M27W201_06

M27W201 2 Mbit (256Kb x 8) Low Voltage UV EPROM and OTP EPROM Features ■ ■ 2.7V to 3.6V Low Voltage in Read Operation Access Time: – 70 ns at VCC = 3.0V to 3.6V – 80 ns at VCC = 2.7V to 3.6V Pin Compatible with M27C2001 Low Power Consumption: – 15 µA Max. Standby Current – 15 mA Max. Active Current at 5 MHz Programming Time: 100 µs/byte High Reliability CMOS Technology – 2,000V ESD Protection – 200 mA Latch-up Protection Immunity Electronic Signature – Manufacturer Code: 20h – Device Code: 61h ECOPACK® packages available TSOP32 (NZ) 8 x 14 mm 1 32 32 ■ ■ 1 FDIP32W (F) PDIP32 (B) ■ ■ PLCC32 (C) ■ TSOP32 (N) 8 x 20 mm ■ April 2006 Rev 4 1/24 www.st.com 1 Contents M27W201 Contents 1 2 Summary description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Device Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 2.10 Read mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Standby mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Two-line output control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 System considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Presto II programming algorithm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Program Inhibit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Program Verify . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Electronic Signature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Erasure operation (applies to UV EPROM) . . . . . . . . . . . . . . . . . . . . . . . 11 3 4 5 Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 DC and AC parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 5.1 5.2 5.3 5.4 5.5 32-pin Ceramic Frit-seal DIP, with round window (FDIP32WA) . . . . . . . . 17 32-pin Plastic DIP, 600 mils width (PDIP32) . . . . . . . . . . . . . . . . . . . . . . . 18 32-lead Rectangular Plastic Leaded Chip Carrier (PLCC32) . . . . . . . . . . 19 32-lead Plastic Thin Small Outline, 8 x 20 mm (TSOP32) . . . . . . . . . . . . 20 32-lead Plastic Thin Small Outline, 8x 14 mm (TSOP32) . . . . . . . . . . . . 21 6 7 Part numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 2/24 M27W201 List of tables List of tables Table 1. Table 2. Table 3. Table 4. Table 5. Table 6. Table 7. Table 8. Table 9. Table 10. Table 11. Table 12. Table 13. Table 14. Table 15. Table 16. Table 17. Signal Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Operating modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Electronic Signature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Read Mode DC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Programming Mode DC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 AC Measurement Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Capacitance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Read Mode AC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Programming Mode AC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 FDIP32WA package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 PDIP32 package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 PLCC32 package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 TSOP32 package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 TSOP32 package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Ordering Information Scheme. