L6562A_0708

L6562A Transition-mode PFC controller Features ■ ■ ■ ■ ■ ■ ■ ■ ■ Proprietary multiplier design for minimum THD Very accurate adjustable output overvoltage protection Ultra-low (30µA) Start-up current Low (2.5mA) quiescent current Digital leading-edge blanking on current sense Disable function on E/A input 1% (@ TJ = 25 °C) internal reference voltage -600/+800mA totem pole gate driver with active pull-down during UVLO and voltage clamp DIP-8/SO-8 packages Block diagram DIP-8 SO-8 Applications PFC pre-regulators for: ■ ■ ■ ■ IEC61000-3-2 compliant SMPS (Flat TV, monitors, desktop PC, games) HI-END AC-DC adapter/charger up to 400W Electronic ballast Entry level server & web server Figure 1. Table 1. Device summary Order codes L6562AN L6562AD L6562ADTR August 2007 Package DIP-8 SO-8 SO-8 Rev 3 Packaging Tube Tube Tape & Reel 1/26 www.st.com 26 Contents L6562A Contents 1 2 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Pin settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2.1 2.2 Pin connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3 4 5 6 7 Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Thermal data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Typical electrical characteristic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Application information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 7.1 7.2 7.3 7.4 7.5 Overvoltage protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Disable function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 THD optimizer circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Operating with no auxiliary winding on the boost inductor . . . . . . . . . . . . 16 Comparison between the L6562A and the L6562 . . . . . . . . . . . . . . . . . . 17 8 9 10 Application examples and ideas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 2/26 L6562A Description 1 Description The L6562A is a current-mode PFC controller operating in Transition Mode (TM). Coming with the same pin-out as its predecessors L6561 and L6562, it offers improved performance. The highly linear multiplier includes a special circuit, able to reduce AC input current distortion, that allows wide-range-mains operation with an extremely low THD, even over a large load range. The output voltage is controlled by means of a voltage-mode error amplifier and an accurate (1% @TJ = 25°C) internal voltage reference. The device features extremely low consumption (60µA max. before start-up and 0 due to a load drop, the voltage at pin INV will be kept at 2.5V by the local feedback of the error amplifier, a network connected between pins INV and COMP that introduces a long time constant to achieve high PF (this is why ∆Vo can be large). As a result, the current through R2 will remain equal to 2.5/R2 but that through R1 will become: Equation 2 V O – 2.5 + ∆V O I' R1 = --------------------------------------R1 The difference current ∆IR1=I'R1-IR2=I'R1-IR1= ∆Vo/R1 will flow through the compensation network and enter the error amplifier output (pin COMP). This current is monitored inside the device and if it reaches about 24µA the output voltage of the multiplier is forced to decrease, thus smoothly reducing the energy delivered to the output. As the current exceeds 27µA, the OVP is triggered (Dynamic OVP): the gate-drive is forced low to switch off the external power transistor and the IC put in an idle state. This condition is maintained until the current falls below approximately 7µA, which re-enables the internal starter and allows switching to restart. The output ∆Vo that is able to trigger the Dynamic OVP function is then: Equation 3 ∆VO = R1 · 20 · 10 - 6 An important advantage of this technique is that the OV level can be set independently of the regulated output voltage: the latter depends on the ratio of R1 to R2, the former on the individual value of R1. Another advantage is the precision: the tolerance of the detection current is 13%, i.e. 13% tolerance on ∆Vo. Since ∆Vo