M74HC126YTTR

M74HC126 Quad bus buffer (3-state) Datasheet - production data • Balanced propagation delays: tPLH ≅ tPHL • Wide operating voltage range: VCC (opr) = 2 V to 6 V • Pin and function compatible with 74 series 126 SO14 TSSOP14 Features • ESD performance – CDM: 1 kV – HBM: 2 kV – MM: 200 V Description • High-speed: tPD = 8 ns (typ.) at VCC = 6 V The M74HC126 is a high-speed CMOS quad buffer (3-state) fabricated with silicon gate C2MOS technology. • Low power dissipation: ICC = 4 μA (max.) at TA = 25 °C The device requires the 3-state control input, G, to be set high to place the output into high impedance state. • High noise immunity: VNIH = VNIL = 28 % VCC (min) • Symmetrical output impedance: |IOH| = IOL = 6 mA (min.) All inputs are equipped with protection circuits against static discharge and transient excess voltage. Table 1. Device summary Order code Temp. range Package -55 °C to 125 °C S014 -40 °C to 125 °C SO14 (automotive grade) M74HC126TTR -55 °C to 125 °C TSSOP14 M74HC126YTTR(1) -40 °C to 125 °C TSSOP14 (automotive grade) M74HC126RM13TR (1) M74HC126YRM13TR Packaging Marking 74HC126 Tape and reel 74HC126Y HC126 HC126Y 1. Qualification and characterization according to AEC Q100 and Q003 or equivalent, advanced screening according to AEC Q001 and Q002 or equivalent. December 2013 This is information on a product in full production. DocID8021 Rev 3 1/14 www.st.com Contents M74HC126 Contents 1 Pin information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 Functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 4 Package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 4.1 SO14 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 4.2 TSSOP14 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 5 Ordering information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 6 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 2/14 DocID8021 Rev 3 M74HC126 1 Pin information Pin information Figure 1. Pin connection and IED logic symbols GAMS1212131410CB Table 2. Pin description Pin no Symbol Name and function 1, 4, 10, 13 1G to 4G Output enable input 2, 5, 9, 12 1A to 4A Data inputs 3, 6, 8, 11 1Y to 4Y Data outputs 7 GND Ground (0 V) 14 VCC Positive supply voltage DocID8021 Rev 3 3/14 14 Functional description 2 M74HC126 Functional description Table 3. Truth table A G Y X L Z L H L H H H Figure 2. Input and output equivalent circuit VCC VCC Output Input GND 4/14 GND DocID8021 Rev 3 M74HC126 3 Electrical characteristics Electrical characteristics “Absolute maximum ratings” are those values beyond which damage to the device may occur. Functional operation under these conditions is not implied. Table 4. Absolute maximum ratings Symbol VCC Parameter Value Supply voltage -0.5 to +7 VI DC input voltage VO DC output voltage IIK DC input diode current IOK DC output diode current IO DC output current ± 35 DC VCC or ground current ± 70 ICC or IGND Unit -0.5 to VCC + 0.5 ± 20 500(1) PD Power dissipation Tstg Storage temperature TL Lead temperature (10 sec) V -65 to +150 300 mA mW °C 1. 