BAT30FILM

BAT30 Small signal Schottky diodes Datasheet - production data Description %$7.),/0 6LQJOH The BAT30 series uses 30 V Schottky barrier diodes encapsulated in SOD-523 or SOT-323 packages. 62' %$7&:),/0 &RPPRQFDWKRGH 627 This device is specially suited for switching mode applications needing low forward voltage drop diodes. %$76:),/0 6HULHV &RQILJXUDWLRQLQWRSYLHZ Features  Very low conduction losses Table 1. Device summary  Negligible switching losses  Low forward and reverse recovery times  Extremely fast switching  Surface mount device  Low capacitance diode  ECOPACK®2 and RoHS compliant component April 2015 This is information on a product in full production. DocID12564 Rev 5 Symbol Value IF 300 mA VRRM 30 V C (typ.) 14 pF Tj (max.) 150 °C 1/12 www.st.com Characteristics 1 BAT30 Characteristics Table 2. Absolute ratings (limiting values at Tamb = 25 °C, unless otherwise specified) Symbol VRRM IF Parameter Value Unit Repetitive peak reverse voltage 30 V Continuous forward current 300 mA 1 A A IFSM Surge non repetitive forward current tp = 10 ms Sinusoidal IFRM Repetitive peak forward current, square wave TA = 85 °C, δ = 0.1 0.9 PD(1) Power dissipation SOT-323 225 SOD-523 200 Tstg Storage temperature range mW -65 to +150 °C Tj Maximum operating junction temperature 150 °C TL Maximum soldering temperature 260 °C 1. On epoxy printed circuit board with recommended pad layout Table 3. Thermal parameters Symbol Rth(j-a) Parameter Junction to ambient(1) Value SOT-323 550 SOD-523 600 1. On epoxy printed circuit board with recommended pad layout 2/12 DocID12564 Rev 5 Unit °C/W BAT30 Characteristics Table 4. Static electrical characteristics Symbol Parameter Test conditions Tj = 25 °C IR(1) Reverse leakage current Tj = 70 °C Tj = 85 °C VF(2) Forward voltage drop Min. Typ. Max. VR = 5 V - 0.5 VR = 10 V - 1 VR = 25 V - VR = 30 V - VR = 10 V 0.65 3 µA 5 - 7 20 - 18 50 Unit IF = 0.1 mA - 240 IF = 1 mA - 300 IF = 10 mA - 375 Tj = 25° C IF = 30 mA - 430 IF = 100 mA - 500 IF = 200 mA - 580 IF = 300 mA - mV 530 1. Pulse test: tp = 5 ms,  < 2 % 2. Pulse test: tp = 380 µs,  < 2 % Table 5. Dynamic characteristics Symbol C Parameter Diode capacitance Test conditions Min. Typ. Max. VR = 0 V, F = 1 MHz - 22 - VR = 1 V, F = 1 MHz - 14 - VR = 10 V, F = 1 MHz - 6 - DocID12564 Rev 5 Unit pF 3/12 12 Characteristics BAT30 Figure 1. Power dissipation versus average forward current Figure 2. Continuous forward current versus ambiant temperature P (W) 0.175 ,)$  δ=0.05 0.150 δ=0.1 δ=1 δ=0.5 δ=0.2  627  0.125 62' 0.100  0.075  0.050  T 0.025  IF(AV) (A) 0.000 0.00 δ=tp/T 7 ƒ& DPE tp  0.05 0.10 0.15 0.20 0.25 0.30  0.35 Figure 3. Relative variation of thermal impedance junction to ambient versus pulse duration      Figure 4. Relative variation of thermal impedance junction to ambient versus pulse duration =WKMD5WKMD =WKMD5WKMD ( ( 6LQJOHSXOVH 62' 6LQJOHSXOVH 627 (SR[\SULQWHGERDUG)5 &RSSHUWKLFNQHVV —P (SR[\SULQWHGERDUG)5 &RSSHUVXUIDFH PPð &RSSHUWKLFNQHVV —P ( ( ( ( WSV WSV ( ((( (((( Figure 5. Leakage current versus reverse applied voltage (typical values) (  ,5—$ ( ((((( Figure 6. Relative variation of reverse leakage current versus junction temperature (typical values) ,5>7M@,5>7M ƒ&@ ( 95 9 ( 7M ƒ& ( 7M ƒ& ( ( 7M ƒ& ( ( ( ( 7  ƒ& M ( ( 7Mƒ& 9 9 5 ( (  4/12  DocID12564 Rev 5    BAT30 Characteristics Figure 7. Junction capacitance versus reverse applied voltage (typical values) &S)  Figure 8. Forward voltage drop versus forward current (typical values) ( ,)0$ ) 0+] 9  P9 26& 506 7  ƒ& M ( 7MM  ƒ& ƒ& (  ƒ& 77MM  ƒ& ( ƒ& 77M M  ƒ& ( 9)09 959     (               Figure 9. Forward voltage drop versus forward current (typical values) ( ,)0$ ( ( 7M ƒ& 7M ƒ& ( ( 9)09 (               DocID12564 Rev 5 5/12 12 Package information 2 BAT30 Package information  Epoxy meets UL94, V0  Lead-free packages In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance. ECOPACK® specifications, grade definitions and product status are available at: www.st.com. ECOPACK® is an ST trademark. 