LED7706
6-rows 30 mA LEDs driver with boost regulator
for LCD panels backlight
Features
■
■
Boost section
– 4.5 V to 36 V input voltage range
– Internal power MOSFET
– Internal +5 V LDO for device supply
– Up to 36 V output voltage
– Constant frequency peak current-mode
control
– 250 kHz to 1 MHz adjustable switching
frequency
– External synchronization for multi-device
application
– Pulse-skip power saving mode at light load
– Programmable soft-start
– Programmable OVP protection
– Stable with ceramic output capacitors
– Thermal shutdown
Backlight driver section
– Six rows with 30 mA maximum current
capability (adjustable)
– Rows disable option
– Less than 500 ns minimum dimming ontime (1 % minimum dimming duty-cycle at
20 kHz)
– ±2 % current matching between rows
– LED failure (open and short-circuit)
detection
VFQFPN-24 4x4
Description
The LED7706 consists of a high efficiency
monolithic boost converter and six controlled
current generators (rows) specifically designed to
supply LEDs arrays used in the backlighting of
LCD panels. The device can manage an output
voltage up to 36 V (i.e. 10 white LEDs per row).
The generators can be externally programmed to
sink up to 30 mA and can be dimmed via a PWM
signal (1 % dimming duty-cycle at 20 kHz can be
managed). The device allows to detect and
manage the open and shorted LED faults and to
let unused rows floating. Basic protections (output
over-voltage, internal MOSFET over-current and
thermal shutdown) are provided.
Applications
■
LCD monitors and TV panels
■
PDAs panel backlight
■
GPS panel backlight
Table 1.
Device summary
Order codes
Package
LED7706
Packaging
Tube
VFQFPN-24 4x4 (exposed pad)
LED7706TR
April 2009
Tape and reel
Rev 2
1/46
www.st.com
46
Contents
LED7706
Contents
1
Typical application circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2
Pin settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3
2.1
Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.2
Pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Electrical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.1
Maximum rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.2
Thermal data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
4
Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
5
Operation description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
5.1
5.2
5.3
2/46
Boost section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5.1.1
Functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5.1.2
Enable function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
5.1.3
Soft-start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5.1.4
Overvoltage protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
5.1.5
Switching frequency selection and synchronization . . . . . . . . . . . . . . . 15
5.1.6
Slope compensation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5.1.7
Boost current limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
5.1.8
Thermal protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Backlight driver section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
5.2.1
Current generators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
5.2.2
PWM dimming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Fault management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
5.3.1
FAULT pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
5.3.2
MODE pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
5.3.3
Open LED fault . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
5.3.4
Shorted LED fault . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
LED7706
6
Contents
Application information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
6.1
System stability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
6.1.1
Loop compensation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
6.2
Thermal considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
6.3
Component selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
6.4
6.5
6.3.1
Inductor selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
6.3.2
Capacitors selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
6.3.3
Flywheel diode selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Design example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
6.4.1
Switching frequency setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
6.4.2
Row current setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
6.4.3
Inductor choice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
6.4.4
Output capacitor choice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
6.4.5
Input capacitor choice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
6.4.6
Over-voltage protection divider setting . . . . . . . . . . . . . . . . . . . . . . . . . 33
6.4.7
Compensation network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
6.4.8
Boost current limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
6.4.9
Power dissipation estimate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Layout consideration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
7
Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
8
Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
9
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
3/46
Typical application circuit
1
LED7706
Typical application circuit
Figure 1.
Application circuit
L
VIN
VOUT
Slope Compensation
OVP selection
MLCC
+5V
SWF
OVSEL
LX
LDO5
SLOPE
VIN
AVCC
Switching Frequency selection
ROW1
Internal MOS OCP
BILIM
ROW2
RILIM
ROW3
Rows current selection
LED7706
SS
ROW4
PGND
MODE
SYNC
ROW6
EN
SGND
FAULT
ROW5
DIM
COMP
Up to 10 WLEDs per row
Dimming
Fault
Enable
Faults Management Selection
Sync Output
AM00594v1
4/46
LED7706
Pin settings
2
Pin settings
2.1
Connections
COMP
1
LX
DIM
EN
FAULT
SYNC
SS
Pin connection (through top view)
19
18
24
RILIM
BILIM
ROW6
LED7706
FSW
ROW5
MODE
ROW4
13
12
6
ROW3
ROW2
ROW1
SGND
SLOPE
7
VIN
AVCC
OVSEL
PGND
LDO5
Figure 2.
AM00595v1
5/46
Pin settings
2.2
LED7706
Pin description
Table 2.
6/46
Pin functions
N°
Pin
Function
1
COMP
Error amplifier output. A simple RC series between this pin and ground is
needed to compensate the loop of the boost regulator.
2
RILIM
Output generators current limit setting. The output current of the rows can be
programmed connecting a resistor to SGND.
3
BILIM
Boost converter current limit setting. The internal MOSFET current limit can
be programmed connecting a resistor to SGND.
4
FSW
Switching frequency selection and external sync input. A resistor to SGND is
used to set the desired switching frequency. The pin can also be used as
external synchronization input. See Section 5.1.5 on page 15 for details.
5
MODE
Current generators fault management selector. It allows to detect and manage
LEDs failures. See Section 5.3.2 on page 21 for details.
6
AVCC
+ 5 V analog supply. Connect to LDO5 through a simple RC filter.
7
LDO5
+ 5 V LDO output and power section supply. Bypass to SGND with a
1 μF ceramic capacitor.
8
VIN
9
SLOPE
Slope compensation setting. A resistor between the output of the boost
converter and this pin is needed to avoid sub-harmonic instability.
Refer to Section 6.1 on page 24 for details.
10
SGND
Signal ground. Supply return for the analog circuitry and the current
generators.
11
ROW1
Row driver output #1.
12
ROW2
Row driver output #2.
13
ROW3
Row driver output #3.
14
ROW4
Row driver output #4.
15
ROW5
Row driver output #5.
16
ROW6
Row driver output #6.
17
PGND
Power ground. Source of the internal Power MOSFET.
18
OVSEL
Over-voltage selection. Used to set the desired OV threshold by an external
divider. See Section 5.1.4 on page 14 for details.
19
LX
20
DIM
Dimming input. Used to externally set the brightness by using a PWM signal.
21
EN
Enable input. When low, the device is turned off. If tied high or left open, the
device is turned on and a soft-start sequence takes place.
22
FAULT
Fault signal output. Open drain output. The pin goes low when a fault condition
is detected (see Section 5.3.1 on page 21 for details).
23
SYNC
Synchronization output. Used as external synchronization output.
24
SS
Input voltage. Connect to the main supply rail.
Switching node. Drain of the internal Power MOSFET.
Soft-start. Connect a capacitor to SGND to set the desired soft-start duration.
LED7706
Electrical data
3
Electrical data
3.1
Maximum rating
Table 3.
Absolute maximum ratings (1)
Symbol
Parameter
Value
VAVCC
AVCC to SGND
-0.3 to 6
VLDO5
LDO5 to SGND
-0.3 to 6
PGND to SGND
-0.3 to 0.3
VIN
VIN to PGND
-0.3 to 40
VLX
LX to SGND
-0.3 to 40
LX to PGND
-0.3 to 40
RILIM, BILIM, SYNC, OVSEL, SS to SGND
V
-0.3 to VAVCC + 0.3
EN, DIM, SW, MODE, FAULT to SGND
-0.3 to 6
ROWx to PGND/ SGND
-0.3 to 40
VIN - 0.3 to VIN + 6
SLOPE to VIN
SLOPE to SGND
-0.3 to 40
Internal switch maximum RMS current
(flowing through LX node)
PTOT
Unit
2.0
A
Power dissipation @ TA = 25 °C
2.3 (2)
W
Maximum withstanding voltage range test condition:
CDF-AEC-Q100-002- “human body model” acceptance
criteria: “normal performance”
±1000
V
1. Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the
device. Exposure to absolute maximum rated conditions for extended periods may affect device reliability.