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 3/24 List of figures M27W201 List of figures Figure 1. Figure 2. Figure 3. Figure 4. Figure 5. Figure 6. Figure 7. Figure 8. Figure 9. Figure 10. Figure 11. Figure 12. Figure 13. Figure 14. Logic Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 DIP Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 LCC Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 TSOP Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Programming flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 AC Testing Input Output Waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 AC Testing Load Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Read Mode AC Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Programming and Verify Modes AC Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 FDIP32WA package outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 PDIP32 package outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 PLCC32 package outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 TSOP32 package outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 TSOP32 package outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 4/24 M27W201 Summary description 1 Summary description The M27W201 is a low voltage 2 Mbit EPROM offered in the two range UV (ultra violet erase) and OTP (one time programmable). It is ideally suited for microprocessor systems requiring large data or program storage and is organised as 262,144 by 8 bits. The M27W201 operates in the read mode with a supply voltage as low as 2.7V at –40 to 85°C temperature range. The decrease in operating power allows either a reduction of the size of the battery or an increase in the time between battery recharges. The FDIP32W (window ceramic frit-seal package) has a transparent lid which allows the user to expose the chip to ultraviolet light to erase the bit pattern. A new pattern can then be written to the device by following the programming procedure. For application where the content is programmed only one time and erasure is not required, the M27W201 is offered in PDIP32, PLCC32 and TSOP32 (8 x 20mm and 8 x 14mm) packages. In order to meet environmental requirements, ST offers the M27W201 in ECOPACK® packages. ECOPACK packages are Lead-free. The category of second Level Interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an ST trademark. ECOPACK® specifications are available at: www.st.com. See Figure 1: Logic Diagram and Table 1: Signal Descriptions for a brief overview of the signals connected to this device. Figure 1. Logic Diagram VCC VPP 18 A0-A17 8 Q0-Q7 P E G M27W201 VSS AI01359 5/24 Summary description Table 1. Signal Descriptions Signal A0-A17 Q0-Q7 E G P VPP VCC VSS Address Inputs Data Outputs Chip Enable Output Enable Program Program Supply Supply Voltage Ground Description M27W201 Figure 2. DIP Connections VPP A16 A15 A12 A7 A6 A5 A4 A3 A2 A1 A0 Q0 Q1 Q2 VSS 1 32 2 31 3 30 4 29 5 28 6 27 7 26 8 25 M27W201 9 24 10 23 11 22 12 21 13 20 14 19 15 18 16 17 AI02675 VCC P A17 A14 A13 A8 A9 A11 G A10 E Q7 Q6 Q5 Q4 Q3 6/24 M27W201 Figure 3. LCC Connections A12 A15 A16 VPP VCC P A17 Summary description 1 32 A7 A6 A5 A4 A3 A2 A1 A0 Q0 A14 A13 A8 A9 A11 G A10 E Q7 9 M27W201 25 17 Q1 Q2 VSS Q3 Q4 Q5 Q6 AI01360 Figure 4. TSOP Connections A11 A9 A8 A13 A14 A17 P VCC VPP A16 A15 A12 A7 A6 A5 A4 1 32 G A10 E Q7 Q6 Q5 Q4 Q3 VSS Q2 Q1 Q0 A0 A1 A2 A3 8 9 M27W201 25 24 16 17 AI01361 7/24 Device Description M27W201 2 Device Description The operating modes of the M27W201 are listed in the Operating Modes table. A single power supply is required in the read mode. All inputs are TTL levels except for VPP and 12V on A9 for Electronic Signature. Table 1. Operating Modes Table 2. Operating modes Mode E VIL VIL VIL VIL VIH VIH VIL G VIL VIH VIH VIL X X VIL P X X VIL Pulse VIH X X VIH A9 X X X X X X VID VPP VCC or VSS VCC or VSS VPP VPP VPP