LD1117V25

LD1117 Adjustable and fixed low drop positive voltage regulator Datasheet - production data Description DPAK TO-220 SOT-223 SO-8 Features • Low dropout voltage (1 V typ.) • 2.85 V device performances are suitable for SCSI-2 active termination • Output current up to 800 mA • Fixed output voltage of: 1.2 V, 1.8 V, 2.5 V, 3.3 V, 5.0 V The LD1117 is a low drop voltage regulator able to provide up to 800 mA of output current, available even in adjustable version (VREF = 1.25 V). Concerning fixed versions, are offered the following output voltages: 1.2 V, 1.8 V, 2.5 V, 2.85 V, 3.3 V and 5.0 V. The device is supplied in: SOT-223, DPAK, SO-8 and TO-220. The SOT-223 and DPAK surface mount packages optimize the thermal characteristics even offering a relevant space saving effect. High efficiency is assured by NPN pass transistor. In fact in this case, unlike than PNP one, the quiescent current flows mostly into the load. Only a very common 10 µF minimum capacitor is needed for stability. On chip trimming allows the regulator to reach a very tight output voltage tolerance, within ± 1 % at 25 °C. The adjustable LD1117 is pin to pin compatible with the other standard. Adjustable voltage regulators maintaining the better performances in terms of drop and tolerance. • Adjustable version availability (VREF = 1.25 V) • Internal current and thermal limit • Available in ± 1 % (at 25 °C) and 2 % in full temperature range • Supply voltage rejection: 75 dB (typ.) February 2020 This is information on a product in full production. DocID2572 Rev 37 1/46 www.st.com 46 Contents LD1117 Contents 1 Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2 Pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 3 Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 4 Schematic application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 5 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 6 Typical application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 7 LD1117 adjustable: application note . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 8 Package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 9 Packaging mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 10 Order codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 11 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 2/46 DocID2572 Rev 37 LD1117 List of tables List of tables Table 1. Table 2. Table 3. Table 4. Table 5. Table 6. Table 7. Table 8. Table 9. Table 10. Table 11. Table 12. Table 13. Table 14. Table 15. Table 16. Table 17. Table 18. Table 19. Table 20. Table 21. Table 22. Table 23. Table 24. Table 25. Table 26. Table 27. Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Thermal data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Electrical characteristics of LD1117#12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Electrical characteristics of LD1117#18 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Electrical characteristics of LD1117#25 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Electrical characteristics of LD1117#33 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Electrical characteristics of LD1117#50 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Electrical characteristics of LD1117 (adjustable) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Electrical characteristics of LD1117#12C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Electrical characteristics of LD1117#18C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Electrical characteristics of LD1117#25C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Electrical characteristics of LD1117#33C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Electrical characteristics of LD1117#50C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Electrical characteristics of LD1117C (adjustable) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 TO-220 mechanical data (type STD-ST Dual Gauge) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 TO-220 mechanical data (type STD-ST Single Gauge) . