LM2904W, LM2904AW
Low power dual operational amplifier
IV
E
Datasheet — production data
Features
Frequency compensation implemented
internally
■
Large DC voltage gain: 100 dB
■
Wide bandwidth (unity gain): 1.1 MHz
(temperature compensated)
■
Very low supply current/op (500 µA per
channel)
■
Low input bias current: 20 nA (temperature
compensated)
■
Low input offset current: 2 nA
■
Input common-mode voltage range includes
negative rail
■
Differential input voltage range equal to the
power supply voltage
■
ESD internal protection: 2 kV
■
Automotive qualification
-I
P
TSSOP8
(Thin shrink small outline package)
Pin connections (top view)
Output A
Inverting input A
TI
VE
The LM2904W and LM2904AW circuits consist of
two independent, high gain operational amplifiers
which employ internal frequency compensation
and are designed specifically for automotive and
industrial control systems. They operate from a
single power supply over a wide range of
voltages. The low power supply drain is
independent of the magnitude of the power
supply voltage.
IN
AC
D
SO-8
(Plastic micropackage)
E
IV
-I
Description
CT
Large output voltage swing 0 V to
(VCC+ - 1.5 V)
N
DIP8
(Plastic package)
NA
■
NA
CT
■
Non-inverting input A
VCC
-
VCC+
Output B
Inverting input B
Non-inverting input B
supply. In linear mode, the input common mode
voltage range includes ground. The output
voltage can also swing to ground even though
operated from a single power supply.
Application areas include transducer amplifiers,
DC gain blocks, and all the conventional op-amp
circuits which now can be more easily
implemented in single power supply systems. For
example, these circuits can be directly supplied
from standard +5 V which is used in logic systems
and easily provides the required interface
electronics without requiring any additional power
February 2013
This is information on a product in full production.
Doc ID 9893 Rev 11
1/21
www.st.com
21
Contents
LM2904W, LM2904AW
Contents
Schematic diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2
Absolute maximum ratings and operating conditions . . . . . . . . . . . . . 4
3
Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
NA
CT
IV
E
1
Typical single-supply applications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Important note concerning this macromodel . . . . . . . . . . . . . . . . . . . . . . 13
4.2
Macromodel code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
-I
4.1
Package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
DIP8 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5.2
SO-8 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
5.3
TSSOP8 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
E
5.1
IV
5
Macromodel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
CT
4
Ordering information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
7
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
IN
AC
TI
VE
-I
NA
6
2/21
Doc ID 9893 Rev 11
LM2904W, LM2904AW
Schematic diagram
Schematic diagram (1/2 LM2904W, LM2904AW)
TI
VE
-I
NA
CT
IV
E
-I
NA
CT
IV
E
Figure 1.
IN
AC
1
Schematic diagram
Doc ID 9893 Rev 11
3/21
Absolute maximum ratings and operating conditions
LM2904W, LM2904AW
2
Absolute maximum ratings and operating conditions
Table 1.
Absolute maximum ratings (AMR)
VCC
Parameter
Value
IV
E
Symbol
Supply voltage(1)
+32
Vid
Differential input voltage
Vin
Input voltage
(2)
-0.3 V to VCC + 0.3
Storage temperature range
Maximum junction temperature
50
mA
Tstg
Storage temperature range
85
125
120
°C
°C/W
41
40
37
-65 to +150
°C
2000
200
1500
V
NA
CT
IV
E
Rthjc
Thermal resistance junction to case(5)
DIP8
SO-8
TSSOP8
HBM: human body
MM: machine model(7)
CDM: charged device model(8)
s
150
Rthja
model(6)
Infinite
-65 to +150
Thermal resistance junction to ambient(5)
DIP8
SO-8
TSSOP8
ESD
NA
CT
Tj
(4)
-I
Tstg
Input current
V
-0.3 V to VCC + 0.3
Output short-circuit duration(3)
Iin
Unit
1. All voltage values, except differential voltage are with respect to network ground terminal.
2. Differential voltages are the non-inverting input terminal with respect to the inverting input terminal.
-I
3. Short-circuits from the output to VCC can cause excessive heating if VCC+ > 15 V. The maximum output current is
approximately 40 mA, independent of the magnitude of VCC. Destructive dissipation can result from simultaneous shortcircuits on all amplifiers.
