BTA41-700BRG

BTA40, BTA41, BTB41 Datasheet 800 V and 600 V, 40 A standard Triacs in TOP3 and RD91 package Features A2 • • • • • G A1 A1 G A2 RD91 A2 Application • A1 A2 G TOP3 Isolated A1 A2 G TOP3 High current Triac Low thermal resistance BTA40 and BTA41 UL1557 recognized components (file ref: 81734) RoHS (2002/95/EC) compliant packages UL-94, V0 flammability package resin compliance • On/off function in static relays, heating regulation, induction motor starting circuits Phase control operations in light dimmers and motor speed controllers Description Available in power packages, the BTA40, BTA41, and BTB41 are suitable for general purpose AC switching. When used with the properly dimensioned heatsink, the BTA40, BTA41 and BTB41 can enable AC switching systems up to 9 kW. Refer to STMicroelectronics application note AN533 for thermal management of Triacs. Product status link BTA40 RD91 package BTA41 TOP3 isolated package BTB41 TOP3 package The BTA40, and BTA41 provides an insulated tab (rated at 2500 V rms). They are recognized by UL. Representative samples of these components have been evaluated by UL and meet applicable UL requirements for the UL 1557 standard (file Ref. 81734). Product summary IT(RMS) 40 A VDRM/VRRM 600 V to 800 V IGT 50 mA DS2111 - Rev 13 - July 2023 For further information contact your local STMicroelectronics sales office. www.st.com BTA40, BTA41, BTB41 Characteristics 1 Characteristics Table 1. Absolute maximum ratings Symbol Parameters IT(RMS) RMS on-state current (180° conduction angle) ITSM BTA40, BTA41 Tc = 80 °C BTB41 Tc = 95 °C Non repetitive surge peak on-state current (full cycle, Tj initial = 25 °C) I2t Critical rate of rise of on-state current dl/dt 420 tp = 20 ms 400 1000 A2s A/µs tp = 20 ms Tj = 25 °C VDRM, VRRM + 100 V tp = 20 µs Tj = 125 °C 8 A Tj = 125 °C 1 W Storage junction temperature range -40 to +150 °C Operating junction temperature range -40 to +125 °C Average gate power dissipation Tj A 50 Peak gate current Tstg A Tj = 125 °C VDSM, VRSM Non repetitive surge peak off-state voltage PG(AV) 40 f = 120 Hz IG = 2 x IGT , tr ≤ 100 ns IGM Unit tp = 16,7 ms tp = 10 ms I2t value for fusing Value Table 2. Electrical characteristics (Tj = 25 °C, unless otherwise specified) - standard (4 quadrants) Symbol Parameters Quadrant I - II - III IGT(1) IV VD = 12 V, RL = 33 Ω VGT VGD IL (dV/dt)c(2) mA 1.3 V I - II - III Min. 0.2 V Max. 80 mA I - III - IV Max. 70 II Max. 160 VD = 67 % VDRM gate open, Tj = 125 °C Min. 500 V/µs (dI/dt)c = 20 A/ms, Tj = 125 °C Min. 10 V/µs IG = 1.2 IGT dV/dt(2) 50 100 Max. IT = 500 mA IH Max. Unit I - II - III VD = VDRM, RL = 3.3 kΩ, Tj = 125 °C (2) Values mA 1. Minimum IGT is guaranteed at 5 % of IGT max. 2. For both polarities of A2 referenced to A1 Table 3. Static electrical characteristics Symbol VTM(1) VTO (1) RD(1) IDRM/IRRM Test conditions Tj Value Unit ITM = 60 A, tp = 380 µs 25 °C Max. 1.55 V threshold on-state voltage 125 °C Max. 0.85 V Dynamic resistance 125 °C Max. 10 mΩ 5 µA 5 mA VT = VDRM, VT = VRRM 25 °C 125 °C Max. 1. For both polarities of A2 referenced to A1 DS2111 - Rev 13 page 2/12 BTA40, BTA41, BTB41 Characteristics Table 