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 SOT-223 mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 SO-8 mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 DPAK (TO-252) mechanical data (type A) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 DPAK (TO-252) mechanical data (type E) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 DPAK (TO-252) mechanical data type I . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Footprint data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 SOT-223 tape and reel mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 SO-8 tape and reel mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 DPAK tape and reel mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Order codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 DocID2572 Rev 37 3/46 List of figures LD1117 List of figures Figure 1. Figure 2. Figure 3. Figure 4. Figure 5. Figure 6. Figure 7. Figure 8. Figure 9. Figure 10. Figure 11. Figure 12. Figure 13. Figure 14. Figure 15. Figure 16. Figure 17. Figure 18. Figure 19. Figure 20. Figure 21. Figure 22. Figure 23. Figure 24. Figure 25. Figure 26. 4/46 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Pin connections (top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Application circuit (for 1.2 V) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Application circuit (for other fixed output voltages) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Negative supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Circuit for increasing output voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Voltage regulator with reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Battery backed-up regulated supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Post-regulated dual supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Adjustable output voltage application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Adjustable output voltage application with improved ripple rejection . . . . . . . . . . . . . . . . . 24 Drawing dimension TO-220 (type STD-ST Dual Gauge) . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Drawing dimension TO-220 (type STD-ST Single Gauge) . . . . . . . . . . . . . . . . . . . . . . . . . 28 Drawing dimension SOT-223 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Drawing dimension SO-8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 DPAK (TO-252) package outline A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 DPAK (TO-252) package outline E . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 DPAK (TO-252) package outline I . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 DPAK footprint recommended data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Drawing dimension tube for TO-220 Dual Gauge (mm.) . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Drawing dimension tube for TO-220 Single Gauge (mm.) . . . . . . . . . . . . . . . . . . . . . . . . . 38 Tape for SOT-223 (dimensions are in mm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Reel for SOT-223 (dimensions are in mm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 SO-8 tape and reel dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Tape for DPAK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Reel for DPAK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 DocID2572 Rev 37 LD1117 1 Diagram Diagram Figure 1. Block diagram DocID2572 Rev 37 5/46 Pin configuration 2 LD1117 Pin configuration Figure 2. Pin connections (top view) $'-*1'    9287 9287 9287 9287 $'-*1' 6/46  1&  9,1  9287  $'-*1' TO-220 DPAK Note:  SO-8 9,1   1& 9,1 SOT-223   9287 9,1 $'-*1' 9287  The TAB is connected to the VOUT. DocID2572 Rev 37 LD1117 3 Maximum ratings Maximum ratings Table 1. Absolute maximum ratings Symbol Parameter Value Unit VIN (1) DC input voltage 15 V PTOT Power dissipation 12 W TSTG Storage temperature range -40 to +150 °C TOP Operating junction temperature range -40 to +125 °C 0 to +125 °C for C version for standard version 1. Absolute maximum rating of VIN = 18 V, when IOUT is lower than 20 mA. Table 