LM2904W

LM2904W Low power dual operational amplifier Features ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Internally frequency compensated Large DC voltage gain: 100 dB Wide bandwidth (unity gain): 1.1 MHz (temperature compensated) Very low supply current/op (500 µA) Low input bias current: 20 nA (temperature compensated) Low input offset current: 2 nA Input common-mode voltage range includes negative rail Differential input voltage range equal to the power supply voltage Large output voltage swing 0V to (VCC+ - 1.5 V) ESD internal protection: 2 kV P TSSOP8 (Thin shrink small outline package) D SO-8 (Plastic micropackage) N DIP8 (Plastic package) Description This circuit consists of two independent, high gain, internally frequency compensated operational amplifiers, designed specifically for automotive and industrial control system. It operates from a single power supply over a wide range of voltages. The low power supply drain is independent of the magnitude of the power supply voltage. Application areas include transducer amplifiers, DC gain blocks and all the conventional op-amp circuits which now can be more easily implemented in single power supply systems. For example, these circuits can be directly supplied from standard +5 V which is used in logic systems and will easily provide the required interface electronics without requiring any additional power supply. In linear mode the input common-mode voltage range includes ground and the output voltage can also swing to ground, even though operated from a single power supply. Pin connections (top view) February 2008 Rev 8 1/19 www.st.com 19 Schematic diagram LM2904W 1 Schematic diagram Figure 1. Schematic diagram (1/2 LM2904W) 2/19 LM2904W Absolute maximum ratings and operating conditions 2 Table 1. Symbol VCC Vid Vin Absolute maximum ratings and operating conditions Absolute maximum ratings (AMR) Parameter Supply voltage (1) Differential input voltage Input voltage Output short-circuit duration(3) Iin Tstg Tj Input current (4) (2) Value +32 -0.3V to VCC + 0.3 -0.3V to VCC + 0.3 Infinite 50 -65 to +150 150 125 120 85 40 37 41 -65 to +150 2000 200 1500 Unit V V V s mA °C °C Storage temperature range Maximum junction temperature Thermal resistance junction to ambient(5) SO-8 TSSOP8 DIP8 Thermal resistance junction to case(5) SO-8 TSSOP8 DIP8 Storage temperature range HBM: human body MM: machine model(7) CDM: charged device model(8) model(6) Rthja °C/W Rthjc °C/W Tstg ESD °C V 1. All voltage values, except differential voltage are with respect to network ground terminal. 2. Differential voltages are the non-inverting input terminal with respect to the inverting input terminal. 3. Short-circuits from the output to VCC can cause excessive heating if VCC+ > 15 V. The maximum output current is approximately 40 mA, independent of the magnitude of VCC. Destructive dissipation can result from simultaneous shortcircuits on all amplifiers. 4. This input current only exists when the voltage at any of the input leads is driven negative. It is due to the collector-base junction of the input PNP transistor becoming forward biased and thereby acting as input diode clamps. In addition to this diode action, there is also NPN parasitic action on the IC chip. This transistor action can cause the output voltages of the Op-amps to go to the VCC voltage level (or to ground for a large overdrive) for the time during which an input is driven negative. This is not destructive and normal output is restored for input voltages above -0.3 V. 5. Short-circuits can cause excessive heating and destructive dissipation. Rth are typical values. 