TI
VE
4. This input current only exists when the voltage at any of the input leads is driven negative. It is due to the collector-base
junction of the input PNP transistor becoming forward biased and thereby acting as input diode clamps. In addition to this
diode action, there is also NPN parasitic action on the IC chip. This transistor action can cause the output voltages of the
Op-amps to go to the VCC voltage level (or to ground for a large overdrive) for the time during which an input is driven
negative. This is not destructive and normal output is restored for input voltages above -0.3 V.
5. Short-circuits can cause excessive heating and destructive dissipation. Rth are typical values.
6. Human body model: 100 pF discharged through a 1.5 kΩ resistor between two pins of the device, done for all couples of pin
combinations with other pins floating.
IN
AC
7. Machine model: a 200 pF cap is charged to the specified voltage, then discharged directly between two pins of the device
with no external series resistor (internal resistor < 5 Ω), done for all couples of pin combinations with other pins floating.
8. Charged device model: all pins plus package are charged together to the specified voltage and then discharged directly to
the ground.
4/21
Doc ID 9893 Rev 11
LM2904W, LM2904AW
Operating conditions
Symbol
Parameter
Supply voltage
Vicm
Common mode input voltage range
Tmin ≤ Tamb ≤ Tmax
Toper
Operating free-air temperature range
Unit
3 to 30
VCC+ - 1.5
VCC+ - 2
V
-40 to +125
°C
IN
AC
TI
VE
-I
NA
CT
IV
E
-I
NA
CT
VCC
Value
IV
E
Table 2.
Absolute maximum ratings and operating conditions
Doc ID 9893 Rev 11
5/21
LM2904W, LM2904AW
3
Electrical characteristics
Table 3.
VCC+ = 5 V, VCC- = Ground, VO = 1.4 V, Tamb = 25 °C
(unless otherwise specified)
Symbol
DIio
Input offset voltage drift
Input offset current
Tmin ≤ Tamb ≤ Tmax
Input offset current drift
current(2)
Input bias
Tmin ≤ Tamb ≤ Tmax
Avd
Large signal voltage gain
VCC+ = +15 V, RL = 2 kΩ, Vo = 1.4 V to 11.4 V
Tmin ≤ Tamb ≤ Tmax
SVR
Supply voltage rejection ratio
RS ≤10 kΩ
Tmin ≤ Tamb ≤ Tmax
CT
IV
Iib
Max.
2
1
7
2
9
4
30
µV/°C
2
30
40
nA
10
300
pA/°C
20
150
200
nA
100
V/mV
65
65
100
dB
0.7
70
60
85
Isource
Output short-circuit current
VCC+ = +15 V, Vo = +2 V, Vid = +1 V
20
40
Output sink current
VO = 2 V, VCC+ = +5 V
VO = +0.2 V, VCC+ = +15 V
10
12
20
50
High level output voltage
VCC+ = + 30 V
RL = 2 kΩ
Tmin ≤ Tamb ≤ Tmax
RL = 10 kΩ
Tmin ≤ Tamb ≤ Tmax
26
26
27
27
IN
AC
TI
VE
-I
Common-mode rejection ratio
RS = 10 kΩ
Tmin ≤ Tamb ≤ Tmax
VOH
VOL
6/21
Low level output voltage
RL = 10 kΩ
Tmin ≤ Tamb ≤ Tmax
1.2
2
mA
dB
60
mA
mA
µA
V
27
28
5
Doc ID 9893 Rev 11
mV
7
CMR
Isink
Unit
50
25
Supply current, all Amp, no load
VCC = +5 V
Tmin ≤ Tamb ≤ Tmax, VCC = +30 V
NA
ICC
Typ.
NA
CT
Iio
Input offset voltage(1)
Tamb = 25 ° C LM2904W
Tamb = 25 ° C LM2904AW
Tmin ≤ Tamb ≤ Tmax LM2904W
Tmin ≤ Tamb ≤ Tmax LM2904AW
-I
DVio
Min.
E
Vio
Parameter
IV
E
Electrical characteristics
20
20
mV
LM2904W, LM2904AW
Table 3.
VCC+ = 5 V, VCC- = Ground, VO = 1.4 V, Tamb = 25 °C
(unless otherwise specified) (continued)
Parameter
Min.
Typ.
