1.0 1.0 1.0 1.0 Max. 9.5 13.0 6.5 8.5 ns Unit CL (pF) 15 50 15 50 tPLH tPHL Propagation Delay Time 5.0(**) (*) Voltage range is 3.3V ± 0.3V (**) Voltage range is 5.0V ± 0.5V 3/11 74VHC02 Table 8: Capacitive Characteristics Test Condition Symbol Parameter TA = 25°C Min. CIN CPD Input Capacitance Power Dissipation Capacitance (note 1) Typ. 6 19 Max. 10 Value -40 to 85°C Min. Max. 10 -55 to 125°C Min. Max. 10 pF pF Unit 1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x fIN + ICC/4 (per gate) Table 9: Dynamic Switching Characteristics Test Condition Symbol Parameter VCC (V) 5.0 TA = 25°C Min. Typ. 0.3 -0.8 CL = 50 pF 3.5 -0.3 Max. 0.8 V Value -40 to 85°C Min. Max. -55 to 125°C Min. Max. Unit VOLP VOLV VIHD VILD Dynamic Low Voltage Quiet Output (note 1, 2) Dynamic High Voltage Input (note 1, 3) Dynamic Low Voltage Input (note 1, 3) 5.0 V 5.0 1.5 V 1) Worst case package. 2) Max number of outputs defined as (n). Data inputs are driven 0V to 5.0V, (n-1) outputs switching and one output at GND. 3) Max number of data inputs (n) switching. (n-1) switching 0V to 5.0V. Inputs under test switching: 5.0V to threshold (VILD), 0V to threshold (VIHD), f=1MHz. Figure 3: Test Circuit CL =15/ 50pF or equivalent (includes jig and probe capacitance) RT = ZOUT of pulse generator (typically 50Ω) 4/11 74VHC02 Figure 4: Waveform - Propagation Delays (f=1MHz; 50% duty cycle) 5/11 74VHC02 SO-14 MECHANICAL DATA DIM. A A1 A2 B C D E e H h L k ddd 5.8 0.25 0.4 0° mm. MIN. 1.35 0.1 1.10 0.33 0.19 8.55 3.8 1.27 6.2 0.50 1.27 8° 0.100 0.228 0.010 0.016 0° TYP MAX. 1.75 0.25 1.65 0.51 0.25 8.75 4.0 MIN. 0.053 0.004 0.043 0.013 0.007 0.337 0.150 0.050 0.244 0.020 0.050 8° 0.004 inch TYP. MAX. 0.069 0.010 0.065 0.020 0.010 0.344 0.157 0016019D 6/11 74VHC02 TSSOP14 MECHANICAL DATA mm. DIM. MIN. A A1 A2 b c D E E1 e K L 0˚ 0.45 0.60 0.05 0.8 0.19 0.09 4.9 6.2 4.3 5 6.4 4.4 0.65 BSC 8˚ 0.75 0˚ 0.018 0.024 1 TYP MAX. 1.2 0.15 1.05 0.30 0.20 5.1 6.6 4.48 0.002 0.031 0.007 0.004 0.193 0.244 0.169 0.197 0.252 0.173 0.0256 BSC 8˚ 0.030 0.004 0.039 MIN. TYP. MAX. 0.047 0.006 0.041 0.012 0.0089 0.201 0.260 0.176 inch A A2 A1 b e K c L E D E1 PIN 1 IDENTIFICATION 1 0080337D 7/11 74VHC02 Tape & Reel SO-14 MECHANICAL DATA mm. DIM. MIN. A C D N T Ao Bo Ko Po P 6.4 9 2.1 3.9 7.9 12.8 20.2 60 22.4 6.6 9.2 2.3 4.1 8.1 0.252 0.354 0.082 0.153 0.311 TYP MAX. 330 13.2 0.504 0.795 2.362 0.882 0.260 0.362 0.090 0.161 0.319 MIN. TYP. MAX. 12.992 0.519 inch 8/11 74VHC02 Tape & Reel TSSOP14 MECHANICAL DATA mm. DIM. MIN. A C D N T Ao Bo Ko Po P 6.7 5.3 1.6 3.9 7.9 12.8 20.2 60 22.4 6.9 5.5 1.8 4.1 8.1 0.264 0.209 0.063 0.153 0.311 TYP MAX. 330 13.2 0.504 0.795 2.362 0.882 0.272 0.217 0.071 0.161 0.319 MIN. TYP. MAX. 12.992 0.519 inch 9/11 74VHC02 Table 10: Revision History Date 12-Nov-2004 Revision 5 Description of Changes Order Codes Revision - pag. 1. 10/11 74VHC02 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics All other names are the property of their respective owners © 2004 STMicroelectronics - All Rights Reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 11/11