LD29080PT90R

LD29080 800 mA fixed and adjustable output very low drop voltage regulator Datasheet - production data Description PPAK The LD29080 is a medium current, high accuracy, low-dropout voltage regulators series. These regulators feature 400 mV dropout voltage and very low ground current. Designed for medium current loads, these devices also find applications in lower current, extremely low dropout-critical systems, where their tiny dropout voltage and ground current values are important attributes. Typical application are in power supply switching post regulation, series power supply for monitors, series power supply for VCRs and TVs, computer systems and battery powered systems. DPAK SOT223 Features • Very low dropout voltage (typ. 0.4 at 800 mA) • Guaranteed output current up to 800 mA • Fixed and adjustable output voltage (± 1 % at 25 °C) • Internal current and thermal limit • Logic controlled electronic shutdown Table 1. Device summary Order codes Output voltages DPAK (tape and reel) PPAK (tape and reel) LD29080DT15R LD29080PT15R 1.5 V LD29080DT18R LD29080PT18R 1.8 V LD29080DT25R LD29080PT25R 2.5 V LD29080DT33R LD29080PT33R LD29080DT50R LD29080PT50R 5.0 V LD29080DT90R LD29080PT90R 9.0 V LD29080PTR ADJ February 2020 This is information on a product in full production. DocID10918 Rev 9 SOT223 LD29080S33R 3.3 V 1/26 www.st.com 26 Contents LD29080 Contents 1 Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 Pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3 Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 4 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 5 Typical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 6 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 7 Packaging mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 8 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 2/26 DocID10918 Rev 9 LD29080 1 Diagram Diagram Figure 1. Schematic diagram for adjustable version Figure 2. Schematic diagram for fixed version * Only for version with inhibit function. DocID10918 Rev 9 3/26 Pin configuration 2 LD29080 Pin configuration Figure 3. Pin connections (top view) 5 3 4 3 GND GND 2 GND 2 1 1 CS17230 1 2 3 CS17240 AM09358v1 PPAK DPAK SOT223 Table 2. Pin description Symbol PPAK DPAK SOT223 VI 2 1 1 GND 3 2 2 4 3 3 VO ADJ/N.C. (1) INHIBIT (2) 5 1 1. Not connected for fixed version. 2. Not internally pulled up; in order to assure the operating condition (device in ON mode), it must be connected to a positive voltage higher than 2 V. Figure 4. Application circuit VO = VREF (1 + R1/R2) * Only for version with inhibit function. 4/26 DocID10918 Rev 9 LD29080 3 Maximum ratings Maximum ratings Table 3. Absolute maximum ratings Symbol VI VINH 1. Parameter DC input voltage Inhibit input voltage Value Unit 30 (1) V 14 V IO Output current Internally limited mA PD Power dissipation Internally limited mW TSTG Storage temperature range - 55 to 150 °C TOP Operating temperature range - 40 to 125 °C Above 14 V the device is automatically in shut-down. Note: Absolute maximum ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is