B7NK80Z-1

STP7NK80Z - STP7NK80ZFP STB7NK80Z - STB7NK80Z-1 N-channel 800V - 1.5Ω - 5.2A - TO-220/TO-220FP/D2PAK/I2PAK Zener-protected SuperMESH™ Power MOSFET General features Type STP7NK80Z STP7NK80ZFP STB7NK80Z STB7NK80Z-1 ■ ■ ■ ■ ■ VDSS (@Tjmax) 800V 800V 800V 800V RDS(on) < 1.8Ω < 1.8Ω < 1.8Ω < 1.8Ω ID 5.2A 5.2A 5.2A 5.2A 1 2 3 TO-220 TO-220FP Extremely high dv/dt capability 100% avalange tested Gate charge minimized Very low intrinsic capacitances Very good manufacturing repeatibility 1 3 3 12 D2PAK I2PAK Description The SuperMESH™ series is obtained through an extreme optimization of ST’s well established strip-based PowerMESH™ layout. In addition to pushing on-resistance significantly down, special care is taken to ensure a very good dv/dt capability for the most demanding applications. Such series complements ST full range of high voltage Power MOSFETs including revolutionary MDmesh™ products. Internal schematic diagram Applications ■ Switching application Order codes Part number STP7NK80Z STP7NK80ZFP STB7NK80ZT4 STB7NK80Z-1 Marking P7NK80Z P7NK80ZFP B7NK80Z B7NK80Z-1 Package TO-220 TO-220FP D²PAK I²PAK Packaging Tube Tube Tape e reel Tube October 2006 Rev 5 1/18 www.st.com 18 Contents STP7NK80Z - STP7NK80ZFP - STB7NK80Z - STB7NK80Z-1 Contents 1 2 Electrical ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2.1 Electrical characteristics (curves) ............................. 7 3 4 5 6 Test circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Packaging mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 2/18 STP7NK80Z - STP7NK80ZFP - STB7NK80Z - STB7NK80Z-1 Electrical ratings 1 Electrical ratings Table 1. Symbol Absolute maximum ratings Value Parameter TO-220 / D²PAK I²PAK 800 ± 30 5.2 3.3 20.8 125 1 4000 4.5 -2500 5.2 3.3 (1) (1) Unit TO-220FP V V A A A W W/°C V V/ns V °C °C VDS VGS ID ID IDM (2) Drain-source voltage (VGS = 0) Gate- source voltage Drain current (continuous) at TC = 25°C Drain current (continuous) at TC = 100°C Drain current (pulsed) Total dissipation at TC = 25°C Derating factor 20.8(1) 30 0.24 PTOT VESD(G-S) Gate source ESD(HBM-C=100pF, R=1.5KΩ) dv/dt (3) Peak diode recovery voltage slope Insulation withstand voltage (RMS) from all three leads to external heat sink (t=1s; Tc= 25°C) Max operating junction temperature Storage temperature VISO Tj Tstg -55 to 150 1. Limited only by maximum temperature allowed 2. Pulse width limited by safe operating area 3. ISD ≤5.2 A, di/dt ≤200A/µs, VDD ≤V(BR)DSS, Tj ≤TJMAX. Table 2. Thermal data Value Symbol Parameter TO-220/D2PAK I2PAK Unit TO-220FP 4.2 °C/W °C/W °C Rthj-case Rthj-amb Tl Thermal resistance junction-case max Thermal resistance junction-ambient max Maximum lead temperature for soldering purpose 1 62.5 300 3/18 Electrical ratings STP7NK80Z - STP7NK80ZFP - STB7NK80Z - STB7NK80Z-1 Table 3. Symbol IAR EAS Avalanche characteristics Parameter Avalanche current, repetitive or not-repetitive (pulse width limited by Tj Max) Single pulse avalanche energy (starting Tj=25°C, Id=Iar, Vdd=50V) Value 5.2 210 Unit A mJ 4/18 STP7NK80Z - STP7NK80ZFP - STB7NK80Z - STB7NK80Z-1 Electrical characteristics 2 Electrical characteristics (TCASE=25°C unless otherwise specified) Table 4. Symbol V(BR)DSS IDSS IGSS VGS(th) RDS(on) On/off states Parameter Drain-source Breakdown voltage Zero gate voltage Drain Current (VGS = 0) Gate-body leakage Current (VDS = 0) Gate threshold voltage Static drain-source on resistance Test conditions ID =1MA, VGS = 0 VDS = Max rating VDS = Max rating, TC = 125°C VGS = ± 20 V VDS = VGS, ID = 100 µA VGS = 10 V, ID = 2.6 A 3 3.75 1.5 Min. 800 1 