4. Thermal resistance Symbol DS2111 - Rev 13 Parameters Rth(j-c) Junction to case (AC) Rth(j-a) Junction to ambient Value BTA40 / BTA41 0.9 BTB41 0.6 BTA40 / BTA41 / BTB41 50 Unit °C/W page 3/12 BTA40, BTA41, BTB41 Characteristics (curves) 1.1 Characteristics (curves) Figure 1. Maximum power dissipation versus on-state RMS current (full cycle) Figure 2. RMS on-state current versus case temperature (full cycle) P(W) 50 IT(RMS)(A) 45 α=180° 40 40 BTB41 35 BTA40 BTA41 30 30 25 20 20 15 180° α 10 0 0 5 10 15 20 10 α IT(RMS) (A) TC(°C) 5 25 30 35 40 0 0 Figure 3. Relative variation of thermal impedance versus pulse duration 1.E+00 K=[Z th /Rth ] 25 50 75 100 125 Figure 4. On-state characteristics (maximum values) ITM (A) 400 Tj max. Vto = 0.85V Rd = 10 mΩ Zth(j-c) 100 Tj = Tj max. 1.E-01 Zth(j-a) BTA / BTB41 Tj = 25°C. 10 1.E-02 1.E-03 1.E-02 1.E-01 1.E+00 0.5 1.E+01 1.E+02 1.0 1.5 2.0 2.5 3.0 ITSM (A) 4.5 5.0 ITSM (A), I²t (A²s) 400 dI/dt limitation: 50A/µs ITSM Tj initial=25 °C Pulse width tp < 10 ms t=20ms Non repetitive Tj initial=25°C 300 4.0 Figure 6. Non-repetitive surge peak on-state current for a sinusoidal pulse 10000 350 3.5 1.E+03 Figure 5. Surge peak on-state current versus number of cycles 450 VTM (V) 1 t p (s) 1.E-03 1000 One cycle 250 200 150 Repetitive TC=70°C 100 50 Number of cycles 0 1 DS2111 - Rev 13 10 100 1000 100 0.01 t p (ms) 0.10 1.00 10.00 page 4/12 BTA40, BTA41, BTB41 Characteristics (curves) Figure 7. Relative variation of gate trigger current, holding and latching current versus junction temperature 2.5 Figure 8. Relative variation of critical rate of decrease of main current versus (dV/dt)c (typical values) (dI/dt)c [(dV/dt)c] / specified (dI/dt)c IGT,IH,IL [ Tj ] / IGT,IH,IL [T j =25°C] 2.0 1.8 2.0 1.6 IGT 1.4 1.5 1.2 IH & IL Typical values 1.0 1.0 0.8 0.5 0.6 Tj (°C) (dV/dt)c (V/µs) 0.4 0.0 -40 -20 0 20 40 60 80 100 120 0.1 140 1.0 10.0 100.0 Figure 9. Relative variation of critical rate of decrease of main current versus junction temperature (typical values) 6 (dI/dt)c [Tj ] / (dI/dt)c [T j specified] 5 4 3 2 1 Tj (°C) 0 0 DS2111 - Rev 13 25 50 75 100 125 page 5/12 BTA40, BTA41, BTB41 Package information 2 Package information In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK packages, depending on their level of environmental compliance. ECOPACK specifications, grade definitions and product status are available at: www.st.com. ECOPACK is an ST trademark. 2.1 TOP3 insulated and non-insulated package information • • • Epoxy meets UL94, V0 Lead-free packages Recommended torque: 1.05 N·m (max. torque: 1.2 N·m) Figure 10. TOP3 insulated and non-insulated package outline DS2111 - Rev 13 page 6/12 BTA40, BTA41, BTB41 TOP3 insulated and non-insulated package information Table 5. TOP3 insulated and non-insulated mechanical data Dimensions Inches(1) mm Ref. Min. Typ. Max. Min. Typ. Max. A 4.40 4.60 0.1732 0.1812 B 1.45 1.55 0.0570 0.0611 C 14.35 15.60 0.5649 0.6142 D 0.50 0.70 0.0196 0.0276 E 2.70 2.90 0.1062 0.1142 F 15.80 16.50 0.6220 0.6497 G 20.40 21.10 0.8031 0.8308 H 15.10 15.50 0.5944 0.6103 J 5.40 5.65 0.2125 0.2225 K 3.40 3.65 0.1338 0.1438 L 4.08 4.17 0.1606 0.1642 