VCC or VSS VCC Q7-Q0 Data Out Hi-Z Data In Data Out Hi-Z Hi-Z Codes Read Output Disable Program Verify Program Inhibit Standby Electronic Signature Note: X = VIH or VIL, VID = 12V ± 0.5V. 2.1 Read mode The M27W201 has two control functions, both of which must be logically active in order to obtain data at the outputs. Chip Enable (E) is the power control and should be used for device selection. Output Enable (G) is the output control and should be used to gate data to the output pins, independent of device selection. Assuming that the addresses are stable, the address access time (tAVQV) is equal to the delay from E to output (tELQV). Data is available at the output after a delay of tGLQV from the falling edge of G, assuming that E has been low and the addresses have been stable for at least tAVQV-tGLQV. 2.2 Standby mode The M27W201 has a standby mode which reduces the supply current from 15mA to 15µA with low voltage operation VCC ≤ 3.6V, see Read Mode DC Characteristics table for details.The M27W201 is placed in the standby mode by applying a CMOS high signal to the E input. When in the standby mode, the outputs are in a high impedance state, independent of the G input. 8/24 M27W201 Device Description 2.3 Two-line output control Because EPROMs are usually used in larger memory arrays, this product features a 2-line control function which accommodates the use of multiple memory connection. The two line control function allows: ● ● the lowest possible memory power dissipation, complete assurance that output bus contention will not occur. For the most efficient use of these two control lines, E should be decoded and used as the primary device selecting function, while G should be made a common connection to all devices in the array and connected to the READ line from the system control bus. This ensures that all deselected memory devices are in their low power standby mode and that the output pins are only active when data is required from a particular memory device. 2.4 System considerations The power switching characteristics of Advanced CMOS EPROMs require careful decoupling of the devices. The supply current, ICC, has three segments that are of interest to the system designer: the standby current level, the active current level, and transient current peaks that are produced by the falling and rising edges of E. The magnitude of the transient current peaks is dependent on the capacitive and inductive loading of the device at the output. The associated transient voltage peaks can be suppressed by complying with the two line output control and by properly selected decoupling capacitors. It is recommended that a 0.1µF ceramic capacitor be used on every device between VCC and VSS. This should be a high frequency capacitor of low inherent inductance and should be placed as close to the device as possible. In addition, a 4.7µF bulk electrolytic capacitor should be used between VCC and VSS for every eight devices. The bulk capacitor should be located near the power supply connection point. The purpose of the bulk capacitor is to overcome the voltage drop caused by the inductive effects of PCB traces. 