50 ± 10 4.5 1.8 Typ. Max. Unit V µA µA µA V Ω Table 5. Symbol gfs (1) Ciss Coss Crss Coss eq. (2) Dynamic Parameter Test conditions Min. Typ. 5 1138 122 25 50 20 12 45 20 40 7 21 12 10 20 56 Max. Unit S pF pF pF pF ns ns ns ns nC nC nC ns ns ns Forward transconductance VDS = 15v, ID = 2.6 A Input capacitance Output capacitance Reverse transfer capacitance Equivalent output capacitance Turn-on delay time Rise time Turn-off delay time Fall time Total gate charge Gate-source charge Gate-drain charge Off-voltage rise time Fall time Cross-over time VDS = 25 V, f = 1 MHz, VGS = 0 VDS =0V, VDS = 0V to 640V td(on) tr tr(off) tr Qg Qgs Qgd tr(Voff) tr tc VDD = 400 V, ID = 2.6 A, RG = 4.7 Ω, VGS = 10 V (see Figure 16) VDD = 640 V, ID = 5.2 A, VGS = 10 V (see Figure 17) VDD = 640 V, ID = 5.2 A, RG = 4.7 Ω, VGS = 10 V (see Figure 16) 1. Pulsed: pulse duration=300µs, duty cycle 1.5% 2. Coss eq. is defined as a constant equivalent capacitance giving the same charging time as Coss when VDS increases from 0 to 80% VDSS. 5/18 Electrical characteristics STP7NK80Z - STP7NK80ZFP - STB7NK80Z - STB7NK80Z-1 Table 6. Symbol ISD ISDM(1) VSD(2) trr Qrr IRRM Source drain diode Parameter Source-drain current Source-drain current (pulsed) Forward on voltage Reverse recovery time Reverse recovery charge Reverse recovery current ISD = 5.2 A, VGS = 0 ISD = 5.2 A, di/dt = 100 A/µs VDD = 50 V, Tj = 150°C (see Figure 21) 530 3.31 12.5 Test conditions Min. Typ. Max. 5.2 20.8 1.6 Unit A A V ns µC A 1. Pulsed: pulse duration=300µs, duty cycle 1.5% 2. Pulse width limited by safe operating area Table 7. Symbol Gate-source zener diode Parameter Test conditions Min. 30 Typ. Max. Unit V BVGSO (1) Gate-source breakdown voltage Igs=± 1mA (Open Drain) 1. The built-in back-to-back Zener diodes have specifically been designed to enhance not only the device’s ESD capability, but also to make them safely absorb possible voltage transients that may occasionally be applied from gate to source. In this respect the Zener voltage is appropriate to achieve an efficient and cost-effective intervention to protect the device’s integrity. These integrated Zener diodes thus avoid the usage of external components. 6/18 STP7NK80Z - STP7NK80ZFP - STB7NK80Z - STB7NK80Z-1 Electrical characteristics 2.1 Figure 1. Electrical characteristics (curves) Safe operating area for TO-220/ D2PAK/I2PAK Figure 2. Thermal impedance for TO-220/ D2PAK/I2PAK Figure 3. Safe operating area for TO-220FP Figure 4. Thermal impedance for TO-220FP Figure 5. Output characterisics Figure 6. Transfer characteristics 7/18 Electrical characteristics Figure 7. Transconductance STP7NK80Z - STP7NK80ZFP - STB7NK80Z - STB7NK80Z-1 Figure 8. Static drain-source on resistance Figure 9. Gate charge vs gate-source voltage Figure 10. Capacitance variations Figure 11. Normalized gate threshold voltage vs temperature Figure 12. Normalized on resistance vs temperature 8/18 STP7NK80Z - STP7NK80ZFP - STB7NK80Z - STB7NK80Z-1 Figure 13. Source-drain diode forward characteristic Electrical characteristics Figure 14. Normalized BVDSS vs temperature Figure 15. Maximum avalanche energy vs temperature 9/18 Test circuit STP7NK80Z - STP7NK80ZFP - STB7NK80Z - STB7NK80Z-1 3 Test circuit Figure 17. Gate charge test circuit Figure 16. Switching times test circuit for resistive load Figure 18. Test circuit for inductive load Figure 19. Unclamped Inductive load test switching and diode recovery times circuit Figure 20. Unclamped inductive waveform Figure 21. Switching time waveform 10/18 STP7NK80Z - STP7NK80ZFP - STB7NK80Z - STB7NK80Z-1 Package mechanical