ESDA6V1-5SC6Y

ESDA6V1-5SC6Y Automotive-grade 5-line transient voltage suppressor (TVS) for ESD protection Datasheet - production data Applications This device is used to protect equipment in which ESD and EOS transient overvoltage may damage electronic circuits. Description This device is a monolithic voltage suppressor designed to protect components connected to data and transmission lines against ESD. It clamps the voltage just above the logic level supply for positive transients, and to a diode drop below ground for negative transients. SOT23-6L Figure 1: Pin configuration Features     AEC-Q101 qualified 5 unidirectional TVS functions UL 94 V-0 J-STD-020 MSL level 1 Benefits  I/O1 I/O5 Gnd I/O4 I/O2 I/O3 Suitable for high density boards Complies with the following standards    ISO 10605 / IEC 61000-4-2: C = 150 pF, R = 330 Ω  30 kV (air discharge)  18 kV (contact discharge) ISO 10605: C = 330 pF, R = 330 Ω  20 kV (air discharge)  13 kV (contact discharge) ISO 7637-3  Pulse 3a: VS = -150 V  Pulse 3b: VS = +100 V May 2017 DocID029995 Rev 3 This is information on a product in full production. 1/12 www.st.com Characteristics 1 ESDA6V1-5SC6Y Characteristics Table 1: Absolute ratings (Tamb = 25 °C) Symbol Vpp Parameter Peak pulse voltage Value ISO 10605 / IEC 61000-4-2 (C = 150 pF, R = 330 Ω) Contact discharge Air discharge 30 18 ISO10605 (C = 330 pF, R = 330 Ω) Contact discharge Air discharge 20 13 Unit kV Ipp Peak pulse current Ppp Peak pulse power Tstg Storage temperature range -65 to +150 Tj Operating junction temperature range -40 to +150 TL Maximum temperature for soldering during 10 s 8/20μs 7 A 80 W 260 °C °C Figure 2: Electrical characteristics (definitions) Table 2: Electrical characteristics - values (Tamb = 25 °C) VBR at IR Order code ESDA6V1-5SC6Y Min. Max. IRM at VRM VCL at Ipp(1) Max. Max. 2/12 Cline Max. Max. Typ. pF 50 V V mA µA V V A V mA 10-4/C 6.1 7.2 1 1 5.2 11.4 7 1.25 200 6 Notes: (1)8/20 μs waveform (2)V at Tj = VBR at 25 °C x (1 + αT x (Tj - 25 )) BR αT(2) VF at IF DocID029995 Rev 3 ESDA6V1-5SC6Y Characteristics Figure 3: Pulse definition for electrical characteristics 110 100 90 IPP% tr = rise time tp = pulse duration time tr 80 70 60 50 tp 40 30 20 10 t (µs) 0 DocID029995 Rev 3 3/12 Characteristics 1.1 ESDA6V1-5SC6Y Characteristics (curves) Figure 4: Pulse power versus junction temperature P (W) 1000 PP Ppp(W) 100 Figure 5: Peak pulse power versus exponential pulse duration 8/20 µs 90 80 70 60 50 100 40 30 20 10 0 Tj (° C) 0 25 50 75 100 125 150 tp(µs) 175 10 10 Figure 6: Clamping voltage versus peak pulse current 10 1000 Figure 7: Leakage current versus junction temperature 1000 IPP(A) 100 IR(nA) VRM = 5.2 V 8/20 µs 100 1 V CL (V) 0.1 6 7 8 9 10 11 12 T j (°C) 10 25 Figure 8: ESD response to IEC 61000-4-2 (+8 kV contact discharge) 50 75 100 125 Figure 9: ESD response to IEC 61000-4-2 (-8 kV contact discharge) 79.8 V -4.6 V 11.8 V 4/12 10.4 V 7.1 V DocID029995 Rev 3 -82.6 V -2.1 V -710 mV 150 ESDA6V1-5SC6Y Characteristics Figure 10: ISO7637-3 pulse 3a response (VS = -150 V) 1 V/div 0.5 A/div 50 ns/div Figure 11: ISO7637-3 pulse 3b response (VS = 100 V) 2 V/div 0.5 A/div 50 ns/div DocID029995 Rev 3 5/12 Application and design guidelines 2 ESDA6V1-5SC6Y Application and design guidelines Further information can be found in AN2689 titled: “Protection of automotive electronics from electrical hazards, guidelines for design and component selection”. 6/12 DocID029995 Rev 3 ESDA6V1-5SC6Y 3 Package information Package information In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance. ECOPACK® specifications, grade definitions and product status are available at: www.st.com. ECOPACK® is an ST trademark.   3.1 Epoxy meets UL 94,V0 Lead-free package SOT23-6L package information Figure 12: SOT23-6L package outline Table 3: SOT23-6L package mechanical data Dimensions Ref. Millimeters Min. Typ. Inches Max. Min. Typ. Max. A 0.9 1.45 0.0354 0.0571 A1 0 0.15 0 0.0059 A2 0.9 1.3 0.0354 0.0512 b 0.30 0.5 0.0118 0.0197 c 0.09 0.2 0.0035 0.0079 D 2.8 3.05 0.1102 0.1201 E 1.5 1.75 0.0591 0.0689 e 0.95 0.0374 H 2.6 3 0.1024 0.1181 L 0.3 0.6 0.0118 0.0236 θ 0 10 0 0.3937 DocID029995 Rev 3 7/12 Package information 8/12 ESDA6V1-5SC6Y Figure 13: Footprint recommendations, dimensions in mm (inches) Figure 14: Marking layout (refer to ordering information table for marking) Figure 15: Package orientation in reel Figure 16: Tape and reel orientation Figure 17: Reel dimensions (mm) Figure 18: Inner box dimensions (mm) DocID029995 Rev 3 ESDA6V1-5SC6Y Package information Figure 19: Tape and reel outline Table 4: Tape and reel mechanical data Dimensions Ref. P1 Millimeters Min. Typ. Max. 3.9 4 4.1 P0 3.9 4 4.1 D0 1.45 1.5 1.6 D1 1 F 3.45 3.5 3.55 K0 1.3 1.4 1.6 P2 1.95 2 2.05 W 7.9 8 8.3 DocID029995 Rev 3 9/12 Ordering information 4 ESDA6V1-5SC6Y Ordering information Figure 20: Ordering information scheme ESDA xx - 5 SC6 Y ESD array Breakdown voltage Numbers of lines protected Package SC6 = SOT23-6L Automotive grade Table 5: Ordering information 10/12 Order code Marking Package Weight Base qty. Delivery mode ESDA6V1-5SC6Y EC6Y SOT23-6L 14 mg 3000 Tape and reel DocID029995 Rev 3 ESDA6V1-5SC6Y 5 Revision history Revision history Table 6: Document revision history Date Revision Changes 08-Nov-2016 1 Initial release. 15-Mar-2017 2 Updated title and description in cover page. Minor text changes to improve readability. 03-May-2017 3 Formatting improvement, no content changes. DocID029995 Rev 3 11/12 ESDA6V1-5SC6Y IMPORTANT NOTICE – PLEASE READ CAREFULLY STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgement. Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of Purchasers’ products. No license, express or implied, to any intellectual property right is granted by ST herein. Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product. ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners. Information in this document supersedes and replaces information previously supplied in any prior versions of this document. © 2017 STMicroelectronics – All rights reserved 12/12 DocID029995 Rev 3