2.5 Programming The M27W201 has been designed to be fully compatible with the M27C2001 and has the same electronic signature. As a result the M27W201 can be programmed as the M27C2001 on the same programming equipment applying 12.75V on VPP and 6.25V on VCC by the use of the same PRESTO II algorithm. When delivered (and after each ‘1’s erasure for UV EPROM), all bits of the M27W201 are in the '1' state.Data is introduced by selectively programming '0's into the desired bit locations. Although only '0's will be programmed, both '1's and '0's can be present in the data word. The only way to change a ‘0’ to a ‘1’ is by die exposure to ultraviolet light (UV EPROM). The M27W201 is in the programming mode when VPP input is at 12.75V, E is at VIL and P is pulsed to VIL. The data to be programmed is applied to 8 bits in parallel to the data output pins. The levels required for the address and data inputs are TTL. VCC is specified to be 6.25V ± 0.25V. 9/24 Device Description M27W201 2.6 Presto II programming algorithm Presto II Programming Algorithm allows the whole array to be programmed with a guaranteed margin, in a typical time of 26.5 seconds. Programming with Presto II consists of applying a sequence of 100µs program pulses to each byte until a correct verify occurs (see Figure 5). During programming and verify operation, a Margin mode circuit is automatically activated in order to guarantee that each cell is programmed with enough margin. No overprogram pulse is applied since the verify in Margin mode at VCC much higher than 3.6V, provides the necessary margin to each programmed cell. Figure 5. Programming flowchart VCC = 6.25V, VPP = 12.75V n=0 P = 100µs Pulse NO ++n = 25 YES NO VERIFY YES Last Addr NO ++ Addr FAIL YES CHECK ALL BYTES 1st: VCC = 5V 2nd: VCC = 2.7V AI00715D 2.7 Program Inhibit Programming of multiple M27W201s in parallel with different data is also easily accomplished. Except for E, all like inputs including G of the parallel M27W201 may be common. A TTL low level pulse applied to a M27W201's P input, with E low and VPP at 12.75V, will program that M27W201. A high level E input inhibits the other M27W201s from being programmed. 2.8 Program Verify A verify (read) should be performed on the programmed bits to determine that they were correctly programmed. The verify is accomplished with E and G at VIL, P at VIH, VPP at 12.75V and VCC at 6.25V. 10/24 M27W201 Device Description 2.9 Electronic Signature The Electronic Signature (ES) mode allows the reading out of a binary code from an EPROM that will identify its manufacturer and type. This mode is intended for use by programming equipment to automatically match the device to be programmed with its corresponding programming algorithm. The ES mode is functional in the 25°C ± 5°C ambient temperature range that is required when programming the M27W201. To activate the ES mode, the programming equipment must force 11.5V to 12.5V on address line A9 of the M27W201 with VPP = VCC = 5V. Two identifier bytes may then be sequenced from the device outputs by toggling address line A0 from VIL to VIH. All other address lines must be held at VIL during Electronic Signature mode. Byte 0 (A0 = VIL) repres ents the manufacturer code and byte 1 (A0 = VIH) the device identifier code. For the STMicroelectronics M27W201, these two identifier bytes are given in Table 3 and can be read-out on outputs Q7 to Q0. Note that the M27W201 and M27C2001 have the same identifier byte. Table 3. Electronic Signature A0 VIL VIH Q7 0 0 Q6 0 1 Q5 1 1 Q4 0 0 Q3 0 0 Q2 0 0 Q1 0 0 Q0 0 1 Hex Data 20h 61h Identifier Manufacturer’s Code Device Code 2.10 Erasure operation (applies to UV EPROM) The erasure characteristics of the M27W201 are such that erasure begins when the cells are exposed to light with wavelengths shorter than approximately 4000 Å. It should be noted that sunlight and some type of fluorescent lamps have wavelengths in the 3000-4000 Å range. Data shows that constant exposure to room level fluorescent lighting could erase a typical M27W201 in about 