74VHCT126AM

® 74VHCT126A QUAD BUS BUFFERS (3-STATE) PRELIMINARY DATA s s s s s s s s s s HIGH SPEED: tPD = 5 ns (TYP.) at VCC = 5V LOW POWER DISSIPATION: ICC = 4 µA (MAX.) at TA = 25 oC COMPATIBLE WITH TTL OUTPUTS: VIH = 2V (MIN), VIL = 0.8V (MAX) POWER DOWN PROTECTION ON INPUTS & OUTPUTS SYMMETRICAL OUTPUT IMPEDANCE: |IOH| = IOL = 8 mA (MIN) BALANCED PROPAGATION DELAYS: tPLH ≅ tPHL OPERATING VOLTAGE RANGE: VCC (OPR) = 4.5V to 5.5V PIN AND FUNCTION COMPATIBLE WITH 74 SERIES 126 IMPROVED LATCH-UP IMMUNITY LOW NOISE: VOLP = 0.8V (Max.) SOP PACKAGE SOP TSSOP T UBE 74VHCT126AM TSSOP T&R 74VHCT126AMTR 74VHCT126ATTR ORDER CODES DESCRIPTION The 74VHCT126A is an advanced high-speed CMOS QUAD BUS BUFFERS fabricated with sub-micron silicon gate and double-layer metal wiring C2MOS technology. This device requires the 3-STATE control input G to be set low to place the output into the high impedance state. Power down protection is provided on all inputs and outputs and 0 to 7V can be accepted on inputs with no regard to the supply voltage. This device can be used to interface 5V to 3V. All inputs and outputs are equipped with protection circuits against static discharge, giving them 2KV ESD immunity and transient excess voltage. PIN CONNECTION AND IEC LOGIC SYMBOLS March 2000 1/8 74VHCT126A INPUT EQUIVALENT CIRCUIT PIN DESCRIPTION PIN No 1, 4, 10, 13 2, 5, 9, 12 3, 6, 8, 11 7 14 SYMBOL 1G to 4G 1A to 4A 1Y to 4Y GND VCC NAME AND FUNCT ION Output Enable Inputs Data Inputs Data Outputs Ground (0V) Positive Supply Voltage TRUTH TABLE A X L H X:”H” or ”L” Z: High Impedance G L H H Y Z L H ABSOLUTE MAXIMUM RATINGS Symbol VCC VI VO VO IIK IOK IO Tstg TL Supply Voltage DC Input Voltage DC Output Voltage (see note 1) DC Output Voltage (see note 2) DC Input Diode Current DC Output Diode Current DC Output Current Storage Temperature Lead Temperature (10 sec) Parameter Value -0.5 to +7.0 -0.5 to +7.0 -0.5 to +7.0 -0.5 to VCC + 0.5 - 20 ± 20 ± 25 ± 50 -65 to +150 300 Unit V V V V mA mA mA mA o o ICC or IGND DC VCC or Ground Current C C Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these condition is not implied. 1) Output in OFF State 2) High or Low State RECOMMENDED OPERATING CONDITIONS Symbol VCC VI VO VO Top dt/dv Supply Voltage Input Voltage Output Voltage (see note 1) Output Voltage (see note 2) Operating Temperature Input Rise and Fall Time (see note 3) (V CC = 5.0 ± 0.5V) Parameter Valu e 4.5 to 5.5 0 to 5.5 0 to 5.5 0 to VCC -40 to +85 0 to 20 Unit V V V V o C ns/V 1) Output in OFF State 2) High or Low State 3)VIN from0.8V to 2 V 2/8 74VHCT126A DC SPECIFICATIONS Symb ol Parameter T est Cond ition s V CC (V) VIH VIL VOH VOL IOZ High Level Input Voltage Low Level Input Voltage High Level Output Voltage Low Level Output Voltage High Impedance Output Leakage Current Input Leakage Current Quiescent Supply Current Additional Worst Case Supply Current Output Leakage Current 4.5 to 5.5 4.5 to 5.5 4.5 4.5 4.5 4.5 4.5 to 5.5 I O =-50 µ A IO=-8 mA I O=50 µ A IO=8 mA VI = VIH or VIL VO = 0V to 5.5V VI = 5.5V or GND VI = VCC or GND One Input at 3.4V, other input at VCC or GND VOUT = 5.5V 4.4 3.94 0.0 0.1 0.36 ±0.25 4.5 Min. 2 0.8 4.4 3.8 0.1 0.44 ±2.5 Typ . Value T A = 25 o C Max. -40 to 85 o C Min . 