SR
Slew rate
VCC+ = 15 V, Vin = 0.5 to 3 V, RL = 2 kΩ, CL = 100 pF, unity gain
Tmin ≤ Tamb ≤ Tmax
0.3
0.2
0.6
GBP
Gain bandwidth product
f = 100 kHz, VCC+ = 30 V, Vin = 10 mV, RL = 2 kΩ, CL = 100pF
0.7
THD
Total harmonic distortion
f = 1 kHz, AV = 20 dB, RL = 2 kΩ, Vo = 2 Vpp, CL = 100 pF,
VCC+ = 30 V
NA
CT
1.1
Equivalent input noise voltage
f = 1 kHz, RS = 100 Ω, VCC+ = 30 V
120
VO = 1.4 V, RS = 0 Ω, 5 V < VCC+ < 30 V, 0 V < Vic < VCC+ - 1.5 V
V/µs
MHz
%
0.02
55
Channel separation (3)
1 kHz ≤ f ≤ 20 kHz
Unit
nV/√ Hz
dB
-I
VO1/VO2
Max.
IV
E
Symbol
en
1.
Electrical characteristics
E
2. The direction of the input current is out of the IC. This current is essentially constant, independent of the state of the output,
so there is no change in the loading charge on the input lines.
IN
AC
TI
VE
-I
NA
CT
IV
3. Due to the proximity of external components, ensure that stray capacitance does not cause coupling between these
external parts. Typically, this can be detected because this type of capacitance increases at higher frequencies.
Doc ID 9893 Rev 11
7/21
Electrical characteristics
Figure 2.
LM2904W, LM2904AW
Open loop frequency response
Figure 3.
Large signal frequency response
20
140
100k Ω
10MΩ
1k Ω
0.1μF
VI
VCC/2
+
80
VCC = 30V &
-55°C Tamb
60
+125°C
40
20
VCC = +10 to + 15V &
-55°C Tamb +125°C
15
10
5
0
10
100
1k
10k
100k
1M
10M
1k
Figure 5.
1M
Output voltage vs output sink
current
1
1
10
20
30
-I
0
NA
2
VCC = +5V
VCC = +15V
VCC = +30V
E
OUTPUT VOLTAGE (V)
IV
2
CT
OUTPUT
VOLTAGE (V)
3
3
INPUT
VOLTAGE (V)
100k
10
RL 2 kΩ
VCC = +15V
0
1
v cc
v cc /2
40
IO
VO
+
Tamb = +25°C
0,001
TIME (μs)
-
0.1
0.01
0,01
0,1
1
10
100
OUTPUT SINK CURRENT ( mA)
Figure 7.
TI
VE
Voltage follower pulse response
(Vcc = 30 V)
IN
AC
8/21
10k
-I
Voltage follower pulse response
(Vcc = 15 V)
4
Figure 6.
2k Ω
+
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 4.
VO
VI
+7V
0
1.0
+15V
-
IV
E
VOLTAGE GAIN (dB)
100
VO
NA
CT
VCC
-
OUTPUT SWING (Vpp)
120
Doc ID 9893 Rev 11
(Vcc+ - Vout) vs output source
current
Input current versus temperature
Figure 9.
Current limiting
Figure 11.
IV
E
n
Figure 8.