2. Power dissipation referred to the device mounted on the demonstration board described in section 5.5
3.2
Thermal data
Table 4.
Symbol
Thermal data
Parameter
Value
Unit
42
°C/W
RthJA
Thermal resistance junction to ambient
TSTG
Storage temperature range
-50 to 150
°C
Junction operating temperature range
-40 to 150
°C
TJ
7/46
Electrical characteristics
4
LED7706
Electrical characteristics
VIN = 12 V; TJ = 25 °C and LDO5 connected to AVCC if not otherwise specified (a)
Table 5.
Electrical characteristics
Symbol
Parameter
Test condition
Min.
Typ.
Max.
Unit
36
V
Supply section
VIN
Input voltage range
4.5
VBST
Boost section output voltage
VLDO5
LDO output and IC supply
voltage
EN High
ILDO5 = 0 mA
Operating quiescent current
RRILIM = 51 kΩ, RBILIM = 220 kΩ,
RSLOPE = 680 kΩ
DIM tied to SGND.
1
Operating current in shutdown
EN low
20
30
3.8
4.0
VAVCC
IIN,Q
IIN,SHDN
VUVLO,ON
LDO5 under voltage lock out
upper threshold
VUVLO,OFF
LDO5 under voltage lock out
lower threshold
36
4.4
5
5.5
V
mA
μA
V
3.3
3.6
LDO linear regulator
Line regulation
6 V ≤ VIN ≤ 36 V, ILDO5 = 30 mA
LDO dropout voltage
VIN = 4.3 V, ILDO5 = 10 mA
LDO maximum output current
VLDO5 > VUVLO,ON
30
25
VLDO5 < VUVLO,OFF
80
120
40
60
20
30
mV
mA
Boost section
tON,min
Minimum switching on-time
fSW
Default switching frequency
200
FSW connected to AVCC
570
Minimum FSW sync frequency
660
750
210
FSW sync input threshold
ns
kHz
240
FSW sync low level
FSW sync input hysteresis
350
mV
270
ns
40
%
20
FSW sync min. ON time
SYNC output Duty-Cycle
FSW connected to AVCC
(Internal oscillator selected)
SYNC output high level
ISYNC = 10 μA
SYNC output low level
ISYNC = -10 μA
34
VAVCC
-20V
mV
20
a. Specification referred to TJ from 0 °C to +85 °C. Specification over the 0 to +85 °C TJ range are assured by
design, characterization and statistical correlation.
8/46
LED7706
Table 5.
Electrical characteristics
Electrical characteristics (continued)
Symbol
Parameter
Test condition
Min.
Typ.
Max.
Unit
5·105
6·105
7·105
V
280
500
mΩ
1.234
1.280
Power switch
KB
RDSon
LX current coefficient
RBILIM = 600 kΩ
Internal MOSFET on-resistance
OC and OV protections
VTH,OVP
Over voltage protection
reference threshold (OVSEL)
1.190
VTH,FRD
Floating channel detection
threshold
1.100
ΔVOVP,FRD
V
Voltage gap between OVP and
FRD thresholds
1.145
1.190
90
mV
Soft-start and power management
EN, Turn-on threshold
1.6
EN, Turn-off threshold
0.8
DIM, high level threshold
1.3
V
DIM, low level threshold
0.8
EN, pull-up current
2.5
SS, charge current
SS, end-of-startup threshold
SS, reduced switching
frequency release threshold
4
5
6
2.0
2.4
2.8
μA
V
0.8
Current generators section
TDIM-
Minimum dimming on-time
500
ns
KR
Current generators gain
987
V
ΔKR(1)
Current generators gain
accuracy
ON,min
±2.0
VIFB
Feedback regulation voltage
Vrowx,
Shorted LED fault detection
threshold
MODE tied to SGND
3.4
MODE connected to AVCC
6.0
FAULT pin low-level voltage
IFAULT,SINK = 4 mA
200
FAULT
VFAULT,
LOW
400
%
mV
V
350
mV
Thermal shutdown
TSHDN
Thermal shutdown
turn-off temperature
150
Thermal shutdown hysteresis
30
°C
1. IROW = KR / RRILIM, ΔIROW/IROW ≈ ΔKR/KR+ ΔRRILIM/RRILIM
9/46
Operation description
5
LED7706
Operation description
The device can be divided into two sections: the boost section and the backlight driver
section. These sections are described in the next paragraphs. Figure 3 provides an
overview of the internal blocks of the device.
Figure 3.
Simplified block diagram
VIN
SLOPE
Current Sense
+5V
LDO
+ +
UVLO
Detector
UVLO
+
0.7V
gm
_
BILIM
Boost
Control
Logic
_
COMP
LX
ZCD
+
LDO5
Ramp
Generator
PGND
Boost_EN
Current Limit
_
OVP
SS
VROW6
Prot_EN
Current
Generator 6
CTRL6
÷2
VROW5
Current
Generator 5
CTRL5
Ext Sync
Detector
VROW4
OSC
Current
Generator 4
CTRL4
VROW3
FSW
Current
Generator 3
CTRL3
VROW2
Prot_EN
EN
MODE
Current
Generator 2
CTRL2
Boost_EN
AVCC
OVSEL
Min Voltage
Selector
Soft Start
SYNC
1.172V
+
ROW6
ROW5
ROW4
ROW3
ROW2
UVLO
CONTROL
LOGIC
CTRL6
CTRL5
CTRL4
CTRL3
CTRL2
MODE
CTRL1
LOGIC
VROW1
OVP
FAULT
VTH,FLT
4V
ROW1
I to V
+
_
DIM
I to V
Thermal
Shutdown
Current
Generator 1
1.2V
RILIM
10/46
SGND
AM00596v1
LED7706
Operation description
5.1
Boost section
5.1.1
Functional description
The LED7706 is a monolithic LEDs driver for the backlight of LCD panels and it consists of a
boost converter and six PWM-dimmable current generators.
The boost section is based on a constant switching frequency, peak current-mode
architecture. The boost output voltage is controlled such that the lowest row's voltage,
referred to SGND, is equal to an internal reference voltage (400 mV typ. see Figure 5). The
input voltage range is from 4.5 V up to 36 V. In addition, the LED7706 has an internal LDO
that supplies the internal circuitry of the device and is capable to deliver up to 40 mA. The
input of the LDO is the VIN pin.
The LDO5 pin is the LDO output and the supply for the power MOSFET driver at the same
time. The AVCC pin is the supply for the analog circuitry and should be connected to the
LDO output through a simple RC filter in order to improve the noise rejection.
Figure 4.
AVCC filtering
VIN
LDO5
LDO
Rfilt
4R7 AVCC
CLDO5
1uF
LED7706
CAVCC
100nF
SGND
AM00597v1
Two loops are involved in regulating the current sunk by the generators.
The main loop is related to the boost regulator and uses a constant frequency peak currentmode architecture to regulate the power rail that supplies the LEDs (Figure 5), while an
internal current loop regulates the same current (flowing through the LEDs) at each row
according to the set value (RILIM pin).
Figure 5.