500 mW at 65 °C; derate to 300 mW by 10 mW/°C from 65 °C to 85 °C Table 5. Recommended operating conditions Symbol VCC Parameter Supply voltage VI Input voltage VO Output voltage Top Operating temperature tr, tf Value Unit 2 to 6 0 to VCC -55 to 125 Input rise and fall time DocID8021 Rev 3 VCC = 2.0 V 0 to 1000 VCC = 4.5V 0 to 500 VCC = 6.0 V 0 to 400 V °C ns 5/14 14 Electrical characteristics M74HC126 Table 6. DC specifications Test condition Symbol VIH VIL Parameter High level input voltage Low level input voltage Value TA = 25 °C VCC (V) Min. Typ. -40 to 85 °C -55 to 125 °C Unit Max. Min. Max. Min. 2.0 1.5 1.5 1.5 4.5 3.15 3.15 3.15 6.0 4.2 4.2 4.2 Max. V 2.0 0.5 0.5 0.5 4.5 1.35 1.35 1.35 6.0 1.8 1.8 1.8 V 2.0 IO = -20 μA 1.9 2.0 1.9 1.9 4.5 IO = -20 μA 4.4 4.5 4.4 4.4 6.0 IO = -20 μA 5.9 6.0 5.9 5.9 4.5 IO = -6.0 mA 4.18 4.31 4.13 4.10 6.0 IO = -7.8 mA 5.68 5.8 5.63 5.60 2.0 IO = 20 μA 0.0 0.1 0.1 0.1 4.5 IO = 20 μA 0.0 0.1 0.1 0.1 6.0 IO = 20 μA 0.0 0.1 0.1 0.1 4.5 IO = 6.0 mA 0.17 0.26 0.33 0.40 6.0 IO = 7.8 mA 0.18 0.26 0.33 0.40 Input leakage current 6.0 VI = VCC or GND ± 0.1 ±1 ±1 μA IOZ High impedance output leakage current 6.0 VI = VIH or VIL VO = VCC or GND ± 0.5 ±5 ± 10 μA ICC Quiescent supply current 6.0 VI = VCC or GND 4 40 80 μA VOH VOL II 6/14 High level output voltage Low level output voltage DocID8021 Rev 3 V V M74HC126 Electrical characteristics Table 7. AC electrical characteristics (Input tr = tf = 6 ns) Test condition Symbol Parameter VCC (V) Value TA = 25 °C CL (pF) Min. Typ. Max. 20 60 75 90 6 12 15 18 6.0 5 10 13 15 2.0 36 75 95 110 9 15 19 22 6.0 8 13 16 19 2.0 52 105 130 160 13 21 26 32 11 18 36 75 9 15 19 22 8 13 16 19 52 105 130 160 13 21 26 32 6.0 11 18 22 27 2.0 48 80 100 120 12 16 20 24 10 14 17 20 2.0 tTLH, tTHL Output transition time 50 4.5 4.5 tPLH, tPHL Propagation delay time 50 4.5 150 6.0 - 2.0 4.5 High impedance tPZL, tPZH output enable time 50 6.0 RL = 1 kΩ 2.0 4.5 High impedance tPLZ, tPHZ output disable time -40 to 85 °C -55 to 125 °C Unit 150 4.5 50 RL = 1 kΩ 6.0 Min. - Max. 22 Min. - 95 Max. ns ns ns 27 110 ns ns ns Table 8. Capacitive characteristics Test condition Sym Value Parameter VCC (V) CIN Input capacitance CPD Power dissipation capacitance(1) 5.0 TA = 25°C Min - Typ Max 5 10 35 -40 to 85 °C -55 to 125 °C Min Min Max 10 - Unit Max 10 - pF 1. CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load (refer to test circuit). Average operating current can be obtained by the following equation: ICC(opr) = CPD x VCC x fIN + ICC/4(per buffer). DocID8021 Rev 3 7/14 14 Electrical characteristics M74HC126 Figure 3. Test circuit GAMS1212131502CB 1. Legend: CL = 50 pF/150 pF or equivalent (includes jig and probe capacitance). R1 = 1 kΩ or equivalent. RT = ZOUT of pulse generator (typically 50 Ω). Table 9. Propagation delay time configuration 8/14 Test Switch tPLH, tPHL Open tPZL, tPLZ VCC tPZH, tPHZ GND DocID8021 Rev 3 M74HC126 Electrical characteristics Figure 4. Waveform 1: propagation delay times (f = 1 MHz; 50 % duty cycle) GAMS1212131506CB Figure 5. Waveform 2: Output enable and disable times (f = 1 MHz; 50 % duty cycle) GAMS1212131517CB DocID8021 Rev 3 9/14 14 Package information 4 M74HC126 Package information In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance. ECOPACK® specifications, grade definitions and product status are available at: www.st.com. ECOPACK® is an ST trademark. 