M28256

M28256 256 Kbit (32Kb x8) Parallel EEPROM with Software Data Protection PRELIMINARY DATA FAST ACCESS TIME: – 90ns at 5V – 120ns at 3V SINGLE SUPPLY VOLTAGE: – 5V ± 10% for M28256 – 2.7V to 3.6V for M28256-xxW LOW POWER CONSUMPTION FAST WRITE CYCLE: – 64 Bytes Page Write Operation – Byte or Page Write Cycle ENHANCED END of WRITE DETECTION: – Data Polling – Toggle Bit STATUS REGISTER HIGH RELIABILITY DOUBLE POLYSILICON, CMOS TECHNOLOGY: – Endurance >100,000 Erase/Write Cycles – Data Retention >10 Years JEDEC APPROVED BYTEWIDE PIN OUT ADDRESS and DATA LATCHED ON-CHIP SOFTWARE DATA PROTECTION 28 1 PDIP28 (BS) PLCC32 (KA) 28 1 SO28 (MS) 300 mils TSOP28 (NS) 8 x13.4mm Figure 1. Logic Diagram VCC DESCRIPTION The M28256 and M28256-Ware 32K x8 low power Parallel EEPROM fabricatedwith STMicroelectronics proprietary double polysilicon CMOS technology. Table 1. Signal Names A0-A14 DQ0-DQ7 W E G VCC VSS Address Input Data Input / Output Write Enable Chip Enable Output Enable Supply Voltage Ground 15 A0-A14 8 DQ0-DQ7 W E G M28256 VSS AI01885 January 1999 This is preliminary information on a new product now in developmentor undergoing evaluation . Detail s are subject to change without notice. 1/21 M28256 Figure 2A. DIP Pin Connections Figure 2B. LCC Pin Connections AI01886 AI01887 Warning: NC = Not Connected, DU = Don’t Use. Figure 2C. SO Pin Connections Figure 2D. TSOP Pin Connections A14 A12 A7 A6 A5 A4 A3 A2 A1 A0 DQ0 DQ1 DQ2 VSS 1 2 3 4 5 6 7 M28256 8 9 10 11 12 13 14 28 27 26 25 24 23 22 21 20 19 18 17 16 15 AI01888 VCC W A13 A8 A9 A11 G A10 E DQ7 DQ6 DQ5 DQ4 DQ3 G A11 A9 A8 A13 W VCC A14 A12 A7 A6 A5 A4 A3 22 DQ1 DQ2 VSS DU DQ3 DQ4 DQ5 21 28 1 M28256 15 14 7 8 AI01889 A14 A12 A7 A6 A5 A4 A3 A2 A1 A0 DQ0 DQ1 DQ2 VSS 1 28 2 27 3 26 4 25 5 24 6 23 7 22 M28256 8 21 9 20 10 19 11 18 12 17 13 16 14 15 VCC W A13 A8 A9 A11 G A10 E DQ7 DQ6 DQ5 DQ4 DQ3 A6 A5 A4 A3 A2 A1 A0 NC DQ0 A7 A12 A14 DU VCC W A13 1 32 A8 A9 A11 NC G A10 E DQ7 DQ6 9 M28256 25 17 A10 E DQ7 DQ6 DQ5 DQ4 DQ3 VSS DQ2 DQ1 DQ0 A0 A1 A2 2/21 M28256 Table 2. Absolute Maximum Ratings (1) Symbol TA T STG VCC V IO VI VESD Parameter Ambient Operating Temperature Storage Temperature Range Supply Voltage Input/Output Voltage Input Voltage Electrostatic Discharge Voltage (Human Body model) (3) (2) Value – 40 to 85 – 65 to 150 – 0.3 to 6.5 – 0.3 to VCC +0.6 – 0.3 to 6.5 4000 Unit °C °C V V V V Notes: 1. Except for the rating ”Operating Temperature Range”, stresses above those listed in the Table ”Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only and operation of the device at these or any other conditions above those indicated in the Operating sections of this specification is not implied. Exposure to Absolute Maximum Rating conditions for extended periods may affect device reliability. Refer also to the STMicroelectronics SURE Program and other relevant quality documents. 2. Depends on range. 3. 100pF through 1500 Ω; MIL-STD-883C, 3015.7 Figure 3. Block Diagram E G W VPP GEN RESET CONTROL LOGIC X DECODE A6-A14 (Page Address) ADDRESS LATCH 256K ARRAY A0-A5 ADDRESS LATCH Y DECODE SENSE AND DATA LATCH I/O BUFFERS PAGE LOAD TIMER STATUS TOGGLE BIT DATA POLLING AI01697 DQ0-DQ7 3/21 M28256 Table 3. Operating Modes (1) M ode Read Write Standby / Write Inhibit Write Inhibit Write Inhibit Output Disable Notes: 1. X = VIH or VIL. E VIL VIL VIH X X X G VIL VIH X X VIL VIH W VIH VIL X VIH X X DQ0 - DQ7 Data Out Data In Hi-Z Data Out or Hi-Z Data Out or Hi-Z Hi-Z DESCRIPTION (Cont’d) The devices offer fast access time with low power dissipation and requires a 5V or 3V power supply. The