BUL118D

® BUL118D HIGH VOLTAGE FAST-SWITCHING NPN POWER TRANSISTOR s s s s s NPN TRANSISTOR HIGH VOLTAGE CAPABILITY LOW SPREAD OF DYNAMIC PARAMETERS MINIMUM LOT-TO-LOT SPREAD FOR RELIABLE OPERATION VERY HIGH SWITCHING SPEED s APPLICATIONS: ELECTRONIC BALLASTS FOR FLUORESCENT LIGHTING DESCRIPTION The device is manufactured using high voltage Multi Epitaxial Planar technology for high switching speeds and medium voltage capability. It uses a Cellular Emitter structure with planar edge termination to enhance switching speeds while maintaining the wide RBSOA. The device is designed for use in lighting applications and low cost switch-mode power supplies. TO-220 3 1 2 INTERNAL SCHEMATIC DIAGRAM ABSOLUTE MAXIMUM RATINGS Symbol V CES V CEO V EBO IC I CM IB I BM P tot T stg Tj Parameter Collector-Emitter Voltage (V BE = 0 ) Collector-Emitter Voltage (I B = 0 ) Emitter-Base Voltage (I C = 0 ) Collector Current Collector Peak Current (t p < 5 m s) Base Current Base Peak Current (t p < 5 m s) Total Dissipation at T c = 2 5 o C Storage Temperature Max. Operating Junction Temperature Value 700 400 9 3 6 1.5 3 60 -65 to 150 150 Unit V V V A A A A W o o C C December 2002 1/7 BUL118D THERMAL DATA R thj-case R thj-amb Thermal Resistance Junction-Case Thermal Resistance Junction-Ambient Max Max 2.08 62.5 o o C/W C/W ELECTRICAL CHARACTERISTICS (Tcase = 25 oC unless otherwise specified) Symbol I CES I CEO V EBO VCEO(sus) Parameter Collector Cut-off Current (V BE = 0 ) Collector Cut-off Current (I B = 0 ) Emitter-Base Voltage (I C = 0 ) Collector-Emitter Sustaining Voltage (I B = 0 ) Collector-Emitter Saturation Voltage Base-Emitter Saturation Voltage DC Current Gain Test Conditions V CE = 7 00 V V CE = 7 00 V V CE = 4 00 V I E = 1 0 mA I C = 1 00 mA 9 400 T C = 1 25 o C Min. Typ. Max. 100 500 250 Unit µA µA µA V V V CE(sat) ∗ I C = 0 .5 A IC = 1 A IC = 2 A I C = 0 .5 A IC = 1 A IC = 2 A I C = 1 0 mA I C = 0 .5 A IC = 2 A V CC = 1 25 V I B1 = 0 .2 A tp = 20 µs IC = 1 A V BE(off) = -5 V V clamp = 3 00 V (see figure 1) I B = 0 .1 A I B = 0 .2 A I B = 0 .4 A I B = 0 .1 A I B = 0 .2 A I B = 0 .4 A V CE = 5 V V CE = 5 V V CE = 5 V IC = 1 A I B2 = - 0.2 A (see figure 2) I B1 = 0 .2 A L = 50 mH R BB = 0 Ω 10 10 8 0.4 3.2 0.25 0.8 0.16 0.5 1 1.5 1 1.2 1.3 50 V V V V V V V BE(sat) ∗ h FE ∗ tr ts tf ts tf Vf RESISTIVE LOAD Rise Time Storage Time Fall Time INDUCTIVE LOAD Storage Time Fall Time 0.7 4.5 0.4 µs µs µs µs µs Diode Forward Voltage I F = 1 A 2 .5 V ∗ Pulsed: Pulse duration = 300 µs, duty cycle 1.5 % 2/7 BUL118D Safe Operating Area Derating Curve DC Current Gain DC Current Gain Collector Emitter Saturation Voltage Base Emitter Saturation Voltage 3/7 BUL118D Inductive Load Fall Time Inductive Load Storage Time Resistive Load Fall Time Resistive Load Storage Time Reverse Biased SOA 4/7 BUL118D Figure 1: Inductive Load Switching Test Circuit. 1) Fast electronic switch 2) Non-inductive Resistor 3) Fast recovery rectifier Figure 2: Resistive Load Switching Test Circuit. 1) Fast electronic switch 2) Non-inductive Resistor 5/7 BUL118D TO-220 MECHANICAL DATA DIM. A C D E F F1 F2 G G1 H2 L2 L4 L5 L6 L7 L9 M DIA. 3.75 13.00 2.65 15.25 6.20 3.50 2.60 3.85 0.147 mm MIN. 4.40 1.23 2.40 0.49 0.61 1.14 1.14 4.95 2.40 10.00 16.40 14.00 2.95 15.75 6.60 3.93 0.511 0.104 0.600 0.244 0.137 0.102 0.151 TYP. MAX. 4.60 1.32 2.72 0.70 0.88 1.70 1.70 5.15 2.70 10.40 MIN. 0.173 0.048 0.094 0.019 0.024 0.044 0.044 0.194 0.094 0.394 0.645 0.551 0.116 0.620 0.260 0.154 inch TYP. MAX. 0.181 0.052 0.107 0.027 0.034 0.067 0.067 0.202 0.106 0.409 P011CI 6/7 BUL118D Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specification mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a trademark of STMicroelectronics © 2002 STMicroelectronics – Printed in Italy – All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - Canada - China - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco Singapore - Spain - Sweden - Switzerland - United Kingdom - United States. http://www.st.com 7/7