ACST8

ACST8 Overvoltage protected AC switch Features ■ ■ ■ OUT Triac with overvoltage protection High noise immunity: static dV/dt > 2000 V/µs TO-220FPAB insulated package: 1500 V rms G OUT COM G OUT COM Benefits ■ ■ ■ ■ ■ Enables equipment to meet IEC 61000-4-5 High off-state reliability with planar technology Needs no external overvoltage protection Reduces the power passive component count High immunity against fast transients described in IEC 61000-4-4 standards TO-220AB ACST830-8T OUT TO-220FPAB ACST830-8FP G COM Applications ■ ■ D²PAK ACST830-8G AC mains static switching in appliance and industrial control systems Drive of medium power AC loads such as: – Universal motor of washing machine drum – Compressor for fridge or air conditioner Figure 1. Functional diagram OUT Description The ACST8 series belongs to the ACS™/ ACST power switch family built around A.S.D.® (application specific discrete) technology. This high performance device is suited to home appliances or industrial systems and drives an induction motor up to 8 A. This ACST8 device embeds a Triac structure with a high voltage clamping device to absorb the inductive turn off energy and withstand line transients such as those described in the IEC 61000-4-5 standards. ACST8 shows a high noise immunity complying with IEC standards such as IEC 61000-4-4 (fast transient burst test). G COM Table 1. Symbol IT(RMS) Device summary Value 8 800 30 Unit A V mA VDRM/VRRM IGT TM: ACS is a trademark of STMicroelectronics. ®: A.S.D. is a registered trademark of STMicroelectronics December 2009 Doc ID 7463 Rev 7 1/13 www.st.com 13 Characteristics ACST8 1 Table 2. Symbol Characteristics Absolute ratings (limiting values) Parameter TO-220FPAB IT(RMS) On-state rms current (full sine wave) TO-220AB / D2PAK D2PAK with 1 cm2 Cu ITSM I 2t dI/dt VPP (1) PG(AV) PGM IGM Tstg Tj Tl Non repetitive surge peak on-state current Tj initial = 25 °C, full cycle sine wave Thermal constraint for fuse selection Non repetitive on-state current critical rate of rise IG = 10 mA (tr < 100 ns) Non repetitive line peak pulse voltage Average gate power dissipation Peak gate power dissipation (tp = 20 ms) Peak gate current (tp = 20 ms) Storage temperature range Operating junction temperature range Maximum lead soldering temperature during 10 s TO-220FPAB F = 50 Hz F = 60 Hz Tcase = 91 °C 8 Tcase = 105 °C Tamb = 43 °C tp = 20 ms tp = 16.7 ms tp = 10 ms Rate period > 1 mn Tj = 25 °C Tj = 125 °C Tj = 125 °C Tj = 125 °C 2 80 84 42 100 2 0.1 10 1.6 - 40 to + 150 - 40 to + 125 260 1500 A A A A2s A/µs kV W W A °C °C °C V A Value Unit VINS(RMS) Insulation rms voltage 1. According to test described in IEC 61000-4-5 standard and Figure 18. Table 3. Symbol IGT(1) VGT VGD IH (2) Electrical characteristics per switch Test conditions VOUT = 12 V, RL = 33 Ω VOUT = 12V, RL = 33 Ω VOUT = VDRM, RL = 3.3 kΩ IOUT = 500 mA IG = 1.2 x IGT (2) (2) Quadrant Tj 25 °C 25 °C 125 °C 25 °C Max Max Min Max Max Min Min Min Value 30 1.0 0.2 30 50 2000 8 850 Unit mA V V mA mA V/µs A/ms V I - II - III I - II - III I - II - III IL dV/dt I - II - III 25 °C 125 °C 125 °C 25 °C VOUT = 