LD1084V50

LD1084 SERIES 5A LOW DROP POSITIVE VOLTAGE REGULATOR ADJUSTABLE AND FIXED s s s s s s s s TYPICAL DROPOUT 1.3V (AT 5A) THREE TERMINAL ADJUSTABLE OR FIXED OUTPUT VOLTAGE 1.5, 1.8V, 2.5V, 2.85V, 3.3V, 3.6V, 5V, 8V, 9V, 12V. GUARANTEED OUTPUT CURRENT UP TO 5A OUPUT TOLERANCE ±1% AT 25°C AND ±2% IN FULL TEMPERATURE RANGE INTERNAL POWER AND THERMAL LIMIT WIDE OPERATING TEMPERATURE RANGE -40°C TO 125°C PACKAGE AVAILABLE : TO-220, D2PAK, D2PAK/A PINOUT COMPATIBILITY WITH STANDARD ADJUSTABLE VREG D2PAK TO-220 D2PAK/A DESCRIPTION The LD1084 is a LOW DROP Voltage Regulator able to provide up to 5A of Output Current. Dropout is guaranteed at a maximum of 1.5V at the maximum output current, decreasing at lower loads. The LD1084 is pin to pin compatible with the older 3-terminal adjustable regulators, but has better performances in term of drop and output tolerance . A 2.85V output version is suitable for SCSI-2 active termination. Unlike PNP regulators, where a part of the output current is wasted as quiescent current, the LD1084 quiescent current flows into the load, so increase efficiency. Only a 10µF minimum capacitor is need for stability. The device is supplied in TO-220, D2PAK and D2PAK/A. On chip trimming allows the regulator to reach a very tight output voltage tolerance, within ±1% at 25°C. SCHEMATIC DIAGRAM May 2003 1/18 LD1084 SERIES ABSOLUTE MAXIMUM RATINGS Symbol VI IO PD Tstg Top DC Input Voltage Output Current Power Dissipation Storage Temperature Range Operating Junction Temperature Range Parameter² Value 30 Internally Limited Internally Limited -55 to +150 -40 to +125 Unit V mA mW °C °C Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these condition is not implied. THERMAL DATA Symbol Rthj-case Rthj-amb Parameter Thermal Resistance Junction-case Thermal Resistance Junction-ambient TO-220 3 50 D2PAK 3 62.5 Unit °C/W °C/W APPLICATION CIRCUITS R2 VO = VREF (1 +  ) R1 CONNECTION DIAGRAM (top view) TO-220 D2PAK D2PAK/A 2/18 LD1084 SERIES ORDERING CODES TYPE LD1084V15 LD1084V18 LD1084V25 LD1084V28 LD1084V33 LD1084V36 LD1084V50 LD1084V80 LD1084V90 LD1084V120 LD1084V D2PAK (*) LD1084D2T15 LD1084D2T18 LD1084D2T25 LD1084D2T28 LD1084D2T33 LD1084D2T36 LD1084D2T50 LD1084D2T80 LD1084D2T90 LD1084D2T120 LD1084D2T D2PAK/A LD1084D2M15 LD1084D2M18 LD1084D2M25 LD1084D2M28 LD1084D2M33 LD1084D2M36 LD1084D2M50 LD1084D2M80 LD1084D2M90 LD1084D2M120 LD1084D2M OUTPUT VOLTAGE 1.5 V 1.8 V 2.5 V 2.85 V 3.3 V 3.6 V 5.0 V 8.0 V 9.0 V 12.0 V ADJ (*) Available in Tape & Reel with the suffix "R" for fixed versions and "-R" for adjustable version LECTRICAL CHARACTERISTICS OF LD1084#15 (VI=4.5V, C I = CO =10µF, TA = -40 to 125°C, unless otherwise specified.) Symbol VO ∆VO ∆VO Vd Iq Isc Parameter Output Voltage Line Regulation Load Regulation Dropout Voltage Quiescent Current Short Circuit Current Termal Regulation SVR eN S S Supply Voltage Rejection RMS Output Noise Voltage (% of VO) Temperature Stability Long Term Stability IO = 0 mA Test Conditions TJ = 25°C IO = 0 to 5A VI = 3.1 to 30V (note 1) IO = 0 mA VI = 3.1 to 18V TJ = 25°C IO = 0 mA IO = 0 to 5A IO =5 A VI ≤ 30V VI - VO = 5V VI - VO = 25V TA = 25°C, 30ms pulse f = 120 Hz, CO = 25 µF, IO = 5A VI = 6.8 ± 3V TA = 25°C f =10Hz to 10KHz 60 5.5 0.5 VI = 3.1 to 15V IO = 0 to 5A TJ = 25°C Min. 1.485 1.47 Typ. 1.5 1.5 0.5 0.1 3 7 1.3 5 6.5 0.7 0.003 75 0.003 0.5 0.5 0.015 Max. 1.515 1.53 6 6 15 20 1.5 10 Unit V V mV mV mV V V mA A A %/W dB % % % TA = 125°C 1000Hrs NOTE 1: See short-circuit current curve for available output current at fixed dropout. 3/18 LD1084 SERIES ELECTRICAL CHARACTERISTICS OF LD1084#18 (VI=4.8V, CI = CO =10µF, TA = -40 to 125°C, unless otherwise specified.) Symbol VO ∆VO ∆VO Vd Iq Isc Parameter Output Voltage Line Regulation Load Regulation Dropout Voltage Quiescent Current Short Circuit Current Termal Regulation SVR eN S S Supply Voltage Rejection RMS Output Noise Voltage (% of VO) Temperature Stability Long Term Stability IO = 0 mA IO = 0 mA IO = 0 mA Test Conditions TJ = 25°C VI = 3.4 to 18V VI = 3.4 to 15V TJ = 25°C IO = 0 to 5A VI = 3.4 to 30V (note 1) Min. 1.782 1.764 Typ. 1.8 1.8 0.5 0.1 3 7 1.3 5 5.5 0.5 60 6.5 0.7 0.003 75 0.003 0.5 0.5 0.015 Max. 1.818 1.836 6 6 15 20 1.5 10 Unit V V mV mV mV V V mA A A %/W dB % % % IO = 0 to 5A TJ = 25°C IO = 0 to 5A IO =5 A VI ≤ 30V VI - VO = 5V VI - VO = 25V TA = 25°C, 30ms pulse f = 120 Hz, CO = 25 µF, IO = 5A VI = 6.8 ± 3V TA = 25°C f =10Hz to 10KHz TA = 125°C 1000Hrs NOTE 1: See short-circuit current curve for available output current at fixed dropout. ELECTRICAL CHARACTERISTICS OF LD1084#25 (VI=5.5V, CI = CO =10µF, TA = -40 to 125°C, unless otherwise specified.) Symbol VO ∆VO ∆VO Vd Iq Isc Parameter Output Voltage Line Regulation Load Regulation Dropout Voltage Quiescent Current Short Circuit Current Termal Regulation SVR eN S S Supply Voltage Rejection RMS Output Noise Voltage (% of VO) Temperature Stability Long Term Stability IO = 0 mA Test Conditions TJ = 25°C IO = 0 to 5A VI = 4.1 to 30V (note 1) IO = 0 mA VI = 4.1 to 18V TJ = 25°C IO = 0 mA IO = 0 to 5A IO =5 A VI ≤ 30V VI - VO = 5V VI - VO = 25V TA = 25°C, 30ms pulse f = 120 Hz, CO = 25 µF, IO = 5A VI = 7.5 ± 3V TA = 25°C f =10Hz to 10KHz 60 5.5 0.5 VI = 4.1 to 18V IO = 0 to 5A TJ = 25°C Min. 2.475 2.45 Typ. 2.5 2.5 0.5 0.1 3 7 1.3 5 6.5 0.7 0.003 72 0.003 0.5 0.5 0.015 Max. 2.525 2.55 6 6 15 20 1.5 10 Unit V V mV mV mV V V mA A A %/W dB % % % TA = 125°C 1000Hrs NOTE 1: See short-circuit current curve for available output current at fixed dropout. 