Main loop and current loop diagram
VIN
ROWx
LX
Slope
SGND
PWM
COMP
E/A
Minimum voltage drop
selector
RILIM
0.4V
Error amplifier
AM00598v1
11/46
Operation description
LED7706
A dedicated circuit automatically selects the lowest voltage drop among all the rows and
provides this voltage to the main loop that, in turn, regulates the output voltage. In fact, once
the reference generator has been detected, the error amplifier compares its voltage drop to
the internal reference voltage and varies the COMP output. The voltage at the COMP pin
determines the inductor peak current at each switching cycle. The output voltage of the
boost regulator is thus determined by the total forward voltage of the LEDs strings (see
Figure 6):
Equation 1
NROWS mLEDS
VOUT = max (
i=1
Σ
VF,j ) + 400mV
j=1
where the first term represents the highest total forward voltage drop over N active rows and
the second is the voltage drop across the leading generator (400 mV typ.).
The device continues to monitor the voltage drop across all the rows and automatically
switches to the current generator having the lowest voltage drop.
Figure 6.
Calculation of the output voltage of the boost regulator
Row with the highest voltage
drop across LEDs
VIN
max
Σ VF
Boost
controller
VBOOST
ILED
Current
generators
section
400 mV
Leading
generator
AM00599v1
8 1
5.1.2
Enable function
The LED7706 is enabled by the EN pin. This pin is active high and, when forced to SGND,
the device is turned off. This pin is connected to a permanently active 2.5 μA current source;
when sudden device turn-on at power-up is required, this pin must be left floating or
connected to a delay capacitor. When turned off, the LED7706 quickly discharges the
soft-start capacitor and turns off the power MOSFET, the current generators and the LDO.
The power consumption is thus reduced to 20 μA only.
In applications where the dimming signal is used to turn on and off the device, the EN pin
can be connected to the DIM pin as shown in Figure 7.
12/46
LED7706
Operation description
Figure 7.
Enable pin driven by dimming signal
DIM
BAS69
EN
220kΩ
LED7706
100nF
SGND
AM00600v1
5.1.3
Soft-start
The soft-start function is required to perform a correct start-up of the system, controlling the
inrush current required to charge the output capacitor and to avoid output voltage overshoot.
The soft-start duration is set connecting an external capacitor between the SS pin and
ground. This capacitor is charged with a 5 μA (typ.) constant current, forcing the voltage on
the SS pin to ramp up. When this voltage increases from zero to nearly 1.2 V, the current
limit of the power MOSFET is proportionally released from zero to its final value. However,
because of the limited minimum on-time of the switching section, the inductor might saturate
due to current runaway. To solve this problem the switching frequency is reduced to one half
of the nominal value at the beginning of the soft-start phase. The nominal switching
frequency is restored after the SS pin voltage has crossed 0.8 V.
Figure 8.
Soft-start sequence waveforms in case of floating rows
OVP
Floating ROWs detection
95% of
OVP
Output voltage
SS pin voltage
AVCC
2.4V
1.2V
0.8V
Protections turn active
tss
100%
Nominal switching
frequency release
Current limit
EN pin voltage
t
AM00601v1
During the soft-start phase the floating rows detection is also performed. In presence of one
or more floating rows, the voltage across the involved current generator drops to zero. This
voltage becomes the inverting input of the error amplifier through the minimum voltage drop
13/46
Operation description
LED7706
selector (see Figure 5). As a consequence the error amplifier is unbalanced and the loop
reacts by increasing the output voltage. When it reaches the floating row detection (FRD)
threshold (95% of the OVP threshold), the floating rows are managed according to Table 6
(see Section 5.3 on page 21). After the SS voltage reaches a 2.4 V threshold, the start-up
finishes and all the protections turn active. The soft-start capacitor CSS can be calculated
according to equation 2.
Equation 2
C SS ≅
ISS ⋅ t SS
2 .4
Where ISS = 5 µA and tSS is the desired soft-start duration.
5.1.4
Overvoltage protection
An adjustable over-voltage protection is available. It can be set feeding the OVSEL pin with a
partition of the output voltage. The voltage of the central tap of the divider is thus compared
to a fixed 1.234 V threshold. When the voltage on the OVSEL pin exceeds the OV threshold,
the FAULT pin is tied low and the device is turned off; this condition is latched and the
LED7706 is restarted by toggling the EN pin or by performing a Power-On Reset (the POR
occurs when the LDO output falls below the lower UVLO threshold and subsequently
crosses the upper UVLO threshold during the rising phase of the input voltage). Normally,
the value of the high-side resistors of the divider must be chosen as high as possible (but
lower than 1 MΩ) to reduce the output capacitor discharge when the boost converter is off
(during the off phase of the dimming cycle). The R2/R1 ratio is calculated to trigger the OVP
circuitry as soon as the output voltage is 2 V higher than the maximum value for a given LED
string (see equation 3). Two additional filtering capacitors, C10 and C13, may be required to
improve noise rejection at the OVSEL pin, as shown in Figure 9. The typical value for C10 is
in the 100 pF-330 pF range, while the C13 value is given by equation 4.
Equation 3
R 2 = R1 ⋅
1.234 V
(VOUT,OVP + 2V − 1.234 V)
Equation 4
C13 = 2 ⋅ C10
14/46
R2
R1
LED7706
Operation description
Figure 9.
OVP threshold setting
VIN
VOUT
C13
LX
R1
COUT
OVSEL
LED7706
R2
C10
SGND
AM00602v1
5.1.5
Switching frequency selection and synchronization
The switching frequency of the boost converter can be set in the 250 kHz-1 MHz range by
connecting the FSW pin to ground through a resistor. Calculation of the setting resistor is
made using equation 5 and should not exceed the 100 kΩ-400 kΩ range.
Equation 5
RFSW =
FSW
2.5
In addition, when the FSW pin is tied to AVCC, the LED7706 uses a default 660 kHz fixed
switching frequency, allowing to save a resistor in minimum component-count applications.
Figure 10. Multiple device synchronization
SLAVE
MASTER
AVCC
Sync Out
FSW
SYNC
LED7706
RFSW
SGND
FSW
SYNC
SYNC
LED7706
SGND
AM00603v1
The FSW pin can also be used as synchronization input, allowing the LED7706 to operate
both as master or slave device. If a clock signal with a 210 kHz minimum frequency is
applied to this pin, the device locks synchronized. The signal provided to the FSW pin must
cross the 270 mV threshold in order to be recognized. The minimum pulse width which
allows the synchronizing pulses to be detected is 270 ns. An Internal time-out allows
synchronization as long as the external clock frequency is greater than 210 kHz.
15/46
Operation description
LED7706
Keeping the FSW pin voltage lower than 270 mV for more than 4.8 µs results in a stop of the
device switching activity. Normal operation is resumed as soon as FSW rises above the
mentioned threshold and the soft-start sequence is repeated.
The SYNC pin is a synchronization output and provides a 35 % (typ.) duty-cycle clock when
the LED7706 is used as master or a replica of the FSW pin when used as slave. It is used to
connect multiple devices in a daisy-chain configuration or to synchronize other switching
converters running in the system with the LED7706 (master operation). When an external
synchronization clock is applied to the FSW pin, the internal oscillator is over-driven: each
switching cycle begins at the rising edge of the clock, while the slope compensation
(Figure 11) ramp starts at the falling edge of the same signal. Thus, to prevent subharmonic instability (see Section 5.1.6), the external synchronization clock is required to
have a 40 % maximum duty-cycle when the boost converter is working in continuousconduction mode (CCM) in order to assure that the slope compensation is effective (starts
with duty-cycle lower than 40%)
Figure 11. External sync waveforms
270ns minimum
FSW pin voltage (ext. sync)
270mV threshold
Slave SYNC pin voltage
Slave LX pin voltage
AM00604v1
5.1.6
Slope compensation
The constant frequency, peak current-mode topology has the advantage of very easy loop
compensation with output ceramic caps (reduced cost and size of the application) and fast
transient response. In addition, the intrinsic peak-current measurement simplifies the
current limit protection, avoiding undesired saturation of the inductor.