67% VDRM, gate open Without snubber ICL = 0.1 mA, tp = 1 ms (dI/dt)c VCL 1. Minimum IGT is guaranteed at 5% of IGT(Max) 2. For either positive or negative polarity of OUT pin with reference to COM pin 2/13 Doc ID 7463 Rev 7 ACST8 Table 4. Symbol VTM VTO RD IDRM IRRM ITM = 11.3 A tp = 500 µs Threshold voltage Dynamic resistance VOUT = VDRM / VRRM Characteristics Static characteristics Test conditions Tj = 25 °C Tj = 125 °C Tj = 125 °C Tj = 25 °C Max Tj = 125 °C 1 mA Max Max Max Value 1.5 0.9 50 20 Unit V V mΩ µA Table 5. Symbol Thermal resistances Parameter Junction to ambient TO-220FPAB TO-220AB D2PAK TO-220FPAB Value 60 45 3.6 2 °C/W Unit Rth(j-a) Junction to ambient (soldered on 1 cm2 copper pad) Rth(j-c) Junction to case (AC) TO-220AB, D2PAK Figure 2. Maximum power dissipation versus Figure 3. on-state rms current IT(RMS)(A) 9 8 7 6 5 4 α=180° On-state rms current versus case temperature (full cycle) P(W) 10 9 8 7 6 5 4 3 2 1 0 0 1 2 3 4 5 6 7 8 180° α=180 ° TO-220AB D2PACK TO-220FPAB 3 2 IT(RMS)(A) 1 0 0 25 TC(°C) 50 75 100 125 Doc ID 7463 Rev 7 3/13 Characteristics ACST8 Figure 4. On-state rms current versus ambient temperature (free air convection, fulle cycle) Figure 5. Relative variation of thermal impedance versus pulse duration IT(RMS)(A) 3.0 α=180° D2PAK Copper surface = 1cm2 K=[Zth/Rth] 1.0E+00 TO-220AB Zth(j-c) Zth(j-a) TO-220FPAB 2.5 2.0 TO-220 1.5 1.0 0.5 1.0E-01 TO-220AB TO-220FPAB Tamb(°C) 0.0 0 25 50 75 100 125 tp(s) 1.0E-02 1.0E-03 1.0E-02 1.0E-01 1.0E+00 1.0E+01 1.0E+02 1.0E+03 Figure 6. Relative variation of gate trigger current (IGT) and voltage (VGT) versus junction temperature Figure 7. Relative variation of holding current (IH) and latching current (IL) versus junction temperature 3.0 2.5 IGT, VGT[T j] / IGT, VGT[T j=25 °C] 2.5 IGT Q3 IH, IL [T j] / IH, IL [T j=25 °C] Typical values IGT Q1-Q2 2.0 2.0 1.5 1.5 1.0 1.0 0.5 VGT Q1-Q2-Q3 IL 0.5 Tj(°C) 0.0 -50 -25 0 25 50 75 100 125 0.0 -50 -25 0 25 Tj(°C) 50 75 IH 100 125 Figure 8. Surge peak on-state current versus Figure 9. number of cycles Non repetitive surge peak on-state current and corresponding value of I2t versus sinusoidal pulse width 90 80 70 60 50 40 30 20 10 0 ITSM(A) ITSM(A), I²t (A²s) 1000 Tj initial=25 °C t=20ms dI/dt limitation: 100 A/µs ITSM Non repetitive Tj initial=25 °C One cycle 100 I²t Repetitive TC=105 °C 10 Number of cycles 1 10 100 1000 sinusoidal pulse with width tP < 10 ms tP(ms) 0.10 1.00 10.00 1 0.01 4/13 Doc ID 7463 Rev 7 ACST8 Characteristics Figure 10. On-state characteristics (maximum Figure 11. Relative variation of critical rate of values) decrease of main current (dI/dt)c versus junction temperature ITM (A) 100 (dI/dt)c[Tj] / (dI/dt)c[Tj=125°C] 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 5 10 Tj=125 °C Tj=25 °C VTM (V) 2 3 4 Tj max : Vto = 0.90 V Rd = 50 mΩ Tj(°C) 25 50 75 100 125 1 0 1 Figure 12. Relative variation of static dV/dt immunity versus junction temperature (gate open) dV/dt[Tj] / dV/dt[Tj=125°C] 11 10 9 8 7 6 5 4 3 2 1 0 25 50 75 100 125 VD=VR=530 V Figure 13. Relative variation of leakage current versus junction temperature 1.0E+00 IDRM/IRRM [Tj;V DRM/ VRRM]/IDRM/IRRM [Tj=125°C; 8 00V] VDRM=VRRM=800 V Different blocking voltages 1.0E-01 VDRM=VRRM=600 V 1.0E-02 VDRM=VRRM=200 V Tj(°C) 1.0E-03 25 50 75 Tj(°C) 100 125 Figure 14. Relative variation of clamping voltage (VCL) versus junction temperature (minimum values) VCL [Tjj/VCL[Tj=25°C] 1.15 Figure 15. Thermal resistance junction to ambient versus copper surface under tab 80 70 Rth(j-a) (°C/W) Printed circuit board FR4, copper thickness = 35 µm D²PAK 1.10 60 1.05 50 40 30 20 1.00 0.95 0.90 Tj (°C) 0.85 -50 -25 0 25 50 75 100 125 10 SCU(cm²) 0 0 5 10 15 20 25 30 35 40 Doc ID 7463 Rev 7 5/13 Application information ACST8 2 2.1 Application information Typical application description The ACST8 device has been designed to control medium power load, such as AC motors in home appliances. Thanks to its thermal and turn off commutation performances, the ACST8 switch is able to drive an inductive load up to 8 A with no turn off additional snubber. It also provides high thermal performances in static and transient modes such as high torque operating conditions or inrush current of an AC motor. Figure 16. AC induction motor control – typical diagram AC Motor AC induction motor AC Mains C L Phase shift capacitor + protective air inductance ACST Rg Rg Selection of the rotor direction ACST Vcc MCU 6/13 Doc ID 7463 Rev 7 ACST8 Application information 2.2 AC line transient voltage ruggedness In comparison with standard Triacs, which are not robust against surge voltage, the ACST8 is self-protected against over-voltage, specified by the new parameter VCL. The ACST8 switch can safely withstand AC line transient voltages either by clamping the low energy spikes, such as inductive spikes at switch off, or by switching to the on state (for less than 10 ms) to dissipate higher energy shocks through the load. This safety feature works even with high turn-on current ramp up. The test circuit of Figure 17 represents the ACST8 application, and is used to stress the ACST switch according to the IEC 61000-4-5 standard conditions. With the additional effect of the load which is limiting the current, the ACST switch withstands the voltage spikes up to 2 kV on top of the peak line voltage. The protection is based on an overvoltage crowbar technology. The ACST8 folds back safely to the on state as shown in Figure 18. The ACST8 recovers its blocking voltage capability after the surge and the next zero current crossing. Such a non repetitive test can be done at least 10 times on each AC line voltage polarity. Figure 17. Overvoltage ruggedness test circuit for resistive and inductive loads for IEC 61000-4-5 standards R = 13 Ω, L = 2 µH, Vsurge = 2 kV Rg = 82 Ω Surge generator 2kV surge Rgene Filtering unit Model of the load R L ACST8 AC Mains Rg Doc ID 7463 Rev 7 7/13 Ordering information scheme Figure 18. Typical current and voltage waveforms across the ACST8 during IEC 61000-4-5 standard test Vpeak = VCL 1.2/50 µs voltage surge ACST8 V 0 Ipeak = 160 A I 8/20 µs current surge 0 dI/dt = 180 A/µs 3 Ordering information scheme Figure 19. Ordering information scheme ACS T 8 30 - 8 AC switch Topology