2. Thermal data Symbol Parameter SOT-223 SO-8 DPAK TO-220 Unit RthJC Thermal resistance junction-case 15 20 8 5 °C/W RthJA Thermal resistance junction-ambient 110 55 100 50 °C/W DocID2572 Rev 37 7/46 Schematic application 4 LD1117 Schematic application Figure 3. Application circuit (for 1.2 V) Figure 4. Application circuit (for other fixed output voltages) 8/46 DocID2572 Rev 37 LD1117 5 Electrical characteristics Electrical characteristics Refer to the test circuits, TJ = 0 to 125 °C, CO = 10 µF, R = 120 Ω between GND and OUT pins, unless otherwise specified. Table 3. Electrical characteristics of LD1117#12 Symbol Parameter Test condition Min. Typ. Max. Unit VO Output voltage Vin = 3.2 V, IO = 10 mA, TJ = 25 °C 1.188 1.20 1.212 V VO Output voltage IO = 10 to 800 mA Vin - VO = 1.4 to 10 V 1.140 1.20 1.260 V ∆VO Line regulation Vin - VO = 1.5 to 13.75 V, IO = 10 mA 0.035 0.2 % ∆VO Load regulation Vin - VO = 3 V, IO = 10 to 800 mA 0.1 0.4 % ∆VO Temperature stability ∆VO Long term stability 1000 hrs, TJ = 125 °C Vin Operating input voltage Iadj Adjustment pin current Vin ≤ 15 V Adjustment pin current change 0.5 % 0.3 % 15 V 60 120 µA Vin - VO = 1.4 to 10 V IO = 10 to 800 mA 1 5 µA Minimum load current Vin = 15 V 2 5 mA IO Output current Vin - VO = 5 V, TJ = 25 °C 950 1300 mA eN Output noise (%VO) B = 10 Hz to 10 kHz, TJ = 25 °C Supply voltage rejection IO = 40 mA, f = 120 Hz, TJ = 25 °C Vin - VO = 3 V, Vripple = 1 VPP ∆Iadj IO(min) SVR Vd Dropout voltage Thermal regulation 800 60 0.003 % 75 dB IO = 100 mA 1 1.1 IO = 500 mA 1.05 1.15 IO = 800 mA 1.10 1.2 Ta = 25 °C, 30 ms Pulse 0.01 0.1 DocID2572 Rev 37 V %/W 9/46 Electrical characteristics LD1117 Refer to the test circuits, TJ = 0 to 125 °C, CO = 10 µF, unless otherwise specified. Table 4. Electrical characteristics of LD1117#18 Symbol Parameter Test condition Min. Typ. Max. Unit 1.8 1.82 V 1.84 V VO Output voltage Vin = 3.8 V, IO = 10 mA, TJ = 25 °C 1.78 VO Output voltage IO = 0 to 800 mA, Vin = 3.3 to 8 V 1.76 ∆VO Line regulation Vin = 3.3 to 8 V, IO = 0 mA 1 6 mV ∆VO Load regulation Vin = 3.3 V, IO = 0 to 800 mA 1 10 mV ∆VO Temperature stability ∆VO Long term stability 1000 hrs, TJ = 125 °C Vin Operating input voltage IO = 100 mA Id Quiescent current Vin ≤ 8 V IO Output current Vin = 6.8 V, TJ = 25 °C eN Output noise voltage B = 10 Hz to 10 kHz, TJ = 25 °C Supply voltage rejection IO = 40 mA, f = 120 Hz, TJ = 25 °C Vin = 5.5 V, Vripple = 1 VPP SVR Vd Dropout voltage Thermal regulation 10/46 800 60 0.5 % 0.3 % 15 V 5 10 mA 950 1300 mA 100 µV 75 dB IO = 100 mA 1 1.1 IO = 500 mA 1.05 1.15 IO = 800 mA 1.10 1.2 Ta = 25 °C, 30 ms Pulse 0.01 0.1 DocID2572 Rev 37 V %/W LD1117 Electrical characteristics Refer to the test circuits, TJ = 0 to 125 °C, CO = 10 µF, unless otherwise specified. Table 5. Electrical characteristics of LD1117#25 Symbol Parameter Test condition Min. Typ. Max. Unit 2.5 2.525 V 2.55 V VO Output voltage Vin = 4.5 V, IO = 10 mA, TJ = 25 °C 2.475 VO Output voltage IO = 0 to 800 mA, Vin = 3.9 to 10 V 2.45 ∆VO Line regulation Vin = 3.9 to 10 V, IO = 0 mA 1 6 mV ∆VO Load regulation Vin = 3.9 V, IO = 0 to 800 mA 1 10 mV ∆VO Temperature stability ∆VO Long term stability 1000 hrs, TJ = 125 °C Vin Operating input voltage IO = 100 mA Id Quiescent current Vin ≤ 10 V IO Output current Vin = 7.5 V TJ = 25 °C eN Output noise voltage B = 10 Hz to 10 kHz, TJ = 25 °C Supply voltage rejection IO = 40 mA, f = 120 Hz, TJ = 25 °C Vin = 5.5 V, Vripple = 1 VPP SVR Vd Dropout voltage Thermal regulation 800 60 0.5 % 0.3 % 15 V 5 10 mA 950 1300 mA 100 µV 75 dB IO = 100 mA 1 1.1 IO = 500 mA 1.05 1.15 IO = 800 mA 1.10 1.2 Ta = 25 °C, 30 ms Pulse 0.01 0.1 DocID2572 Rev 37 V %/W 11/46 Electrical characteristics LD1117 Refer to the test circuits, TJ = 0 to 125 °C, CO = 10 µF, unless otherwise specified. Table 6. Electrical characteristics of LD1117#33 Symbol Parameter Test condition Min. Typ. Max. Unit 3.3 3.333 V 3.365 V VO Output voltage Vin = 5.3 V, IO = 10 mA, TJ = 25 °C 3.267 VO Output voltage IO = 0 to 800 mA, Vin = 4.75 to 10 V 3.235 ∆VO Line regulation Vin = 