P 1.10 1.30 0.0430 0.0510 R 4.60 0.1811 1. Inches given for reference only DS2111 - Rev 13 page 7/12 BTA40, BTA41, BTB41 RD91 package information 2.2 RD91 package information • • • Epoxy meets UL94, V0 Cooling method: Conduction Recommended torque: 0.9 to 1.2 N·m Figure 11. RD91 package outline L2 A2 E L1 B2 B1 C C2 C1 E2 A1 N1 N2 F E3 B I A DS2111 - Rev 13 page 8/12 BTA40, BTA41, BTB41 RD91 package information Table 6. RD91 mechanical data Dimensions Min. A A1 Inches(1) mm Ref. Typ. Max. Min. 40.00 30.10 30.30 Typ. Max. 1.575 1.185 1.193 A2 22.00 0.867 B 27.00 1.063 B1 13.50 16.50 0.531 0.650 B2 24.00 0.945 C 14.00 0.552 C1 3.50 0.138 C2 1.90 2.10 0.074 0.083 E 6.10 6.50 0.240 0.256 E2 4.80 5.20 0.188 0.205 E3 0.70 0.90 0.027 0.036 F 4.00 4.30 0.157 0.170 I 11.20 11.60 0.440 0.536 L1 3.10 3.50 0.122 0.138 L2 1.70 1.90 0.066 0.075 N1 33° 43° 33° 43° N2 28° 38° 28° 38° 1. Inches given for reference only DS2111 - Rev 13 page 9/12 BTA40, BTA41, BTB41 Ordering information 3 Ordering information Figure 12. Ordering information scheme (BTA40, BTA41 and BTB-41 series) BT A 40 - 600 B RG Triac series Insulation A = Insulated B = Non-insulated Current 40 = 40 A in RD91 41 = 40 A in TOP3 or TOP3 insulated Voltage 600 = 600 V 800 = 800 V Sensitive and type B = 50 mA standard Package RG = Tube Blank = Bulk Table 7. Ordering information DS2111 - Rev 13 Order code Marking Package Weight Base qty. Delivery mode BTA40-600B BTA40600B RD91 20 g 25 Bulk BTA40-800B BTA40800B RD91 20 g 25 Bulk BTA41-600BRG BTA41600B TOP3 Ins. 4.5 g 30 Tube BTA41-800BRG BTA41800B TOP3 Ins. 4.5 g 30 Tube BTB41-600BRG BTB41600B TOP3 4.5 g 30 Tube BTB41-800BRG BTB41800B TOP3 4.5 g 30 Tube page 10/12 BTA40, BTA41, BTB41 Revision history Table 8. Document revision history Date Revision Changes Sep-2003 5 Last update. 25-Mar-2005 6 TOP3 delivery mode changed from bulk to tube. 14-Oct-2005 7 Tc values for IT changed in Table 3. ECOPACK statement added. 10-Aug-2009 8 Updated Table 2 to correctly place packages. Updated Figure 2. Table 5 changed to correctly place TOP3. Updated ECOPACK statement. DS2111 - Rev 13 02-Dec-2020 9 Updated Figure 6 and Figure 12. Added Application section. Minor text changes. 28-Jan-2021 10 Updated Table 1 and Table 4. 24-Mar-2021 11 Updated coverimage. 08-Feb-2023 12 Updated Section Description. 26-Jul-2023 13 Updated Table 5. TOP3 insulated and non-insulated mechanical data. page 11/12 BTA40, BTA41, BTB41 IMPORTANT NOTICE – READ CAREFULLY STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgment. Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of purchasers’ products. No license, express or implied, to any intellectual property right is granted by ST herein. Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product. ST and the ST logo are trademarks of ST. For additional information about ST trademarks, refer to www.st.com/trademarks. All other product or service names are the property of their respective owners. Information in this document supersedes and replaces information previously supplied in any prior versions of this document. © 2023 STMicroelectronics – All rights reserved DS2111 - Rev 13 page 12/12