DSL02-010SC5

DSL02 Low capacitance TVS for high speed lines such as xDSL Datasheet - production data Description DSL02 is designed to protect DSL line drivers against surges defined in worldwide telecommunication standards. This device protects line drivers of various systems such as ADSL and VDSL. The low capacitance makes it suitable from ADSL to VDSL data rates. DSL02 is able to survive severe conditions even when used with downgraded or oscillating gas tube. 627/6& DSL02 is also suitable to be used on other lines when IEC61000-4-5 surge capability is required. Features • High surge capability to comply with GR-1089 and ITU-T K20/21 DSL02 is packaged in a SOT23-5L. • Keeps its peak power capability up to Tj max Figure 1. Functional diagram • Stand-off voltage: 5 V, 8 V, 10 V • Low capacitance device: Ctyp = 3 pF • RoHS package I/O1 • Low leakage current: 0.5 µA at 25 °C Complies with the following standards I/O2 • Telcordia GR-1089 – 2.5 kV 2/10 µs - 500 A 2/10 µs – AC power fault tests I/O2 I/O1 I/O2 • ITU-T K20/21/45 – 6 kV 10/700 µs - 150 A 5/310 µs – power induction tests – power contact tests • IEC 61000-4-2, level 4 – 15 kV (air discharge) – 8 kV (contact discharge • IEC 61000-4-5, level 3 – ±2 kV, 42 Ω • MIL STD 883G-Method 3015-7: Class 3 – 8 kV (human body model) February 2015 This is information on a product in full production. DocID024717 Rev 2 1/8 www.st.com Characteristics 1 DSL02 Characteristics Table 1. Absolute ratings (Tamb = 25 °C) Symbol Parameter Value Unit VPP Peak pulse voltage IEC 61000-4-2, contact discharge 30 kV Ipp Peak pulse current 8/20 µs 30 A -55 to 150 -40 to 125 °C °C 260 °C C ΔC Tstg Tj Storage temperature range Operating junction temperature range TL Maximum temperature for soldering during 10 s Table 2. Electrical characteristics (Tamb = 25 °C) IRM @ VRM VCL @ IPP VBR @ IBR (8/20 µs) Order code Max. µA V Min. Max. mA V A V Typ. Max. Typ. pF(1) pF(1) pF(2) DSL02-005SC5 0.5 5 6 1 18 24 3 5 0.3 DSL02-008SC5 0.5 8 10 1 22 24 3 5 0.3 DSL02-010SC5 0.5 10 11 1 24 24 3 5 0.3 1. Test conditions: VR = 2 V bias, VRMS = 1 V, F = 1 MHz 2. Measured between 1 V and VRM Figure 2. Peak pulse power dissipation versus initial junction temperature (typical values, 8/20µs) Ppp (W) Figure 3. Leakage current versus junction temperature (typical values) 100 1000 IR (nA) VR=VRM 8/20 µs 900 800 700 10 600 500 400 1 300 200 100 Tj(°C) T j (°C) 0 0 0 2/8 25 50 75 100 125 150 25 DocID024717 Rev 2 50 75 100 125 DSL02 Characteristics Figure 4. Junction capacitance versus reverse voltage applied (typical values) 3.0 C (pF) F=1 MHz Vosc=1VRMS Tj=25 °C For lower voltages, maximum voltage applied is limited to V RM 2.5 2.0 1.5 1.0 0.5 VR(V) 0.0 1 2 3 4 5 6 7 8 Figure 5. xDSL2 modem connection 9/' 9/' /LQHGULYHUV 9/' 9/' DocID024717 Rev 2 3/8 8 Package information 2 DSL02 Package information • Epoxy meets UL94, V0 • Lead-free package In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance. ECOPACK® specifications, grade definitions and product status are available at: www.st.com. ECOPACK® is an ST trademark. Figure 6. SOT23-5L dimension definitions A1 c q L H A E e D b e A2 Table 3. SOT23-5L dimension values Dimensions Ref. Millimeters Min. Max. Min. Typ. Max. A 0.90 1.45 0.035 0.057 A1 0 0.15 0 0.006 A2 0.90 1.30 0.035 0.051 b 0.30 0.50 0.012 0.020 c 0.09 0.20 0.004 0.008 D 2.80 3.05 0.11 0.118 E 1.50 1.75 0.059 0.069 e 4/8 Typ. Inches 0.95 0.037 H 2.60 3.00 0.102 0.118 L 0.30 0.60 0.012 0.024 M 0° 10° 0° 10° DocID024717 Rev 2 DSL02 Package information Figure 7. Footprint recommendations dimensions in mm (inches) Figure 8. Marking layout     x x xx         DocID024717 Rev 2 5/8 8 PCB recommendation 3 DSL02 PCB recommendation Figure 9. Recommended layout 1 5 2 3 4 Concerning Figure 9: 6/8 • Pins 1 and 5 must be connected together. • Pins 3 and 4 must be connected together. • Pin 2 must not be connected DocID024717 Rev 2 PCB tracks DSL02 4 Ordering information Ordering information Figure 10. Ordering information scheme DSL 0x - vvv SC5 DSL protection Version Stand-off voltage 010 = 10 V Package SC5 = SOT23-5L Table 4. Ordering information 5 Order code Marking DSL02-005SC5 YT05 DSL02-008SC5 YT08 DSL02-010SC5 YT10 Package Weight Base qty Delivery mode SOT23-5L 16 mg 3000 Tape and reel Revision history Table 5. Document revision history Date Revision Changes 30-Oct-2013 1 Initial release. 03-Feb-2015 2 Updated Features and Description. Added Figure 5. DocID024717 Rev 2 7/8 8 DSL02 IMPORTANT NOTICE – PLEASE READ CAREFULLY STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgement. Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of Purchasers’ products. No license, express or implied, to any intellectual property right is granted by ST herein. Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product. ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners. Information in this document supersedes and replaces information previously supplied in any prior versions of this document. © 2015 STMicroelectronics – All rights reserved 8/8 DocID024717 Rev 2