3 years, while it would take approximately 1 week to cause erasure when exposed to direct sunlight. If the M27W201 is to be exposed to these types of lighting conditions for extended periods of time, it is suggested that opaque labels be put over the M27W201 window to prevent unintentional erasure. The recommended erasure procedure for the M27W201 is exposure to short wave ultraviolet light which has wavelength of 2537 Å. The integrated dose (i.e. UV intensity x exposure time) for erasure should be a minimum of 15 W-sec/cm2. The erasure time with this dosage is approximately 15 to 20 minutes using an ultraviolet lamp with 12000 µW/cm2 power rating. The M27W201 should be placed within 2.5 cm (1 inch) of the lamp tubes during the erasure. Some lamps have a filter on their tubes which should be removed before erasure. 11/24 Maximum ratings M27W201 3 Maximum ratings Table 4. Symbol TA TBIAS TSTG VIO (3) VCC VA9 (3) Absolute Maximum Ratings (1) Parameter Ambient Operating Temperature (2) Temperature Under Bias Storage Temperature Input or Output Voltage (except A9) Supply Voltage A9 Voltage Program Supply Voltage Value –40 to 125 –50 to 125 –65 to 150 –2 to 7 –2 to 7 –2 to 13.5 –2 to 14 Unit °C °C °C V V V V VPP 1. Except for the rating “Operating Temperature Range”, stresses above those listed in the Table “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only and operation of the device at these or any other conditions above those indicated in the Operating sections of this specification is not implied. Exposure to Absolute Maximum Rating conditions for extended periods may affect device reliability. Refer also to the STMicroelectronics SURE Program and other relevant quality documents. 2. Depends on range. 3. Minimum DC voltage on Input or Output is –0.5V with possible undershoot to –2.0V for a period less than 20ns. Maximum DC voltage on Output is VCC +0.5V with possible overshoot to VCC +2V for a period less than 20ns. 12/24 M27W201 DC and AC parameters 4 DC and AC parameters TA = –40 to 85°C; VCC = 2.7V to 3.6V; VPP = VCC Table 5. Symbol ILI ILO ICC ICC1 ICC2 IPP VIL VIH (2) VOL VOH Read Mode DC Characteristics (1) Parameter Input Leakage Current Output Leakage Current Supply Current Supply Current (Standby) TTL Supply Current (Standby) CMOS Program Current Input Low Voltage Input High Voltage Output Low Voltage Output High Voltage TTL IOL = 2.1mA IOH = –400µA 2.4 Test Condition 0V ≤ VIN ≤ VCC 0V ≤ VOUT ≤ VCC E = VIL, G = VIL, IOUT = 0mA, f = 5MHz, VCC ≤ 3.6V E = VIH E > VCC – 0.2V, VCC ≤ 3.6V VPP = VCC –0.3 Min. Max. ±10 ±10 15 1 15 10 0.2VCC Unit µA µA mA mA µA µA V V V V 0.7VCC VCC + 0.5 0.4 1. VCC must be applied simultaneously with or before VPP and removed simultaneously or after VPP. 2. Maximum DC voltage on Output is VCC +0.5V. TA = 25 °C; VCC = 6.25V ± 0.25V; VPP = 12.75V ± 0.25V Table 6. Symbol ILI ICC IPP VIL VIH VOL VOH VID Programming Mode DC Characteristics (1) Parameter Input Leakage Current Supply Current Program Current Input Low Voltage Input High Voltage Output Low Voltage Output High Voltage TTL A9 Voltage IOL = 2.1mA IOH = –400µA 2.4 11.5 12.5 E = VIL –0.3 2.0 Test Condition 0 ≤ VIN ≤ VCC Min Max ±10 50 50 0.8 VCC + 0.5 0.4 Unit µA mA mA V V V V V 1. VCC must be applied simultaneously with or before VPP and removed simultaneously or after VPP. 13/24 DC and AC parameters Table 7. AC Measurement Conditions Parameter Input Rise and Fall Times Input Pulse Voltages Input and Output Timing Ref. Voltages High Speed ≤ 10ns 0 to 3V 1.5V M27W201 Standard ≤ 20ns 0.4V to 2.4V 0.8V and 2V TA = 25 °C, f = 1 MHz Table 8. Symbol