2 0.8 Max. V V Un it V V µA II ICC ∆ICC 0 to 5.5 5.5 5.5 ±0.1 4 1.35 ±1.0 40 1.5 µA µA mA IOPD 0 0.5 5.0 µA AC ELECTRICAL CHARACTERISTICS (Input t r = tf =3 ns) Symb ol Parameter V CC (V) tPLH tPHL tPZL tPZH tPLZ tPHZ Propagation Delay Time Output Enable Time Output Disable Time 5.0 Test Co ndition CL (pF ) 15 50 15 50 50 RL = 1KΩ RL = 1KΩ RL = 1KΩ Value T A = 25 o C Min. Typ . Max. 3.8 5.5 5.3 3.6 5.1 6.1 7.5 5.1 7.1 8.8 Un it -40 to 85 o C Min . Max. 1.0 6.5 1.0 1.0 1.0 1.0 8.5 6.0 8.0 10.0 5.0(*) (*) ns ns ns 5.0(*) 5.0(*) 5.0(*) (*) Voltage range is 5.0V ± 0.5V 3/8 74VHCT126A CAPACITIVE CHARACTERISTICS Symb ol Parameter Test Co nditions Min. C IN COUT CPD Input Capacitance Output Capacitance Power Dissipation Capacitance (note 1) T yp. 4 10 14 Valu e T A = 25 oC Max. 10 -40 to 85 o C Min. Max. 10 pF pF pF Un it 1) CPD isdefined as the value of the IC’sinternal equivalent capacitance which is calculated fromthe operating current consumption without load. (Referto Test Circuit).Average operting current can be obtained by the following equation. ICC(opr) = CPD • VCC • fIN + ICC/4(per circuit) DYNAMIC SWITCHING CHARACTERISTICS Symb ol Parameter T est Cond ition s V CC (V) VOLP VOLV VIHD VILD Dynamic Low Voltage Quiet Output (note 1, 2) Dynamic High Voltage Input (note 1, 3) Dynamic Low Voltage Input (note 1, 3) 5.0 -0.8 5.0 5.0 C L = 50 pF 2.0 0.8 Min. Typ . 0.3 -0.3 V Value T A = 25 o C Max. 0.8 -40 to 85 o C Min . Max. Un it 1) Worst case package. 2) Max number of outputs defined as (n). Data inputs are driven 0V to 5.0V, (n -1) outputs switching and one output at GND. 3) Max number of data inputs (n) switching. (n-1) switching 0V to5.0V. Inputs under test switching: 5.0V to threshold (VILD), 0V to threshold (VIHD), f=1MHz. TEST CIRCUIT T EST tPLH , tPHL tPZL , tPLZ tPZH , tPHZ CL = 15/50 pF or equivalent (includes jig and probe capacitance) RL = R1 = 1KΩ orequivalent RT = ZOUT of pulse generator (typically 50Ω) SW IT CH Open VCC GND 4/8 74VHCT126A WAVEFORM 1: PROPAGATION DELAYS (f=1MHz; 50% duty cycle) WAVEFORM 2: OUTPUT ENABLE AND DISABLE TIME (f=1MHz; 50% duty cycle) 5/8 74VHCT126A SO-14 MECHANICAL DATA DIM. MIN. A a1 a2 b b1 C c1 D E e e3 F G L M S 3.8 4.6 0.5 8.55 5.8 1.27 7.62 4.0 5.3 1.27 0.68 8 (max.) 0.149 0.181 0.019 8.75 6.2 0.35 0.19 0.5 45 (typ.) 0.336 0.228 0.050 0.300 0.157 0.208 0.050 0.026 0.344 0.244 0.1 mm TYP. MAX. 1.75 0.2 1.65 0.46 0.25 0.013 0.007 0.019 0.003 MIN. inch TYP. MAX. 0.068 0.007 0.064 0.018 0.010 P013G 6/8 74VHCT126A TSSOP14 MECHANICAL DATA mm MIN. A A1 A2 b c D E E1 e K L 0o 0.50 0.05 0.85 0.19 0.09 4.9 6.25 4.3 5 6.4 4.4 0.65 BSC 4o 0.60 8o 0.70 0o 0.020 0.10 0.9 TYP. MAX. 1.1 0.15 0.95 0.30 0.20 5.1 6.5 4.48 0.002 0.335 0.0075 0.0035 0.193 0.246 0.169 0.197 0.252 0.173 0.0256 BSC 4o 0.024 8o 0.028 0.004 0.354 MIN. inch TYP. MAX. 0.433 0.006 0.374 0.0118 0.0079 0.201 0.256 0.176 DIM. A A2 A1 b e K c L E D E1 PIN 1 IDENTIFICATION 1 7/8 74VHCT126A Information furnished is believed to be accurate and reliable. However, STMicroelectronic s assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specification mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems withoutexpress written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics © 2000 STMicroelectronics – Printed in Italy – All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - China - Finland - France - Germany - Hong Kong - India - Italy - Japan - Malaysia - Malta - Morocco Singapore - Spain - Sweden - Switzerland - United Kingdom - U.S.A. http://www.st.com . 8/8