On the other side, this topology has a drawback: there is an inherent open loop instability
when operating with a duty-ratio greater than 0.5. This phenomenon is known as “SubHarmonic Instability” and can be avoided by adding an external ramp to the one coming
from the sensed current. This compensating technique, based on the additional ramp, is
called “slope compensation”. In Figure 12, where the switching duty-cycle is higher than 0.5,
the small perturbation ΔIL dies away in subsequent cycles thanks to the slope compensation
and the system reverts to a stable situation.
16/46
LED7706
Operation description
The SLOPE pin allows to properly set the amount of slope compensation connecting a
simple resistor RSLOPE between the SLOPE pin and the output. The compensation ramp
starts at 35% (typ.) of each switching period and its slope is given by the following equation:
Equation 6
⎛V
− VIN − VBE
SE = K S ⎜⎜ OUT
R
SLOPE
⎝
⎞
⎟
⎟
⎠
Where KS = 5.8 ⋅1010 s-1, VBE = 2 V (typ.) and SE is the slope ramp in [A/s].
To avoid sub-harmonic instability, the compensating slope should be at least half the slope
of the inductor current during the off-phase when the duty-cycle is greater than 50%. The
value of RSLOPE can be calculated according to equation 7.
Equation 7
RSLOPE ≤
2 ⋅ K S ⋅ L ⋅ (VOUT − VIN − VBE )
(VOUT − VIN )
Figure 12. Effect of slope compensation on small inductor current perturbation
(D > 0.5)
Inductor current (CCM)
Programmed inductor peak current with
slope compensation (SE)
0.35·TSW
IBOOST, PEAK
ΔIL
Inductor current
perturbation
TSW
t
AM00606v1
17/46
Operation description
5.1.7
LED7706
Boost current limit
The design of the external components, especially the inductor and the flywheel diode, must
be optimized in terms of size relying on the programmable peak current limit. The LED7706
improves the reliability of the final application giving the way to limit the maximum current
flowing into the critical components. A simple resistor connected between the BILIM pin and
ground sets the desired value. The voltage at the BILIM pin is internally fixed to 1.23 V and
the current limit is proportional to the current flowing through the setting resistor, according
to the following equation:
Equation 8
IBOOST,PEAK =
KB
R BILIM
where
K B = 6 ⋅ 10 5 V
The maximum allowed current limit is 5 A, resulting in a minimum setting resistor
RBILIM > 120 kΩ. The maximum guaranteed RMS current in the power switch is 2 A.
In a boost converter the RMS current through the internal MOSFET depends on both the
input and output voltages, according to equations 9a (DCM) and 9b (CCM).
The current limitation works by clamping the COMP pin voltage proportionally to RBILIM.
Peak inductor current is limited to the above threshold decreased by the slope
compensation contribution.
Equation 9 a
IMOS,rms =
VIN ⋅ D D
FSW ⋅ L 3
Equation 9 b
IMOS,rms = IOUT
5.1.8
2
⎞
⎛ D
⎞
VOUT
1⎛
⎜
⎟ (D(1 − D))3 ⎟
⎜
+
⎟
⎟
⎜ (1 − D)2 12 ⎜ I
⎝ OUT ⋅ fSW ⋅ L ⎠
⎠
⎝
Thermal protection
In order to avoid damage due to high junction temperature, a thermal shutdown protection is
implemented. When the junction temperature rises above 150 °C (typ.), the device turns off
both the control logic and the boost converter and holds the FAULT pin low. The LDO is kept
alive and normal operation is automatically resumed after the junction temperature has
been reduced by 30 °C.
18/46
LED7706
Operation description
5.2
Backlight driver section
5.2.1
Current generators
The LED7706 is a LEDs driver with six channels (rows); each row is able to drive multiple
LEDs in series (max. 36 V) and to sink up to 30 mA maximum current, allowing to manage
different kinds of LEDs.
The LEDs current can be set by connecting an external resistor (RRILIM) between the RILIM
pin and ground. The voltage across the RILIM pin is internally set to 1.23 V and the rows
current is proportional to the RILIM current according to the following equation:
Equation 10
IROWx
=
KR
R RILIM
Where KR = 987 V.
The graph in Figure 13 better shows the relationship between IROW and RRILIM and helps to
choose the correct value of the resistor to set the desired row current.
Figure 13. Row current vs RRILIM
Row current vs RRILIM
35
Row current [mA]
30
25
20
15
10
5
0
0
50
100
150
200
250
RRILIM [kΩ]
AM00605v1
The maximum current mismatch between the rows is ± 2 % @ Irowx = 20 mA.
19/46
Operation description
5.2.2
LED7706
PWM dimming
The brightness control of the LEDs is performed by a pulse-width modulation of the rows
current. When a PWM signal is applied to the DIM pin, the current generators are turned on
and off mirroring the DIM pin behavior. Actually, the minimum dimming duty-cycle depends
on the dimming frequency.
The real limit to the PWM dimming is the minimum on-time that can be managed for the
current generators; this minimum on-time is approximately 500 ns.
Thus, the minimum dimming duty-cycle depends on the dimming frequency according to the
following formula:
Equation 11
DDIM,min = 500ns ⋅ fDIM
For example, at a dimming frequency of 20 kHz, 1% of dimming duty-cycle can be
managed.
During the off-phase of the PWM signal the boost converter is paused and the current
generators are turned off. The output voltage can be considered almost constant because of
the relatively slow discharge of the output capacitor. During the start-up sequence (see
Section 5.1.3 on page 13) the dimming duty-cycle is forced to 100% to detect floating rows
regardless of the applied dimming signal.
Figure 14. PWM dimming waveforms
20/46
LED7706
5.3
Operation description
Fault management
The main loop keeps the row having the lowest voltage drop regulated to about 400 mV.
This value slightly depends on the voltage across the remaining active rows. After the softstart sequence, all protections turn active and the voltage across the active current
generators is monitored to detect shorted LEDs.
5.3.1
FAULT pin
The FAULT pin is an open-collector output, (with 4 mA current capability) active low, which
gives information regarding faulty conditions eventually detected. This pin can be used
either to drive a status LED or to warn the host system.
The FAULT pin status is strictly related to the MODE pin setting (see Table 6 for details).
5.3.2
MODE pin
The MODE pin is a digital input and can be connected to AVCC or SGND in order to choose
the desired fault detection and management. The LED7706 can manage a faulty condition
in two different ways, according to the application needs. Table 6 summarizes how the
device detects and handles the internal protections related to the boost section (overcurrent, over-temperature and over-voltage) and to the current generators section (open and
shorted LEDs).
Table 6.
Faults management summary
FAULT
MODE to GND
MODE to VCC
Internal MOSFET over
current
FAULT pin HIGH
Power MOS turned OFF
Output over voltage
FAULT pin LOW
Device turned OFF, latched condition
Thermal shutdown
FAULT pin LOW. Device turned OFF.
Automatic restart after 30 C temperature drop.
LED short shorted led
FAULT pin LOW
Device turned OFF,
latched condition
(Vth = 3.4 V)
FAULT pin LOW
Faulty row(s) disconnected
Device keeps on working with the
remaining row(s)
(Vth = 6 V)
Open row(s)
FAULT pin LOW
Device turned OFF at first
occurrence, latched condition
FAULT pin HIGH Faulty row(s)
disconnected.
Device keeps on working with the
remaining row(s)
21/46
Operation description
5.3.3
LED7706
Open LED fault
In case a row is not connected or a LED fails open, the device has two different behaviors
according to the MODE pin status.