4.75 to 15 V, IO = 0 mA 1 6 mV ∆VO Load regulation Vin = 4.75 V, IO = 0 to 800 mA 1 10 mV ∆VO Temperature stability ∆VO Long term stability 1000 hrs, TJ = 125 °C Vin Operating input voltage IO = 100 mA Id Quiescent current Vin ≤ 15 V IO Output current Vin = 8.3 V, TJ = 25 °C eN Output noise voltage B = 10 Hz to 10 kHz, TJ = 25 °C Supply voltage rejection IO = 40 mA, f = 120 Hz, TJ = 25 °C Vin = 6.3 V, Vripple = 1 VPP SVR Vd Dropout voltage Thermal regulation 12/46 800 60 0.5 % 0.3 % 15 V 5 10 mA 950 1300 mA 100 µV 75 dB IO = 100 mA 1 1.1 IO = 500 mA 1.05 1.15 IO = 800 mA 1.10 1.2 Ta = 25 °C, 30 ms Pulse 0.01 0.1 DocID2572 Rev 37 V %/W LD1117 Electrical characteristics Refer to the test circuits, TJ = 0 to 125 °C, CO = 10 µF, unless otherwise specified. Table 7. Electrical characteristics of LD1117#50 Symbol Parameter Test condition Min. Typ. Max. Unit 5 5.05 V 5.1 V VO Output voltage Vin = 7 V, IO = 10 mA, TJ = 25 °C 4.95 VO Output voltage IO = 0 to 800 mA, Vin = 6.5 to 15 V 4.9 ∆VO Line regulation Vin = 6.5 to 15 V, IO = 0 mA 1 10 mV ∆VO Load regulation Vin = 6.5 V, IO = 0 to 800 mA 1 15 mV ∆VO Temperature stability ∆VO Long term stability 1000 hrs, TJ = 125 °C Vin Operating input voltage IO = 100 mA Id Quiescent current Vin ≤ 15 V IO Output current Vin = 10 V, TJ = 25 °C eN Output noise voltage B = 10 Hz to 10 kHz, TJ = 25 °C Supply voltage rejection IO = 40 mA, f = 120 Hz, TJ = 25 °C Vin = 8 V, Vripple = 1 VPP SVR Vd Dropout voltage Thermal regulation 800 60 0.5 % 0.3 % 15 V 5 10 mA 950 1300 mA 100 µV 75 dB IO = 100 mA 1 1.1 IO = 500 mA 1.05 1.15 IO = 800 mA 1.10 1.2 Ta = 25 °C, 30 ms Pulse 0.01 0.1 DocID2572 Rev 37 V %/W 13/46 Electrical characteristics LD1117 Refer to the test circuits, TJ = 0 to 125 °C, CO = 10 µF, unless otherwise specified. Table 8. Electrical characteristics of LD1117 (adjustable) Symbol Parameter Test condition Min. Typ. Max. Unit 1.238 1.25 1.262 V 1.275 V 0.035 0.2 % 0.1 0.4 % Vref Reference voltage Vin - VO = 2 V, IO = 10 mA, TJ = 25 °C Vref Reference voltage IO = 10 to 800 mA, Vin - VO = 1.4 to 10 V 1.225 ∆VO Line regulation Vin - VO = 1.5 to 13.75 V, IO = 10 mA ∆VO Load regulation Vin - VO = 3 V, IO = 10 to 800 mA ∆VO Temperature stability ∆VO Long term stability Vin Operating input voltage Iadj Adjustment pin current 1000 hrs, TJ = 125 °C 0.5 % 0.3 % 15 V 60 120 µA Adjustment pin current change Vin - VO = 1.4 to 10 V, IO = 10 to 800 mA 1 5 µA Minimum load current Vin = 15 V 2 5 mA IO Output current Vin - VO = 5 V, TJ = 25 °C 950 1300 mA eN Output noise (%VO) B = 10 Hz to 10 kHz, TJ = 25 °C Supply voltage rejection IO = 40 mA, f = 120 Hz, TJ = 25 °C Vin - VO = 3 V, Vripple = 1 VPP ∆Iadj IO(min) SVR Vd Dropout voltage Thermal regulation 14/46 Vin ≤ 15 V 800 60 0.003 % 75 dB IO = 100 mA 1 1.1 IO = 500 mA 1.05 1.15 IO = 800 mA 1.10 1.2 Ta = 25 °C, 30 ms Pulse 0.01 0.1 DocID2572 Rev 37 V %/W LD1117 Electrical characteristics Refer to the test circuits, TJ = -40 to 125 °C, CO = 10 µF, R = 120 Ω between GND and OUT pins, unless otherwise specified. Table 9. Electrical characteristics of LD1117#12C Symbol Parameter Test condition Min. Typ. Max. Unit VO Output voltage Vin - VO = 2 V, IO = 10 mA, TJ = 25 °C 1.176 1.20 1.224 V VO Output voltage IO = 10 to 800 mA, Vin - VO = 1.4 to 10 V 1.120 1.20 1.280 V ∆VO Line regulation Vin - VO = 1.5 to 13.75 V, IO = 10 mA 1 % ∆VO Load regulation Vin - VO = 3 V, IO = 10 to 800 mA 1 % ∆VO Temperature stability ∆VO Long term stability 1000 hrs, TJ = 125 °C Vin Operating input voltage Iadj Adjustment pin current Vin ≤ 15 V ∆Iadj Adjustment pin current change IO(min) 0.5 % 0.3 % 15 V 60 120 µA Vin - VO = 1.4 to 10 V IO = 10 to 800 mA 1 5 µA Minimum load current Vin = 15 V 2 5 mA IO Output current Vin - VO = 5 V, TJ = 25 °C 950 1300 mA eN Output noise (%VO) B = 10 Hz to 10 kHz, TJ = 25 °C Supply voltage rejection IO = 40 mA, f = 120 Hz, TJ = 25 °C Vin - VO = 3 V, Vripple = 1 VPP SVR Vd Dropout voltage Thermal regulation 800 60 0.003 % 75 dB IO = 100 mA, TJ = 0 to 125 °C 1 1.1 IO = 500 mA, TJ = 0 to 125 °C 1.05 1.2 IO = 800 mA, TJ = 0 to 125 °C 1.10 