6. Human body model: 100 pF discharged through a 1.5 kΩ resistor between two pins of the device, done for all couples of pin combinations with other pins floating. 7. Machine model: a 200 pF cap is charged to the specified voltage, then discharged directly between two pins of the device with no external series resistor (internal resistor < 5 Ω), done for all couples of pin combinations with other pins floating. 8. Charged device model: all pins plus package are charged together to the specified voltage and then discharged directly to the ground. Table 2. Symbol VCC Vicm Toper Operating conditions Parameter Supply voltage Common mode input voltage range Tmin ≤ Tamb ≤ Tmax Operating free-air temperature range Value 3 to 30 VCC+ - 1.5 VCC+ - 2 -40 to +125 Unit V V °C 3/19 Electrical characteristics LM2904W 3 Table 3. Symbol Vio DVio Iio DIio Iib Electrical characteristics VCC+ = 5V, VCC- = Ground, VO = 1.4V, Tamb = 25°C (unless otherwise specified) Parameter Input offset voltage (1) Tmin ≤ Tamb ≤ Tmax Input offset voltage drift Input offset current Tmin ≤ Tamb ≤ Tmax Input offset current drift Input bias current Tmin ≤ Tamb ≤ Tmax Large signal voltage gain , VCC+= +15V, RL=2kΩ Vo=1.4V to 11.4V Tmin ≤ Tamb ≤ Tmax Supply voltage rejection ratio RS ≤10kΩ Tmin ≤ Tamb ≤ Tmax Supply current, all Amp, no load VCC = +5V Tmin ≤ Tamb ≤ Tmax, VCC = +30V Common-mode rejection ratio RS = 10kΩ Tmin ≤ Tamb ≤ Tmax Output short-circuit current VCC+ = +15V, Vo = +2V, Vid = +1V Output sink current VO = 2V, VCC+ = +5V VO = +0.2V, VCC+ = +15V High level output voltage VCC+ = + 30V RL = 2kΩ Tmin ≤ Tamb ≤ Tmax RL = 10kΩ Tmin ≤ Tamb ≤ Tmax Low level output voltage RL = 10kΩ Tmin ≤ Tamb ≤ Tmax Slew rate VCC+ = 15V, Vin = 0.5 to 3V, RL = 2kΩ CL = 100pF, unity gain , Tmin ≤ Tamb ≤ Tmax 0.3 0.2 70 60 20 50 25 (2) Min. Typ. 2 7 2 10 20 Max. 7 9 30 30 40 300 150 200 Unit mV µV/°C nA pA/°C nA Avd 100 V/mV SVR 65 65 100 dB ICC 0.7 1.2 2 mA CMR 85 dB Isource 40 60 mA Isink 10 12 20 50 mA µA VOH 26 26 27 27 27 28 5 20 20 V VOL mV SR 0.6 V/µs 4/19 LM2904W Table 3. Symbol GBP Electrical characteristics VCC+ = 5V, VCC- = Ground, VO = 1.4V, Tamb = 25°C (unless otherwise specified) Parameter Gain bandwidth product , f = 100kHz, VCC+ = 30V, Vin = 10mV, RL = 2kΩ CL = 100pF Total harmonic distortion , f = 1kHz, AV = 20dB, RL = 2kΩ Vo = 2Vpp, CL = 100pF, VCC+ = 30V Equivalent input noise voltage , f = 1kHz, RS = 100Ω VCC+ = 30V Channel separation (3) 1kHz ≤ f ≤ 20kHz Min. 0.7 Typ. 1.1 Max. Unit MHz THD 0.02 % en VO1/VO2 1. 55 120 nV/√ Hz dB VO = 1.4 V, RS = 0 Ω, 5 V < VCC+ < 30 V, 0 V < Vic < VCC+ - 1.5 V 2. The direction of the input current is out of the IC. This current is essentially constant, independent of the state of the output, so there is no change in the loading charge on the input lines. 3. Due to the proximity of external components, ensure that stray capacitance does not cause coupling between these external parts. Typically, this can be detected because this type of capacitance increases at higher frequencies. 5/19 Electrical characteristics LM2904W Figure 2. 140 Open loop frequency response 10MΩ 0.1μF Figure 3. 