circuit has been designed to offer a flexible microcontroller interface featuring both hardware and software handshaking with Data Polling and Toggle Bit and access to a status register. The devices support a 64 byte page write operation. A Software Data Protection (SDP) is also possible using the standard JEDEC algorithm. PIN DESCRIPTION Addresses (A0-A14). The address inputs select an 8-bit memory location during a read or write operation. Chip Enable (E). The chip enable input must be low to enable all read/write operations.When Chip Enable is high, power consumption is reduced. Output Enable (G). The Output Enable input controls the data output buffers and is used to initiate read operations. Data In/ Out (DQ0- DQ7). Data is written to or read from the memory through the I/O pins. Write Enable (W). The Write Enable input controls the writing of data to the memory. OPERATIONS Write Protection In order to prevent data corruption and inadvertent write operations; an internal VCC comparatorinhibits Write operations if VCC is below VWI (see Table 7 andTable 9).Access to the memoryin write mode is allowed after a power-up as specified in Table 7 and Table 9. Read The device is accessed like a static RAM. When E and G are low with W high, the data addressed is presented on the I/O pins. The I/O pins are high impedance when either G or E is high. Write Write operations are initiated when both W and E are low and G is high.The device supports both E and W controlled write cycles. The Address is latched by the falling edge of E or W which ever occurs last and the Data on the rising edge of E or W which ever occurs first. Once initiated the write operation is internally timed until completion and the status of the Data Polling and the Toggle Bit functions on DQ7 and DQ6 is controlled accordingly. Page Write Page write allows up to 64 bytes within the same page to be consecutively latched into the memory prior to initiating a programming cycle. All bytes must be located in a single page address, that is A14-A6 must be the same for all bytes; if not, the Page Write instruction is not executed. The page write can be initiated by any byte write operation. A page write is composed of successive Write instructions which have to be sequenced with a specific period of time between two consecutive Write instructions, period of time which has to be smaller than the tWHWH value (see Table 12 and Table 13). If this period of time exceeds the tWHWH value, the internal programmingcycle will start. Once initiated the write operation is internally timed until completion and the status of the Data Polling and the Toggle Bit functions on DQ7 and DQ6 is controlled accordingly. 4/21 M28256 Status Register The devices provide several Write operation status flags that can be used to minimize the application write time. These signals are available on the I/O port bits during programming cycle only. Data Polling bit (DQ7). During the internal write cycle, any attempt to read the last byte written will produce on DQ7 the complementary value of the previously latched bit. Once the write cycle is finished the true logic value appears on DQ7 in the read cycle. Toggle bit (DQ6). The devices offer another way for determining when the internal write cycle is completed. During the internal Erase/Write cycle, DQ6 will toggle from ”0” to ”1” and ”1” to ”0” (the first read value is ”0”) on subsequent attempts to read any byte of the memory. When the internal cycle is completed the toggling will stop and the data read on DQ7-DQ0 is the addressed memory byte. The