1.3 Ta = 25 °C, 30 ms Pulse 0.01 0.1 DocID2572 Rev 37 V %/W 15/46 Electrical characteristics LD1117 Refer to the test circuits, TJ = -40 to 125 °C, CO = 10 µF, unless otherwise specified. Table 10. Electrical characteristics of LD1117#18C Symbol Parameter Test condition Min. Typ. Max. Unit 1.8 1.84 V 1.87 V VO Output voltage Vin = 3.8 V, IO = 10 mA, TJ = 25 °C 1.76 VO Output voltage IO = 0 to 800 mA, Vin = 3.9 to 10 V 1.73 ∆VO Line regulation Vin = 3.3 to 8 V, IO = 0 mA 1 30 mV ∆VO Load regulation Vin = 3.3 V, IO = 0 to 800 mA 1 30 mV ∆VO Temperature stability ∆VO Long term stability 1000 hrs, TJ = 125 °C Vin Operating input voltage IO = 100 mA Id Quiescent current Vin ≤ 8 V IO Output current Vin = 6.8 V TJ = 25 °C eN Output noise voltage B = 10 Hz to 10 kHz, TJ = 25 °C Supply voltage rejection IO = 40 mA, f = 120 Hz, TJ = 25 °C Vin = 5.5 V, Vripple = 1 VPP SVR Vd Vd Dropout voltage Dropout voltage Thermal regulation 16/46 800 60 0.5 % 0.3 % 15 V 5 10 mA 950 1300 mA 100 µV 75 dB IO = 100 mA, TJ = 0 to 125 °C 1 1.1 IO = 500 mA, TJ = 0 to 125 °C 1.05 1.15 IO = 800 mA, TJ = 0 to 125 °C 1.10 1.2 IO = 100 mA 1.1 IO = 500 mA 1.2 IO = 800 mA 1.3 Ta = 25 °C, 30 ms Pulse DocID2572 Rev 37 0.01 0.1 V V %/W LD1117 Electrical characteristics Refer to the test circuits, TJ = -40 to 125 °C, CO = 10 µF, unless otherwise specified. Table 11. Electrical characteristics of LD1117#25C Symbol Parameter Test condition Min. Typ. Max. Unit 2.5 2.55 V 2.6 V VO Output voltage Vin = 4.5 V, IO = 10 mA, TJ = 25 °C 2.45 VO Output voltage IO = 0 to 800 mA, Vin = 3.9 to 10 V 2.4 ∆VO Line regulation Vin = 3.9 to 10 V, IO = 0 mA 1 30 mV ∆VO Load regulation Vin = 3.9 V, IO = 0 to 800 mA 1 30 mV ∆VO Temperature stability ∆VO Long term stability 1000 hrs, TJ = 125 °C Vin Operating input voltage IO = 100 mA Id Quiescent current Vin ≤ 10 V IO Output current Vin = 7.5 V TJ = 25 °C eN Output noise voltage B = 10 Hz to 10 kHz, TJ = 25 °C Supply voltage rejection IO = 40 mA, f = 120 Hz, TJ = 25 °C Vin = 5.5 V, Vripple = 1 VPP SVR Vd Vd Dropout voltage Dropout voltage Thermal regulation 800 60 0.5 % 0.3 % 15 V 5 10 mA 950 1300 mA 100 µV 75 dB IO = 100 mA, TJ = 0 to 125 °C 1 1.1 IO = 500 mA, TJ = 0 to 125 °C 1.05 1.15 IO = 800 mA, TJ = 0 to 125 °C 1.10 1.2 IO = 100 mA 1.1 IO = 500 mA 1.2 IO = 800 mA 1.3 Ta = 25 °C, 30 ms Pulse DocID2572 Rev 37 0.01 0.1 V V %/W 17/46 Electrical characteristics LD1117 Refer to the test circuits, TJ = -40 to 125 °C, CO = 10 µF, unless otherwise specified. Table 12. Electrical characteristics of LD1117#33C Symbol Parameter Test condition Min. Typ. Max. Unit 3.3 3.36 V 3.44 V VO Output voltage Vin = 5.3 V, IO = 10 mA, TJ = 25 °C 3.24 VO Output voltage IO = 0 to 800 mA, Vin = 4.75 to 10 V 3.16 ∆VO Line regulation Vin = 4.75 to 15 V, IO = 0 mA 1 30 mV ∆VO Load regulation Vin = 4.75 V, IO = 0 to 800 mA 1 30 mV ∆VO Temperature stability ∆VO Long term stability 1000 hrs, TJ = 125 °C Vin Operating input voltage IO = 100 mA Id Quiescent current Vin ≤ 15 V IO Output current Vin = 8.3 V, TJ = 25 °C eN Output noise voltage B = 10 Hz to 10 kHz, TJ = 25 °C Supply voltage rejection IO = 40 mA, f = 120 Hz, TJ = 25 °C Vin = 6.3 V, Vripple = 1 VPP SVR Vd Vd Dropout voltage Dropout voltage Thermal regulation 18/46 800 60 0.5 % 0.3 % 15 V 5 10 mA 950 1300 mA 100 µV 75 dB IO = 100 mA, TJ = 0 to 125 °C 1 1.1 IO = 500 mA, TJ = 0 to 125 °C 1.05 1.15 IO = 800 mA, TJ = 0 to 125 °C 1.10 1.2 IO = 100 mA 1.1 IO = 500 mA 1.2 IO = 800 mA 1.3 Ta = 25 °C, 30 ms Pulse DocID2572 Rev 37 0.01 0.1 V V %/W LD1117 Electrical characteristics Refer to the test circuits, TJ = -40 to 125 °C, CO = 10 µF, unless otherwise specified. Table 13. Electrical characteristics of LD1117#50C Symbol Parameter Test condition Min. Typ. Max. Unit 5 5.1 V 5.2 V VO Output voltage Vin = 7 V, IO = 10 mA, TJ = 25 °C 4.9 VO Output voltage IO = 0 to 800 mA, Vin = 6.5 to 15 V 4.8 ∆VO Line regulation Vin = 6.5 to 15 V, IO = 0 mA 1 50 mV ∆VO Load regulation Vin = 6.5 V, IO = 0 to 800 mA 1 50 mV ∆VO Temperature stability ∆VO Long term stability 1000 hrs, TJ = 125 °C Vin Operating