not implied. Table 4. Thermal data Symbol Parameter RthJC Thermal resistance junction-case RthJA Thermal resistance junction-ambient DPAK PPAK SOT223 Unit 8 8 25 °C/W 100 100 110 °C/W DocID10918 Rev 9 5/26 Electrical characteristics 4 LD29080 Electrical characteristics IO = 10 mA, (Note 4) TJ = 25 °C, VI = 3.5 V, VINH = 2V, CI = 330 nF, CO = 10 µF, unless otherwise specified. Table 5. Electrical characteristics of LD29080#15 Symbol Parameter Test conditions Min. Typ. Unit 13 V VI Operating input voltage IO = 10 mA to 800 mA VO Output voltage IO = 10 mA to 800 mA, VI = 3 to 7 V TJ = -40 to 125 °C ∆VO Load regulation IO = 10 mA to 800 mA 0.2 1.0 % ∆VO Line regulation VI = 3 to 13 V 0.06 0.5 % SVR Supply voltage rejection f = 120 Hz, VI = 3.8 ± 1 V, IO = 400 mA (Note 1) Iq Quiescent current 2.5 Max. 1.485 1.5 1.463 65 1.537 75 2 5 IO = 400 mA, TJ = -40 to 125 °C 8 20 IO = 800 mA, TJ = -40 to 125 °C 14 35 VI = 13 V, VINH = GND, TJ = -40 to 125 °C 130 180 1.2 Short circuit current RL = 0 VIL Control input logic low OFF MODE, TJ = -40 to 125 °C VIH Control input logic high ON MODE, TJ = -40 to 125 °C IINH Control input current VINH = 13V, TJ = -40 to 125 °C 5 eN Output noise voltage BP = 10 Hz to 100 kHz, IO = 100 mA (Note 1) 60 6/26 V dB IO = 10 mA, TJ = -40 to 125 °C Isc Note: 1.515 mA µA A 0.8 2 V V 10 µA µVRMS 1 Guaranteed by design. 2 Dropout voltage is defined as the input-to-output differential when the output voltage drops to 99% of its nominal value with VO + 1 V applied to VI. 3 Reference voltage is measured between output and GND pins, with ADJ PIN tied to VO. 4 In order to avoid any output voltage rise within the whole operating temperature range, due to output leakage current, a minimum load current of 2 mA is required. DocID10918 Rev 9 LD29080 Electrical characteristics IO = 10 mA, (Note 4) TJ = 25 °C, VI = 3.5 V, VINH = 2 V, CI = 330 nF, CO = 10 µF, unless otherwise specified. Table 6. Electrical characteristics of LD29080#18 Symbol Parameter Test conditions Min. Typ. Unit 13 V VI Operating input voltage IO = 10 mA to 800 mA VO Output voltage IO = 10 mA to 800 mA, VI = 3 to 7.3 V TJ = -40 to 125 °C ∆VO Load regulation IO = 10 mA to 800 mA 0.2 1.0 % ∆VO Line regulation VI = 3 to 13 V 0.06 0.5 % SVR Supply voltage rejection f = 120 Hz, VI = 3.8 ± 1 V, IO = 400 mA (Note 1) VDROP Iq Dropout voltage Quiescent current 2.5 Max. 1.782 1.8 1.755 62 1.845 72 0.1 IO = 400 mA, TJ = -40 to 125 °C (Note 2) 0.2 IO = 800 mA, TJ = -40 to 125 °C (Note 2) 0.4 0.7 IO = 10 mA, TJ = -40 to 125 °C 2 5 IO = 400 mA, TJ = -40 to 125 °C 8 20 IO = 800 mA, TJ = -40 to 125 °C 14 35 VI = 13 V, VINH = GND, TJ = -40 to 125 °C 130 180 1.2 Short circuit current RL = 0 VIL Control input logic low OFF MODE, TJ = -40 to 125 °C VIH Control input logic high ON MODE, TJ = -40 to 125 °C IINH Control input current VINH = 13 V, TJ = -40 to 125 °C 5 eN Output noise voltage BP = 10 Hz to 100 kHz, IO = 100 mA (Note 1) 72 V dB IO = 150 mA, TJ = -40 to 125 °C (Note 2) Isc Note: 1.818 V mA µA A 0.8 2 V V 10 µA µVRMS 1 Guaranteed by design. 