data 4 Package mechanical data In order to meet environmental requirements, ST offers these devices in ECOPACK® packages. These packages have a Lead-free second level interconnect . The category of second level interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an ST trademark. ECOPACK specifications are available at: www.st.com 11/18 Package mechanical data STP7NK80Z - STP7NK80ZFP - STB7NK80Z - STB7NK80Z-1 TO-220 MECHANICAL DATA DIM. A b b1 c D E e e1 F H1 J1 L L1 L20 L30 mm. MIN. 4.40 0.61 1.15 0.49 15.25 10 2.40 4.95 1.23 6.20 2.40 13 3.50 16.40 28.90 3.75 2.65 3.85 2.95 0.147 0.104 TYP MAX. 4.60 0.88 1.70 0.70 15.75 10.40 2.70 5.15 1.32 6.60 2.72 14 3.93 MIN. 0.173 0.024 0.045 0.019 0.60 0.393 0.094 0.194 0.048 0.244 0.094 0.511 0.137 0.645 1.137 0.151 0.116 inch TYP. MAX. 0.181 0.034 0.066 0.027 0.620 0.409 0.106 0.202 0.052 0.256 0.107 0.551 0.154 øP Q 12/18 STP7NK80Z - STP7NK80ZFP - STB7NK80Z - STB7NK80Z-1 Package mechanical data TO-220FP MECHANICAL DATA mm. MIN. 4.4 2.5 2.5 0.45 0.75 1.15 1.15 4.95 2.4 10 16 28.6 9.8 2.9 15.9 9 3 30.6 10.6 3.6 16.4 9.3 3.2 1.126 .0385 0.114 0.626 0.354 0.118 TYP MAX. 4.6 2.7 2.75 0.7 1 1.7 1.7 5.2 2.7 10.4 MIN. 0.173 0.098 0.098 0.017 0.030 0.045 0.045 0.195 0.094 0.393 0.630 1.204 0.417 0.141 0.645 0.366 0.126 inch TYP. MAX. 0.181 0.106 0.108 0.027 0.039 0.067 0.067 0.204 0.106 0.409 DIM. A B D E F F1 F2 G G1 H L2 L3 L4 L5 L6 L7 Ø A B L3 L6 L7 F1 D F G1 H F2 L2 L5 E 123 L4 G 13/18 Package mechanical data STP7NK80Z - STP7NK80ZFP - STB7NK80Z - STB7NK80Z-1 D2PAK MECHANICAL DATA TO-247 MECHANICAL DATA mm. DIM. MIN. A A1 A2 B B2 C C2 D D1 E E1 G L L2 L3 M R V2 0º 4.88 15 1.27 1.4 2.4 0.4 4º 10 8.5 5.28 15.85 1.4 1.75 3.2 0.192 0.590 0.050 0.055 0.094 0.015 4.4 2.49 0.03 0.7 1.14 0.45 1.23 8.95 8 10.4 0.393 0.334 0.208 0.625 0.055 0.068 0.126 TYP MAX. 4.6 2.69 0.23 0.93 1.7 0.6 1.36 9.35 MIN. 0.173 0.098 0.001 0.027 0.044 0.017 0.048 0.352 0.315 TYP. MAX. 0.181 0.106 0.009 0.036 0.067 0.023 0.053 0.368 inch 3 1 14/18 STP7NK80Z - STP7NK80ZFP - STB7NK80Z - STB7NK80Z-1 Package mechanical data TO-262 (I2PAK) MECHANICAL DATA mm. DIM. MIN. A A1 b b1 c c2 D e e1 E L L1 L2 4.40 2.40 0.61 1.14 0.49 1.23 8.95 2.40 4.95 10 13 3.50 1.27 TYP MAX. 4.60 2.72 0.88 1.70 0.70 1.32 9.35 2.70 5.15 10.40 14 3.93 1.40 MIN. 0.173 0.094 0.024 0.044 0.019 0.048 0.352 0.094 0.194 0.393 0.511 0.137 0.050 TYP. MAX. 0.181 0.107 0.034 0.066 0.027 0.052 0.368 0.106 0.202 0.410 0.551 0.154 0.055 inch 15/18 Packaging mechanical data STP7NK80Z - STP7NK80ZFP - STB7NK80Z - STB7NK80Z-1 5 Packaging mechanical data D2PAK FOOTPRINT TAPE AND REEL SHIPMENT REEL MECHANICAL DATA DIM. A B C D G N T 1.5 12.8 20.2 24.4 100 30.4 26.4 13.2 mm MIN. MAX. 330 0.059 0.504 0.520 0795 0.960 1.039 3.937 1.197 BULK QTY 1000 inch MIN. MAX. 12.992 TAPE MECHANICAL DATA DIM. A0 B0 D D1 E F K0 P0 P1 P2 R T W mm MIN. 10.5 15.7 1.5 1.59 1.65 11.4 4.8 3.9 11.9 1.9 50 0.25 23.7 24.3 MAX. 10.7 15.9 1.6 1.61 1.85 11.6 5.0 4.1 12.1 2.1 inch MIN. MAX. 0.413 0.421 0.618 0.626 0.059 0.063 0.062 0.063 0.065 0.073 0.449 0.456 0.189 0.197 0.153 0.161 0.468 0.476 0.075 0.082 1.574 0.35 0.0098 0.0137 0.933 0.956 BASE QTY 1000 * on sales type 16/18 STP7NK80Z - STP7NK80ZFP - STB7NK80Z - STB7NK80Z-1 Revision history 6 Revision history Table 8. Date 09-Sep-2004 16-Aug-2006 09-Oct-2006 Revision history Revision 3 4 5 Complete version New template, no content change Corrected order code Changes 17/18 STP7NK80Z - STP7NK80ZFP - STB7NK80Z - STB7NK80Z-1 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2006 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 18/18