input voltage IO = 100 mA Id Quiescent current Vin ≤ 15 V IO Output current Vin = 10 V, TJ = 25 °C eN Output noise voltage B = 10 Hz to 10 kHz, TJ = 25 °C Supply voltage rejection IO = 40 mA, f = 120 Hz, TJ = 25 °C Vin = 8 V, Vripple = 1 VPP SVR Vd Vd Dropout voltage Dropout voltage Thermal regulation 800 60 0.5 % 0.3 % 15 V 5 10 mA 950 1300 mA 100 µV 75 dB IO = 100 mA, TJ = 0 to 125 °C 1 1.1 IO = 500 mA, TJ = 0 to 125 °C 1.05 1.15 IO = 800 mA, TJ = 0 to 125 °C 1.10 1.2 IO = 100 mA 1.1 IO = 500 mA 1.2 IO = 800 mA 1.3 Ta = 25 °C, 30 ms Pulse DocID2572 Rev 37 0.01 0.1 V V %/W 19/46 Electrical characteristics LD1117 Refer to the test circuits, TJ = -40 to 125 °C, CO = 10 µF, unless otherwise specified. Table 14. Electrical characteristics of LD1117C (adjustable) Symbol Parameter Test condition Min. Typ. Max. Unit 1.225 1.25 1.275 V 1.3 V Vref Reference voltage Vin - VO = 2 V, IO = 10 mA, TJ = 25 °C Vref Reference voltage IO = 10 to 800 mA, Vin - VO= 1.4 to 10 V ∆VO Line regulation Vin - VO = 1.5 to 13.75 V, IO = 10 mA 1 % ∆VO Load regulation Vin - VO = 3 V, IO = 10 to 800 mA 1 % ∆VO Temperature stability ∆VO Long term stability Vin Operating input voltage Iadj Adjustment pin current 1.2 1000 hrs, TJ = 125 °C 0.5 % 0.3 % 15 V 60 120 µA Adjustment pin current change Vin - VO = 1.4 to 10 V, IO = 10 to 800 mA 1 10 µA Minimum load current Vin = 15 V 2 5 mA IO Output current Vin - VO = 5 V, TJ = 25 °C 950 1300 mA eN Output noise (%VO) B = 10 Hz to 10 kHz, TJ = 25 °C Supply voltage rejection IO = 40 mA, f = 120 Hz, TJ = 25 °C Vin - VO = 3 V, Vripple = 1 VPP ∆Iadj IO(min) SVR Vd Vd Dropout voltage Dropout voltage Thermal regulation 20/46 Vin ≤ 15 V 800 60 0.003 % 75 dB IO = 100 mA, TJ = 0 to 125 °C 1 1.1 IO = 500 mA, TJ = 0 to 125 °C 1.05 1.15 IO = 800 mA, TJ = 0 to 125 °C 1.10 1.2 IO = 100 mA 1.1 IO = 500 mA 1.2 IO = 800 mA 1.3 Ta = 25 °C, 30 ms Pulse DocID2572 Rev 37 0.01 0.1 V V %/W LD1117 6 Typical application Typical application Figure 5. Negative supply Figure 6. Circuit for increasing output voltage Figure 7. Voltage regulator with reference DocID2572 Rev 37 21/46 Typical application LD1117 Figure 8. Battery backed-up regulated supply 22/46 DocID2572 Rev 37 LD1117 Typical application Figure 9. Post-regulated dual supply DocID2572 Rev 37 23/46 LD1117 adjustable: application note 7 LD1117 LD1117 adjustable: application note The LD1117 adjustable has a thermal stabilized 1.25 ± 0.012 V reference voltage between the OUT and ADJ pins. IADJ is 60 µA typ. (120 µA max.) and ∆IADJ is 1 µA typ. (5 µA max.). R1 is normally fixed to 120 Ω. From Figure 9 we obtain: VOUT = VREF + R2 (IADJ +IR1) = VREF + R2 (IADJ +VREF /R1) = VREF (1 + R2 / R1) + R2 x IADJ. In normal application R2 value is in the range of few kΩ, so the R2 x IADJ product could not be considered in the VOUT calculation; then the above expression becomes: VOUT = VREF (1 + R2 / R1). In order to have the better load regulation it is important to realize a good Kelvin connection of R1 and R2 resistors. In particular R1 connection must be realized very close to OUT and ADJ pin, while R2 ground connection must be placed as near as possible to the negative Load pin. Ripple rejection can be improved by introducing a 10 µF electrolytic capacitor placed in parallel to the R2 resistor (see Figure 10). Figure 10. Adjustable output voltage application Figure 11. Adjustable output voltage application with improved ripple rejection 24/46 DocID2572 Rev 37 LD1117 8 Package information Package information In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK packages, depending on their level of environmental compliance. ECOPACK specifications, grade definitions and product status are available at: www.st.com. ECOPACK is an ST trademark. Table 15. TO-220 mechanical data (type STD-ST Dual Gauge) mm Dim. Min. Typ. Max. A 4.40 4.60 b 0.61 0.88 b1 1.14 1.70 c 0.48 0.70 D 15.25 15.75 D1 1.27 E 10 10.40 e 2.40 2.70 e1 4.95 5.15 F 1.23 1.32 H1 6.20 6.60 J1 2.40 2.72 L 13 14 L1 3.50 3.93 L20 16.40 L30 28.90 ∅P 3.75 3.85 Q 2.65 2.95 DocID2572 Rev 37 25/46 Package information