2 Dropout voltage is defined as the input-to-output differential when the output voltage drops to 99% of its nominal value with VO + 1 V applied to VI. 3 Reference voltage is measured between output and GND pins, with ADJ PIN tied to VO. 4 In order to avoid any output voltage rise within the whole operating temperature range, due to output leakage current, a minimum load current of 2 mA is required. DocID10918 Rev 9 7/26 Electrical characteristics LD29080 IO = 10 mA, (Note 4) TJ = 25 °C, VI = 4.5 V, VINH = 2 V, CI = 330 nF, CO = 10 µF, unless otherwise specified. Table 7. Electrical characteristics of LD29080#25 Symbol Parameter Test conditions Min. Typ. Max. Unit 13 V VI Operating input voltage IO = 10 mA to 800 mA VO Output voltage IO = 10 mA to 800 mA, VI = 3.5 to 8 V TJ = -40 to 125 °C ∆VO Load regulation IO = 10 mA to 800 mA 0.2 1.0 % ∆VO Line regulation VI = 3.5 to 13 V 0.06 0.5 % SVR Supply voltage rejection f = 120 Hz, VI = 4.5 ± 1 V, IO = 400 mA (Note 1) VDROP Iq Dropout voltage Quiescent current 2.438 55 2.525 2.562 70 IO = 400 mA, TJ = -40 to 125 °C (Note 2) 0.2 IO = 800 mA, TJ = -40 to 125 °C (Note 2) 0.4 0.7 IO = 10 mA, TJ = -40 to 125 °C 2 5 IO = 400 mA, TJ = -40 to 125 °C 8 20 IO = 800 mA, TJ = -40 to 125 °C 14 35 VI = 13 V, VINH = GND, TJ = -40 to 125 °C 130 180 1.2 RL = 0 VIL Control input logic low OFF MODE, TJ = -40 to 125 °C VIH Control input logic high ON MODE, TJ = -40 to 125 °C IINH Control input current VINH = 13 V, TJ = -40 to 125 °C eN Output noise voltage BP = 10 Hz to 100 kHz, IO = 100 mA (Note 1) V dB 0.1 Short circuit current 8/26 2.5 IO = 150 mA, TJ = -40 to 125 °C (Note 2) Isc Note: 2.475 V mA µA A 0.8 2 V V 5 100 10 µA µVRMS 1 Guaranteed by design. 2 Dropout voltage is defined as the input-to-output differential when the output voltage drops to 99% of its nominal value with VO + 1 V applied to VI. 3 Reference voltage is measured between output and GND pins, with ADJ PIN tied to VO. 4 In order to avoid any output voltage rise within the whole operating temperature range, due to output leakage current, a minimum load current of 2 mA is required. DocID10918 Rev 9 LD29080 Electrical characteristics IO = 10 mA, (Note 4) TJ = 25 °C, VI = 5.3 V, VINH = 2 V, CI = 330 nF, CO = 10 µF, unless otherwise specified. Table 8. Electrical characteristics of LD29080#33 Symbol Parameter Test conditions Min. Typ. Max. Unit 13 V VI Operating input voltage IO = 10mA to 800mA VO Output voltage IO = 10 mA to 800 mA, VI = 4.3 to 8.8 V TJ = -40 to 125 °C ∆VO Load regulation IO = 10 mA to 800 mA 0.2 1.0 % ∆VO Line regulation VI = 4.3 to 13 V 0.06 0.5 % SVR Supply voltage rejection f = 120 Hz, VI = 5.3 ± 1 V, IO = 400 mA (Note 1) VDROP Iq Dropout voltage Quiescent current 3.3 3.218 52 3.333 3.382 67 0.1 IO = 400 mA, TJ = -40 to 125 °C (Note 2) 0.2 IO = 800 mA, TJ = -40 to 125 °C (Note 2) 0.4 0.7 IO = 10 mA, TJ = -40 to 125 °C 2 5 IO = 400 mA, TJ = -40 to 125 °C 8 20 IO = 800 mA, TJ = -40 to 125 °C 14 35 VI = 13 V, VINH = GND, TJ = -40 to 125 °C 130 180 1.2 Short circuit current RL = 0 VIL Control input logic low OFF MODE, TJ = -40 to 125 °C VIH Control input logic high ON MODE, TJ = -40 to 125 °C IINH Control input current VINH = 13 V, TJ = -40 to 125 °C eN Output noise voltage BP = 10 Hz to 100 kHz, IO = 100 mA (Note 1) V dB IO = 150 mA, TJ = -40 to 125 °C (Note 2) Isc Note: 3.267 V mA µA A 0.8 2 V V 5 132 10 µA µVRMS 1 Guaranteed by design. 