device is now accessible for a new Read or Write operation. Page Load TimerStatus bit(DQ5). Duringa Page Write instruction, the devices expect to receive the stream of data with a minimum period of time between each data byte. This period of time (tWHWH) is defined by the on-chip Page Load timer which running/overflow status is available on DQ5. DQ5 Low indicates that the timer is running, DQ5 High indicates the time-out after which the internal write cycle will start. Figure 4. Status Bit Assignment DQ7 DQ6 DQ5 DQ4 DQ3 DQ2 DQ1 DQ0 DP TB PLTS X X X X X DP = Data Polling TB = Toggle Bit PLTS = Page Load Timer Status Software Data Protection The devices offer a software controlled write protection facility that allows the user to inhibit all write modes to the device. This can be useful in protecting the memory from inadvertent write cycles that may occur due to uncontrolledbus conditions. The devices are shipped as standardin the ”unprotected” state meaning that the memory contents can be changed as required by the user. After the Software Data Protection enable algorithm is issued, the device enters the ”Protect Mode” of operation where no further write commands have any effect on the memory contents. The devices remain in this mode until a valid Software Data Protection (SDP) disable sequence is received whereby the device reverts to its ”unprotected” state. The Software Data Protection is fully non-volatile and is not changed by power on/off sequences. To enable the Software Data Protection (SDP) the device requires the user to write (with a Page Write addressing three specific data bytes to three specific memorylocations,each location in a different page) as per Figure 6. Similarly to disable the Software Data Protection the user has to write specific data bytes into six different locations as per Figure 5 (with a Page Write adressing different bytes in different pages). This complexseries ensures that the userwill never enable or disable the Software Data Protection accidentally. To write into the devices when SDP is set, the sequence shown in Figure 6 must be used. This sequence provides an unlock key to enable the write action, and at the same time SDP continues to be set. An extension to this is where SDP is required to be set, and data is to be written. Using the same sequence as above, the data can be written and SDP is set at the same time, giving both these actions in the same Write cycle (tWC). 5/21 WRITE AAh in Address 5555h WRITE 55h in Address 2AAAhWRITE A0h in Address 5555h AI01698B M28256 Table 4. AC Measurement Conditions Input Rise and Fall Times Input Pulse Voltages (M28256) Input Pulse Voltages (M28256-W) Input and Output Timing Ref. Voltages (M28256) Input and Output Timing Ref. Voltages (M28256-W) ≤ 20ns 0.4V to 2.4V 0V to V CC –0.3V 0.8V to 2.0V 0.5 VCC Figure 7. AC Testing Input Output Waveforms 4.5V to 5.5V Operating Voltage 2.4V 2.0V 0.8V Figure 8. AC Testing Equivalent Load Circuit 0.4V IOL DEVICE UNDER TEST IOH CL = 100pF OUT 2.7V to 3.6V Operating Voltage VCC – 0.3V 0.5 VCC 0V AI02101B CL includes JIG capacitance AI02102B Table 5. Capacitance (1) (TA = 25 °C, f = 1 MHz ) Symbol CIN C OUT Parameter Input Capacitance Output Capacitance Test Condition VIN = 0V VOUT = 0V Min Max 6 12 Unit pF pF Note: 1. Sampled only, not 100% tested. Table 6. Read Mode DC Characteristics for M28256 (TA = 0 to 70°C or –40 to 85°C; VCC = 4.5V to 5.5V) Symbol ILI ILO ICC (1) Parameter Input Leakage Current Output Leakage Current Supply Current (TTL inputs) Supply Current (CMOS inputs) Test Condition 0V ≤ VIN ≤ VCC 0V ≤ VIN ≤ VCC E = VIL, G = VIL , f = 5 MHz E = VIL, G = VIL , f = 5 MHz E = VIH E > VCC –0.3V Min Max 10 10 30 25 1 100 Unit µA µA mA mA mA µA V V V ICC1 ICC2 (1) (1) Supply Current (Standby) TTL Supply Current (Standby) CMOS Input Low Voltage Input High Voltage Output Low Voltage Output High Voltage VIL VIH VOL VOH – 0.3 2 IOL = 2.1 mA IOH = –400 µA 2.4 0.8 VCC + 0.5 0.4 Note: 1. All I/O’s open circuit. 