T = Triac On-state rms current 8=8A Triggering gate current 30 = 30 mA Repetitive peak off-state voltage 8 = 800 V Package FP = TO-220FPAB T = TO-220AB G = D2PAK Delivery mode TR = Tape and reel Blank = Tube FP TR 8/13 Doc ID 7463 Rev 7 ACST8 Package information 4 Package information ● ● Epoxy meets UL94, V0 Recommended torque: 0.4 to 0.6 N·m In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance. ECOPACK® specifications, grade definitions and product status are available at: www.st.com. ECOPACK® is an ST trademark. Table 6. TO-220AB dimensions Dimensions Ref. Millimeters Min. A C H2 Dia L5 L7 L6 L2 F2 F1 L9 L4 F G1 G M E D C A Inches Min. 0.173 0.048 0.094 0.019 0.024 0.044 0.044 0.194 0.094 0.393 Max. 0.181 0.051 0.107 0.027 0.034 0.066 0.066 0.202 0.106 0.409 Max. 4.60 1.32 2.72 0.70 0.88 1.70 1.70 5.15 2.70 10.40 4.40 1.23 2.40 0.49 0.61 1.14 1.14 4.95 2.40 10 D E F F1 F2 G G1 H2 L2 L4 L5 L6 L7 L9 M Diam. 16.4 typ. 13 2.65 15.25 6.20 3.50 14 2.95 15.75 6.60 3.93 0.645 typ. 0.511 0.104 0.600 0.244 0.137 0.551 0.116 0.620 0.259 0.154 2.6 typ. 3.75 3.85 0.102 typ. 0.147 0.151 Doc ID 7463 Rev 7 9/13 Package information Table 7. TO-220FPAB dimensions Dimensions Ref. Millimeters Min. A B A H B ACST8 Inches Min. 0.173 0.098 0.098 0.018 0.030 0.045 0.045 0.195 0.094 0.393 Max. 0.181 0.106 0.108 0.027 0.039 0.067 0.067 0.205 0.106 0.409 Max. 4.6 2.7 2.75 0.70 1 1.70 1.70 5.20 2.7 10.4 4.4 2.5 2.5 0.45 0.75 1.15 1.15 4.95 2.4 10 D E Dia L6 L2 L3 L5 F1 L4 F2 D L7 F F1 F2 G G1 H L2 E 16 Typ. 28.6 9.8 2.9 15.9 9.00 3.00 30.6 10.6 3.6 16.4 9.30 3.20 0.63 Typ. 1.126 0.386 0.114 0.626 0.354 0.118 1.205 0.417 0.142 0.646 0.366 0.126 F G1 G L3 L4 L5 L6 L7 Diam. 10/13 Doc ID 7463 Rev 7 ACST8 Table 8. D2PAK dimensions Package information Dimensions Ref. Millimeters Min. A A E L2 Inches Min. 0.173 0.098 0.001 0.027 0.045 0.017 0.048 0.352 0.393 0.192 0.590 0.050 0.055 0.094 Max. 0.181 0.106 0.009 0.037 0.067 0.024 0.054 0.368 0.409 0.208 0.624 0.055 0.069 0.126 Max. 4.60 2.69 0.23 0.93 1.70 0.60 1.36 9.35 10.40 5.28 15.85 1.40 1.75 3.20 4.40 2.49 0.03 0.70 1.14 0.45 1.23 8.95 10.00 4.88 15.00 1.27 1.40 2.40 A1 C2 A2 B D L L3 A1 B2 B G A2 R B2 C C2 C D E G L M * V2 L2 L3 * FLAT ZONE NO LESS THAN 2mm M R V2 0.40 typ. 0° 8° 0.016 typ. 0° 8° Figure 20. Footprint (dimensions in mm) 16.90 10.30 1.30 5.08 8.90 3.70 Doc ID 7463 Rev 7 11/13 Ordering information ACST8 5 Ordering information Table 9. Ordering information Marking Package TO-220FPAB ACST8308 TO-220AB D2PAK Weight 2.4 g 2.3 g 1.5 g Base qty 50 50 500 Packing mode Tube Tube Tape and reel Order code ACST830-8FP ACST830-8T ACST830-8GTR 6 Revision history Table 10. Date Jan-2002 08-Nov-2004 24-Nov-2004 18-Dec-2009 Document revision history Revision 4B 5 6 7 Last update. TO-220AB and D2PAK packages added. Table 6 page 3: IGT parameter added Added ECOPACK statement. Reformatted for consistency with other datasheets in this product class. Order codes updated. Changes 12/13 Doc ID 7463 Rev 7 ACST8 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2009 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com Doc ID 7463 Rev 7 13/13