Connecting the MODE pin to SGND, as soon as an open row is detected the FAULT pin is
tied low and the device is turned off. The internal logic latches this status: to restore the
normal operation, the device must be restarted by toggling the EN pin or performing a
Power-On Reset (POR occurs when the voltage at the LDO5 pin falls below the lower UVLO
threshold and subsequently rises above the upper one).
If the MODE pin is high (i.e. connected to AVCC), the LED7706 behaves in a different
manner: the open row is excluded from the control loop and the device continues to work
properly with the remaining rows. The FAULT pin is not affected. Thus, if less than six rows
are used in the application, the MODE pin must be set high.
Figure 15 shows an example of open channel detection in case of MODE connected to
AVCC.
At the point marked as “1” in Figure 15, the row opens (row current drops to zero). From this
point on the output voltage is increased as long as the output voltage reaches the floating
row detection threshold (see Section 5.1.3 on page 13). Then (point marked as “2”) the
faulty row is disconnected and the device keeps on working only with the remaining rows.
Figure 15. Open channel detection (MODE to AVCC)
2
1
22/46
LED7706
5.3.4
Operation description
Shorted LED fault
When a LED is shorted, the voltage across the related current generator increases of an
amount equal to the missing voltage drop of the faulty LED. Since the feedback voltage on
each active generator is constantly compared with a fault threshold VTH,FAULT, the device
detects the faulty condition and acts according to the MODE pin status.
If the MODE pin is low, the fault threshold is VTH,FAULT = 3.4 V. When the voltage across a
row is higher than this threshold, the FAULT pin is set low and the device is turned off. The
internal logic latches this status until the EN pin is toggled or a POR is performed.
In case the MODE pin is connected to AVCC, the fault threshold is set to 6 V. The LED7706
simply disconnects the rows whose voltage is higher than the threshold and the FAULT pin
is forced low. This option is also useful to avoid undesired triggering of the shorted-LED
protection simply due to the high voltage drop spread across the LEDs.
Figure 16 shows an example of shorted LED detection in case MODE is connected to GND.
At the point marked as “1” in Figure 16 one LED fails becoming a short-circuit. The voltage
across the current generator of the channel where the failed LED is connected increases by
an amount equal to the forward voltage of the faulty LED. Since the voltage across the
current generator is above the threshold (3.4 V in this case), the device is turned off and the
fault pin is set low (point “2”).
Figure 16. Shorted LED detection (MODE to GND)
1
2
23/46
Application information
LED7706
6
Application information
6.1
System stability
The boost section of the LED7706 is a fixed frequency, current-mode converter. During
normal operation, a minimum voltage selection circuit compares all the voltage drops across
the active current generators and provides the minimum one to the error amplifier. The
output voltage of the error amplifier determines the inductor peak current in order to keep its
inverting input equal to the reference voltage (400 mV typ). The compensation network
consists of a simple RC series (RCOMP - CCOMP) between the COMP pin and ground.
The calculation of RCOMP and CCOMP is fundamental to achieve optimal loop stability and
dynamic performance of the boost converter and is strictly related to the operating
conditions.
6.1.1
Loop compensation
The compensation network can be quickly calculated using equations 12 to 16. Once both
RCOMP and CCOMP have been determined, a fine-tuning phase may be required in order to
get the optimal dynamic performance from the application.
The first parameter to be fixed is the switching frequency. Normally, a high switching
frequency allows reducing the size of the inductor and positively affects the dynamic
response of the converter (wider bandwidth) but increases the switching losses. For most of
applications, the fixed value (660 kHz) represents a good trade-off between power
dissipation and dynamic response, allowing to save an external resistor at the same time. In
low-profile applications, the inductor value is often kept low to reduce the number of turns;
an inductor value in the 4.7 µH-15 µH range is a good starting choice.
In order to avoid instability due to interaction between the DC-DC converter's loop and the
current generators' loop, the bandwidth of the boost should not exceed the bandwidth of the
current generators. A unity-gain frequency (fU) in the order of 30-40 kHz is acceptable. Also,
take care not to exceed the CCM-mode right half-plane zero (RHPZ).
Equation 12
fU ≤ 0.2 ⋅ FSW
Equation 13
2
⎛ VIN,min ⎞ ⎛ VOUT
⎜
⎟ ⎜
⎜ V
⎟ ⎜
2
M R
OUT ⎠ ⎝ IOUT
⎝
fU ≤ 0.2 ⋅
= 0. 2 ⋅
2π ⋅ L
2π ⋅ L
Equation 14 a
M=
24/46
VIN,min
VOUT
⎞
⎟
⎟
⎠
LED7706
Application information
Equation 14b
R=
VOUT
IOUT
Where VIN,min is the minimum input voltage and IOUT is the overall output current.
Note that, the lower the inductor value (and the higher the switching frequency), the higher
the bandwidth can be achieved. The output capacitor is directly involved in the loop of the
boost converter and must be large enough to avoid excessive output voltage drop in case of
a sudden line transition from the maximum to the minimum input voltages.
However a more significant requirement concerns the output voltage ripple.
The output capacitor should be chosen in accordance with the following expression:
Equation 15
COUT >
(IL,peak − IOUT )⋅ TOFF
2 ⋅ ΔVOUT,max
where ΔVOUT, max is the maximum acceptable output voltage ripple, IL, peak is the peak
inductor current, TOFF is the off-time of the switching cycle (for an extensive explanation see
Section 6.4.4 on page 31).
Once the output capacitor has been chosen, the RCOMP can be calculated as:
Equation 16
R COMP =
2π ⋅ fU ⋅ C
GM ⋅ gEA ⋅ M
Where GM = 2.7 S and gEA = 375 µS
Equation 16 places the loop bandwidth at fU. Then, the CCOMP capacitor is determined to
place the frequency of the compensation zero 5 times lower than the loop bandwidth:
Equation 17
C COMP =
1
2π ⋅ fZ ⋅ R COMP
Where fZ=fU/5.
In most of the applications an experimental approach is also very valid to compensate the
circuit. A simple technique to optimize different applications is to choose CCOMP = 4.7 nF
and to replace RCOMP with a 10 kΩ trimmer adjusting its value to properly damp the output
transient response. Insufficient damping will result in excessive ringing at the output and
poor phase margin.
Figure 17 (a and b) give an example of compensation adjustment for a typical application.
25/46
Application information
LED7706
Figure 17. Poor phase margin (a) and properly damped (b) load transient responses
a)
b)
Figure 18. Load transient response measurement set-up
6.8μH
VIN= 6V
C
VBOOST
IN
4.7μF
MLCC
FSW
OVSEL
LX
LDO5
SLOPE
VIN
AVCC
+5V
ROW1
BILIM
ROW2
RILIM
ROW3
LED7706
PGND
MODE
ROW6
SYNC
SGND
EN
ROW5
DIM
ROW4
COMP
FAULT
SS
RL =
Up to 10 WLEDs per row
VBST
50mA
500Hz
AM00607v1
26/46
LED7706
6.2
Application information
Thermal considerations
In order to prevent the device from exceeding the thermal shutdown threshold (150 °C), it is
important to estimate the junction temperature through the following equation:
Equation 18
TJ = TAmb + R th,JA ⋅ PD,tot
where TA is the ambient temperature, Rth,JA is the equivalent thermal resistance junction to
ambient and PD,tot is the power dissipated by the device.
The Rth,JA measured on the application demonstration board (described in Section 6.5)
is 42 °C/W.
