LM101AN

LM101A - LM201A LM301A SINGLE OPERATIONAL AMPLIFIER . . . . INPUT OFFSET VOLTAGE INPUT BIAS CURRENT INPUT OFFSET CURRENT SLEW RATE AS INVERTING AMPLIFIER LM101A LM201A 0.7mV 25nA 1.5nA 10V/ µs LM301A 2mV 70nA 2nA 10V/µs N DIP8 (Plastic Package) D SO8 (Plastic Micropackage) DESCRIPTION The LM101A is a general-purpose operational amplifier which offers many features : supply voltages from ±5V to ±22V, low current drain, overload protection on the inputand output,no latch-up when the common-mode range is exceeded, free from oscillations and compensationwith a single 30pFcapacitor. It has advantages over internally compensated amplifiers in that the compensation can be tailored to the particular application : slew rate of 10V/µs and bandwidth of 3.5MHz can be easily achieved. ORDER CODES Part Number LM101A LM201A LM301A Temperature Range -55 C, +125 C -40oC, +105oC 0 C, +70 C o o o o Package N • • • D • • • Example : LM201AN PIN CONNECTIONS (top view) 1 2 3 4 8 7 6 5 1 - Balance - compensation 1 2 - Inverting input 3 - Non-inverting input 4 - VCC5 - Balance 6 - Output 7 - VCC+ 8 - Compensation 2 October 1995 1/11 LM101A - LM201A - LM301A SCHEMATIC DIAGRAM ABSOLUTE MAXIMUM RATINGS Symbol Vcc Vid Vi Ptot Parameter Supply Voltage Differential Input Voltage Input Voltage Power Dissipation Output Short-circuit Duration Toper Tstg Operating Free Air Temperature Range Storage Temperature Range -55 to +125 -65 to +150 N Suffix D Suffix LM101A LM201A ±22 ±30 ±15 500 300 Infinite -40 to +105 -65 to +150 0 to +70 -65 to +150 o o LM301A Unit V V V mW C C 2/11 LM101A - LM201A - LM301A ELECTRICAL CHARACTERISTICS LM301A 0oC < Tamb < +70oC LM201A -40oC < Tamb < +105oC LM101A -55oC < Tamb < +125oC Symbol Vio Parameter Input Offset Voltage (RS ≤ 10kΩ) o Tamb = +25 C Tmin. ≤ Tamb ≤ Tmax. Input Offset Voltage Drift Tmin. ≤ Tamb ≤ Tmax. Input Bias Current o Tamb = +25 C Tmin. ≤ Tamb ≤ Tmax. Input Offset Current o Tamb = +25 C Tmin. ≤ Tamb ≤ Tmax. Input Offset Current Drift o 25 C ≤ Tamb ≤ Tmax. Tmin. ≤ Tamb ≤ Tmax. Large Signal Voltage Gain * (VO ≤ 10V, RL = 2kΩ) o Tamb = +25 C Tmin. ≤ Tamb ≤ Tmax. Supply Voltage Rejection Ratio (RS ≤ 10kΩ) o Tamb = +25 C Tmin. ≤ Tamb ≤ Tmax. Supply Current, no load Tamb = +25oC Tmin. ≤ Tamb ≤ Tmax. Input Common Mode Voltage Range (VCC = ±20V) Tamb = +25oC Tmin. ≤ Tamb ≤ Tmax. Common-mode Rejection Ratio (RS ≤ 10kΩ) Tamb = +25oC Tmin. ≤ Tamb ≤ Tmax. Output Short-circuit Current * o Tamb = +25 C Output Voltage Swing * Tamb = +25oC Tmin. ≤ Tamb ≤ Tmax. RL RL RL RL = = = = 10kΩ 2kΩ 10kΩ 2kΩ ±15 ±15 ±5V ≤ VCC ≤ ±20V ±5V ≤ VCC ≤ ±20V ±5V ≤ VCC ≤ ±20V LM101A - LM201A Min. Typ. 0.7 3 Max. 2 3 15 C1 = 30pF C1 = 30pF C1 = 30pF LM301A Min. Typ. 2 6 Max. 7.5 10 30 µV/ C nA o Unit mV DV io Iib 25 75 100 10 20 100 200 70 250 300 nA 50 70 pA/oC 300 600 V/mV Iio 1.5 2 DIio 10 20 10 20 Avd 50 25 100 25 15 100 dB SVR 