Electrical characteristics
NA
CT
LM2904W, LM2904AW
Supply current
Figure 13. Input current versus supply voltage
TI
VE
Figure 12. Voltage gain
-I
NA
CT
IV
E
-I
Figure 10. Input voltage range
160
120
R L = 2k Ω
80
IN
AC
VOLTAGE GAIN (dB)
R L = 20kΩ
40
0
10
20
30
40
POSITIVE SUPPLY VOLTAGE (V)
Doc ID 9893 Rev 11
9/21
Electrical characteristics
LM2904W, LM2904AW
Figure 15. Power supply rejection ratio
Figure 16. Common mode rejection ratio
Figure 17. Phase margin vs capacitive load
-I
NA
CT
IV
E
Figure 14. Gain bandwidth product
IN
AC
TI
VE
-I
NA
CT
IV
E
Phase Margin at Vcc=15V and Vicm=7.5V
Vs. Iout and Capacitive load value
10/21
Doc ID 9893 Rev 11
LM2904W, LM2904AW
Electrical characteristics
Typical single-supply applications
/0
H, a
9&&
5
N7
5
N7
5I
5
DV VKRZQ $9
5
N7
&,
$9
&
M)
933
HR
5/
N7
5
07
5
N7
-I
CT
N7
H
N7
H
N7
H
TI
VE
IN
AC
/0
,
H,
,%
5
N7
,I5 5DQG5 5 5 5
5
HR >@HH
5
$VVKRZQHR HH
N7
Figure 23. Using symmetrical amplifiers to
reduce input current
5
N7
/0
H2
HR HHHH
ZKHUHHH q HH
WRNHHSHR q 9
H , P9
Figure 22. High input Z, DC differential
amplifier
5
N7
/0
N7
-I
N7
E
NA
5
0 7
9
H 2 9
/0
H2
IV
$ 9 5
5
$V VKRZQ $ 9
N7
5
N7
Figure 21. DC summing amplifier
H
9
9
5/
N 7
9&&
&
M)
Figure 20. Non-inverting DC gain
5
N7
933
HR
5%
N7
H, a
&R
/0
&,
&
M)
5
N7
$ 9 5
5
DV VKRZQ $ 9
&R
5%
N7
5
N7
5
07
NA
CT
5I
N7
Figure 19. AC coupled non-inverting amplifier
IV
E
Figure 18. AC coupled inverting amplifier
,
HR
, % /0
1
M )
9R
,%
,%
07
07
Doc ID 9893 Rev 11
,%
/0
,QSXW FXUUHQW FRPSHQVDWLRQ
11/21
Electrical characteristics
LM2904W, LM2904AW
Figure 24. Low drift peak detector
Figure 25. Active bandpass filter
5
N7
,%
H,
&
M )
=,
1
,%
5
0 7
9
=R
,%
M )
5
07
5
N7
,%
5
07
&
S)
/0
/0
,QSXW FXUUHQW
FRPSHQVDWLRQ
)R N+]
4
$Y G%
E
IV
CT
NA
-I
TI
VE
IN
AC
12/21
Doc ID 9893 Rev 11
5
N7
/0
5
N7
5
N7
-I
,%
/0
5
N7
NA
CT
/0
&
S)
HR
IV
E
, % /0
9R
5
N7
9&&
&
M)
LM2904W, LM2904AW
Macromodel
4
Macromodel
4.1
Important note concerning this macromodel
IV
E
Please consider the following remarks before using these macromodels.
All models are a trade-off between accuracy and complexity (i.e. simulation time).
●
Macromodels are not a substitute to breadboarding; rather, they confirm the validity of
a design approach and help to select surrounding component values.
●
A macromodel emulates the nominal performance of a typical device within specified
operating conditions (for example, temperature, supply voltage). Thus the
macromodel is often not as exhaustive as the datasheet, its purpose is to illustrate the
main parameters of the product.
NA
CT
●
E
Macromodel code
TI
VE
-I
NA
CT
IV
** Standard Linear Ics Macromodels, 1993.
** ESD diodes added to the initial macromodel (2007).
** CONNECTIONS :
* 1 INVERTING INPUT
* 2 NON-INVERTING INPUT
* 3 OUTPUT
* 4 POSITIVE POWER SUPPLY
* 5 NEGATIVE POWER SUPPLY
.SUBCKT LM2904W 1 2 3 4 5
***************************
.MODEL MDTH D IS=1E-8 KF=3.104131E-15 CJO=10F
D1A 1 4 MDTH 400E-12
D1B 5 1 MDTH 400E-12
D2A 2 4 MDTH 400E-12
D2B 5 2 MDTH 400E-12
* INPUT STAGE
CIP 2 5 1.000000E-12
CIN 1 5 1.000000E-12
EIP 10 5 2 5 1
EIN 16 5 1 5 1
RIP 10 11 2.600000E+01
RIN 15 16 2.600000E+01
RIS 11 15 2.003862E+02
DIP 11 12 MDTH 400E-12
DIN 15 14 MDTH 400E-12
VOFP 12 13 DC 0
VOFN 13 14 DC 0
IPOL 13 5 1.000000E-05
CPS 11 15 3.783376E-09
DINN 17 13 MDTH 400E-12
VIN 17 5 0.000000e+00
IN
AC
4.2
-I
Data derived from macromodels used outside of the specified conditions (for example, VCC,
temperature) or even worse, outside of the device operating conditions (for example, VCC,
Vicm), are not reliable in any way.
