BULB128D-1

® BULB128D-1 HIGH VOLTAGE FAST-SWITCHING NPN POWER TRANSISTOR O rdering Code BULB128D-1 s Marking BULB128D Shipment Tube s s s s s s STMicroelectronics PREFERRED SALESTYPE NPN TRANSISTOR HIGH VOLTAGE CAPABILITY LOW SPREAD OF DYNAMIC PARAMETERS MINIMUM LOT-TO-LOT SPREAD FOR RELIABLE OPERATION VERY HIGH SWITCHING SPEED INTEGRATED ANTIPARALLEL COLLECTOR-EMITTER DIODE 3 12 I2PAK (TO-262) APPLICATIONS: ELECTRONIC BALLASTS FOR FLUORESCENT LIGHTING s FLYBACK AND FORWARD SINGLE TRANSISTOR LOW POWER CONVERTERS s INTERNAL SCHEMATIC DIAGRAM DESCRIPTION The device is manufactured using high voltage Multi Epitaxial Planar technology for high switching speeds and medium voltage capability. It uses a Cellular Emitter structure with planar edge termination to enhance switching speeds while maintaining the wide RBSOA. The device is designed for use in lighting applications and low cost switch-mode power supplies. ABSOLUTE MAXIMUM RATINGS Symbol V CES V CEO V EBO IC I CM IB I BM P tot T stg Tj Parameter Collector-Emitter Voltage (V BE = 0) Collector-Emitter Voltage (I B = 0) Emitter-Base Voltage (I C = 0 , IB = 2 A , t p < 10 µ s, T j < 150 o C) Collector Current Collector Peak Current (t p < 5 m s) Base Current Base Peak Current (t p < 5 m s) Total Dissipation at T c = 2 5 o C Storage Temperature Max. Operating Junction Temperature Value 700 400 V (BR)EBO 4 8 2 4 70 -65 to 150 150 Unit V V V A A A A W o C o C 1/7 September 2003 BULB128D-1 THERMAL DATA R thj-case R thj-amb Thermal Resistance Junction-Case Thermal Resistance Junction-Ambient Max Max 1.78 62.5 o o C/W C/W ELECTRICAL CHARACTERISTICS (Tcase = 25 oC unless otherwise specified) Symbol I CES I CEO V (BR)EBO Parameter Collector Cut-off Current (V BE = 0 V) Collector Cut-off Current (I B = 0 ) Emitter-Base Breakdown Voltage (I C = 0 ) Test Conditions V CE = 7 00 V V CE = 7 00 V V CE = 4 00 V I E = 1 0 mA 9 T C = 1 25 o C Min. Typ. Max. 100 500 250 18 Unit µA µA µA V V CEO(sus) ∗ Collector-Emitter Sustaining Voltage (I B = 0) V CE(sat) ∗ Collector-Emitter Saturation Voltage I C = 1 00 mA L = 25 mH 400 V IC IC IC IC = = = = 0 .5 A 1A 2 .5 A 4A IB IB IB IB = = = = 0 .1 A 0 .2 A 0 .5 A 1A 0.7 1 1.5 0.5 1.1 1.2 1.3 10 12 32 2.5 V V V V V V V V BE(sat) ∗ Base-Emitter Saturation Voltage DC Current Gain Forward Voltage Drop INDUCTIVE LOAD Storage Time Fall Time RESISTIVE LOAD Storage Time Fall Time I C = 0 .5 A IC = 1 A I C = 2 .5 A I C = 1 0 mA IC = 2 A If = 2 A V CC = 2 00 V I B1 = 0 .4 A R BB = 0 Ω (see fig.1) V CC = 2 50 V I B1 = 0 .4 A T p = 3 00 µ s I B = 0 .1 A I B = 0 .2 A I B = 0 .5 A V CE = 5 V V CE = 5 V IC = 2 A V BE(off) = - 5 V L = 2 00 µ H IC = 2 A I B2 = - 0.4 A (see fig.2) h FE ∗ Vf ts tf V µs µs 0.6 0.1 ts tf 2 0.2 2.9 µs µs ∗ Pulsed: Pulse duration = 300 µs, duty cycle 1.5 % 2/7 BULB128D-1 Safe Operating Areas Derating Curve DC Current Gain DC Current Gain Collector Emitter Saturation Voltage Base Emitter Saturation Voltage 3/7 BULB128D-1 Inductive Fall Time Inductive Storage Time Resistive Load Fall Time Resistive Load Storage Time Reverse Biased SOA 4/7 BULB128D-1 Figure 1: Inductive Load Switching Test Circuits. 1) Fast electronic switch 2) Non-inductive Resistor 3) Fast recovery rectifier Figure 2: Resistive Load Switching Test Circuits. 1) Fast electronic switch 2) Non-inductive Resistor 5/7 BULB128D-1 TO-262 (I2PAK) MECHANICAL DATA mm MIN. A A1 B B2 C C2 D e E L L1 L2 4.4 2.49 0.7 1.14 0.45 1.23 8.95 2.4 10 13.1 3.48 1.27 TYP. MAX. 4.6 2.69 0.93 1.7 0.6 1.36 9.35 2.7 10.4 13.6 3.78 1.4 MIN. 0.173 0.098 0.027 0.044 0.017 0.048 0.352 0.094 0.393 0.515 0.137 0.050 inch TYP. MAX. 0.181 0.106 0.036 0.067 0.023 0.053 0.368 0.106 0.409 0.531 0.149 0.055 DIM. A C2 B2 B E L1 L2 D L P011P5/E 6/7 e A1 C BULB128D-1 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specification mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a trademark of STMicroelectronics. All other names are the property of their respective owners. © 2003 STMicroelectronics – All Rights reserved STMicroelectronics GROUP OF COMPANIES Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States. http://www.st.com 7/7