The PD,tot has several contributions, listed below.
a) Conduction losses due to the RDS(on) of the internal power switch, equal to:\
Equation 19
2
PD,cond = RDSon ⋅ IIN
⋅ D ⋅ DDIM
where D is defined as:
Equation 20
D = 1−
VIN
VOUT
and DDIM is the duty cycle of the PWM dimming signal.
b) Switching losses due to the power MOSFET turn on and off, calculated as:
Equation 21
PD,sw = VOUT ⋅ IIN ⋅ fsw ⋅
(tr + t f )
⋅ DDIM
2
where tr and tf are the power MOSFET rise time and fall time respectively.
c) Current generators losses. This contribution is strictly related to the LEDs used in
the application. Only the contribution of the leading current generator (“master”
current generator) can be predicted, regardless of the LEDs forward voltage:
Equation 22
PGEN,Master = IROW ⋅ VIFB ⋅ DDIM
where IROW is the current flowing through the row, whereas VIFB is the voltage across the
master current generator (typically 400 mV).
The voltages across the other current generators depend on the spread of the LEDs forward
voltage. The worst case for power dissipation (maximum forward voltage LEDs in the master
row, minimum forward voltage LEDs in all other rows) can be estimated as:
27/46
Application information
LED7706
Equation 23
PGEN = IROW ⋅ (nROWs − 1) ⋅ (VIFB + ΔVf,LEDs ⋅ nLEDs ) ⋅ DDIM
where nROWs is the number of active rows, ΔVf,LEDs is the spread of the LEDs forward
voltage and nLEDs is the number of LEDs per row.
d)
LDO losses, due to the dissipation of the 5 V linear regulator:
Equation 24
PD,LDO = (VIN − VLDO ) ⋅ ILDO
The LED7706 is housed in a 24 leads 4x4-VFQFPN package with exposed pad that allows
good thermal performance. However it is also important to design properly the
demonstration board layout in order to assure correct heat dissipation.
Figure 19 shows a picture of the LED7706 application demonstration board taken using an
infrared camera. The chip temperature, in those application conditions, is kept below 50 °C.
Figure 19. Demonstration board thermographic analysis
VIN = 12V
I ROW = 20mA
VOUT = 34V
FSW = 660kHz
D DIM = 90%
T Amb = 30°C
6.3
Component selection
6.3.1
Inductor selection
Being the LED7706 mostly dedicated to backlighting, real-estate applications dictate severe
constrain in selecting the optimal inductor. The inductor choice must take into account
different parameters like conduction losses (DCR), core losses (ferrite or iron-powder),
saturation current and magnetic-flux shielding (core shape and technology).
The switching frequency of the LED7706 can be set in the 200 kHz-1 MHz range, allowing a
wide selecting room for the inductance value. Low switching frequencies takes to high
inductance value, resulting in significant DCR and size. On the other hand, high switching
frequencies result in significant core losses. The suggested range is 4.7-22 µH, even if the
28/46
LED7706
Application information
best trade off between the different loss contributions varies from manufacturer to
manufacturer.
A 6.8 µH inductor has been experimentally found as the most suitable for applications
running at a 660 kHz switching frequency.
Table 7.
6.3.2
Recommended inductors
Manufacturer
Part number
Description
Size
Coilcraft
LPS6235-682MLC
6.8 μH, 75 mΩ, 2.7 A
6x6 mm
Wurth
7440650068
6.8 μH, 33 mΩ, 3.6 A
10x10 mm
Capacitors selection
The input and output capacitors should have very low ESR (ceramic capacitors) in order to
minimize the ripple voltage. The boost converter of the LED7706 has been designed to
support ceramic capacitors. The required capacitance depends on the programmed LED
current and the minimum dimming frequency (the boost converter is off when the DIM pin is
low and the output capacitor is slowly discharged). Considering the worst case (i.e. 200 Hz
dimming frequency and 30 mA/channel), two 2.2 µF MLCCs are suitable for almost all
applications. Particular care must be taken when selecting the rated voltage and the
dielectric type of the output capacitors: 50 V rated MLCC may show a significant
capacitance drop when biased, especially in case of Y5V dielectric.
As in most of boost converters, the input capacitor is less critical, although it is necessary to
reduce the switching noise on the supply rail. The input capacitor is also important for the
internal LDO of the LED7706 and must be kept as close as possible to the chip. The rated
voltage of the input capacitor can be chosen according to the supply voltage range; a 10 µF
X5R MLCC is recommended.
Table 8.
6.3.3
Recommended capacitors
Manufacturer
Part number
Description
Package
Notes
Taiyo Yuden
UMK325BJ106KM-T
Ceramic, 35V, X5R, 20 %
SMD 1210
CIN
Murata
GRM31CR71H225KA88B
Ceramic, 50V, X7R, 20 %
SMD 1206
COUT
Murata
GRM31CR71H475KA88B
Ceramic, 50V, X7R, 20 %
SMD 1206
COUT
Flywheel diode selection
The flywheel diode must be a Schottky type to minimize the losses. This component is
subject to an average current equal to the output one and must sustain a reverse voltage
equal to the maximum output rail voltage. Considering all the channels sinking 30mA each
(i.e. 180 mA output current) and the maximum output voltage (36 V), the STP1L40M
(If,ave = 1 A, Vr = 40 V) diode is a good choice. Smaller diodes can be used in applications
involving lower output voltage and/or lower output current.
29/46
Application information
6.4
LED7706
Design example
In order to help the design of an application using the LED7706, in this section a simple
step-by-step design example is provided.
A possible application could be the LED backlight in a 15” LCD panel using the LED7706.
Here below the possible application conditions are listed:
6.4.1
●
VIN = 12 ± 20 %
●
2 strings of 48 white LEDs (20 mA) each (arranged in 6 rows, 8 LEDs per row)
●
VF, LEDs = 3.5 V ± 200 mV
Switching frequency setting
To reduce the number of the external components, the default switching frequency is
selected (660 kHz typ.) by connecting the FSW pin to AVCC pin.
However, in case a different switching frequency is required, a resistor from FSW pin and
ground can be connected, according to the equation (5) in Section 5.1.5.
6.4.2
Row current setting
Considering the equation 10 in Section 5.2.1, the RRILIM resistor can be calculated as:
Equation 25
RRILIM =
KR
IROW
=
987 V
= 49.35kΩ
20 mA
The closest standard commercial value is 51 kΩ. The actual value of the row current will be
a little lower (19.3 mA).
6.4.3
Inductor choice
The boost section, as all DC-DC converters, can work in CCM (continuous conduction
mode) or in DCM (discontinuous conduction mode) depending on load current, input and
output voltage and other parameters, among which the inductor value.
In a boost converter it is usually preferable to work in DCM.
Once the load, the input and output voltage, and the switching frequency are fixed, the
inductor value defining the boundary between DCM and CCM operation can be calculated
as:
Equation 26
R 0 ⋅ D ⋅ (1 − D)
2 ⋅ FSW
2
LB =
where D is the duty-cycle defined as:
30/46
LED7706
Application information
Equation 27
D = 1−
⎧ 0.68 @ VIN,min = 9.6V
VIN
=⎨
VOUT ⎩0.52 @ VIN,max = 14.4V
whereas R0 is:
Equation 28
R0 =
VOUT
= 250Ω
IOUT
and
Equation 29
IOUT = 6 ⋅ IROW = 120mA
The output voltage in the above calculations is considered as the maximum value (LED with
the maximum forward voltage connected to the leading generator):
Equation 30
VOUT,max = 8 ⋅ VF,LEDs,max + 400mV = 30 V
Considering the input voltage range, the lower LB will be at the lower input voltage. Hence
the condition to assure the DCM operation becomes:
Equation 31
L < L B (VIN,min ) = 13.2μH
An inductor value of 6.8 µH could be a suitable value, considering also a margin from the
boundary condition.