4/18 LD1084 SERIES ELECTRICAL CHARACTERISTICS OF LD1084#285 (VI=5.85V, CI = CO =10µF, TA = -40 to 125°C, unless otherwise specified.) Symbol VO ∆VO ∆VO Vd Iq Isc Parameter Output Voltage Line Regulation Load Regulation Dropout Voltage Quiescent Current Short Circuit Current Termal Regulation SVR eN S S Supply Voltage Rejection RMS Output Noise Voltage (% of VO) Temperature Stability Long Term Stability IO = 0 mA Test Conditions TJ = 25°C IO = 0 to 5A VI = 4.5 to 30V (note 1) IO = 0 mA VI = 4.5 to 18V TJ = 25°C IO = 0 mA IO = 0 to 5A IO =5 A VI ≤ 30V VI - VO = 5V VI - VO = 25V TA = 25°C, 30ms pulse f = 120 Hz, CO = 25 µF, IO = 5A VI = 7.85 ± 3V TA = 25°C f =10Hz to 10KHz 60 5.5 0.5 VI = 4.5 to 18V IO = 0 to 5A TJ = 25°C Min. 2.821 2.793 Typ. 2.85 2.85 0.5 0.1 3 7 1.3 5 6.5 0.7 0.003 72 0.003 0.5 0.5 0.015 Max. 2.879 2.907 6 6 15 20 1.5 10 Unit V V mV mV mV V V mA A A %/W dB % % % TA = 125°C 1000Hrs NOTE 1: See short-circuit current curve for available output current at fixed dropout. ELECTRICAL CHARACTERISTICS OF LD1084#33 (VI=6.3V, CI = CO =10µF, TA = -40 to 125°C, unless otherwise specified.) Symbol VO ∆VO ∆VO Vd Iq Isc Parameter Output Voltage Line Regulation Load Regulation Dropout Voltage Quiescent Current Short Circuit Current Termal Regulation SVR eN S S Supply Voltage Rejection RMS Output Noise Voltage (% of VO) Temperature Stability Long Term Stability IO = 0 mA Test Conditions TJ = 25°C IO = 0 to 5A VI = 4.9 to 30V (note 1) IO = 0 mA VI = 4.9 to 18V TJ = 25°C IO = 0 mA IO = 0 to 5A IO =5 A VI ≤ 30V VI - VO = 5V VI - VO = 25V TA = 25°C, 30ms pulse f = 120 Hz, CO = 25 µF, IO = 5A VI = 8.3 ± 3V TA = 25°C f =10Hz to 10KHz 60 5.5 0.5 VI = 4.9 to 18V IO = 0 to 5A TJ = 25°C Min. 3.267 3.234 Typ. 3.3 3.35 0.5 0.1 3 7 1.3 5 6.5 0.7 0.003 72 0.003 0.5 0.5 0.015 Max. 3.333 3.366 6 6 15 20 1.5 10 Unit V V mV mV mV V V mA A A %/W dB % % % TA = 125°C 1000Hrs NOTE 1: See short-circuit current curve for available output current at fixed dropout. 5/18 LD1084 SERIES ELECTRICAL CHARACTERISTICS OF LD1084#36 (VI=6.6V, CI = CO =10µF, TA = -40 to 125°C, unless otherwise specified.) Symbol VO ∆VO ∆VO Vd Iq Isc Parameter Output Voltage Line Regulation Load Regulation Dropout Voltage Quiescent Current Short Circuit Current Termal Regulation SVR eN S S Supply Voltage Rejection RMS Output Noise Voltage (% of VO) Temperature Stability Long Term Stability IO = 0 mA Test Conditions TJ = 25°C IO = 0 to 5A VI = 5.2 to 30V (note 1) IO = 0 mA VI = 5.2 to 18V TJ = 25°C IO = 0 mA IO = 0 to 5A IO =5 A VI ≤ 30V VI - VO = 5V VI - VO = 25V TA = 25°C, 30ms pulse f = 120 Hz, CO = 25 µF, IO = 5A VI = 8.6 ± 3V TA = 25°C f =10Hz to 10KHz 60 5.5 0.5 VI = 5.2 to 18V IO = 0 to 5A TJ = 25°C Min. 3.564 3.528 Typ. 3.6 3.6 0.5 0.1 3 7 1.3 5 6.5 0.7 0.003 72 0.003 0.5 0.5 0.015 Max. 3.636 3.672 10 10 15 20 1.5 10 Unit V V mV mV mV V V mA A A %/W dB % % % TA = 125°C 1000Hrs NOTE 1: See short-circuit current curve for available output current at fixed dropout. ELECTRICAL CHARACTERISTICS OF LD1084#5 (VI=8V, CI = CO =10µF, TA = -40 to 125°C, unless otherwise specified.) Symbol VO ∆VO ∆VO Vd Iq Isc Parameter Output Voltage Line Regulation Load Regulation Dropout Voltage Quiescent Current Short Circuit