CIN COUT Capacitance (1) Parameter Input Capacitance Output Capacitance Test Condition VIN = 0V VOUT = 0V Min. Max. 6 12 Unit pF pF 1. Sampled only, not 100% tested. Figure 6. AC Testing Input Output Waveform High Speed 3V 1.5V 0V Standard 2.4V 2.0V 0.8V AI01822 0.4V Figure 7. AC Testing Load Circuit 1.3V 1N914 3.3kΩ DEVICE UNDER TEST CL OUT CL = 30pF for High Speed CL = 100pF for Standard CL includes JIG capacitance AI01823B 14/24 M27W201 TA = –40 to 85 °C; VCC = 2.7V to 3.6V; VPP = VCC Table 9. Read Mode AC Characteristics (1) -80 (2) Symbol Alt Parameter Test Condition VCC = 3.0V to 3.6V Min. tAVQV tELQV tGLQV tEHQZ (3) tGHQZ (3) tAXQX tACC tCE tOE tDF tDF tOH Address Valid to Output Valid Chip Enable Low to Output Valid Output Enable Low to Output Valid Chip Enable High to Output Hi-Z Output Enable High to Output Hi-Z Address Transition to Output Transition E = VIL, G = VIL G = VIL E = VIL G = VIL E = VIL E = VIL, G = VIL 0 0 0 Max. 70 70 40 40 40 0 0 0 VCC = 2.7V to 3.6V Min. Max. 80 80 50 50 50 DC and AC parameters -100 (-120/-150/-200) VCC = 2.7V to 3.6V Min. Max. 100 100 60 0 0 0 60 60 ns ns ns ns ns ns Unit 1. VCC must be applied simultaneously with or before VPP and removed simultaneously or after VPP. 2. Speed obtained with High Speed AC measurement conditions. 3. Sampled only, not 100% tested. Figure 8. Read Mode AC Waveforms A0-A17 VALID tAVQV E tGLQV G tELQV Q0-Q7 tGHQZ Hi-Z tEHQZ tAXQX VALID AI00719B 15/24 DC and AC parameters TA = 25 °C; VCC = 6.25V ± 0.25V; VPP = 12.75V ± 0.25V Table 10. Symbol tAVPL tQVPL tVPHPL tVCHPL tELPL tPLPH tPHQX tQXGL tGLQV tGHQZ (2) tGHAX M27W201 Programming Mode AC Characteristics (1) Alt tAS tDS tVPS tVCS tCES tPW tDH tOES tOE tDFP tAH Parameter Address Valid to Program Low Input Valid to Program Low VPP High to Program Low VCC High to Program Low Chip Enable Low to Program Low Program Pulse Width Program High to Input Transition Input Transition to Output Enable Low Output Enable Low to Output Valid Output Enable High to Output Hi-Z Output Enable High to Address Transition 0 0 Test Condition Min. 2 2 2 2 2 95 2 2 100 130 105 Max. Unit µs µs µs µs µs µs µs µs ns ns ns 1. VCC must be applied simultaneously with or before VPP and removed simultaneously or after VPP. 2. Sampled only, not 100% tested. Figure 9. Programming and Verify Modes AC Waveforms A0-A17 tAVPL Q0-Q7 tQVPL VPP tVPHPL VCC tVCHPL E tELPL P tPLPH G tQXGL tGHAX tGLQV tGHQZ DATA IN tPHQX DATA OUT VALID PROGRAM VERIFY AI00720 16/24 M27W201 Package mechanical data 5 5.1 Package mechanical data 32-pin Ceramic Frit-seal DIP, with round window (FDIP32WA) Figure 10. FDIP32WA package outline A2 A3 A1 B1 B D2 D S N ∅ 1 A L α eA eB C e E1 E FDIPW-a Table 11. Symbol FDIP32WA package mechanical data millimeters Min Typ Max 5.72 0.51 3.91 3.89 0.41 1.45 0.23 41.73 38.10 2.54 15.24 13.06 14.99 16.18 3.18 32 1.52 7.11 4° 11° 4° 2.49 0.060 0.280 11° 18.03 4.10 0.637 0.125 32 0.098 13.36 0.514 0.590 0.710 0.161 0.30 42.04 0.009 1.643 1.500 0.100 0.600 0.526 1.40 4.57 4.50 0.56 0.020 0.154 0.153 0.016 0.057 0.012 1.655 Min inches Typ Max 0.225 0.055 0.180 0.177 0.022 A A1 A2 A3 B B1 C D D2 e E E1 eA eB L N S Ø α 17/24 Package mechanical data M27W201 5.2 32-pin Plastic DIP, 600 mils width (PDIP32) Figure 11. PDIP32 package outline A2 A1 b1 b D2 D S N A L α eA c e E1 1 E PDIP-C Table 12. Symbol PDIP32 package mechanical data millimeters Min Typ Max 4.83 0.38 3.81 0.41 1.14 0.23 41.78 38.10 15.24 2.54 15.24 13.46 1.65 3.05 0° 32 15.88 13.97 2.21 3.56 15° 0.600 0.530 0.065 0.120 0° 32 0.53 1.65 0.38 42.29 0.016 0.045 0.009 1.645 1.500 0.600 0.100 