2.1 SOD-523 package information Figure 10. SOD-523 package outline (  0 & $ % ( % ' [E  0 & $ % $ ƒ 5 $ F 6($7,1*3/$1( & ƒ / / 6/12 DocID12564 Rev 5 BAT30 Package information Table 6. SOD-523 package mechanical data Dimensions Ref. Inches(1) Millimeters Typ. Min. Max. Typ. Min. Max. A 0.60 0.50 0.70 0.024 0.020 0.028 E 1.60 1.50 1.70 0.063 0.059 0.067 E1 1.20 1.10 1.30 0.047 0.043 0.051 D 0.80 0.70 0.90 0.031 0.028 0.035 b - 0.25 0.35 - 0.010 0.014 c - 0.07 0.20 - 0.003 0.008 L 0.20 0.15 0.25 0.008 0.006 0.010 L1 - 0.05 0.20 - 0.002 0.008 1. Values in inches are converted from mm and rounded to 4 decimal digits. Figure 11. SOD-523 footprint (dimensions in mm)    DocID12564 Rev 5 7/12 12 Package information 2.2 BAT30 SOT-323 package information Figure 12. SOT-323 package outline $ ( H ' E $ F T / + 8/12 DocID12564 Rev 5 BAT30 Package information Table 7. SOT-323 package mechanical data Dimensions Ref. Inches(1) Millimeters Typ. Min. Max. Typ. Min. Max. A - 0.8 1.1 - 0.031 0.043 A1 - 0.0 0.1 - 0.0 0.004 b - 0.25 0.4 - 0.010 0.016 c - 0.1 0.26 - 0.004 0.010 D 2.0 1.8 2.2 0.079 0.071 0.086 E 1.25 1.15 1.35 0.049 0.045 0.053 e 0.65 - - 0.026 - - H 2.1 1.8 2.4 0.083 0.071 0.094 L 0.2 0.1 0.3 0.008 0.004 0.012 q - 0 30° - 0 30° 1. Values in inches are converted from mm and rounded to 4 decimal digits. Figure 13. SOT-323 footprint (dimensions in mm)    DocID12564 Rev 5   9/12 12 Ordering information 3 BAT30 Ordering information Table 8. Ordering information Order code BAT30CWFILM BAT30KFILM BAT30SWFILM Marking Package Weight Base qty. Packing mode C30 SOT-323 Common cathode 6 mg 3000 Tape and reel 30 SOD-523 Single 1.45 mg 3000 Tape and reel S30 SOT-323 Serial 6 mg 3000 Tape and reel Figure 14. Ordering information scheme %$7[[[[),/0 6LJQDO6FKRWWN\GLRGHV 9550 9 &RQILJXUDWLRQ %ODQN 6LQJOHGLRGH & &RPPRQFDWKRGH 6 6HULHVGLRGHV 3DFNDJH . 62' : 627 3DFNLQJ ),/0 7DSHDQGUHHO 10/12 DocID12564 Rev 5 BAT30 4 Revision history Revision history Table 9. Document revision history Date Revision 24-Jul-2006 1 First issue 08-Jul-2009 2 Added SOD-923 package. Table 12 sorted on alphabetic sequence of order code. Updated ECOPACK statement. 13-Oct-2009 3 Updated Table 6 quote “L1” from 0.10 to 0.05. 01-Apr-2014 4 Added Pin 1 anode marker to SOT-666 package graphics. Updated Table 2: Absolute ratings (limiting values at Tamb = 25 °C, unless otherwise specified). 5 Package information updated and removed: SOD-323, SOD-923, SOT-23 and SOT666. Updated cover page. Updated Table 2 and Table 3. Updated Figure 14 and Figure 3. Format updated to current standard. 01-Apr-2015 Changes DocID12564 Rev 5 11/12 12 BAT30 IMPORTANT NOTICE – PLEASE READ CAREFULLY STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgement. Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of Purchasers’ products. No license, express or implied, to any intellectual property right is granted by ST herein. Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product. ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners. Information in this document supersedes and replaces information previously supplied in any prior versions of this document. © 2015 STMicroelectronics – All rights reserved 12/12 DocID12564 Rev 5