LD1117 Figure 12. Drawing dimension TO-220 (type STD-ST Dual Gauge) BW\SH$B5HYB7 26/46 DocID2572 Rev 37 LD1117 Package information Table 16. TO-220 mechanical data (type STD-ST Single Gauge) mm Dim. Min. Typ. Max. A 4.40 4.60 b 0.61 0.88 b1 1.14 1.70 c 0.48 0.70 D 15.25 15.75 E 10 10.40 e 2.40 2.70 e1 4.95 5.15 F 0.51 0.60 H1 6.20 6.60 J1 2.40 2.72 L 13 14 L1 3.50 3.93 L20 16.40 L30 28.90 ∅P 3.75 3.85 Q 2.65 2.95 DocID2572 Rev 37 27/46 Package information LD1117 Figure 13. Drawing dimension TO-220 (type STD-ST Single Gauge) BUHY' 28/46 DocID2572 Rev 37 LD1117 Package information Table 17. SOT-223 mechanical data mm Dim. Min. Typ. A Max. 1.80 A1 0.02 0.10 B 0.60 0.70 0.85 B1 2.90 3.00 3.15 c 0.24 0.26 0.35 D 6.30 6.50 6.70 e 2.30 e1 4.60 E 3.30 3.50 3.70 H 6.70 7.00 7.30 V 10° Figure 14. Drawing dimension SOT-223 DocID2572 Rev 37 29/46 Package information LD1117 Table 18. SO-8 mechanical data mm Dim. Min. Typ. A Max. 1.75 A1 0.10 0.25 A2 1.25 b 0.28 0.48 c 0.17 0.23 D 4.80 4.90 5.00 E 5.80 6.00 6.20 E1 3.80 3.90 4.00 e 1.27 h 0.25 0.50 L 0.40 1.27 L1 k 1.04 0° 8° ccc 0.10 Figure 15. Drawing dimension SO-8 0016023_Rev_G 30/46 DocID2572 Rev 37 LD1117 Package information Table 19. DPAK (TO-252) mechanical data (type A) mm Dim. Min. Typ. Max. A 2.20 2.40 A1 0.90 1.10 A2 0.03 0.23 b 0.64 0.90 b4 5.20 5.40 c 0.45 0.60 c2 0.48 0.60 D 6.00 6.20 D1 4.95 E 6.40 E1 4.60 4.70 4.80 e 2.159 2.286 2.143 e1 4.445 4.572 4.699 H 9.35 10.10 L 1.00 1.50 L1 2.60 5.10 6.60 2.80 L2 L4 1.50 3.00 0.60 R V2 5.25 1.00 0.20 0° DocID2572 Rev 37 8° 31/46 Package information LD1117 Figure 16. DPAK (TO-252) package outline A 32/46 DocID2572 Rev 37 LD1117 Package information Table 20. DPAK (TO-252) mechanical data (type E) mm Dim. Min. A Typ. 2.18 Max. 2.39 A2 0.13 b 0.65 0.884 b4 4.95 5.46 c 0.46 0.61 c2 0.46 0.60 D 5.97 6.22 D1 5.21 E 6.35 E1 4.32 6.73 e 2.286 e1 4.572 H 9.94 10.34 L 1.50 1.78 L1 L2 2.74 0.89 L4 1.27 1.02 DocID2572 Rev 37 33/46 Package information LD1117 Figure 17. DPAK (TO-252) package outline E 34/46 DocID2572 Rev 37 LD1117 Package information Table 21. DPAK (TO-252) mechanical data type I mm Dim. Min. Typ. Max. A 2.20 2.30 2.38 A1 0.90 1.01 1.10 A2 0.00 - 0.10 b 0.77 - 0.89 b1 0.76 0.81 0.86 b2 0.77 - 1.10 b3 5.23 5.33 5.43 c 0.47 - 0.60 c1 0.46 0.51 0.56 c2 0.47 - 0.60 D 6.00 6.10 6.20 D1 5.25 5.40 5.60 E 6.50 6.60 6.70 E1 4.70 4.85 5.00 e 2.286 BSC H 9.80 10.10 10.40 L 1.40 1.50 1.70 L1 L2 2.90 REF 0.90 L3 - 1.25 0.51 BSC L4 0.60 0.80 1.00 L5 0.90 - 1.50 L6 1.80 BSC Θ 0° - 8° Θ1 3° 5° 7° Θ2 1° 3° 5° DocID2572 Rev 37 35/46 Package information LD1117 Figure 18. DPAK (TO-252) package outline I 36/46 DocID2572 Rev 37 LD1117 Package information Table 22. Footprint data Values mm. inch. A 6.70 0.264 B 6.70 0.64 C 1.8 0.070 D 3.0 0.118 E 1.60 0.063 F 2.30 0.091 G 2.30 0.091 Figure 19. DPAK footprint recommended data DocID2572 Rev 37 37/46 Packaging mechanical data 9 LD1117 Packaging mechanical data Figure 20. Drawing dimension tube for TO-220 Dual Gauge (mm.) Figure 21. Drawing dimension tube for TO-220 Single Gauge (mm.) 38/46 DocID2572 Rev 37 LD1117 Packaging mechanical data Table 23. SOT-223 tape and reel mechanical data Tape Reel mm mm Dim. Dim. Min. Typ. Max. Min. Max. A0 6.75 6.85 6.95 A B0 7.30 7.40 7.50 N K0 1.80 1.90 2.00 W1 12.4 F 5.40 5.50 5.60 W2 18.4 E 1.65 1.75 1.85 W3 W 11.7 12 12.3 P2 1.90 2 2.10 Base quantity pcs 1000 P0 3.90 4 4.10 Bulk quantity pcs 1000 P1 7.90 8 8.10 T 0.25 0.30 0.35 Dφ 1.50 1.55 1.60 D1φ 1.50 1.60 1.70 180 60 11.9 15.4 Figure 22. Tape for SOT-223 (dimensions are in mm) *Cumulative tolerance of 10 sprocket holes is ±0.20 mm DocID2572 Rev 37 39/46 Packaging mechanical data LD1117 Figure 23. Reel for SOT-223 (dimensions are in mm) 40/46 DocID2572 Rev 37 LD1117 Packaging mechanical data Table 24. SO-8 tape and reel mechanical data mm Dim. Min. Typ. A Max. 330 C 12.8 D 20.2 N 60 13.2 T 22.4 Ao 8.1 8.5 Bo 5.5 5.9 Ko 2.1 2.3 Po 3.9 4.1 P 7.9 8.1 Figure 24. SO-8 tape and reel dimensions DocID2572 Rev 37 41/46 Packaging mechanical data LD1117 Table 25. DPAK tape and reel mechanical data Tape