Current Termal Regulation SVR eN S S Supply Voltage Rejection RMS Output Noise Voltage (% of VO) Temperature Stability Long Term Stability IO = 0 mA IO = 0 mA IO = 0 mA Test Conditions TJ = 25°C VI = 6.6 to 20V VI = 6.6 to 20V TJ = 25°C IO = 0 to 5A VI = 6.6 to 30V (note 1) Min. 4.95 4.9 Typ. 5 5 0.5 1 5 10 1.3 5 5.5 0.5 60 6.5 0.7 0.003 72 0.003 0.5 0.5 0.015 Max. 5.05 5.1 10 10 20 35 1.5 10 Unit V V mV mV mV V V mA A A %/W dB % % % IO = 0 to 5A TJ = 25°C IO = 0 to 5A IO =5 A VI ≤ 30V VI - VO = 5V VI - VO = 25V TA = 25°C, 30ms pulse f = 120 Hz, CO = 25 µF, IO = 5A VI = 10 ± 3V TA = 25°C f =10Hz to 10KHz TA = 125°C 1000Hrs NOTE 1: See short-circuit current curve for available output current at fixed dropout. 6/18 LD1084 SERIES ELECTRICAL CHARACTERISTICS OF LD1084#8 (VI=11V, CI = CO =10µF, TA = -40 to 125°C, unless otherwise specified.) Symbol VO ∆VO ∆VO Vd Iq Isc Parameter Output Voltage Line Regulation Load Regulation Dropout Voltage Quiescent Current Short Circuit Current Termal Regulation SVR eN S S Supply Voltage Rejection RMS Output Noise Voltage (% of VO) Temperature Stability Long Term Stability IO = 0 mA Test Conditions TJ = 25°C IO = 0 to 5A VI = 9.6 to 30V (note 1) IO = 0 mA VI = 9.6 to 20V TJ = 25°C IO = 0 mA IO = 0 to 5A IO =5 A VI ≤ 30V VI - VO = 5V VI - VO = 25V TA = 25°C, 30ms pulse f = 120 Hz, CO = 25 µF, IO = 5A VI = 13 ± 3V TA = 25°C f =10Hz to 10KHz 54 5.5 0.5 VI = 9.6 to 20V IO = 0 to 5A TJ = 25°C Min. 7.92 7.84 Typ. 8 8 1 2 8 12 1.3 5 6.5 0.7 0.003 71 0.003 0.5 0.5 0.015 Max. 8.08 8.16 18 18 30 60 1.5 10 Unit V V mV mV mV V V mA A A %/W dB % % % TA = 125°C 1000Hrs NOTE 1: See short-circuit current curve for available output current at fixed dropout. ELECTRICAL CHARACTERISTICS OF LD1084#9 (VI=12V, CI = CO =10µF, TA = -40 to 125°C, unless otherwise specified.) Symbol VO ∆VO ∆VO Vd Iq Isc Parameter Output Voltage Line Regulation Load Regulation Dropout Voltage Quiescent Current Short Circuit Current Termal Regulation SVR eN S S Supply Voltage Rejection RMS Output Noise Voltage (% of VO) Temperature Stability Long Term Stability IO = 0 mA Test Conditions TJ = 25°C IO = 0 to 5A VI = 10.6 to 30V (note 1) IO = 0 mA VI = 10.6 to 20V TJ = 25°C IO = 0 mA IO = 0 to 5A IO =5 A VI ≤ 30V VI - VO = 5V VI - VO = 25V TA = 25°C, 30ms pulse f = 120 Hz, CO = 25 µF, IO = 5A VI = 14 ± 3V TA = 25°C f =10Hz to 10KHz 54 5.5 0.5 VI = 10.6 to 20V IO = 0 to 5A TJ = 25°C Min. 8.91 8.82 Typ. 9 9 1 2 8 12 1.3 5 6.5 0.7 0.003 70 0.003 0.5 0.5 0.015 Max. 9.09 9.18 20 20 30 60 1.5 10 Unit V V mV mV mV V V mA A A %/W dB % % % TA = 125°C 1000Hrs NOTE 1: See short-circuit current curve for available output current at fixed dropout. 