Doc ID 9893 Rev 11
13/21
LM2904W, LM2904AW
NA
CT
-I
E
IN
AC
TI
VE
-I
NA
CT
IV
DINR 15 18 MDTH 400E-12
VIP 4 18 2.000000E+00
FCP 4 5 VOFP 3.400000E+01
FCN 5 4 VOFN 3.400000E+01
FIBP 2 5 VOFN 2.000000E-03
FIBN 5 1 VOFP 2.000000E-03
* AMPLIFYING STAGE
FIP 5 19 VOFP 3.600000E+02
FIN 5 19 VOFN 3.600000E+02
RG1 19 5 3.652997E+06
RG2 19 4 3.652997E+06
CC 19 5 6.000000E-09
DOPM 19 22 MDTH 400E-12
DONM 21 19 MDTH 400E-12
HOPM 22 28 VOUT 7.500000E+03
VIPM 28 4 1.500000E+02
HONM 21 27 VOUT 7.500000E+03
VINM 5 27 1.500000E+02
EOUT 26 23 19 5 1
VOUT 23 5 0
ROUT 26 3 20
COUT 3 5 1.000000E-12
DOP 19 25 MDTH 400E-12
VOP 4 25 2.242230E+00
DON 24 19 MDTH 400E-12
VON 24 5 7.922301E-01
.ENDS
IV
E
Macromodel
14/21
Doc ID 9893 Rev 11
LM2904W, LM2904AW
Package information
TI
VE
-I
NA
CT
IV
E
-I
NA
CT
IV
E
In order to meet environmental requirements, ST offers these devices in different grades of
ECOPACK® packages, depending on their level of environmental compliance. ECOPACK®
specifications, grade definitions and product status are available at: www.st.com.
ECOPACK® is an ST trademark.
IN
AC
5
Package information
Doc ID 9893 Rev 11
15/21
Package information
5.1
LM2904W, LM2904AW
DIP8 package information
DIP8 package mechanical data
Ref.
Inches
Max.
Min.
Typ.
5.33
Max.
0.210
A1
-I
Typ.
A2
2.92
3.30
4.95
0.115
0.130
0.195
b
0.36
0.46
0.56
0.014
0.018
0.022
b2
1.14
1.52
1.78
0.045
0.060
0.070
c
0.20
0.25
0.36
0.008
0.010
0.014
D
9.02
9.27
10.16
0.355
0.365
0.400
E
7.62
7.87
8.26
0.300
0.310
0.325
E1
6.10
6.35
7.11
0.240
0.250
0.280
IN
AC
TI
VE
0.38
0.015
e
2.54
0.100
eA
7.62
0.300
eB
L
16/21
Dimensions
Millimeters
Min.
A
NA
Table 4.
CT
IV
E
-I
NA
CT
IV
E
Figure 26. DIP8 package mechanical drawing
10.92
2.92
3.30
3.81
Doc ID 9893 Rev 11
0.430
0.115
0.130
0.150
LM2904W, LM2904AW
SO-8 package information
SO-8 package mechanical data
Ref.
A1
0.10
Inches
Max.
Min.
Typ.
1.75
0.25
1.25
TI
VE
A2
Typ.
-I
Min.
A
Dimensions
Millimeters
NA
Table 5.
CT
IV
E
-I
NA
CT
IV
E
Figure 27. SO-8 package mechanical drawing
Max.
0.069
0.004
0.010
0.049
b
0.28
0.48
0.011
0.019
c
0.17
0.23
0.007
0.010
D
4.80
4.90
5.00
0.189
0.193
0.197
E
5.80
6.00
6.20
0.228
0.236
0.244
E1
3.80
3.90
4.00
0.150
0.154
0.157
IN
AC
5.2
Package information
e
1.27
0.050
h
0.25
0.50
0.010
0.020
L
0.40
1.27
0.016
0.050
L1
k
ccc
1.04
1°
0.040
8°
0.10
Doc ID 9893 Rev 11
1°
8°
0.004
17/21
Package information
5.3
LM2904W, LM2904AW
TSSOP8 package information
CT
TSSOP8 package mechanical data
Ref.
Min.
0.80
1.00
Inches
Max.
Min.
Typ.
1.20
Max.