2 Dropout voltage is defined as the input-to-output differential when the output voltage drops to 99% of its nominal value with VO + 1 V applied to VI. 3 Reference voltage is measured between output and GND pins, with ADJ PIN tied to VO. 4 In order to avoid any output voltage rise within the whole operating temperature range, due to output leakage current, a minimum load current of 2 mA is required. DocID10918 Rev 9 9/26 Electrical characteristics LD29080 IO = 10 mA, (Note 4) TJ = 25 °C, VI = 7 V, VINH = 2 V, CI = 330 nF, CO = 10 µF, unless otherwise specified. Table 9. Electrical characteristics of LD29080#50 Symbol Parameter Test conditions Min. Typ. Max. Unit 13 V VI Operating input voltage IO = 10 mA to 800 mA VO Output voltage IO = 10 mA to 800 mA, VI = 6 to 10.5 V TJ = -40 to 125 °C ∆VO Load regulation IO = 10 mA to 800 mA 0.2 1.0 % ∆VO Line regulation VI = 6 to 13 V 0.06 0.5 % SVR Supply voltage rejection f = 120 Hz, VI = 7 ± 1 V, IO = 400 mA (Note 1) VDROP Iq Dropout voltage Quiescent current 4.875 49 5.05 5.125 64 IO = 400 mA, TJ = -40 to 125 °C (Note 2) 0.2 IO = 800 mA, TJ = -40 to 125 °C (Note 2) 0.4 0.7 IO = 10 mA, TJ = -40 to 125 °C 2 5 IO = 400 mA, TJ = -40 to 125 °C 8 20 IO = 800 mA, TJ = -40 to 125 °C 14 35 VI = 13 V, VINH = GND, TJ = -40 to 125 °C 130 180 1.2 RL = 0 VIL Control input logic low OFF MODE, TJ = -40 to 125 °C VIH Control input logic high ON MODE, TJ = -40 to 125 °C IINH Control input current VINH = 13 V, TJ = -40 to 125 °C eN Output noise voltage BP = 10 Hz to 100 kHz, IO = 100 mA (Note 1) V dB 0.1 Short circuit current 10/26 5 IO = 150 mA, TJ = -40 to 125 °C (Note 2) Isc Note: 4.95 V mA µA A 0.8 2 V V 5 180 10 µA µVRMS 1 Guaranteed by design. 2 Dropout voltage is defined as the input-to-output differential when the output voltage drops to 99% of its nominal value with VO + 1 V applied to VI. 3 Reference voltage is measured between output and GND pins, with ADJ PIN tied to VO. 4 In order to avoid any output voltage rise within the whole operating temperature range, due to output leakage current, a minimum load current of 2 mA is required. DocID10918 Rev 9 LD29080 Electrical characteristics IO = 10 mA, (Note 4) TJ = 25 °C, VI = 10 V, VINH = 2 V, CI = 330 nF, CO = 10 µF, unless otherwise specified) Table 10. Electrical characteristics of LD29080#80 Symbol Parameter Test conditions Min. Typ. Max. Unit 13 V VI Operating input voltage IO = 10 mA to 800 mA VO Output voltage IO = 10 mA to 800 mA, VI = 9 to 13 V TJ = -40 to 125 °C ∆VO Load regulation IO = 10 mA to 800 mA 0.2 1.0 % ∆VO Line regulation VI = 9 to 13 V 0.06 0.5 % SVR Supply voltage rejection f = 120 Hz, VI = 10 ± 1 V, IO = 400 mA (Note 1) VDROP Iq Dropout voltage Quiescent current 8 7.80 45 8.08 8.20 59 0.1 IO = 400 mA, TJ = -40 to 125 °C (Note 2) 0.2 IO = 800 mA, TJ = -40 to 125 °C (Note 2) 