10/14 DocID8021 Rev 3 M74HC126 4.1 Package information SO14 package information Figure 6. SO14 package mechanical drawing / * F & $ D E H D 6 H E ( ' 0   )   *$06&% Table 10. SO14 package mechanical data Dimensions Ref Millimeters Min. Typ. A a1 Inches Max. Min. Typ. 1.75 0.1 0.2 a2 Max. 0.068 0.003 0.007 1.65 0.064 b 0.35 0.46 0.013 0.018 b1 0.19 0.25 0.007 0.010 C 0.5 0.019 c1 45 ° 45 ° D 8.55 8.75 0.336 0.344 E 5.8 6.2 0.228 0.244 e 1.27 0.050 e3 7.62 0.300 F 3.8 4.0 0.149 0.157 G 4.6 5.3 0.181 0.208 L 0.5 1.27 0.019 0.050 M 0.68 0.026 S 8° 8° DocID8021 Rev 3 11/14 14 Package information 4.2 M74HC126 TSSOP14 package information Figure 7. TSSOP14 package mechanical drawing $ $ $ H E . / F ( ' ( 3,1,'(17,),&$7,21  *$06&% Table 11. TSSOP14 package mechanical data Dimensions Ref Millimeters Min. Typ. A Max. Min. Typ. 1.2 A1 0.05 A2 0.8 b Max. 0.047 0.15 0.002 0.004 0.006 1.05 0.031 0.039 0.041 0.19 0.30 0.007 0.012 c 0.09 0.20 0.004 0.0089 D 4.9 5 5.1 0.193 0.197 0.201 E 6.2 6.4 6.6 0.244 0.252 0.260 E1 4.3 4.4 4.48 0.169 0.173 0.176 e 12/14 Inches 1 0.65 K 0° L 0.45 0.60 0.0256 8° 0° 0.75 0.018 DocID8021 Rev 3 8° 0.024 0.030 M74HC126 5 Ordering information Ordering information Table 12. Order codes Order code Temp. range Package Packaging M74HC126RM13TR -55 °C to 125 °C S014 M74HC126YRM13TR(1) -40 °C to 125 °C SO14 (automotive grade) M74HC126TTR -55 °C to 125 °C TSSOP14 M74HC126YTTR(1) -40 °C to 125 °C TSSOP14 (automotive grade) Marking 74HC126 Tape and reel 74HC126Y HC126 HC126Y 1. Qualification and characterization according to AEC Q100 and Q003 or equivalent, advanced screening according to AEC Q001 and Q002 or equivalent. 6 Revision history Table 13. Document revision history Date Revision Aug-2001 1 Initial release. 3 Removed DIP14 package Features: added ESD information Table 1: Device summary: updated order codes, added automotive grade order codes, added temperature range and marking details. Added Section 5: Ordering information. 13-Dec-2013 Changes DocID8021 Rev 3 13/14 14 M74HC126 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. ST PRODUCTS ARE NOT DESIGNED OR AUTHORIZED FOR USE IN: (A) SAFETY CRITICAL APPLICATIONS SUCH AS LIFE SUPPORTING, ACTIVE IMPLANTED DEVICES OR SYSTEMS WITH PRODUCT FUNCTIONAL SAFETY REQUIREMENTS; (B) AERONAUTIC APPLICATIONS; (C) AUTOMOTIVE APPLICATIONS OR ENVIRONMENTS, AND/OR (D) AEROSPACE APPLICATIONS OR ENVIRONMENTS. WHERE ST PRODUCTS ARE NOT DESIGNED FOR SUCH USE, THE PURCHASER SHALL USE PRODUCTS AT PURCHASER’S SOLE RISK, EVEN IF ST HAS BEEN INFORMED IN WRITING OF SUCH USAGE, UNLESS A PRODUCT IS EXPRESSLY DESIGNATED BY ST AS BEING INTENDED FOR “AUTOMOTIVE, AUTOMOTIVE SAFETY OR MEDICAL” INDUSTRY DOMAINS ACCORDING TO ST PRODUCT DESIGN SPECIFICATIONS. PRODUCTS FORMALLY ESCC, QML OR JAN QUALIFIED ARE DEEMED SUITABLE FOR USE IN AEROSPACE BY THE CORRESPONDING GOVERNMENTAL AGENCY. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2013 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 14/14 DocID8021 Rev 3