20 Large signal frequency response 100k Ω 1k Ω +15V VO +7V + 2k Ω 120 VOLTAGE GAIN (dB) 100 80 60 40 20 0 1.0 10 100 VI VCC/2 + VO OUTPUT SWING (Vpp) - VCC 15 VI VCC = 30V & -55°C Tamb +125°C 10 5 VCC = +10 to + 15V & -55°C Tamb +125°C 1k 10k 100k 1M 10M 0 1k 10k 100k 1M FREQUENCY (Hz) FREQUENCY (Hz) Figure 4. 4 Voltage follower pulse response RL 2 kΩ VCC = +15V Figure 5. Output characteristics 10 VCC = +5V VCC = +15V VCC = +30V 1 v cc v cc /2 IO + VO OUTPUT VOLTAGE (V) 3 2 1 0 3 OUTPUT VOLTAGE (V) 0.1 INPUT VOLTAGE (V) 2 1 0.01 0 10 20 30 40 0,001 0,01 0,1 Tamb = +25°C 1 10 100 TIME (μ s) OUTPUT SINK CURRENT (μ A) Figure 6. 500 OUTPUT VOLTAGE REFERENCED Voltage follower pulse response ( ) + eO el 50pF Figure 7. Output characteristics 8 7 6 V CC /2 + IO VO V CC OUTPUT VOLTAGE (mV) 450 400 TO VCC+ (V) 5 4 3 2 1 0,001 0,01 Input 350 Output 300 250 0 1 2 3 4 - Independent of V CC T amb = +25°C Tamb = +25°C VCC = 30 V 5 6 7 8 0,1 1 10 100 TIME (ms) OUTPUT SOURCE CURRENT (mA) 6/19 LM2904W Electrical characteristics Figure 8. 90 80 Input current versus temperature VI = 0 V VCC = +30 V VCC = +15 V Figure 9. 90 Current limiting 80 70 60 50 40 30 20 10 0 + - OUTPUT CURRENT (mA) INPUT CURRENT (mA) IO 70 60 50 40 30 20 10 0 -55 -35 -15 VCC = +5 V 5 25 45 65 85 105 125 -55 -35 -15 5 25 45 65 85 105 125 TEMPERATURE (°C) TEMPERATURE (°C) Figure 10. Input voltage range 15 Figure 11. Supply current 4 VCC SUPPLY CURRENT (mA) INPUT VOLTAGE (V) 3 mA - ID 10 Négative 2 + 5 Positive 1 Tamb = 0°C to +125°C Tamb = -55°C 0 5 10 15 0 10 20 30 POWER SUPPLY VOLTAGE (±V) POSITIVE SUPPLY VOLTAGE (V) Figure 12. Voltage gain 160 Figure 13. Input current versus supply voltage 100 INPUT CURRENT (nA) R L = 20kΩ VOLTAGE GAIN (dB) 120 R L = 2k Ω 75 50 25 80 40 Tamb= +25°C 0 10 20 30 40 POSITIVE SUPPLY VOLTAGE (V) 0 10 20 30 POSITIVE SUPPLY VOLTAGE (V) 7/19 Electrical characteristics LM2904W Figure 14. Gain bandwidth product GAIN BANDWIDTH PRODUCT (MHz) 1.5 1.35 1.2 1.05 0.9 0.75 0.6 0.45 0.3 0.15 0 -55-35-15 5 25 45 65 85 105 125 TEMPERATURE (°C) VCC = 15V Figure 15. Power supply rejection ratio POWER SUPPLY REJECTION RATIO (dB) 115 110 SVR 105 100 95 90 85 80 75 70 65 60-55-35-15 5 25 45 65 85 105 125 TEMPERATURE (°C) Figure 16. Common mode rejection ratio COMMON MODE REJECTION RATIO (dB) Figure 17. Phase margin vs capacitive load Phase Margin at Vcc=15V and Vicm=7.5V Vs. Iout and Capacitive load value 115 110 105 100 95 90 85 80 75 70 65 60-55-35-15 5 25 45 65 85 105 125 TEMPERATURE (°C) 8/19 LM2904W Electrical characteristics Typical single-supply applications Figure 18. AC coupled inverting amplifier Rf 100k Ω R1 10k Ω 1/2 LM2904 Figure 19. AC coupled non-inverting amplifier R1 100k Ω C1 0.1μF R2 1M Ω A V= 1 + R2 R1 (as shown A V = 11) Co 0 eo RL 10k Ω 2VPP CI R1 (as shown AV = -10) Co 0 eo RL 10k Ω 2VPP AV = - Rf CI 1/2 LM2904 eI ~ R2 VCC 100k Ω RB 6.2kΩ R3 100k Ω RB 6.2k Ω eI ~ R3 1MΩ R4 100k Ω C1 10 μF VCC C2 10μF R5 100kΩ Figure 20. Non-inverting DC gain A V = 1 + R2 R1 (As shown A V = 101) Figure 21. DC summing amplifier e1 100kΩ 10kΩ 1/2 LM2904 eO +5V e2 e3 100kΩ 100kΩ 100kΩ 1/2 LM2904 eO R1 10k Ω R2 1M Ω (V) 100kΩ e4 100kΩ eo = e1 + e2 - e3 - e4 where (e1 + e2) ≥ (e3 + e4) to keep eo ≥ 0V e 0 O e I (mV) Figure 22. High input Z, DC differential amplifier Figure 23. Using symmetrical amplifiers to reduce input current 1/2 R2 100k Ω R1 100k Ω 1/2 LM2904 R4 100k Ω R3 100k Ω 1/2 LM2904 I eI IB I I B LM2904 2N 929 0.001μ F eo +V1 +V2 If R1 = R5 and R3 = R4 = R6 = R7 eo = [ 1 + 2R1 ] (e2 - e1) R2 As shown eo = 101 (e2 - e1) Vo IB IB 3M Ω IB 1/2 LM2904 Input current compensation 1.5M Ω 9/19 Electrical characteristics LM2904W Figure 24. Low drift peak detector IB 1/2 I B LM2904 Figure 25. Active bandpass filter R1 100k Ω C1 330pF eo Zo +V1 1/2 LM2904 R2 100k Ω 1/2 LM2904 R5 470k Ω 1/2 LM2904 eI ZI μ 1F C 2IB 2N 929 R4 10M Ω C2 330pF 1/2 LM2904 0.001μ F IB 3R 3M Ω IB 1/2 LM2904 R3 100k Ω R6 470k Ω Vo R7 100k Ω VCC R8 100k Ω C3 10 μF 2IB R 1M Ω Input current compensation Fo = 1kHz Q = 50 Av = 100 (40dB) 10/19 LM2904W Macromodel 4 4.1 Macromodel Important note concerning this macromodel Please consider the following remarks before using this macromodel. ● ● ● All models are a trade-off between accuracy and complexity (i.e. simulation time). Macromodels are not a substitute to breadboarding; rather, they confirm the validity of a design approach and help to select surrounding component values. A macromodel emulates the nominal performance of a typical device within specified operating conditions (temperature, supply voltage, for example). Thus the macromodel is often not as exhaustive as the datasheet, its purpose is to illustrate the main parameters of the product. Data derived from macromodels used outside of the specified conditions (VCC, temperature, for example) or even worse, outside of the device operating conditions (VCC, Vicm, for example), is not reliable in any way. 4.2 Macromodel code ** Standard Linear Ics Macromodels, 1993. ** ESD diodes added to the initial macromodel (2007). ** CONNECTIONS : * 1 INVERTING INPUT * 2 NON-INVERTING INPUT * 3 OUTPUT * 4 POSITIVE POWER SUPPLY * 5 NEGATIVE POWER SUPPLY .SUBCKT LM2904W 1 2 3 4 5 *************************** .MODEL MDTH D IS=1E-8 KF=3.104131E-15 CJO=10F D1A 1 4 MDTH 400E-12 D1B 5 1 MDTH 400E-12 D2A 2 4 MDTH 400E-12 D2B 5 2 MDTH 400E-12 * INPUT STAGE CIP 2 5 1.000000E-12 CIN 1 5 1.000000E-12 EIP 10 5 2 5 1 EIN 16 5 1 5 1 RIP 10 11 2.600000E+01 RIN 15 16 2.600000E+01 RIS 11 15 2.003862E+02 DIP 11 12 MDTH 400E-12 DIN 15 14 MDTH 400E-12 VOFP 12 13 DC 0 VOFN 13 14 DC 0 IPOL 13 5 1.000000E-05 CPS 11 15 3.783376E-09 DINN 17 13 MDTH 400E-12 VIN 17 5 0.000000e+00 11/19 Macromodel DINR 15 18 MDTH 400E-12 VIP 4 18 2.000000E+00 FCP 4 5 VOFP 3.400000E+01 FCN 5 4 VOFN 3.400000E+01 FIBP 2 5 VOFN 2.000000E-03 FIBN 5 1 VOFP 2.000000E-03 * AMPLIFYING STAGE FIP 5 19 VOFP 3.600000E+02 FIN 5 19 VOFN 3.600000E+02 RG1 19 5 3.652997E+06 RG2 19 4 3.652997E+06 CC 19 5 6.000000E-09 DOPM 19 22 MDTH 400E-12 DONM 21 19 MDTH 400E-12 HOPM 22 28 VOUT 7.500000E+03 VIPM 28 4 1.500000E+02 HONM 21 27 VOUT 7.500000E+03 VINM 5 27 1.500000E+02 EOUT 26 23 19 5 1 VOUT 23 5 0 ROUT 26 3 20 COUT 3 5 1.000000E-12 DOP 19 25 MDTH 400E-12 VOP 4 25 2.242230E+00 DON 24 19 MDTH 400E-12 VON 24 5 7.922301E-01 .ENDS LM2904W 12/19 LM2904W Package information 5 Package information In order to meet environmental requirements, ST offers these devices in ECOPACK® packages. These packages have a lead-free second level interconnect. The category of second level interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an ST trademark. ECOPACK specifications are available at: www.st.com. 13/19 Package information LM2904W 5.1 SO-8 package information Figure 26. SO-8 package mechanical drawing Table 4. SO-8 package mechanical data Dimensions Ref. Min. A A1 A2 b c D E E1 e h L k ccc 0.25 0.40 1° 0.10 1.25 0.28 0.17 4.80 5.80 3.80 Millimeters Typ. Max. 1.75 0.25 0.004 0.049 0.48 0.23 4.90 6.00 3.90 1.27 0.50 1.27 