0.4 0.7 IO = 10 mA, TJ = -40 to 125 °C 2 5 IO = 400 mA, TJ = -40 to 125 °C 8 20 IO = 800 mA, TJ = -40 to 125 °C 14 35 VI = 13 V, VINH = GND, TJ = -40 to 125 °C 130 180 1.2 Short circuit current RL = 0 VIL Control input logic low OFF MODE, TJ = -40 to 125 °C VIH Control input logic high ON MODE, TJ = -40 to 125 °C IINH Control input current VINH = 13 V, TJ = -40 to 125 °C eN Output noise voltage BP = 10 Hz to 100 kHz, IO = 100 mA (Note 1) V dB IO = 150 mA, TJ = -40 to 125 °C (Note 2) Isc Note: 7.92 V mA µA A 0.8 2 V V 5 320 10 µA µVRMS 1 Guaranteed by design. 2 Dropout voltage is defined as the input-to-output differential when the output voltage drops to 99% of its nominal value with VO + 1 V applied to VI. 3 Reference voltage is measured between output and GND pins, with ADJ PIN tied to VO. 4 In order to avoid any output voltage rise within the whole operating temperature range, due to output leakage current, a minimum load current of 2 mA is required. DocID10918 Rev 9 11/26 Electrical characteristics LD29080 IO = 10 mA, (Note 4) TJ = 25 °C, VI = 11 V, VINH = 2 V, CI = 330 nF, CO = 10 µF, unless otherwise specified. Table 11. Electrical characteristics of LD29080#90 Symbol Parameter Test conditions Min. Typ. Max. Unit 13 V VI Operating input voltage IO = 10 mA to 800 mA VO Output voltage IO = 10 mA to 800 mA, VI = 9 to 13 V TJ = -40 to 125 °C ∆VO Load regulation IO = 10 mA to 800 mA 0.2 1.0 % ∆VO Line regulation VI = 10 to 13 V 0.06 0.5 % SVR Supply voltage rejection f = 120 Hz, VI = 11 ± 1 V, IO = 400 mA (Note 1) VDROP Iq Dropout voltage Quiescent current 8.775 43 9.09 9.225 57 IO = 400 mA, TJ = -40 to 125 °C (Note 2) 0.2 IO = 800 mA, TJ = -40 to 125 °C (Note 2) 0.4 0.7 IO = 10 mA, TJ = -40 to 125 °C 2 5 IO = 400 mA, TJ = -40 to 125 °C 8 20 IO = 800 mA, TJ = -40 to 125 °C 14 35 VI = 13 V, VINH = GND, TJ = -40 to 125 °C 130 180 1.2 RL = 0 VIL Control input logic low OFF MODE, TJ = -40 to 125 °C VIH Control input logic high ON MODE, TJ = -40 to 125 °C IINH Control input current VINH = 13 V, TJ = -40 to 125 °C eN Output noise voltage BP = 10 Hz to 100 kHz, IO = 100 mA (Note 1) V dB 0.1 Short circuit current 12/26 9 IO = 150 mA, TJ = -40 to 125 °C (Note 2) Isc Note: 8.91 V mA µA A 0.8 2 V V 5 330 10 µA µVRMS 1 Guaranteed by design. 2 Dropout voltage is defined as the input-to-output differential when the output voltage drops to 99% of its nominal value with VO + 1 V applied to VI. 3 Reference voltage is measured between output and GND pins, with ADJ PIN tied to VO. 4 In order to avoid any output voltage rise within the whole operating temperature range, due to output leakage current, a minimum load current of 2 mA is required. DocID10918 Rev 9 LD29080 Electrical characteristics IO = 10 mA, (Note 4) TJ = 25 °C, VI = 10 V, VINH = 2 V, CI = 330 nF, CO = 10 µF, unless otherwise specified. Table 12. Electrical characteristics of LD29080#ADJ Symbol Parameter Test conditions Min. Typ. Unit 13 V Operating input voltage IO = 10 mA to 800 mA ∆VO Load regulation IO = 10 mA to 800 mA 0.2 1.0 % ∆VO Line regulation VI = 2.5 to 13 V, IO = 10 mA 0.06 0.5 % VREF