It is important to highlight that the inductor choice involves not only the value itself but the
saturation current (higher than the current limit, see Section 6.4.4), the rated RMS current
(the compliance with the saturation current might be not enough; also the thermal
performances must be taken into account), the DCR (which affects the efficiency) and the
size (in some application might be a strict requirement).
However the DCR can’t be reduced keeping the size small. Hence a trade off between these
two requirements must be achieved according to the application.
6.4.4
Output capacitor choice
The choice of the output capacitor is mainly affected by the desired output voltage ripple.
Since the voltage across the LEDs can be considered almost constant, this ripple is
transferred across the current generators, affecting their dynamic response.
The output ripple can be estimated as (neglecting the contribution of ESR of COUT, very low
in case of MLCC):
31/46
Application information
LED7706
Equation 32
ΔVOUT =
(IL,peak − IOUT )⋅ TOFF `
2 ⋅ C OUT
where IL, peak is the inductor peak current (see Figure 20) calculated as:
Equation 33
IL,peak =
VIN ⋅ D ⎧ 1.044 A @ VIN,min = 9.6V
=⎨
Fsw ⋅ L ⎩0.914 A @ VIN,max = 14.4V
whereas D, working in DCM, is:
Equation 34
D=
2 ⋅ Fsw ⋅ L ⋅ M(M − 1) ⎧ 0.488 @ VIN,min = 9.6V
=⎨
R0
⎩0.285 @ VIN,max = 14.4V
defining M as:
Equation 35
M=
VOUT
VIN
⎧ 3.125 @ VIN,min = 9.6V
⎨
⎩2.083 @ VIN,max = 14.4V
Figure 20. Inductor current in DCM operation
IL
IL, peak
TON
TOFF
t
TSW = 1/FSW
AM00608v1
TOFF can be calculated as:
Equation 36
⎧ 348.5ns @ VIN,min = 9.6V
TOFF = TSW ⋅ D 2 = ⎨
⎩398.5ns @ VIN,max = 14.4V
defining D2 as:
32/46
LED7706
Application information
Equation 37
D2 =
2 ⋅ FSW ⋅ L ⋅ M ⎧ 0.23 @ VIN,min = 9.6V
=⎨
R 0 ⋅ (M − 1)
⎩0.263 @ VIN,max = 14.4V
The worst case for the output voltage ripple is when input voltage is lower (VIN,min = 9.6 V).
A simple way to select the COUT value is fixing a maximum voltage ripple.
In order to affect as less as possible the current generators, it would be better to fix the
maximum ripple lower than the typical voltage across the generators.
For example considering ΔVOUT lower than 80 mV (i.e. the 20 % of the voltage across the
leading generator), the required capacitance is:
Equation 38
COUT >
(IL,peak − IOUT )⋅ TOFF
2 ⋅ ΔVOUT,max
= 2.02μF
A margin from the calculated value should be taken into account because of the
capacitance drop due to the applied voltage when MLCCs are used.
A 4.7 µF MLCC can be a good choice for this application (two 2.2 μF MLCC in parallel can
be also a good solution).
In case a dimming duty cycle different from 100 % is used, a further contribution to the
capacitor discharge (during the off time of the dimming cycle) should be considered.
6.4.5
Input capacitor choice
The input capacitor of a boost converter is less critical than the output capacitor, due to the
fact that the inductor is in series with the input, and hence, the input current waveform is
continuous.
A low ESR capacitor is always recommended.
A capacitor of 10 µF is tentatively a good choice for most of the applications.
6.4.6
Over-voltage protection divider setting
The over-voltage protection (OVP) divider provides a partition of the output voltage to the
OVSEL pin. The OVP divider setting not only fixes the OVP threshold, but also the openchannel detection threshold (95 % of the OVP threshold).
The proper OVP divider setting can be calculated by the equation (3):
Equation 39
R 2 = R1 ⋅
1.234 V
(VOUT,MAX + 2V − 1.234 V)
where VOUT, MAX is the maximum output voltage considering the worst case (all LEDs with
the maximum VF = VF,max = 3.7 V on the same row):
33/46
Application information
LED7706
Equation 40
VOUT,OVP = nLED ⋅ VF,max + 400mV = 30 V
R1 can be chosen is in the order of hundreds of kilo-ohms to reduce the leakage current in
the resistor divider. For example, setting R1 = 510 kΩ leads to R2 = 21.89 kΩ. The closest
standard commercial value is R2 = 22 kΩ.
The correct selection of the OVP divider (and, as consequence, the open channel detection
threshold) must take into account the shorted LED fault threshold (see Section 5.3.4).
When the selected OVP threshold is too high, an undesired triggering of the shorted LED
detection circuitry may occur when a channel opens.
In fact, as explained in section 4.3.3, once a channel opens, the device reacts increasing the
output voltage and the voltage across the working current generators may reach the shorted
LED detection threshold before the open channel detection threshold.
6.4.7
Compensation network
For the compensation network, the suggestions provided in Section 6.1 are always valid.
In this condition, tentatively the following value of R3 and C8 (see Figure 23) are usually a
good choice for the loop stability:
R3 = 2.4 kΩ
C8 = 4.7 nF
6.4.8
Boost current limit
The boost current limit is set to protect the internal power switch against excessive current.
The slope compensation may reduce the programmed current limit. Hence, to take into
account this effect, as a rule of thumb, the current limit can be set as twice as much the
maximum inductor peak current (see Section 6.4.4):
IBOOST, PEAK > 2.09 A
Therefore, using equation (8) and choosing IBOOST, PEAK = 2.5 A, RBILIM will be:
Equation 41
RBILIM =
34/46
KB
IBOOST,PEAK
= 240kΩ
LED7706
6.4.9
Application information
Power dissipation estimate
As explained in Section 6.2, there are several contributions to the total power dissipation.
Neglecting the power dissipated by the LDO (surely less significant compared with the other
contributions), equation (19), (21), (22) and (23) help to estimate the overall power
dissipation.
Before starting the power dissipation estimate it is important to highlight that the following
calculations are considering the worst case (the actual value of the dissipated power would
require measurements). Therefore the power dissipation is estimated according to the
following assumptions:
1.
Minimum input voltage (9.6 V), which leads to maximum input current (and also D will
have the higher value, see Section 6.4.4);
2.
Maximum RDS(on) of the internal power MOSFET;
3.
LEDs in the row of the leading generator will have the maximum forward voltage,
whereas all other LEDs in the other rows will have the minimum forward voltage.
4.
100 % dimming signal duty cycle is considered.
The conduction and switching losses on the internal power switch can be calculated as:
Equation 42
2
PD,cond = RDSon ⋅ IIN
⋅ D ⋅ DDIM = 34mW
Equation 43
PD,sw = VOUT ⋅ IIN ⋅ fsw ⋅
(tr + t f )
⋅ DDIM = 111mW
2
where tr = tf = 15 ns
The power dissipation related to the current generators is given by:
Equation 44
PGEN,Master = IROW ⋅ VIFB ⋅ DDIM = 8mW
Equation 45
PGEN = IROW ⋅ (nROWs − 1) ⋅ (VIFB + ΔVf,LEDs ⋅ nLEDs ) ⋅ DDIM = 360mW
Equation 46
PD,tot ≅ PD,cond + PD,sw + PGEN,Master + PGEN = 513mW
The junction temperature can be estimated by equation (18) considering TA = 25 °C:
Equation 47
TJ = TAmb + R th,JA ⋅ PD,tot = 46.5°C
35/46
Application information
LED7706
In order to estimate also the efficiency, other contributions to the power dissipation must be
added to PD, tot (which represents only the power dissipated by the device), that is:
Equation 48
PDISS,Diode = VF,Diode ⋅ IIN ⋅ D 2 = 34.5mW
where VF, Diode = 0.4 V
Equation 49
2
2
PDISS,Ind = DCR ⋅ IInd
,RMS ≅ DCR ⋅ IIN = 11.2mW
where DCR = 80 mΩ (typical DCR of the recommended inductors).