Reel mm mm Dim. Dim. Min. Max. A0 6.8 7 A B0 10.4 10.6 B 1.5 12.1 C 12.8 1.6 D 20.2 G 16.4 50 B1 42/46 Min. Max. 330 13.2 D 1.5 D1 1.5 E 1.65 1.85 N F 7.4 7.6 T K0 2.55 2.75 P0 3.9 4.1 Base qty. 2500 P1 7.9 8.1 Bulk qty. 2500 P2 1.9 2.1 R 40 T 0.25 0.35 W 15.7 16.3 DocID2572 Rev 37 18.4 22.4 LD1117 Packaging mechanical data Figure 25. Tape for DPAK 10 pitches cumulative tolerance on tape +/- 0.2 mm T P0 Top cover tape P2 D E F B1 W K0 B0 For machine ref. only including draft and radii concentric around B0 A0 P1 D1 User direction of feed R Bending radius User direction of feed AM08852v1 Figure 26. Reel for DPAK T REEL DIMENSIONS 40mm min. Access hole At sl ot location B D C N A Full radius Tape slot in core for tape start 25 mm min. width G measured at hub AM08851v2 DocID2572 Rev 37 43/46 Order codes 10 LD1117 Order codes Table 26. Order codes Packages SOT-223 SO-8 DPAK (Tape and reel) TO-220 TO-220 (Dual Gauge) Output voltages LD1117S12TR LD1117DT12TR 1.2 V LD1117S12CTR LD1117DT12CTR 1.2 V LD1117S18TR LD1117DT18TR LD1117S18CTR LD1117DT18CTR 1.8 V LD1117S25TR LD1117DT25TR 2.5 V LD1117S25CTR LD1117DT25CTR 2.5 V LD1117S33TR LD1117S33CTR LD1117S50TR LD1117D33TR LD1117D33CTR LD1117DT33TR LD1117V18 LD1117V33 LD1117DT33CTR LD1117V33C LD1117DT50TR LD1117V50 1.8 V LD1117V33-DG 3.3 V LD1117V33C-DG 3.3 V 3.3 V LD1117V50-DG 5V 5V LD1117S50CTR LD1117DT50CTR LD1117V50C LD1117STR LD1117DTTR LD1117V 5V LD1117V-DG ADJ from 1.25 to 15 V ADJ from 1.25 to 15 V LD1117SC-R 44/46 LD1117DTC-R DocID2572 Rev 37 ADJ from 1.25 to 15 V LD1117 11 Revision history Revision history Table 27. Document revision history Date Revision Changes 22-Sep-2004 15 Add new part number #12C; typing error: note on table 2. 25-Oct-2004 16 Add Vref reference voltage on table 12. 18-Jul-2005 17 The DPAK mechanical data updated. 25-Nov-2005 18 The TO220FM package removed. 14-Dec-2005 19 The Top on table 2 updated. 06-Dec-2006 20 DPAK mechanical data updated and added footprint data. 05-Apr-2007 21 Order codes updated. 30-Nov-2007 22 Added Table 1. 16-Apr-2008 23 Modified: Table 24 on page 42. 08-Jul-2008 24 Added note 1. on page 7. 30-Mar-2009 25 Modified: VIN max value Table 4 on page 10 and Figure 9 on page 23 29-Jul-2009 26 Modified: Table 24 on page 42. 03-Feb-2010 27 Modified Table 9 on page 15. 22-Mar-2010 28 Added: Table 16 on page 22, Figure 13 on page 23, Figure 14 on page 24, Figure 17 and Figure 18 on page 33 15-Nov-2010 29 Modified: RthJC value for TO-220 Table 2 on page 7. 30-Nov-2011 30 Added: order code LD1117V33-DG Table 24 on page 42. 13-Feb-2012 31 Added: order codes LD1117V50-DG and LD1117V-DG Table 24 on page 42. 19-Oct-2012 32 Added: RthJA value for DPAK, SOT-223 and SO-8 Table 2 on page 7. 20-Nov-2013 33 Part number LD1117xx changed to LD1117. Updated the Description in cover page, Section 8: Package mechanical data and Table 24: Order codes. Cancelled Table 1: Device summary. Added Section 9: Packaging mechanical data. Minor text changes. 12-Jun-2019 34 Updated Table 19, Table 20, Figure 16, Figure 17 and Figure 18. 16-Oct-2019 35 Updated Figure 2: Pin connections (top view). 04-Dec-2019 36 Added Table 20: DPAK (TO-252) mechanical data (type E). Updated pin 3 DPAK package in Figure 2: Pin connections (top view). 11-Feb-2020 37 Updated Figure 14: Drawing dimension SOT-223. DocID2572 Rev 37 45/46 LD1117 IMPORTANT NOTICE – PLEASE READ CAREFULLY STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgement. Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of Purchasers’ products. No license, express or implied, to any intellectual property right is granted by ST herein. Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product. ST and the ST logo are trademarks of ST. For additional information about ST trademarks, please refer to www.st.com/trademarks. All other product or service names are the property of their respective owners. Information in this document supersedes and replaces information previously supplied in any prior versions of this document. © 2020 STMicroelectronics – All rights reserved 46/46 DocID2572 Rev 37