LM201AN

LM101A-LM201A LM301A SINGLE OPERATIONAL AMPLIFIERS LM101A LM201A LM301A s INPUT OFFSET VOLTAGE 0.7mV s INPUT BIAS CURRENT 25nA 2mV 70nA 2nA N DIP8 (Plastic Package) s INPUT OFFSET CURRENT 1.5nA AMPLIFIER DESCRIPTION s SLEW RATE AS INVERSING10V/µs 10V/µs The LM101A is a general purpose operational amplifier which offers many features: supply voltages from ±5V to ±22V, low current drain, overload protection on the input and output, no latch-up when the common-mode range is exceeded, free from oscillations and compensation with a single 30pF capacitor. It has advantages over internally compensated amplifiers in that the compensation can be tailored to the particular application: slew rate of 10V/µs and bandwidth of 3.5MHz can be easily achieved. ORDER CODE Package Part Number Temperature Range N LM101A -55°C, +125°C LM201A -40°C, +105°C LM301A 0°C, +70°C Example : LM201AN • • • D • • • D SO8 (Plastic Micropackage) PIN CONNECTIONS (top view) 1 2 3 4 5 - Balance 6 - Output 7 - VCC+ 8 7 6 5 N = Dual in Line Package (DIP) D = Small Outline Package (SO) - also available in Tape & Reel (DT) 1234- Balance, compensation Inverting input Non-inverting input VCC- 8 - Compensation 2 December 2001 1/11 LM101A - LM201A - LM301A SCHEMATIC DIAGRAM ABSOLUTE MAXIMUM RATINGS Symbol VCC Vi Vid Ptot Toper Tstg Supply voltage Input Voltage Differential Input Voltage Power Dissipation Output Short-circuit Duration Opearting Free-air Temperature Range Storage Temperature Range -55 to +125 N Suffix D Suffix Parameter LM101A LM201A ±22 ±15 ±30 500 300 Infinite -40 to +105 -65 to +150 0 to +70 LM301A Unit V V V mW °C °C 2/11 LM101A - LM201A - LM301A ELECTRICAL CHARACTERISTICS ±5V ≤ VCC ≤ ±20V, C1 = 30pF, Tamb = 25°C (unless otherwise specified) LM101A - LM201A Symbol Parameter Min. Vio Input Offset Voltage (RS ≤ 10kΩ) Tamb = +25°C Tmin ≤ Tamb ≤ Tmax Input Offset Voltage Drift Tmin ≤ Tamb ≤ Tmax Input Bias Current - note Tamb = +25°C Tmin ≤ Tamb ≤ Tmax Input Offset Current Tamb = +25°C Tmin ≤ Tamb ≤ Tmax Input Offset Current Drift Tmin ≤ Tamb ≤ 25°C Tmin ≤ Tamb ≤ Tmax Large Signal Voltage Gain * VO ≤ 10V, RL = 2kΩ) Tamb = +25°C Tmin ≤ Tamb ≤ Tmax Supply Voltage Rejection Ratio (Rs ≤ 10kΩ) Tamb = +25°C Tmin ≤ Tamb ≤ Tmax Supply Current, no load Tamb = +25°C Tmin ≤ Tamb ≤ Tmax Input Common Mode Voltage Range (VCC = ±20V) Tamb = +25°C Tmin ≤ Tamb ≤ Tmax Common Mode Rejection Ratio (Rs ≤ 10kΩ) Tamb = +25°C Tmin ≤ Tamb ≤ Tmax Output Short-circuit Current * Tamb = +25°C Output Voltage Swing * Tamb = +25°C ±VOPP Tmin ≤ Tamb ≤ Tmax RL = RL = RL = RL = 10kΩ 2kΩ 10kΩ 2kΩ Typ. 0.7 Max. 2 3 15 75 100 10 20 100 200 Min. Typ. 2 Max. 7.5 10 30 250 300 50 70 300 600 mV µV/°C LM301A Unit DVio 3 25 6 70 Iib nA Iio 1.5 2 nA DIIio 10 20 10 20 pA/°C Avd 50 25 80 80 100 25 15 70 70 3 3 100 V/mV SVR 96 96 dB ICC 1.8 1.8 3 3 mA Vicm ±15 ±15 ±15 ±15 V CMR 80 80 10 12 10 12 10 0.25 96 70 70 50 10 12 10 12 10 0.25 96 dB IOS 30 14 13 30 14 13 50 mA V SR Slew Rate (Vi = ±10V, RL = 2kΩ,CL = 100pF, unity gain) - 1) 0.5 0.5 V/µs 3/11 LM101A - LM201A - LM301A LM101A - LM201A Symbol Parameter Min. tr KOV Zi GBP Rise (Vi = ±20mV, RL = 2kΩ,CL = 100pF, unity gain) Overshoot (Vi = 20mV, RL = 2kΩ,CL = 100pF, unity gain) Input Impedance * Gain Bandwidth Product * (Vi = 10mV, RL = 2kΩ,CL = 100pF, f = 100KHz) Total Harmonic Distortion (f = 1kHz, Av = 20dB, RL = 2kΩ, Vo = 2Vpp, CL = 100pF) Equivalent Input Noise Voltage f = 1kHz, Rs = 100Ω 1.5 0.5 Typ. 0.3 5 4 1 1.5 0.5 Max. Min. LM301A Unit Typ. 0.3 5 4 1 Max. µs % MΩ MHz THD 0.015 0.015 % nV ----------Hz en 25 25 1. May be improved up to 10V/µs in inverting amplifier configuration * ==> VCC = ±15V, T amb = +25°C (unless otherwise specified) 4/11 LM101A - LM201A - LM301A 5/11 LM101A - LM201A - LM301A SINGLE POLE COMPENSATION FEED FORWARD COMPENSATION 6/11 LM101A - LM201A - LM301A 7/11 LM101A - LM201A - LM301A 8/11 LM101A - LM201A - LM301A 9/11 LM101A - LM201A - LM301A PACKAGE MECHANICAL DATA 8 PINS - PLASTIC DIP Millimeters Dim. Min. A a1 B b b1 D E e e3 e4 F i L Z 0.51 1.15 0.356 0.204 7.95 2.54 7.62 7.62 6.6 5.08 3.81 1.52 Typ. 3.32 1.65 0.55 0.304 10.92 9.75 0.020 0.045 0.014 0.008 0.313 Max. Min. Inches Typ. 0.131 0.065 0.022 0.012 0.430 0.384 0.100 0.300 0.300 0260 0.200 0.150 0.060 Max. 3.18 0.125 10/11 LM101A - LM201A - LM301A PACKAGE MECHANICAL DATA 8 PINS - PLASTIC MICROPACKAGE (SO) L C a3 c1 a2 A s e3 E D M 8 5 F 1 4 Millimeters Dim. Min. A a1 a2 a3 b b1 C c1 D E e e3 F L M S 0.1 0.65 0.35 0.19 0.25 4.8 5.8 1.27 3.81 3.8 0.4 4.0 1.27 0.6 8° (max.) 0.150 0.016 Typ. Max. 1.75 0.25 1.65 0.85 0.48 0.25 0.5 45° (typ.) 5.0 6.2 0.189 0.228 Min. 0.004 0.026 0.014 0.007 0.010 a1 b Inches Typ. Max. 0.069 0.010 0.065 0.033 0.019 0.010 0.020 0.197 0.244 0.050 0.150 0.157 0.050 0.024 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. © The ST logo is a registered trademark of STMicroelectronics © 2001 STMicroelectronics - Printed in Italy - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - Canada - China - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States © http://www.st.com b1 11/11