0.047
0.15
0.002
1.05
0.031
0.006
0.039
0.041
0.19
0.30
0.007
0.012
c
0.09
0.20
0.004
0.008
D
2.90
3.00
3.10
0.114
0.118
0.122
E
6.20
6.40
6.60
0.244
0.252
0.260
E1
4.30
4.40
4.50
0.169
0.173
0.177
IN
AC
b
e
0.65
k
0°
L
0.45
L1
aaa
18/21
Typ.
0.05
TI
VE
A2
-I
A
A1
Dimensions
Millimeters
NA
Table 6.
IV
E
-I
NA
CT
IV
E
Figure 28. TSSOP8 package mechanical drawing
0.60
0.0256
8°
0°
0.75
0.018
1.00
8°
0.024
0.030
0.039
0.10
Doc ID 9893 Rev 11
0.004
LM2904W, LM2904AW
Ordering information
6
Ordering information
Table 7.
Order codes
Temperature
range
LM2904WN
DIP8
LM2904WD
LM2904WDT
SO-8
LM2904WPT
-40°C, +125°C
LM2904WYDT(1)
LM2904WYPT(2)
LM2904AWYPT
Packing
IV
E
Package
TSSOP8
Marking
Tube
LM2904W
Tube or
tape & reel
2904W
NA
CT
Order code
Tape & reel
2904W
SO-8
(automotive grade level)
Tube or
tape & reel
2904WY
TSSOP8
(automotive grade level)
Tape & reel
K04WY
K05WY
-I
1. Qualified and characterized according to AEC Q100 and Q003 or equivalent, advanced screening according to AEC Q001
& Q 002 or equivalent.
IN
AC
TI
VE
-I
NA
CT
IV
E
2. Qualification and characterization according to AEC Q100 and Q003 or equivalent, advanced screening according to AEC
Q001 & Q 002 or equivalent are on-going.
Doc ID 9893 Rev 11
19/21
Revision history
LM2904W, LM2904AW
7
Revision history
Table 8.
Document revision history
Revision
Changes
1-Sep-2003
1
Initial release.
1-Jul-2005
2
PPAP references inserted in the datasheet see Section 6: Ordering information
on page 19.
ESD protection inserted in Table 1: Absolute maximum ratings (AMR) on
page 4.
1-Oct-2005
3
Correction of error in AVD min. value see Table 3 on page 6.
1-Dec-2005
4
LM2904WYPT PPAP reference added in Section 6: Ordering information on
page 19.
Information added in Table 1: Absolute maximum ratings (AMR) on page 4.
2-May-2006
5
Minimum value of slew rate at 25°C and in temperature added in Table 3 on
page 6.
20-Jul-2007
6
Power dissipation value corrected in Table 1: Absolute maximum ratings
(AMR).
ESD tolerance for HBM model improved to 2kV in Table 3 on page 6.
Equivalent input noise voltage parameter added in Table 3.
Electrical characteristics curves updated.
Added Figure 17: Phase margin vs capacitive load on page 10.
Section 5: Package information updated.
Section 4: Macromodel added.
18-Dec-2007
7
Reformatted electrical characteristics table, Table 3.
Deleted Vopp parameter in Table 3.
Corrected footnotes for automotive grade order codes in Table 7.
21-Feb-2008
8
Corrected SO-8 package mechanical data. Dimension E in drawing was
marked H in table.
Corrected revision history.
24-Feb-2011
9
IN
AC
12-Feb-2013
20/21
-I
Corrected x-axis in Figure 5.
TI
VE
04-Jul-2012
NA
CT
IV
E
-I
NA
CT
IV
E
Date
10
Removed commercial type LM2904WYD.
Updated Table 7: Order codes.
11
Added part number LM2904AW.
Added “automotive qualification to Features.
Table 3: VCC+ = 5 V, VCC- = Ground, VO = 1.4 V, Tamb = 25 °C (unless
otherwise specified): Updated Vio
Added order code LM2904AWYPT to Table 7: Order codes
Doc ID 9893 Rev 11
Please Read Carefully:
NA
CT
IV
E
LM2904W, LM2904AW
-I
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
E
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
CT
IV
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
NA
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
-I
UNLESS EXPRESSLY APPROVED IN WRITING BY TWO AUTHORIZED ST REPRESENTATIVES, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
TI
VE
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
IN
AC
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2013 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
Doc ID 9893 Rev 11
21/21