7/18 LD1084 SERIES ELECTRICAL CHARACTERISTICS OF LD1084#120 (VI=15V, CI = CO =10µF, TA = -40 to 125°C, unless otherwise specified.) Symbol VO ∆VO ∆VO Vd Iq Isc Parameter Output Voltage Line Regulation Load Regulation Dropout Voltage Quiescent Current Short Circuit Current Termal Regulation SVR eN S S Supply Voltage Rejection RMS Output Noise Voltage (% of VO) Temperature Stability Long Term Stability IO = 0 mA Test Conditions TJ = 25°C IO = 0 to 5A VI = 13.6 to 30V (note 1) IO = 0 mA VI = 13.6 to 25V TJ = 25°C IO = 0 mA IO = 0 to 5A IO =5 A VI ≤ 30V VI - VO = 5V VI - VO = 25V TA = 25°C, 30ms pulse f = 120 Hz, CO = 25 µF, IO = 5A VI = 17 ± 3V TA = 25°C f =10Hz to 10KHz 54 5.5 0.5 VI = 13.6 to 25V IO = 0 to 5A TJ = 25°C Min. 11.88 11.76 Typ. 12 12 2 4 12 24 1.3 5 6.5 0.7 0.003 66 0.003 0.5 0.5 0.015 Max. 12.12 12.24 25 25 36 72 1.5 10 Unit V V mV mV mV V V mA A A %/W dB % % % TA = 125°C 1000Hrs NOTE 1: See short-circuit current curve for available output current at fixed dropout. ELECTRICAL CHARACTERISTICS OF LD1084 (VI=4.25V, CI = C O =10µF, TA = -40 to 125°C, unless otherwise specified.) Symbol VO Parameter Output Voltage IO = 10mA Test Conditions TJ = 25°C VI = 2.85 to 30V IO = 10mA to 5A (note 1) IO = 10mA VI = 2.85 to 16.5V TJ = 25°C IO = 10mA ∆VO Vd IO(min) Isc Load Regulation Dropout Voltage Minimum Load Current Short Circuit Current Termal Regulation SVR IADJ ∆IADJ eN S S Supply Voltage Rejection Adjust Pin Current Adjust Pin Current Change RMS Output Noise Voltage (% of VO) Temperature Stability Long Term Stability VI = 2.85 to 16.5V TJ = 25°C IO = 10mA to 5A IO = 10mA to 5A IO = 5A VI = 30V VI - VO = 5V VI - VO = 25V TA = 25°C, 30ms pulse f = 120 Hz, IO = 5A VI = 4.25V CO = 25 µF, CADJ = 25 µF, VI = 6.25 ± 3V IO = 10 mA 60 5.5 0.5 Min. 1.237 1.225 Typ. 1.25 1.25 0.015 0.035 0.1 0.2 1.3 3 6.5 0.7 0.003 72 55 0.2 0.003 0.5 0.5 120 5 0.015 Max. 1.263 1.275 0.2 0.2 0.3 0.4 1.5 10 Unit V V % % % % V mA A A %/W dB µA µA % % % ∆VO Line Regulation IO = 10mA to 5A VI = 2.85 to 16.5V (note 1) TA = 25°C f =10Hz to 10KHz TA = 125°C 1000Hrs NOTE 1: See short-circuit current curve for available output current at fixed dropout. 8/18 LD1084 SERIES TYPICAL CHARACTERISTICS (unless otherwise specified Tj = 25°C, CI=10µF (tant.), CO=22µF (tant.) Figure 1 : Short Circuit Current vs Dropout Voltage Figure 4 : Output Voltage vs Temperature Figure 2 : Line Regulation vs Temperature Figure 5 : Load Regulation vs Temperature Figure 3 : Quiescent Current vs Temperature Figure 6 : Quiescent Current vs Output Voltage 9/18 LD1084 SERIES Figure 7 : Quiescent Current vs Input Voltage Figure 10 : Dropout Voltage vs Temperature Figure 8 : Dropout Voltage vs Output Current Figure 11 : Supply Voltage Rejection vs Temperature Figure 9 : Supply Voltage Rejection vs Output Current Figure 12 : Supply Voltage Rejection vs Frequency 10/18 LD1084 SERIES Figure 13 : Adjust Pin Current vs Output Current Figure 16 : Adjust Pin Current vs Temperature Figure 14 : Reference Voltage vs Temperature Figure 17 : Line Regulation vs Temperature Figure 15 : Load Regulation vs Temperature Figure 18 : Minimum Load Currennt vs Temperature 11/18 LD1084 