Reference voltage IO = 10 mA to 800 mA, VI = 2.5 to 6.73 V 1.2177 TJ = -40 to 125 °C (Note 3) 1.1993 1.23 1.2423 SVR Supply voltage rejection f = 120 Hz, VI = 3.23 ± 1 V, IO = 400 mA (Note 1) VI Iq IADJ Quiescent current 2.5 Max. 45 1.2607 75 dB IO = 10 mA, TJ = -40 to 125 °C 2 5 IO = 400 mA, TJ = -40 to 125 °C 8 20 IO = 800 mA, TJ = -40 to 125 °C 14 35 VI = 13 V, VINH = GND, TJ = -40 to 125 °C 130 180 µA 1 µA Adjust pin current TJ = -40 to 125 °C Isc Short circuit current RL = 0 VIL Control input logic low OFF MODE, TJ = -40 to 125 °C VIH Control input logic high ON MODE, TJ = -40 to 125 °C IINH Control input current VINH = 13 V, TJ = -40 to 125 °C 5 eN Output noise voltage BP = 10 Hz to 100 kHz, IO = 100 mA (Note 1) 50 Note: V 1.2 mA A 0.8 2 V V 10 µA µVRMS 1 Guaranteed by design. 2 Dropout voltage is defined as the input-to-output differential when the output voltage drops to 99% of its nominal value with VO + 1 V applied to VI. 3 Reference voltage is measured between output and GND pins, with ADJ PIN tied to VO. 4 In order to avoid any output voltage rise within the whole operating temperature range, due to output leakage current, a minimum load current of 2 mA is required. DocID10918 Rev 9 13/26 Typical characteristics 5 LD29080 Typical characteristics Figure 5. Output voltage vs. temperature Figure 6. Reference voltage vs. temperature Figure 7. Dropout voltage vs. temperature Figure 8. Dropout voltage vs. output current Figure 9. Quiescent current vs. output current Figure 10. Quiescent current vs. temperature (Io = 10 mA) 14/26 DocID10918 Rev 9 LD29080 Typical characteristics Figure 11. Quiescent current vs. supply voltage Figure 12. Quiescent current vs. temperature (Io = 800 mA) Figure 13. Short circuit current vs. temperature Figure 14. Adjust pin current vs. temperature Figure 15. Supply voltage rejection vs. temperature Figure 16. Output voltage vs. input voltage DocID10918 Rev 9 15/26 Typical characteristics LD29080 Figure 17. Stability vs. CO Figure 18. Line transient VI = 3.5 to 13 V, IO = 10 mA, VO = 1.5 V Figure 19. Load transient VI = 3.5 V, IO = 10 mA to 0.8 A, VO = 1.5 V 16/26 DocID10918 Rev 9 LD29080 6 Package mechanical data Package mechanical data In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK packages, depending on their level of environmental compliance. ECOPACK specifications, grade definitions and product status are available at: www.st.com. ECOPACK is an ST trademark. Table 13. PPAK mechanical data mm Dim. Min. Typ. Max. A 2.2 2.4 A1 0.9 1.1 A2 0.03 0.23 B 0.4 0.6 B2 5.2 5.4 C 0.45 0.6 C2 0.48 0.6 D 6 6.2 D1 E 5.1 6.4 E1 6.6 4.7 e 1.27 G 4.9 5.25 G1 2.38 2.7 H 9.35 10.1 L2 0.8 L4 0.6 L5 1 L6 1 2.8 R V2 1 0.20 0° DocID10918 Rev 9 8° 17/26 Package mechanical data LD29080 Figure 20. PPAK drawing 0078180_F 18/26 DocID10918 Rev 9 LD29080 Package mechanical data Table 14. DPAK mechanical data mm Dim. Min. Typ. Max. A 2.20 2.40 A1 0.90 1.10 A2 0.03 0.23 b 0.64 0.90 b4 5.20 5.40 c 0.45 0.60 c2 0.48 0.60 D 6.00 6.20 D1 E 5.10 6.40 6.60 E1 4.70 e 2.28 e1 4.40 4.60 H 9.35 10.10 L 1.00 1.50 (L1) 2.80 L2 0.80 L4 0.60 