0.625 0.550 0.087 0.140 15° 0.015 0.150 0.021 0.065 0.015 1.665 Min inches Typ Max 0.190 A A1 A2 b b1 c D D2 eA e E E1 S L α N 18/24 M27W201 Package mechanical data 5.3 32-lead Rectangular Plastic Leaded Chip Carrier (PLCC32) Figure 12. PLCC32 package outline D D1 1N A1 A2 B1 E2 E3 E1 E e F 0.51 (.020) 1.14 (.045) D3 R CP A E2 B D2 D2 PLCC-A Table 13. Symbol PLCC32 package mechanical data millimeters Min Typ Max 3.56 2.41 – 0.53 0.81 0.10 12.32 11.35 4.78 7.62 14.86 13.89 6.05 10.16 1.27 0.00 0.89 32 0.13 0.000 0.035 32 15.11 14.05 6.93 0.585 0.547 0.238 0.400 0.050 0.005 12.57 11.51 5.66 0.485 0.447 0.188 0.300 0.595 0.553 0.273 Min 0.125 0.060 0.015 0.013 0.026 inches Typ Max 0.140 0.095 – 0.021 0.032 0.004 0.495 0.453 0.223 A A1 A2 B B1 CP D D1 D2 D3 E E1 E2 E3 e F R N 3.18 1.53 0.38 0.33 0.66 19/24 Package mechanical data M27W201 5.4 32-lead Plastic Thin Small Outline, 8 x 20 mm (TSOP32) Figure 13. TSOP32 package outline A2 1 N e E B N/2 D1 D A CP DIE C TSOP-a A1 α L Table 14. Symbol TSOP32 package mechanical data millimeters Min Typ Max 1.200 0.050 0.950 0.170 0.100 0.150 1.050 0.250 0.210 0.100 19.800 18.300 – 7.900 0.500 32 0° 5° 0° 0.500 20.200 18.500 – 8.100 0.700 0.7795 0.7205 – 0.3110 0.0197 32 5° 0.0197 0.0020 0.0374 0.0067 0.0039 Min inches Typ Max 0.0472 0.0059 0.0413 0.0098 0.0083 0.0039 0.7953 0.7283 – 0.3189 0.0276 A A1 A2 B C CP D D1 e E L N α 20/24 M27W201 Package mechanical data 5.5 32-lead Plastic Thin Small Outline, 8x 14 mm (TSOP32) Figure 14. TSOP32 package outline A2 1 N e E B N/2 D1 D A CP DIE C TSOP-a A1 α L Table 15. Symbol TSOP32 package mechanical data millimeters Min Typ Max 1.200 0.050 0.950 0 0.170 0.100 0.150 1.050 5 0.270 0.210 0.100 13.800 12.300 – 7.900 0.500 32 0.500 14.200 12.500 – 8.100 0.700 0.5433 0.4843 – 0.3110 0.0197 32 0.0197 0.0020 0.0374 0 0.0067 0.0039 Min inches Typ Max 0.0472 0.0059 0.0413 5 0.0106 0.0083 0.0039 0.5591 0.4921 – 0.3189 0.0276 A A1 A2 a B C CP D D1 e E L N 21/24 Part numbering M27W201 6 Part numbering Table 16. Example: Device Type M27 Supply Voltage W = 2.7V to 3.6V Device Function 201 = 2 Mbit (256Kb x 8) Speed -80 (1) (2) = 80 ns -100 = 100 ns Not For New Design (3) -120 = 120 ns -150 = 150 ns -200 = 200 ns Package F = FDIP32W (4) B = PDIP32 K = PLCC32 N = TSOP32: 8 x 20 mm (4) NZ = TSOP32: 8 x 14 mm (4) Temperature Range 6 = –40 to 85 °C Options TR = ECOPACK® package, Tape & Reel Packing 1. High Speed, see AC Characteristics section for further information. 2. This speed also guarantees 70ns access time at VCC = 3.0V to 3.6V. 3. These speeds are replaced by the 100ns. 4. Packages option available on request. Please contact STMicroelectronics local Sales Office. Ordering Information Scheme M27W201 -80 K 6 TR For a list of available options (speed, package, etc...) or for further information on any aspect of this device, please contact the STMicroelectronics Sales Office nearest to you. 22/24 M27W201 Revision history 7 Revision history Table 17. Date 25-Jul-1999 19-Apr-2000 24-Oct-2001 12-Apr-2006 Document revision history Revision 1 2 3 4 First Issue FDIP32W Package Dimension, L Max added (Table 11) TSOP32 Package Dimension changed (Table 14) 0 to 70°C Temperature Range deleted, Programming Time changed TSOP32 8x14mm added Converted to new template. Added ECOPACK® information. Changes 23/24 M27W201 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZE REPRESENTATIVE OF ST, ST PRODUCTS ARE NOT DESIGNED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS, WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2006 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 24/24