SERIES Figure 19 : Supply Voltage Rejection vs Temperature Figure 22 : Supply Voltage Rejection vs Output Current Figure 20 : Supply Voltage Rejection vs Frequency Figure 23 : Stability Figure 21 : Stability Figure 24 : Line Transient VI=14 to 15V, IO=200mA,CI = 1µF(tant), CO=10µF(tant), ts=tf=5µs 12/18 LD1084 SERIES Figure 25 : Line Transient Figure 28 : Line Transient VI=12 to 13V, IO=200mA, CI = 1µF(tant), CO=10µF(tant), No CADJ ts=tf=5µs VI=12 to 13V, IO=200mA, CI = 1µF(tant), CO=10µF(tant), CADJ = 1µF ts=tf=5µs Figure 26 : Load Transient Figure 29 : Load Transient VI=15 V, I O=0.1 to 5 A, CI = 1µF(tant), CO=10µF(tant) VI=13 V, I O=0.1 to 5 A, CI = 1µF(tant), CO=10µF(tant) Figure 27 : Load Transient VI=15 V, I O=0.1 to 5 A, CI = 1µF(tant), CO=10µF(tant), No CADJ 13/18 LD1084 SERIES TO-220 MECHANICAL DATA DIM. A C D D1 E F F1 F2 G G1 H2 L2 L4 L5 L6 L7 L9 DIA. 13.0 2.65 15.25 6.2 3.5 3.75 0.49 0.61 1.14 1.14 4.95 2.4 10.0 16.4 14.0 2.95 15.75 6.6 3.93 3.85 0.511 0.104 0.600 0.244 0.137 0.147 mm. MIN. 4.40 1.23 2.40 1.27 0.70 0.88 1.70 1.70 5.15 2.7 10.40 0.019 0.024 0.044 0.044 0.194 0.094 0.393 0.645 0.551 0.116 0.620 0.260 0.154 0.151 TYP MAX. 4.60 1.32 2.72 MIN. 0.173 0.048 0.094 0.050 0.027 0.034 0.067 0.067 0.203 0.106 0.409 inch TYP. MAX. 0.181 0.051 0.107 P011C 14/18 LD1084 SERIES D2PAK MECHANICAL DATA mm. DIM. MIN. A A1 A2 B B2 C C2 D D1 E E1 G L L2 L3 M R V2 0˚ 4.88 15 1.27 1.4 2.4 0.4 8˚ 0˚ 10 8.5 5.28 15.85 1.4 1.75 3.2 0.192 0.590 0.050 0.055 0.094 0.016 8˚ 4.4 2.49 0.03 0.7 1.14 0.45 1.23 8.95 8 10.4 0.393 0.335 0.208 0.624 0.055 0.068 0.126 TYP MAX. 4.6 2.69 0.23 0.93 1.7 0.6 1.36 9.35 MIN. 0.173 0.098 0.001 0.027 0.044 0.017 0.048 0.352 0.315 0.409 TYP. MAX. 0.181 0.106 0.009 0.036 0.067 0.023 0.053 0.368 inch P011P6G 15/18 LD1084 SERIES D2PAK/A MECHANICAL DATA mm. DIM. MIN. A A1 B B2 C C2 D E G L L2 4.40 2.49 0.7 1.14 0.45 1.21 8.95 10 4.88 15 1.27 TYP MAX. 4.60 2.69 0.93 1.7 0.60 1.36 9.35 10.4 5.28 15.85 1.4 MIN. 0.173 0.098 0.027 0.044 0.017 0.047 0.352 0.393 0.192 0.590 0.050 TYP. MAX. 0.181 0.106 0.036 0.067 0.023 0.053 0.368 0.409 0.208 0.106 0.055 inch 16/18 LD1084 SERIES Tape & Reel D2PAK-P 2PAK-D 2PAK/A-P 2PAK/A MECHANICAL DATA mm. DIM. MIN. A C D N T Ao Bo Ko Po P 10.50 15.70 4.80 3.9 11.9 10.6 15.80 4.90 4.0 12.0 12.8 20.2 60 14.4 10.70 15.90 5.00 4.1 12.1 0.413 0.618 0.189 0.153 0.468 0.417 0.622 0.193 0.157 0.472 13.0 TYP MAX. 180 13.2 0.504 0.795 2.362 0.567 0.421 0.626 0.197 0.161 0.476 0.512 MIN. TYP. MAX. 7.086 0.519 inch 17/18 LD1084 SERIES Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. © The ST logo is a registered trademark of STMicroelectronics © 2003 STMicroelectronics - Printed in Italy - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - Canada - China - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco Singapore - Spain - Sweden - Switzerland - United Kingdom - United States. © http://www.st.com 18/18