80 80 96 70 70 3 3 ±15 ±15 96 mA ICC 1.8 1.8 3 3 V Vicm CMR dB 80 80 10 12 10 12 10 96 70 70 50 10 12 10 12 10 96 mA 30 14 13 30 14 13 50 V IOS ±VOPP 3/11 LM101A - LM201A - LM301A ELECTRICAL CHARACTERISTICS (continued) Symbol SR tr KOV Zi Ro GBP Parameter Slew Rate (Vi = ±10V, RL =2kΩ, CL= 100pF, o Tamb = 25 C, unity gain) - (note 1) * Rise Time (Vi = ±20µV, RL = 2kΩ, CL = 100pF, Tamb = 25oC, unity gain) * Overshoot (V i = 20mV, RL = 2kΩ, CL = 100pF, o Tamb = 25 C, unity gain) Input Impedance * Output Resistance * Gain Bandwidth Product * (Vi = 10mV, RL = 2kΩ, C L= 100pF, f = 100kHz, Tamb = 25oC) Total Harmonic Distortion (f = 1kHz, AV = 20dB, RL =2kΩ, VO = 2VPP, o CL = 100pF, Tamb = 25 C) Equivalent Input Noise Voltage (f = 1kHz, Rs = 100Ω) 0.5 1.5 LM101A - LM201A Min. 0.25 Typ. 0.5 0.3 5 4 75 1 0.5 1.5 Max. Min. 0.25 LM301A Typ. 0.5 0.3 5 4 75 1 % 0.015 25 0.015 25 nV  Hz √ MΩ Ω MHz µs % Max. Unit V/µs THD en Notes : 1. May be i mproved up to 10V / µ s in invert ing ampli fier configuration * => V CC = ± 15V T amb = +25 o C (unl ess ot herwise speci fied) 4/11 LM101A - LM201A - LM301A 5/11 LM101A - LM201A - LM301A S INGLE POLE COMPENSATION FEED FORWARD COMPENSATION 6/11 LM101A - LM201A - LM301A 7/11 LM101A - LM201A - LM301A 8/11 LM101A - LM201A - LM301A 9/11 LM101A - LM201A - LM301A P ACKAGE MECHANICAL DATA 8 PINS - PLASTIC DIP Dim. A a1 B b b1 D E e e3 e4 F i L Z Millimeters Min. 0.51 1.15 0.356 0.204 7.95 2.54 7.62 7.62 6.6 5.08 3.18 3.81 1.52 0.125 1.65 0.55 0.304 10.92 9.75 0.313 Typ. 3.32 Max. Min. 0.020 0.045 0.014 0.008 Inches Typ. 0.131 Max. 0.065 0.022 0.012 0.430 0.384 0.100 0.300 0.300 0260 0.200 0.150 0.060 10/11 LM101A - LM201A - LM301A P ACKAGE MECHANICAL DATA 8 PINS - PLASTIC MICROPACKAGE (SO) Dim. A a1 a2 a3 b b1 C c1 D E e e3 F L M S Min. 0.1 0.65 0.35 0.19 0.25 4.8 5.8 Millimeters Typ. Max. 1.75 0.25 1.65 0.85 0.48 0.25 0.5 45 (typ.) 5.0 6.2 o Min. 0.004 0.026 0.014 0.007 0.010 0.189 0.228 Inches Typ. Max. 0.069 0.010 0.065 0.033 0.019 0.010 0.020 0.197 0.244 1.27 3.81 3.8 0.4 4.0 1.27 0.6 8 (max.) o 0.050 0.150 0.150 0.016 0.157 0.050 0.024 Information furnished is believed to be accurate and reliable. However, SGS-THOMSON Microelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of SGS-THOMSON Microelectronics. Specification mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. SGS-THOMSON Microelectronics products are not authorized for use as critical componen ts in life support devices or systems without express written approval of SGS-THOMSON Microelectronics. ORDER CODE : © 1995 SGS-THOMSON Microelectronics – Printed in Italy – All Rights Reserved SGS-THOMSON Microelectronics GROUP OF COMPANIES Australia - Brazil - Canada - China - France - Germany - Hong Kong - Italy - Japan - Korea - Malaysia - Malta - Morocco The Netherlands - Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A. 11/11