8° 0.10 0.010 0.016 1° 5.00 6.20 4.00 0.011 0.007 0.189 0.228 0.150 Min. Inches Typ. Max. 0.069 0.010 0.019 0.010 0.193 0.236 0.154 0.050 0.020 0.050 8° 0.004 0.197 0.244 0.157 14/19 LM2904W Package information 5.2 DIP8 package information Figure 27. DIP8 package mechanical drawing Table 5. DIP8 package mechanical data Dimensions Ref. Min. A A1 A2 b b2 c D E E1 e eA eB L 2.92 0.38 2.92 0.36 1.14 0.20 9.02 7.62 6.10 Millimeters Typ. Max. 5.33 0.015 3.30 0.46 1.52 0.25 9.27 7.87 6.35 2.54 7.62 10.92 3.30 3.81 0.115 4.95 0.56 1.78 0.36 10.16 8.26 7.11 0.115 0.014 0.045 0.008 0.355 0.300 0.240 Min. Inches Typ. Max. 0.210 0.130 0.018 0.060 0.010 0.365 0.310 0.250 0.100 0.300 0.195 0.022 0.070 0.014 0.400 0.325 0.280 0.430 0.130 0.150 15/19 Package information LM2904W 5.3 TSSOP8 package information Figure 28. TSSOP8 package mechanical drawing Table 6. TSSOP8 package mechanical data Dimensions Ref. Min. A A1 A2 b c D E E1 e k L L1 aaa 0° 0.45 0.05 0.80 0.19 0.09 2.90 6.20 4.30 Millimeters Typ. Max. 1.2 0.15 1.00 1.05 0.30 0.20 3.00 6.40 4.40 0.65 8° 0.60 1 0.1 0.75 0° 0.018 3.10 6.60 4.50 0.002 0.031 0.007 0.004 0.114 0.244 0.169 Min. Inches Typ. Max. 0.047 0.006 0.039 0.041 0.012 0.008 0.118 0.252 0.173 0.0256 8° 0.024 0.039 0.004 0.030 0.122 0.260 0.177 16/19 LM2904W Ordering information 6 Table 7. Ordering information Order codes Temperature range Package DIP8 SO-8 -40°C, +125°C TSSOP8 SO-8 (Automotive grade level) TSSOP8 (Automotive grade level) Packing Tube Tube or tape & reel Tape & reel Tube or tape & reel Tape & reel Marking LM2904W 2904W 2904W 2904WY K04WY Order code LM2904WN LM2904WD LM2904WDT LM2904WPT LM2904WYD(1) LM2904WYDT(1) LM2904WYPT(2) 1. Qualified and characterized according to AEC Q100 and Q003 or equivalent, advanced screening according to AEC Q001 & Q 002 or equivalent. 2. Qualification and characterization according to AEC Q100 and Q003 or equivalent, advanced screening according to AEC Q001 & Q 002 or equivalent are on-going. 17/19 Revision history LM2904W 7 Table 8. Date Revision history Document revision history Revision 1 Initial release. PPAP references inserted in the datasheet see Section 6: Ordering information on page 17. ESD protection inserted in Table 1: Absolute maximum ratings (AMR) on page 3. Correction of error in AVD min. value see Table 3 on page 4. LM2904WYPT PPAP reference added in Section 6: Ordering information on page 17. Information added in Table 1: Absolute maximum ratings (AMR) on page 3. Minimum value of slew rate at 25°C and in temperature added in Table 3 on page 4. Power dissipation value corrected in Table 1: Absolute maximum ratings (AMR). ESD tolerance for HBM model improved to 2kV in Table 3 on page 4. Equivalent input noise voltage parameter added in Table 3. Electrical characteristics curves updated. Added Figure 17: Phase margin vs capacitive load on page 8. Section 5: Package information updated. Section 4: Macromodel added. Reformatted electrical characteristics table, Table 3. Deleted Vopp parameter in Table 3. Corrected footnotes for automotive grade order codes in Table 7. Corrected SO-8 package mechanical data. Dimension E in drawing was marked H in table. Corrected revision history. Changes 1-Sep-2003 1-Jul-2005 2 1-Oct-2005 1-Dec-2005 3 4 2-May-2006 5 20-Jul-2007 6 18-Dec-2007 7 21-Feb-2008 8 18/19 LM2904W Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2008 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 19/19