1.00 R V2 0.20 0° 8° DocID10918 Rev 9 19/26 Package mechanical data LD29080 Figure 21. DPAK drawing 0068772_K 20/26 DocID10918 Rev 9 LD29080 Package mechanical data Figure 22. DPAK footprint (a) Footprint_REV_K a. All dimensions are in millimeters DocID10918 Rev 9 21/26 Package mechanical data LD29080 Table 15. SOT-223 mechanical data mm Dim. Min. Typ. A 1.80 A1 0.02 0.1 B 0.60 0.70 0.85 B1 2.90 3.00 3.15 c 0.24 0.26 0.35 D 6.30 6.50 6.70 e 2.30 e1 4.60 E 3.30 3.50 3.70 H 6.70 7.00 7.30 V 10° Figure 23. SOT-223 mechanical data drawing 22/26 Max. DocID10918 Rev 9 LD29080 7 Packaging mechanical data Packaging mechanical data Table 16. PPAK and DPAK tape and reel mechanical data Tape Reel mm mm Dim. Dim. Min. Max. A0 6.8 7 A B0 10.4 10.6 B 1.5 12.1 C 12.8 1.6 D 20.2 G 16.4 50 B1 Min. Max. 330 13.2 D 1.5 D1 1.5 E 1.65 1.85 N F 7.4 7.6 T K0 2.55 2.75 P0 3.9 4.1 Base qty. 2500 P1 7.9 8.1 Bulk qty. 2500 P2 1.9 2.1 R 40 T 0.25 0.35 W 15.7 16.3 DocID10918 Rev 9 18.4 22.4 23/26 Packaging mechanical data LD29080 Figure 24. Tape for PPAK and DPAK 10 pitches cumulative tolerance on tape +/- 0.2 mm T P0 Top cover tape P2 D E F B1 W K0 B0 For machine ref. only including draft and radii concentric around B0 A0 P1 D1 User direction of feed R Bending radius User direction of feed AM08852v1 Figure 25. Reel for PPAK and DPAK T REEL DIMENSIONS 40mm min. Access hole At slot location B D C N A Full radius Tape slot in core for tape start 25 mm min. width G measured at hub AM08851v2 24/26 DocID10918 Rev 9 LD29080 8 Revision history Revision history Table 17. Document revision history Date Revision Changes 15-Oct-2004 1 First release. 20-Oct-2005 2 Order codes updated. 14-May-2007 3 Order codes updated. 26-Jan-2009 4 Modified: eN value in Table 9 on page 10. 22-Feb-2011 5 Added: new order code Table 1 on page 1 and mechanical data. 12-Jan-2012 6 Modified: RthJA and RthJC value for SOT223 Table 4 on page 5. 08-May-2012 7 Modified: pin connections for PPAK, DPAK and SOT223 Figure 3 on page 4. 22-Nov-2013 8 Part number LD29080xx changed to LD29080. Updated the Description in cover page, Table 1: Device summary. Updated Section 5: Typical characteristics and Section 6: Package mechanical data. Added Section 7: Packaging mechanical data. Minor text changes. 13-Feb-2020 9 Updated Figure 23: SOT-223 mechanical data drawing. DocID10918 Rev 9 25/26 LD29080 IMPORTANT NOTICE – PLEASE READ CAREFULLY STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgement. Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of Purchasers’ products. No license, express or implied, to any intellectual property right is granted by ST herein. Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product. ST and the ST logo are trademarks of ST. For additional information about ST trademarks, please refer to www.st.com/trademarks. All other product or service names are the property of their respective owners. Information in this document supersedes and replaces information previously supplied in any prior versions of this document. © 2020 STMicroelectronics – All rights reserved 26/26 DocID10918 Rev 9