EV-VND7004AY

EV-VND7004AY VND7004AY Evaluation Board Data brief – Multiplexed analog feedback of: load current with high precision proportional current mirror, VCC supply voltage and TCHIP device temperature – Overload and short to ground (power limitation) indication – Thermal shutdown indication – OFF-state open-load detection – Output short to VCC detection – Sense enable/ disable Features Max transient supply voltage VCC 40 V Operating voltage range VCC 4 to 28 V Typ. on-state resistance (per Ch) RON 4 mΩ Current limitation (typ) ILIMH 100 A Stand-by current (max) ISTBY 0.5 µA  Protections – Undervoltage shutdown – Overvoltage clamp – Load current limitation – Self limiting of fast thermal transients – Configurable latch-off on overtemperature or power limitation with dedicated fault reset pin – Loss of ground and loss of VCC – Reverse battery through self turn-on – Electrostatic discharge protection Applications  Simple single IC application board dedicated for VND7004AY  Provides electrical connectivity and thermal heat-sinking for easy prototyping  General device features – Double channel smart high-side driver with MultiSense analog feedback – Very low standby current – Compatible with 3 V and 5 V CMOS outputs Specially intended for Automotive Smart Power Distribution, Glow Plug, Heating Systems, DC Motors, Relay replacement and high power resistive and inductive actuators. Description This board provides you an easy way to connect STMicroelectronics® VIPower® M0-7 technology into your existing system. Table 1. Device summary Order Code Reference EV-VND7004AY VND7004AY Evaluation Board  Diagnostic functions October 2016 DocID029896 Rev 1 For further information contact your local STMicroelectronics sales office. 1/8 www.st.com Overview 1 EV-VND7004AY Overview The board comes pre-assembled with VND7004AY high-side driver. On board, a minimum set of electrical components (as for device datasheet recommendation), is enabling the user to directly connect the load, the power supply and the microcontroller without any additional effort in external component design and connection. The VND7004AY is a double channel high-side driver manufactured using ST proprietary VIPower technology and housed in PowerSSO-36 packages. The device is designed to drive 12 V automotive grounded loads through a 3 V and 5 V CMOS-compatible interface, and to provide protection and diagnostics. The device integrates also advanced protective functions such as load current limitation, overload active management by power limitation and overtemperature shutdown. A FaultRST pin unlatches the output in case of fault or disables the latch-off functionality. A dedicated multifunction multiplexed analog output pin delivers sophisticated diagnostic functions including high precision proportional load current sense, supply voltage feedback and chip temperature sense, in addition to the detection of overload and short circuit to ground, short to VCC and OFF-state open-load. A sense enable pin allows OFF-state diagnosis to be disabled during the module low-power mode as well as external sense resistor sharing among similar devices. Figure 1. EV-VND7004AY schematic 2/8 DocID029896 Rev 1 EV-VND7004AY 2 Board connections Board connections Figure 2 shows the placement of the connectors to be used for supplying the evaluation board, connecting the load and controlling the functionality and diagnostic of the device. Figure 2. Evaluation board connections Table 2. J3 connector: pin functions Connector Pin number Pin name Pin function J3 1…4 N/A J3 5 IN_PullUP J3 6 +5 V J3 7 FaultRST J3 8 MultiSense Multiplexed analog sense output pin; it delivers a current proportional to the selected diagnostic: load current, supply voltage or chip temperature. J3 9 S_EN Active high compatible with 3 V and 5 V CMOS outputs pin; it enables the MultiSense diagnostic pin. J3 10...11 SEL0,1 Active high compatible with 3 V and 5 V CMOS outputs pin; they address the MultiSense multiplexer. J3 12 N/A Not connected J3 13...14 IN0,1 Voltage controlled input pin with hysteresis, compatible with 3 V and 5 V CMOS outputs. They control output switch state. J3 15...18 N/A Not connected Not connected Connection to optional external pull-up resistor for open load detection in off-state. 5 V Power Supply Active low compatible with 3 V and 5 V CMOS outputs pin; it unlatches the output in case of fault; If kept low, sets the outputs in auto-restart mode. DocID029896 Rev 1 3/8 6 Board connections EV-VND7004AY In case the user wishes to utilize the Current Sense / MultiSense function of the device, it is necessary to plug a sense resistor in Rsense. The package includes a through-hole resistor, to be mounted on TP1-TP2 - see Figure 4. Different Rsense values can be adopted based on user preference. Another option is soldering an SMD resistor on the dedicated PCB pad, as shown in Figure 5. Figure 3. No sense resistor Figure 4. Mounting through-hole sense resistor 4/8 DocID029896 Rev 1 EV-VND7004AY Board connections Figure 5. Pads for soldering SMD resistor DocID029896 Rev 1 5/8 6 Thermal data 3 EV-VND7004AY Thermal data Table 3. EV-VND7004AY thermal data Symbol Parameter Max Unit Rthj-amb Thermal resistance junction-ambient (MAX) 39° °C/W Table 4. PCB specifications 6/8 Parameter Value Board dimensions 25 mm x 41.5 mm Number of Cu layer 2 Layer Cu thickness 35 μm Board finish thickness 1.6 mm +/- 10% Board Material FR4 Thermal vias diameter 0.5 mm DocID029896 Rev 1 EV-VND7004AY 4 Revision history Revision history Table 5. Document revision history Date Revision 21-Oct-2016 1 Changes Initial release. DocID029896 Rev 1 7/8 7 EV-VND7004AY IMPORTANT NOTICE – PLEASE READ CAREFULLY STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgement. Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of Purchasers’ products. No license, express or implied, to any intellectual property right is granted by ST herein. Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product. ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners. Information in this document supersedes and replaces information previously supplied in any prior versions of this document. © 2016 STMicroelectronics – All rights reserved 8/8 DocID029896 Rev 1