7/21 M28256 Table 7. Power Up Timing for M28256 (1) (TA = 0 to 70°C or –40 to 85°C; VCC = 4.5V to 5.5V) Symbol tPUR tPUW VWI Parameter Time Delay to Read Operation Time Delay to Write Operation (once VCC ≥ VWI) Write Inhibit Threshold 3.0 Min Max 1 5 4.2 Unit µs ms V Note: 1. Sampled only, not 100% tested. Table 8. Read Mode DC Characteristics for M28256-W (TA = 0 to 70°C or –40 to 85°C; VCC = 2.7V to 3.6V) Symbol ILI ILO ICC ICC2 (1) Parameter Input Leakage Current Output Leakage Current Supply Current (CMOS inputs) Supply Current (Standby) CMOS Input Low Voltage Input High Voltage Output Low Voltage Output High Voltage Test Condition 0V ≤ VIN ≤ VCC 0V ≤ VIN ≤ VCC E = VIL, G = VIL, f = 5 MHz, V CC = 3.3V E = VIL, G = VIL, f = 5 MHz, V CC = 3.6V Min Max 10 10 15 15 20 Unit µA µA mA mA µA V V V V (1) E > VCC –0.3V – 0.3 2 IOL = 2.1 mA IOH = –400 µA 0.8 VCC VIL VIH VOL VOH 0.6 VCC + 0.5 0.2 VCC Note: 1. All I/O’s open circuit. Table 9. Power Up Timing for M28256-W (1) (TA = 0 to 70°C or –40 to 85°C; VCC = 2.7V to 3.6V) Symbol tPUR tPUW VWI Parameter Time Delay to Read Operation Time Delay to Write Operation (once VCC ≥ VWI) Write Inhibit Threshold 1.5 Min Max 1 10 2.5 Unit µs ms V Note: 1. Sampled only, not 100% tested. 8/21 M28256 Table 10. Read Mode AC Characteristics (TA = 0 to 70°C or –40 to 85°C; VCC = 4.5V to 5.5V) M28256 Symbol Alt Parameter Test Condition -90 min max tAVQV tELQV tGLQV tEHQZ (1) tGHQZ (1) tAXQX tACC tCE tOE tDF tDF tOH Address Valid to Output Valid Chip Enable Low to Output Valid Output Enable Low to Output Valid Chip Enable High to Output Hi-Z Output Enable High to Output Hi-Z Address Transition to Output Transition E = VIL, G = VIL G = VIL E = VIL G = VIL E = VIL E = VIL, G = VIL 0 0 0 90 90 40 40 40 0 0 0 -12 -15 -20 min max 200 200 50 0 0 0 50 50 ns ns ns ns ns ns Unit min max min max 120 120 45 45 45 0 0 0 150 150 50 50 50 Note: 1. Output Hi-Z is defined as the point at which data is no longer driven. Table 11. Read Mode AC Characteristics (TA = 0 to 70°C or –40 to 85°C; VCC = 2.7V to 3.6V) M28256-W Symbol Alt Parameter Test Condition -12 min max tAVQV tELQV tGLQV tEHQZ (1) -15 -20 -25 min max 250 250 100 0 0 0 60 60 Unit min max min max 150 150 70 0 0 0 50 50 0 0 0 200 200 80 55 55 tACC tCE tOE tDF tDF tOH Address Valid to Output Valid Chip Enable Low to Output Valid Output Enable Low to Output Valid Chip Enable High to Output Hi-Z Output Enable High to Output Hi-Z Address Transition to Output Transition E = VIL, G = VIL G = VIL E = VIL G = VIL E = VIL E = VIL, G = VIL 0 0 0 120 120 45 45 45 ns ns ns ns ns ns tGHQZ (1) tAXQX Note: 1. Output Hi-Z is defined as the point at which data is no longer driven. 