Therefore the total dissipated power is:
Equation 50
PDISS,TOTAL = PD,tot + PDISS,Diode + PDISS,Ind = 559.1mW
Considering the input power as the result of input voltage multiplied by the input current, the
estimated efficiency is:
Equation 51
η=
Note:
36/46
PIN − PDISS,TOT
PIN
= 0.845
It is important to remind that the previous calculations consider the worst case, especially for
the power dissipated on the current generators.
Statistical analysis (confirmed by bench measurements) shows that the series connection of
more LEDs on each channel leads to compensation effects.
The hypothesis 3 above mentioned is thus rather unlikely.
Therefore PGEN is significantly lower and the overall efficiency is typically around 90 %.
LED7706
6.5
Application information
Layout consideration
1.
A careful PCB layout is important for proper operation. In this section some guidelines
are provided in order to achieve a good layout.
2.
The device has two different ground pins: signal ground (SGND) and power ground
(PGND). The PGND pin handles the switching current related to the boost section; for
this reason the PCB traces should be kept as short as possible and with adequate
width.
3.
The signal ground is the return for the device supply and the current generators and
can be connected to the thermal pad.
4.
The heat dissipation area (adequate to the application conditions) should be placed
backside respect to the device and with the lowest thermal impedance possible (i.e.
PCB traces in the backside should be avoided). The dissipation area is thermally and
electrically connected to the thermal pad by several vias (nine vias are recommended).
5.
The signal and power grounds must be connected together in a single point as close as
possible to the PGND pin to reduce ground loops.
6.
The R-C components of the compensation network should be placed as close as
possible to the COMP pin in order to avoid noise issue and instability of the
compensation.
7.
Noise sensitive signals (i.e. feedbacks and compensation) should be routed as short as
possible to minimize noise collection. The LED7706 pinout makes it easy to separate
power components (e.g. inductor, diode) from signal ones.
8.
The LX switching node should have and adequate width for high efficiency.
9.
The critical power path inductor-LX-PGND must be as short as possible by mounting
the inductor, the diode and COUT as close as possible each other.
10. The capacitors of the compensated divider connected to the OVSEL pin should be
placed as close as possible to the OVSEL pin.
11. In order to assure good performance in terms of row current accuracy/mismatch, the
PCB traces from the rows pins to the LEDs should have similar length and width.
12. The capacitors of the filter connected to LDO5 and VIN pins should be mounted as
close as possible to the mentioned pins
Figure 21 and Figure 22 shows the demonstration board layout (top view and bottom view
respectively).
37/46
Application information
LED7706
Figure 21. Demonstration board layout (top view)
Figure 22. Demonstration board layout (bottom view)
Figure 23 shows the LED7706 demonstration board application circuit, whereas Table 9 lists
the used components and their value.
38/46
LED7706
Application information
Figure 23. LED7706 demonstration board schematic
AM00609v1
39/46
Application information
Table 9.
LED7706
LED7706 demonstration board component list
Component
Description
Package
Part number
MFR
Value
C1
Ceramic, 35V
X5R, 20%
SMD 1210
UMK325BJ106KM-T
Taiyo Yuden
10 µF
SMD 1206
GRM31CR71H225KA88B
C2,C3
C4
Ceramic, 50V
X7R, 20%
2.2 µF
Murata
SMD 1206
GRM31CR71H225KA88B
N.M.
C5
1 µF
C6
100 nF
C7
3.3 nF
C8
C9
4.7 nF
Ceramic, 25V
X5R, 20%
SMD 0603
Standard
N.M.
C10
220 pF
C11
4.7 nF
C12
N.M.
C13
15 pF
R1
510 kΩ
R2
16 kΩ
R3
R4
Chip resistor
0.1 W, 1%
2.4 kΩ
SMD 0603
Standard
4.7 Ω
R5
330 kΩ
R6
51 kΩ
R7
180 kΩ
R8
680 kΩ
R9, R10
R11
Chip resistor
0.1 W, 1%
100 kΩ
SMD 0603
Standard
1.2 kΩ
R12
N.M.
R13
N.M.
L1
6u8, 75 mΩ, 2.7 A
6x6 mm
LPS6235-682MLC
Coilcraft
6.8 µF
D1
Schottky, 40 V, 1 A
DO216-AA
STPS1L40M
ST
STPS1L40M
D2
Red LED, 3 mA
SMD 0603
Standard
D3
Signal Schottky
SOD-523
BAS69
N.M.
U1
Integrated circuit
QFN4x4
ST
LED7706
J2
PCB pad jumper
J8
Header 8
SIL 8
Standard
SW1, SW2
Jumper 3
SIL 3
Standard
SW3
Push button
6x6 mm
40/46
LED7706
FSM4JSMAT
TYCO
LED7706
7
Electrical characteristics
Electrical characteristics
Figure 24. Efficiency versus DIM duty cycle,
VIN = 6 V, 6 rows, 10 white LEDs
(20 mA) in series
Figure 25. Efficiency versus DIM duty cycle,
VIN = 12 V, 6 rows, 10 white LEDs
(20 mA) in series
Figure 26. Efficiency versus DIM duty cycle,
VIN = 18 V, 6 rows, 10 white LEDs
(20 mA) in series
Figure 27. Efficiency versus DIM duty cycle,
VIN = 24 V, 6 rows, 10 white LEDs
(20 mA) in series
Figure 28. Soft-start waveforms (EN, SS, and
VOUT monitored)
Figure 29. Boost section switching signals
(LX, SYNC and inductor current
monitored), VIN = 12 V, 10 LEDs
41/46
Electrical characteristics
Figure 30. Dimming waveforms
(FDIM = 200 Hz)
LED7706
Figure 31. Dimming waveforms (FDIM = 1 kHz)
Figure 32. Dimming waveforms (FDIM = 5 kHz) Figure 33. Dimming waveforms (FDIM = 20 kHz)
Figure 34. Dimming waveforms
(TDIM,ON = 10 µs)
42/46
Figure 35. Dimming waveforms with the
minimum dimming on time (500 ns)
LED7706
8
Package mechanical data
Package mechanical data
In order to meet environmental requirements, ST offers these devices in different grades of
ECOPACK® packages, depending on their level of environmental compliance. ECOPACK®
specifications, grade definitions and product status are available at: www.st.com.
ECOPACK® is an ST trademark.
43/46
Package mechanical data
Table 10.
LED7706
VFQFPN-24 4 mm x 4 mm mechanical data
mm
Dim.
Min.
Typ.
Max.
A
0.80
0.90
1.00
A1
0.00
0.02
0.05
A3
0.20
b
0.18
0.25
0.30
D
3.85
4.00
4.15
D2
2.40
2.50
2.60
E
3.85
4.00
4.15
E2
2.40
2.50
2.60
e
L
0.50
0.30
ddd
Figure 36. Package dimensions
44/46
0.40
0.50
0.08
LED7706
9
Revision history
Revision history
Table 11.
Document revision history
Date
Revision
08-Feb-2008
1
Initial release
2
Added: Chapter 3 on page 7, Chapter 3 on page 7 and Chapter 3 on
page 7
Updated: Chapter 3 on page 7, Chapter 3 on page 7, Chapter 3 on
page 7, Table 4, Table 5, Figure 3, Figure 4, Figure 7, Figure 23 and
Table 9
09-Apr-2009
Changes
45/46
LED7706
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2009 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
46/46
工商网监
湘ICP备2023018690号