9/21 M28256 Table 12. Write Mode AC Characteristics (TA = 0 to 70°C or –40 to 85°C; VCC = 4.5V to 5.5V) Symbol Alt Parameter Test Condition M28256 Min tAVWL tAVEL tELWL tGHWL tGHEL tWLEL tWLAX tELAX tWLDV tELDV tELEH tWHEH tWHGL tEHGL tEHWH tWHDX tEHDX tWHWL tWLWH tWHWH tWHRH tEL, tWL tDVWH tDVEH tDS tDS tAS tAS tCES tOES tOES tWES tAH tAH tDV tDV tWP tCEH tOEH tOEH tWEH tDH tDH tWPH tWP tBLC tWC Address Valid to Write Enable Low Address Valid to Chip Enable Low Chip Enable Low to Write Enable Low Output Enable High to Write Enable Low Output Enable High to Chip Enable Low Write Enable Low to Chip Enable Low Write Enable Low to Address Transition Chip Enable Low to Address Transition Write Enable Low to Input Valid Chip Enable Low to Input Valid Chip Enable Low to Chip Enable High Write Enable High to Chip Enable High Write Enable High to Output Enable Low Chip Enable High to Output Enable Low Chip Enable High to Write Enable High Write Enable High to Input Transition Chip Enable High to Input Transition Write Enable High to Write Enable Low Write Enable Low to Write Enable High Byte Load Repeat Cycle Time Write Cycle Time E or W Input Filter Pulse Width Data Valid before Write Enable High Data Valid before Chip Enable High Note 1 10 50 50 E = VIL, G = VIH G = VIH, W = VIL 50 0 0 0 0 0 0 100 50 0.15 150 5 E = VIL, G = VIH G = VIH, W = VIL G = VIH E = VIL W = VIL G = VIH 0 0 0 0 0 0 50 50 1 1 Max ns ns ns ns ns ns ns ns µs µs ns ns ns ns ns ns ns ns ns µs ms ns ns ns Unit Note: 1. Characterized only but not tested in production. 10/21 M28256 Table 13. Write Mode AC Characteristics (TA = 0 to 70°C or –40 to 85°C; VCC = 2.7V to 3.6V) Symbol Alt Parameter Test Condition M28256-W Min tAVWL tAVEL tELWL tGHWL tGHEL tWLEL tWLAX tELAX tWLDV tELDV tELEH tWHEH tWHGL tEHGL tEHWH tWHDX tEHDX tWHWL tWLWH tWHWH tWHRH tEL, tWL tDVWH tDVEH tDS tDS tAS tAS tCES tOES tOES tWES tAH tAH tDV tDV tWP tCEH tOEH tOEH tWEH tDH tDH tWPH tWP tBLC tWC Address Valid to Write Enable Low Address Valid to Chip Enable Low Chip Enable Low to Write Enable Low Output Enable High to Write Enable Low Output Enable High to Chip Enable Low Write Enable Low to Chip Enable Low Write Enable Low to Address Transition Chip Enable Low to Address Transition Write Enable Low to Input Valid Chip Enable Low to Input Valid Chip Enable Low to Chip Enable High Write Enable High to Chip Enable High Write Enable High to Output Enable Low Chip Enable High to Output Enable Low Chip Enable High to Write Enable High Write Enable High to Input Transition Chip Enable High to Input Transition Write Enable High to Write Enable Low Write Enable Low to Write Enable High Byte Load Repeat Cycle Time Write Cycle Time E or W Input Filter Pulse Width Data Valid before Write Enable High Data Valid before Chip Enable High Note 1 10 50 50 E = VIL, G = VIH G = VIH, W = VIL 100 0 0 0 0 0 0 100 100 0.2 150 5 E = VIL, G = VIH G = VIH, W = VIL G = VIH E = VIL W = VIL G = VIH 0 0 0 0 0 0 70 70 1 1 Max ns ns ns ns ns ns ns ns µs µs ns ns ns ns ns ns ns ns ns µs ms ns ns ns Unit Note: 1. Characterized only but not tested in production. 11/21 M28256 Figure 9. Read Mode AC Waveforms A0-A14 tAVQV E tGLQV G tELQV DQ0-DQ7 VALID tAXQX tEHQZ tGHQZ DATA OUT Hi-Z AI01700 Note: Write Enable (W) = High. Figure 10. Write Mode AC Waveforms - Write Enable Controlled A0-A14 tAVWL E tELWL G tGHWL W VALID tWLAX tWHEH tWLWH tWHGL tWLDV DQ0-DQ7 DATA IN tDVWH tWHWL tWHDX AI01701 12/21 M28256 Figure 11. Write Mode AC Waveforms - Chip Enable Controlled A0-A14 tAVEL E tGHEL G tWLEL W VALID tELAX tELEH tEHGL tELDV DQ0-DQ7 DATA IN tDVEH tEHDX tEHWH AI01702 Figure 12. Page Write Mode AC Waveforms - Write Enable Controlled A0-A14 Addr 0 Addr 1 Addr 2 Addr n E G tWHWL W tWLWH DQ0-DQ7 Byte 0 Byte 1 tWHWH Byte 2 tWHWH Byte n tWHRH DQ5 Byte n AI01703B 13/21 M28256 Figure 13. Software Protected Write Cycle Waveforms G E tWLWH W tAVEL A0-A5 tWHDX A6-A14 5555h tDVWH DQ0-DQ7 AAh 55h A0h Byte 0 Byte 62 Byte 63 AI01704 tWHWL tWHWH tWLAX Byte Address 2AAAh 5555h Page Address Note: A6 through A14 must specify the same page address during each high to low transition of W (or E) after the software code has been entered. G must be high only when W and E are both low. Figure 14. Data Polling Waveform Sequence A0-A14 Address of the last byte of the Page Write instruction E G W DQ7 DQ7 DQ7 DQ7 DQ7 DQ7 LAST WRITE INTERNAL WRITE SEQUENCE READY AI01705 14/21 M28256 Figure 15. Toggle Bit Waveform Sequence A0-A14 E G W DQ6 (1) DQ6 DQ6 LAST WRITE TOGGLE INTERNAL WRITE SEQUENCE READY AI01706 Note: 1. First Toggle bit is forced to ’0’. 15/21 M28256 ORDERING INFORMATION SCHEME Example: M28256 – 15 W KA 6 T Speed 90 12 15 20 25 (2) (1) Operating Voltage blank W 4.5V to 5.5V 2.7V to 3.6V Package BS PDIP28 KA PLCC32 MS SO28 300 mils NS TSOP28 8 x 13.4mm Temperature Range 1 (3) Option T Tape & Reel Packing 90ns 120ns 150ns 200ns 250ns 0 to 70 °C –40 to 85 °C 6 Notes: 1. Not available for ”W” operating voltage. 2. Available for ”W” operating voltage only. 3. Temperature Range on request only. Devices are shipped from the factory with the memory content set at all ”1’s” (FFh). For a list of available options (Speed, Package, etc...) or for further informationon any aspect of this device, please contact the STMicroelectronics Sales Office nearest to you. 16/21 M28256 PDIP28 - 28 pin Plastic DIP, 600 mils width Symb Typ A A1 A2 B B1 C D D2 E E1 e1 eA eB L S α N 2.54 14.99 33.02 15.24 1.52 mm Min – 0.38 3.56 0.38 – 0.20 36.83 – – 13.59 – – 15.24 3.18 1.78 0° 28 Max 5.08 – 4.06 0.51 – 0.30 37.34 – – 13.84 – – 17.78 3.43 2.08 10° 0.100 0.590 1.300 0.600 0.060 Typ inches Min – 0.015 0.140 0.015 – 0.008 1.450 – – 0.535 – – 0.600 0.125 0.070 0° 28 Max 0.200 – 0.160 0.020 – 0.012 1.470 – – 0.545 – – 0.700 0.135 0.082 10° A2 A1 B1 B D2 D S N A L α eA eB C e1 E1 1 E PDIP Drawing is not to scale. 17/21 M28256 PLCC32 - 32 lead Plastic Leaded Chip Carrier, rectangular Symb Typ A A1 A2 B B1 D D1 D2 E E1 E2 e F R N Nd Ne 0.89 1.27 mm Min 2.54 1.52 – 0.33 0.66 12.32 11.35 9.91 14.86 13.89 12.45 – 0.00 – 32 7 9 Max 3.56 2.41 0.38 0.53 0.81 12.57 11.56 10.92 15.11 14.10 13.46 – 0.25 – 0.035 0.050 Typ inches Min 0.100 0.060 – 0.013 0.026 0.485 0.447 0.390 0.585 0.547 0.490 – 0.000 – 32 7 9 Max 0.140 0.095 0.015 0.021 0.032 0.495 0.455 0.430 0.595 0.555 0.530 – 0.010 – D D1 1N A1 A2 B1 Ne E1 E F 0.51 (.020) D2/E2 B e 1.14 (.045) Nd A R CP PLCC Drawing is not to scale. 18/21 M28256 SO28 - 28 lead Plastic Small Outline, 300 mils body width Symb Typ A A1 B C D E e H L α N CP 1.27 mm Min 2.46 0.13 0.35 0.23 17.81 7.42 – 10.16 0.61 0° 28 0.10 Max 2.64 0.29 0.48 0.32 18.06 7.59 – 10.41 1.02 8° 0.050 Typ inches Min 0.097 0.005 0.014 0.009 0.701 0.292 – 0.400 0.024 0° 28 0.004 Max 0.104 0.011 0.019 0.013 0.711 0.299 – 0.410 0.040 8° A2 B e D A C CP N E 1 H A1 α L SO-b Drawing is not to scale. 19/21 M28256 TSOP28 - 28 lead Plastic Thin Small Outline, 8 x 13.4mm Symb Typ A A1 A2 B C D D1 E e L α N CP 0.55 0.95 0.17 0.10 13.20 11.70 7.90 0.50 0° 28 0.10 mm Min Max 1.25 0.20 1.15 0.27 0.21 13.60 11.90 8.10 0.70 5° 0.022 0.037 0.007 0.004 0.520 0.461 0.311 0.020 0° 28 0.004 Typ inches Min Max 0.049 0.008 0.045 0.011 0.008 0.535 0.469 0.319 0.028 5° A2 22 21 e 28 1 E B 7 8 D1 D A CP DIE C TSOP-c Drawing is not to scale. A1 α L 20/21 M28256 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Spec ifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics © 1999 STMicroelectronics - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - Canada - China - France - Germany - Italy - Japan - Korea - Malaysia - Malta - Mexico - Morocco - The Netherlands Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A. http://www.st.com 21/21